MK Electric K5837WHI, K5837BLK, K5837SGRY, K5837SCW User Manual

The USB Charger is suitable for charging portable electronic
devices connected via a USB 2.0 type A plug.

The USB Charger is suitable for use with all ranges of MK Euro
frontplates with at least a 2 module (50x50mm) aperture.

Rated mains supply voltage..........................220 to 240V a.c.

Mains frequency.........................................................50/60Hz

Rated input current.........................................................60mA

Power consumption (in standby)........................................0W

Output Voltage...............................................................5Vd.c.

Output Current..........................................................2.0A max

Total output Power............................................................10W

Charging Sockets............................................USB 2.0 type A

Operating temperature..........................................0°C to 40°C

Storage temperature..........................................-20°C to 70°C

Twin Charging Sockets: The USB Charger comes with two
charging sockets capable of delivering a total maximum charging
current of 2A. This can be delivered to either socket or divided
between the two as required and controlled by the devices being
charged.

Zero Standby: The USB Charger will draw no current from the
mains until a connector is inserted into either connection port.

Safety Isolation: The output of this product is fully isolated at
SELV level to provide maximum protection for your safety.

Output Overload Protection: The USB Charger is protected
against over-current and short circuit conditions on the output.

3

2

A. INTRODUCTION

B. PRODUCT FEATURES

54

The USB Charger complies with the following EC directives:

Low Voltage Directive (73/23/EEC)
Electro-Magnetic Compatibility Directive (89/336/EEC)

They also comply with the requirements of the following
Standards:

IEC 61558-2-16
IEC 61000-6-1 and IEC 61000-6-3

D. STANDARDS & EC DIRECTIVES

USB Charger
Euro Module

K5837WHI, K5837BLK, K5837SGRY,
K5837SCW

Contents
A Introduction

2

B Product Features

2

C Specification

3

D Standards & EC Directives

4

E Safety Instructions

5

F Installation

7

G Maintenance & Disposal

10

H Guarantee

11

Please leave this leaflet with the end user
for future reference

50078098.001_Rev.A

by Honeywell

E. SAFETY INSTRUCTIONS

6

®

C. SPECIFICATION

1. To prevent the risk of electrocution, turn off the mains

electricity supply before commencing work on the instal­lation of this product.

2. To ensure safe installation:

- This product must be installed by a competent person
(e.g. a qualified electrician) in accordance with these
instructions and the appropriate current national wiring
regulations, (e.g. the IEE wiring regulations BS 7671).

- Where the mounting box incorporates an earth terminal,
it must be connected to the circuit protective (Earth) con­ductor.

NOTE: All bare earth wires must be covered with appro­priate green/yellow sleeving.

- It is essential that all connections are made as instructed,
that the cables are not stressed and that the terminal
screws are fully tightened.

3. This product MUST NOT be installed in bathrooms,
washrooms or any location subject to splashes of water,
condensation or excessively damp conditions.

4.Ensure that the product is mounted on an even surface in
the vertical plane.

5.Do not use the USB Charger in ambient temperatures
higher than the maximum specified operating temperature.

6. This product contains no user serviceable parts. DO NOT
attempt to open the module as this will invalidate your
warranty.

NOTE: The front surface of this product will naturally become warm
in use. This is normal and is not a cause for concern

IMPORTANT:

Refer to Safety Instructions (E), before starting work.

The supply to this product must be protected by a class
B or C MCB with a maximum rating of 32A.

1. Turn off the mains electricity supply.

2.Select the appropriate flush mounting wall box from the
table below based on the thickness of MK Euro Frontplate
the USB Charger is to be mounted in.

Ensure the wall box is firmly secured to the wall.

The product may be cleaned with a dry soft lint free cloth.
Do not use water or any abrasive, solvent based or aerosol
cleaners as this may damage, discolour or affect the finish
and safety of the product.

At the end of their useful life the packaging, product and
where applicable batteries, should be disposed of via a suit­able recycling centre. Do not dispose of with your normal
household waste. Do not burn.

87

11

12

The Company undertakes to replace or repair, at its discre­tion, this product should it become defective within a period
of 2 years after delivery, solely as a result of faulty materials
and/or workmanship. Understandably, if the product has not
been installed or maintained in accordance with the
Company’s instructions, has not been used appropriately, or
if any attempt has been made to rectify, dismantle or alter
the product in any way, the guarantee will be invalidated.

This Guarantee states the Company’s entire liability. It does
not extend to cover consequential loss or damage or instal­lation costs arising from the defective product. This
Guarantee does not restrict or infringe the normal statutory
or other rights of the consumer.

MK Electric Limited wishes to make it clear that it will take all
necessary legal action in any part of the world against any
party found to be manufacturing, distributing, selling or other­wise dealing with any article which infringes the company’s
design rights, copyrights or patents in its products, or any
other rights of the company therein.

H. GUARANTEE

®

by Honeywell

MK Electric

The Arnold Centre, Paycocke Road, Basildon,

Essex SS14 3EA. UK

Technical Help

Tel: [phone]

Fax: [phone]

email: [e-mail]

Customer Service

Tel: [phone]

Fax: [phone]
Fax: [phone] (International)
email: [e-mail]

web site: www.mkelectric.com

Novar ED&S Ltd (A Honeywell Company),

Arlington Business Park, Bracknell, Berkshire, RG12 1EB

Registered no. 189291 (England)

All marks in this document identified with a R or TM symbol

adjacent to the mark are Trade Marks of Novar ED&S Ltd.

NOTE: When using a box with four mounting lugs, it may be
necessary to bend down flat, the top and bottom lugs.

1. Fix the Euro frontplate to the wall box and feed the wiring out
through the aperture.

2. Strip back the outer cable sheath and trim the inner cables to
length to allow cable ends to reach terminals. Carefully strip
the inner cable insulation to expose 8mm of wire.

3. Connect the Live and Neutral cables to the charger.

Live = brown Neutral = blue

NOTE: Some countries and existing installations may also
use the following cable colours:

Live = red Neutral = black

4. Any bare earth conductors must be fitted with an appropriate
length of green/yellow insulating sleeve and properly terminat­ed with a connector.

If the mounting box is provided with an earth terminal, connect
the earth conductor to the terminal.

5. Carefully push the wired charger into the frontplate until the
snap fits have fully engaged. Ensure that cables are not
trapped or pinched.

6. The completed installation should be tested in accordance with
the current wiring regulations by a qualified electrician.

Leave these instructions with the end user for future reference.
Remaining Packaging can safely be disposed of via standard
recycling facilities.

If you are in any doubt regarding the application or installation of
this product, please contact MK Technical Sales Service
Department.

F. INSTALLATION

10

G. MAINTENANCE AND DISPOSAL

9

MK Euro Frontplate

Thickness

Flush Metal Box MK

List No.

>7 mm 866ZIC (35 mm)

<7 mm 877ZIC (46 mm)

by Honeywell