Mittler Bros Machine & Tool 2200-M User Manual
10
10
16
ITEM
NO.
8
1 2200-006 Pinion 1
PART NUMBER Description Qty.
2 2200-503 7/8 Bronze Bushing 1
3 2200-502 1 1/4 Bronze Bushing 1
4 2200-501 1 1/2 Bronze Bushing 2
5 750-FW-0.625-SAE Flat Washer (SAE) 1
6 750-SHCS-0.375-16X1.000 SHCS 3/8-16 x 1" 1
7 2200-008 Handle 1
8 2200-005 Ram 1
15
4
13
14
1
11
9 2200.M Manual Press Frame 1
7
3
12
10 750-BHCS-.0500-13X1.000 BHCS 1/2-13 x 1" 2
11 750-FLANGENUT-0.375-16 3/8-16 Flange Nut 1
12 2200-099 Plastic Snap 1
13 2200-098 Holding Pin 1
14 2200-029-M Front Cover Plate 1
15 2200-513 3/8-16 Tab Screw 1
16 2200-005-HD HD Ram 1
4
17 2200-015A Scrap Ejector Assembly 1
20 1/2-20 x 1" SBHCS Drilled Thru 1
6
21 Ejector Pin Ejector Pin 1
22 2200-015 Ejector Lever 1
5
23 1/2-13 x 4-1/2" HHCS 1
24 1/2-13 Nylock Half Nut 1
2
Included
#2200-SLC
Spring Loaded
Center Assm
#2200-011
Upper Adaptor Nut
w/ 1/2-20 x 2" FHCS
#2200-034
Wrench
#2200-012
Lower Adaptor Nut
w/ 1/2-20 x 1" Button Bolt
5
17
See Detail A
9
23
24
6/17/2010
5/19/2011
PROPRIETAR Y AND CONFIDENT IAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MITTLER BROS. MACHINE & TOOL. ANY
REPRODUCT ION IN PART OR A S A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MITTLER BROS. MACHINE & TOOL IS
PROHIBITED.
USED ONNEXT ASSY
APPLICATION
4 3 2
UNLESS OTH ERWISE SPECIFIED:
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL ±.015
ONE PLACE DECIMAL ±.015
TWO PLACE DECIMAL ±.010
THREE PLACE DECIMAL ±.005
ANGULAR ±1°
QUANTITY
MATERIAL
yyyy
FINISH
DO NOT SCALE DRAWING
22
DRAWN
CHECKED
ENG APPR.
MFG APPR.
Q.A.
COMMENTS
NAME
RAJ
Adaptor Nut
Scrap Ejector
DATE
07/15/08
10 Cooperative Way, Wright City, MO. 63390
(636)745-7757 Fax (636)745-2874
TITLE:
MANUAL BENCH PRESS
SIZE
A
SCALE: 1:16 SHEET 1 OF 2
2200-M A
WEIGHT: 60.794
2200-012
Detail A
Assembly
REVDWG. NO.
1
Spring
Spring Button
Spring
Loaded Pin
Upper Adaptor
Nut 2200-011
Flare Ring
Punch
1/2-20 x 2"
C'Sunk Spring
Loaded Bolt
1/2-20 x 1"
Button Head
Bolt
Die
ASSEMBLY:
Remove ½” - 20 Bolt and Bearing from
·
Punch & Flare Tool - set bolt / bearing aside.
Install Button Head Bolt through Female Die.
·
Install Lower Adaptor Nut #2200-012 through
·
hole in Lower Platen Tooling Plate
Thread Button Head Bolt into Lower
·
Adaptor Nut -
Install Ejector Pin through Button Head
·
DO NOT Tighten
.
Bolt - See Drawing
Install ½”-20 Countersunk Bolt through
·
Punch and Male Flare Ring.
Install and Tighten ½”-20 Bolt into Upper
·
Adaptor Nut #2200-011.
Install Spring Load Pin through center
·
of Bolt - See Drawing.
Place a dab of grease on bottom of Spring
·
Button to assist in Spring Button to
Spring Loaded Pin Alignment.
Place Spring Button on Bolt head.
·
Install Spring over tab on Spring Button.
·
Carefully Install Spring Loaded Assembly
·
into Upper Ram Cavity while Threading
Upper Adaptor Nut onto Ram.
Tighten Upper Adaptor Nut using
·
Wrench #2200-034.
Lower Upper Ram / Punch / Male Flare
·
Ring Assembly.
Align Female Die with Punch by moving
·
Female Die.
Lower Assembly onto Lower Tooling Plate.
·
Tighten Lower Adaptor Nut using
·
Wrench #2200-034.
Lower Adaptor
Nut 2200-012
UNLESS OTH ERWISE SPECIFIED:
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL ±.015
ONE PLACE DECIMAL ±.015
TWO PLACE DECIMAL ±.010
THREE PLACE DECIMAL ±.005
ANGULAR ±1°
PROPRIETAR Y AND CONFIDENT IAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MITTLER BROS. MACHINE & TOOL. ANY
REPRODUCT ION IN PART OR A S A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MITTLER BROS. MACHINE & TOOL IS
PROHIBITED.
5
4 3 2
USED ONNEXT ASSY
APPLICATION
QUANTITY
MATERIAL
yyyy
FINISH
DO NOT SCALE DRAWING
DRAWN
CHECKED
ENG APPR.
MFG APPR.
Q.A.
COMMENTS
NAME
BAB
DATE
5/31/11
10 Cooperative Way, Wright City, MO. 63390
(636)745-7757 Fax (636)745-2874
TITLE:
Punch & Flare Assembly
SIZE
A
SCALE: 1:8
2200-M
WEIGHT: 4.291
1
REVDWG. NO.
SHEET 2 OF 2
Loading...