![](/html/d9/d9f7/d9f7a25f14f10c856636e4874b5c88f52208cb3ab6fd44e7cb78ca16af8b173b/bg1.png)
MINI SPOT MOVING HEAD LIGHT
Inno Pocket Spot Pearl
MJ-1025
INSTRUCTION MANUAL
Thank you for choosing our LED mini spot moving head light. For the sake of your safety,
Please read and follow these instructions carefully and keep this manual in a safe place for
future reference.
![](/html/d9/d9f7/d9f7a25f14f10c856636e4874b5c88f52208cb3ab6fd44e7cb78ca16af8b173b/bg2.png)
Inno Pocket Spot Pearl MJ-1025 User Manual ver1.0
www.mjledlighting.com
Catalogue
Chapter Page
Safe Usage Of The Product -----------------------------------------------------------------------------------------3
Install The Equipment ------------------------------------------------------------------------------------------------4
DMX Set Up -------------------------------------------------------------------------------------------------------------5
System Menu ------------------------------------------------------------------------------------------------------------7
Home Adjustment Menu --------------------------------------------------------------------------------------------10
Operation Menu --------------------------------------------------------------------------------------------------------11
Master-Slave Set Up---------------------------------------------------------------------------------------------------12
Remote Operation---------------------------------------------------------------------------------------------------- --12
DMX Channel Mode---------------------------------------------------------------------------------------------------13
Photometric Chart-------------------------------------------------------------------------------------------------------14
Dimmer Curve Chart---------------------------------------------------------------------------------------------------15
Fuse Replacement-------------------------------------------------------------------------------------------------------15
Cleaning--------------------------------------------------------------------------------------------------------------------15
Trouble Shooting---------------------------------------------------------------------------------------------------------16
Specifications---------------------------------------------------------------------------------------------------------- ---16
☆Important notice:
· In this instruction for use contains about the installment and the use aspect important information of the LED moving
head. When installing and using, you need to look this usage instruction strictly.
· Before open the LED moving head and if you want to do the repair work, please make sure the power source is at the
separation condition.
· Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and the unit are
in good condition before installation and use. Should there be any damage caused by transportation, consult your dealer
and do not use the unit. Any damage caused by improper use will not be assumed by the manufacturer or dealer.
Attention: Unceasingly carries on the product improvement about our company the policy, in this instruction booklet
carries the data will have the possibility to be able to change in the future, when no longer separate notice change matters
concerned. Our company retains when the product improvement changes the related specification the authority. This
instruction booklet publisher cannot be responsible regarding this instruction booklet in information accuracy, also cannot
the related consequence which causes regarding these information be responsible.
![](/html/d9/d9f7/d9f7a25f14f10c856636e4874b5c88f52208cb3ab6fd44e7cb78ca16af8b173b/bg3.png)
Inno Pocket Spot Pearl MJ-1025 User Manual ver1.0
www.mjledlighting.com
SAFE USAGE OF THE PRODUCT
When unpacking and before disposing of the carton, check there is no transportation damage before
using the product. Should there be any damage caused by transportation, consult your dealer and do
not use the apparatus.
The product is for indoor use only, IP20. Use only in dry locations. Keep this device away from rain
and moisture, excessive heat, humidity and dust. Do not allow contact with water or any other
liquids.
The product is not designed or intended to be mounted directly on to inflammable surfaces
The product is only intended for installation, operation and maintenance by professional person.
The product must be installed in a location with adequate ventilation, at least 50cm from MJacent
wall surfaces. Be sure that no ventilation slots are blocked.
Do not product the beam onto inflammable surfaces, minimum distance is m.
Avoid direct exposure to the light from the lamp. The light is harmful to the eye.
Do not attempt to dismantle or modify the projector in any way.
Electrical connection must only be carried out by qualified personnel.
Before installation, ensure that the voltage and frequency of power supply match the power
requirements of the projector.
It is essential that each projector is correctly earthed and that electrical installation conforms to all
relevant standards.
Do not connect this device to any other types of dimmer apparatus.
Make sure that the power-cord is never crimped or damaged by sharp edges. Never let the
power-cord come into contact with other cables. Only handle the power-cord by the plug. Never pull
out the plug by tugging the power-cord.
Keep the optical system clean. Do not touch the lens with bare hands.
The product should always be installed with a secondary safety fixing. On the projector base brink,
there is a hole for the safety cord provided. It should be attached as shown in “installing the
projector” section.
The lens shall be changed if they have become visibly damaged to such an extent that their
effectiveness is impaired, for example by cracks or deep scratches.
Exterior surface temperatures of the luminaire after 5 minutes operation is 40°C,when steady state is
achieved 50°C.
There is no user serviceable parts inside the projector, do not open the housing and never operate the
product with the covers removed.
If you have any questions, don’t hesitate to consult your dealer or manufacturer.
★Always disconnect from the mains, when the device is not in use or before cleaning it or
before attempting any maintenance work !
![](/html/d9/d9f7/d9f7a25f14f10c856636e4874b5c88f52208cb3ab6fd44e7cb78ca16af8b173b/bg4.png)
Inno Pocket Spot Pearl MJ-1025 User Manual ver1.0
www.mjledlighting.com
Install The Equipment:
When installing the unit, the trussing or area of installation must be able to hold 10 times the weight without
any deformation. When installing the unit must be secured with a secondary safety attachment, e.g. and
appropriate safety cable. Never stand directly below the unit when mounting, removing, or servicing the unit.
Overhead mounting requires extensive experience, including calculating working load limits, installation
material being used, and perodic safety inspection of all installation material and unit. If you lack these
qualifications, do not attempt the installation yourself.
The installation should be checked by a skilled person once a year.
The Inno Pocket Spot Pearl is fully operational in two different mounting positions, hanging upside-down
from a ceiling or set on a flat level surface. To avoid internal damage to the unit, never mount the unit on its
side as illustrated above. Be sure this fixture is kept at least 0.5m away from any flammable materials
(decoration etc.). Always use and install the supplied safety cable as a safety measure to prevent accidental
damage and/or injury in the event the clamp fails (see next page).
NOTICE: The suitable enviromental temperature for this lighting fixture is between -25˚ C to 45˚ C. Do not place
this lighting fixture in an enviroment where the temperatures are under or above the temperatures stated above.
This will allow the fixture to run at its best and help prolong the fixture life.
![](/html/d9/d9f7/d9f7a25f14f10c856636e4874b5c88f52208cb3ab6fd44e7cb78ca16af8b173b/bg5.png)
Inno Pocket Spot Pearl MJ-1025 User Manual ver1.0
www.mjledlighting.com
Screw one clamp via a M12 screw and nut to the included bracket. Attach the bracket using the included
screws to the bottom of the Inno Pocket Spot Pearl. Attach the eyehole screw to the bottom of the base
and pull the safety-cable through the screw and over the trussing system or a safe fixation spot. Insert the
end in the carabine and tighten the safety screw.
DMX Set Up
Power Supply: The MJ Inno Pocket Spot Pearl contains a automatic voltage switch, which will auto sense the
voltage when it is plugged into the power source. With this switch there is no need to worry about the correct
power voltage, this unit can be plugged in anywhere.
DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used by most lighting and controller
manufactures as a form of communication between intelligent fixtures and controllers. A DMX controller sends
DMX data instructions from the controller to the fixture. DMX data is sent as serial data that travels from fixture to
fixture via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only
have a DATA “OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models of different manufactures to be linked together
and operate from a single controller, as long as all fixtures and the controller are DMX compliant. To ensure proper
DMX data transmission, when using several DMX fixtures try to use the shortest cable path possible. The order in
which fixtures are connected in a DMX line does not influence the DMX addressing. For example; a fixture