ML Accessories BL12ALED User guide

INSTALLATION & MAINTENANCE MANUAL

BL12ALED / BL20ALED

GENERAL INSTRUCTIONS

These instructions should be read carefully and retained after installation by the
end user for future reference and maintenance.
These instructions should be used to aid installation of the following products:
BL12ALED / BL20ALED

SAFETY

• This product must be installed in accordance with the latest edition of the IEE Wiring
Regulations (BS7671) and current Building Regulations. If in any doubt, consult a
qualified electrician

• Please isolate mains prior to installation or maintenance

• Check the total load on the circuit (including when this luminaire is fitted) does not
exceed the rating of the circuit cable, fuse, or circuit breaker

• Please note the IP (Ingress Protection) rating of this product when deciding the location
for installation

• This product is Class II double insulated

• This product is IP54 rated

INSTALLATION

Note - If this luminaire is being used in conjunction with an external PIR or sensor, please
confirm with the manufacturer of the sensors that they are compatible with LED luminaires.

• Provide power to the required point of installation (refer to BS7671 for correct cabling
methods). Suitable IP rated junction boxes should be used where required

• Rotate the diffuser anti-clockwise and remove (see Fig. 1)

Fig. 1

• Remove the fastening screw securing the LED plate and open the LED plate (see Fig. 2)

Fig. 2

• Mark the location of the fixing holes and drill the holes ensuring not to infringe with any
gas/water pipes or electrical cables

• Feed the mains cable through the rubber grommet to retain IP rating, and secure the
baseplate to the surface

• Connect the luminaire to the mains supply ensuring the correct polarity is observed
(see Fig. 3): L – Live (brown), E – Earth (green/yellow), N – Neutral (blue). The earth
terminal is non-functional and only provided for convenience. Two cables can be inserted
into the push-fit terminal block in order to achieve loop-in/loop-out wiring

Fig. 3

• Refasten the LED plate screw

• Reattach the diffuser by rotating clockwise

• Switch on and check for correct operation

WARNING

This product must be disconnected from the circuit if subjected to any high voltage or
insulation resistance testing. Irreparable damage will occur if this instruction is not followed.

GENERAL

This product contains a light source of energy efficiency class E to Regulation (EU) No.
2019/2015 and (UK) 2021 No. 1095.
This product contains a light source which can be replaced by the end user and a control
gear which can be replaced by a professional.

Clean the external surfaces with a damp cloth using a mild solution of detergent and warm
water only, do not use aggressive cleaning products or solvents which may damage the
product.
This product is non-dimmable.
This product should be dismantled for disposal when it reaches the end of its life. Please
see website for dismantling instructions.
This product should be recycled in the correct manner when it reaches the end of its life.
Check local authorities for where facilities exist.

WARRANTY

This product has a warranty of 3 years from date of purchase. Failure to install this product
in accordance with the current edition of the IEE Wiring Regulations (BS7671), improper
use, or removal of the batch code will invalidate the warranty. If this product should fail
within its warranty period, it should be returned to the place of purchase for a free of
charge replacement. ML Accessories does not accept responsibility for any installation
costs associated with the replacement product. Your statutory rights are not affected. ML
Accessories reserve the right to alter product specification without prior notice.

Supplied By:

ML Accessories Ltd, Unit E Chiltern Park, Boscombe Road,

Dunstable LU5 4LT, www.mlaccessories.co.uk

nnuks Holding GmbH, Niederkasseler Lohweg 18, 40547

(UK) Manufacturer

(EU) Authorised Representative

Düsseldorf, Germany

Email: [e-mail]

-20

~40°C

TA

53

AKAPR22_V1