mk-dent AM1116 User Manual

Manufacturer:
MK-dent GmbH

Eichenweg 7b
D-22941 Bargteheide
Germany

Contact:

Phone: [phone]
Fax: [phone]
email: [e-mail]
Internet: www.mk-dent.com

0123

Instruction for use and hygiene

MK-dent Air Motor AM1116

Important Details

The MK-dent Air Motor (AM1116)

- is only intended for dental treatment of patients.

- is according to relevant national regulations as a medical device.
These provisions indicate, that

- applicable accident prevention regulations and health and safety regulations must be observed.

- only a competent user is allowed to use the product according to this instruction.

- only faultless work equipment is to be used.

- any contamination from the product must be avoided.

- patients, users and third parties are to be protected from danger.

Technical Facts

MK-dent Air Motor (AM1116)
Input speed: 5.000 - 15.000 rpm
Air input: 2,2 - 2,8 bar
Air use: up to 60Nl/ min.
Connection: 4-hole standard connection, INTRAmatic connector

Meaning of Symbols

Item No. Serial No. Caution! Sterilizable in an autoclave

up to max. 135°C/ 275°F

Suitable for spray- and

wipe disinfection

Connection to the Treatment Unit

Before rst use and after each use, sterilize the Air Motor. Always use dry, cleaned and decontaminated compressed

air. Premature wear from contaminated and humid compressed air can shorten the lifetime of the product.

Place the connection of the turbing on the Air Motor and
turn the thread until stop.

Spray Regulation

Regulate the amount of water by turning the regulation ring
at the back of the Air Motor.

Checking the Compressed Air with a Manometer

Install the manometer between tubing and Air Motor. The following values should be displayed:

Forced Air (F.A./ T.R.) = 2,2 - 2,8 bar
Return Air (R.A./ R.L.) < 1,1 bar
Water (W.) = 0,8 - 2,5 bar
Spray Air (S.A./ Spr.L.) = 1,0 - 4,0 bar

Connecting to the INTRAmatic-connection of Handpieces

Place the handpiece on the Air Motor until it audibly locks in place.

In order to avoid damage to the driver, do not attach or release the Air Motor while the handpiece is in movement.

Rev: A/09_2015 File: Manual_AM1116_EN.indd

REF SN

Speed Control/ Change Direction of Rotation

Turn the control ring to change the speed and the rotation direction.

Disinfektion

The MK-dent Air Motor can be disinfected externally. Only use DGHM listed chemical disinfectant for spray and wipe disinfection.

Don‘t place the Air Motor in disinfectant baths. Results are mulfunctions.

Lubrication with Oil

Use “MK-dent Premium Service Oil” for care and lubrication. Remove the Air Motor
from the tubing, attach the enclosed MK-dent oil adapter on the oil can and spray for
1-2 seconds in the smaller one of the two large pipelines (see drawing).

Sterilization

Sterilize the MK-dent Air Motor in an autoclave up to max. 135°C (2 bar) / 275°F (29 psi).
Autoclave three times with an initial vacuum for at least 4 minutes at 134°C +/- 1
Autoclave using the gravitation method for at least 10 minutes at 134°C +/- 1
Autoclave using the gravitation method for at least 60 minutes at 121°C +/- 1
Follow the manufacturer‘s instructions for use.

The prepared instrument must be stored protected germ-free from dust in a dry, dark and cool room.

Observe the expiration date of the sterilized item. No chlorine-based products and no chemical solvents or cleaning materials
must be used. Do not use dryer (post-heat). Do not sterilize the packing box.

Caution

Stop working with the contra angle handpiece by higher and irregular running noise, signicant vibrations, overheating,
and optical damaging. Please contact in these cases an authorized by the manufacturer repair center or your dental-depot.

Warranty

If you consider the above points, you will have many years of joy with your product. If you still have complaints, we grant a 1-year warranty.

Rev: A/09_2015 File: Manual_AM1116_EN.indd