M-LOCKS EC10-40, EC10-70, ST4005, ST4010, ST4015 Technical Manual

EC10•40 Technical Manual

EC10•40 Technical Manual

CHARACTERISTICS

The EuroLine series was specially developed for safes which have two thru holes,
100 mm apart. The plastic housing of the EuroLine Entry unit combines an alpha­numeric membrane keypad with a pull handle (metal). The 8x8 mm square shaft of
the pull handle drives either the lock or a boltwork. This unit requires a separate
battery box. Battery terminals in the front of the keypad are provided in case
batteries are completely depleted. Cable length is approximately 30 cm.

DIMENSIONS / MOUNTING INSTRUCTION

The diameter of the cable hole should be minimum 9 mm, maximum 12 mm. The
spindle hole should be maximum

Ø 13 mm. Both holes must be deburred well to

avoid damage.

Cut the 8 mm square shaft to an
appropriate length. Make sure the
shaft drives the lock or the boltwork
not just with the tip. Affix the shaft
with the provided screw in the
handle and cover the screw with
the label.

Adjust position and mount the entry unit with M4 flathead screws.
Push the shaft as shown above into the boltwork. Lock and boltwork must be in

the “OPEN” position.

Vlijtstraat 40, NL-7005 BN Doetinchem
Tel: [phone] Fax: [phone]
www.m-locks.com / [e-mail]

EC10•40 Technical Manual

Keep the inside of the housing clean (remove dust). Route
the cable through the cable hole. Route the battery cable in
the opposite direction through the cable hole and push the
white connector into the receptacle on the circuit board.
Make sure the connector is completely seated.

Battery box ST50•65

Remove the protective layer from the adhesive ring on the back of the keypad unit.
Position the keypad and press it into the housing. Make sure the surfaces are dry

and clean, and no cables are in the way. Do not remove and re-apply keypad
once it has been glued in the housing!

Connect one (1) battery to the battery box.

Dimensions of the battery box P/N ST50•65:

Vlijtstraat 40, NL-7005 BN Doetinchem
Tel: [phone] Fax: [phone]
www.m-locks.com / [e-mail]

Only use DURACELL PROCELL 9V-ALKALINE- or Energizer batteries.

EC10•70 Technical Manual

EC10•70 Technical Manual

CHARACTERISTICS

The EuroLine series was specially developed for safes which have two thru holes,
100 mm apart. The plastic housing of the EuroLine Entry unit combines an alpha­numeric membrane keypad with a large boltwork handle. The 8x8 mm square shaft
of the handle drives either the EM15•20 lock or a boltwork. This unit requires a
separate battery box. Battery terminals in the front of the keypad are provided in
case batteries are completely depleted. Cable length is approximately 30 cm.

DIMENSIONS / MOUNTING INSTRUCTION

Cut the 8 mm square shaft to an appropriate length. The shaft should stick out of the
boltwork 5-8 mm and is secured by using the star washer. Note: It is recommended
to deburr the shaft after cutting so it is easier to apply the star washer. If used with
the DirectDrive electronic lock, the shaft should engage approximately 15mm into the
lock. Affix the shaft in the handle with the provided screw and cover the screw with
the label.

star washer

Vlijtstraat 40, NL-7005 BN Doetinchem
Tel: [phone] Fax: [phone]
www.m-locks.com / [e-mail]

EC10•70 Technical Manual

The diameter of the cable hole should be minimum 9 mm, maximum 12 mm. The
spindle hole should be maximum Ø 13 mm. Both holes must be deburred well to
avoid damage.

Adjust position and mount the entry
unit with M4 flathead screws.
Insert the shaft plate into the
housing and push the shaft into the
lock. If the handle drives a boltwork,
put the star washer on the end of
the shaft to secure the handle.

Keep the inside of the housing clean (remove dust). Route
the cable through the cable hole. Route the battery cable in
the opposite direction through the cable hole and push the
white connector into the receptacle on the circuit board.
Make sure the connector is completely seated.

Battery box ST50•65

Remove the protective layer from the adhesive ring on the back of the keypad unit.
Position the keypad and press it into the housing. Make sure the surfaces are dry

and clean, and no cables are in the way. Do not remove and re-apply keypad
once it has been glued in the housing!

Vlijtstraat 40, NL-7005 BN Doetinchem
Tel: [phone] Fax: [phone]
www.m-locks.com / [e-mail]

Only use DURACELL PROCELL 9V-ALKALINE- or Energizer batteries.

ST40xx Technical Manual

Vlijtstraat 40, NL-7005 BN Doetinchem
Tel: [phone] Fax: [phone]
www.m-locks.com / [e-mail]

MODULAR

Technical Manual

CHARACTERISTICS

The height of the EuroLine “Modular“ Series is very low because the battery box is
located inside the safe. It is available with mat chrome (ST40•05) or black plastic
housing (ST40•10, ST40•15). ST40•15 further reduces the height as it is recessed
and almost flush with the door surface. Cable length is approximately 35 cm.The
EuroLine “Modular“ Series includes also several handles and dial assemblies.

DIMENSIONS / MOUNTING INSTRUCTION

The diameter of the cable hole should be minimum 9 mm, maximum 12 mm.
Deburr the cable hole well to avoid damage.

ST40•05, mat chrome, ST40•10 black

ST4005/ ST4010/ ST4015/ ST4020

ST40xx Technical Manual

Vlijtstraat 40, NL-7005 BN Doetinchem
Tel: [phone] Fax: [phone]
www.m-locks.com / [e-mail]

ST40•15 (flush) black

Mount the housing with two M4x8 flathead screws. Keep the inside of the housing

clean (remove dust). Route the cable through the cable hole.
Route the battery cable in the opposite direction through the
cable hole and push the white connector into the receptacle
on the circuit board. Make sure the connector is completely
seated.

Battery box ST50•65

Remove the protective layer from the adhesive ring on the back of the keypad unit.
Position the keypad and press it into the housing. Make sure the surfaces are dry

and clean, and no cables are in the way. Do not remove and re-apply keypad
once it has been glued in the housing!

Connect one (1) battery to the battery box. Only use DURACELL PROCELL 9V­ALKALINE- or Energizer batteries.

Dimensions of the battery box: