Mitsumi electronic HC3200 User Manual
DLPTM PROJECTOR
MODEL
HC3200
User Manual
HC3200
This User Manual is important to you.
Please read it before using your projector.
EN-2
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert
the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure
that may be of sufficient magnitude to constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION:
TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD,
RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE
EXPOSURE.
NOTE:
SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR
THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE.
WARNING
Use the attached specified power supply cord. If
you use another power supply cord, it may cause
interference with radio and television reception.
Use the attached RGB cable with this equipment so as
to keep interference within the limits of an FCC Class B
device.
This apparatus must be grounded.
DO NOT LOOK DIRECTLY INTO THE LENS WHEN
THE PROJECTOR IS IN THE POWER ON MODE.
CAUTION
Not for use in a computer room as defined in the
Standard for the Protection of Electronic Computer/
Data Processing Equipment, ANSI/NFPA 75.
When using the projector in Europe:
COMPLIANCE NOTICE
This projector complies with the requirements of
the EC Directive 2004/108/EC “EMC Directive” and
2006/95/EC “Low Voltage Directive”.
The electro-magnetic susceptibility has been chosen
at a level that gains proper operation in residential
areas, on business and light industrial premises and on
small-scale enterprises, inside as well as outside of the
buildings. All places of operation are characterised by
their connection to the public low voltage power supply
system.
WARNING
Use the attached RGB cable with this equipment so
as to keep interference within the limits of an EN55022
Class B device.
Please follow WARNING instructions.
Contents
Important safeguards.........................................................................................................................4
Preparing your projector ....................................................................................................................6
Using the remote control ...............................................................................................................8, 9
Setting up your projector .................................................................................................................10
Viewing video images ......................................................................................................................14
Viewing computer images ...............................................................................................................22
Menu operation ................................................................................................................................25
Adjusting projected images .............................................................................................................31
Advanced features ...........................................................................................................................35
Replacing the lamp ..........................................................................................................................36
Maintenance ....................................................................................................................................39
Troubleshooting ...............................................................................................................................40
Indicators .........................................................................................................................................44
Specifications ..................................................................................................................................45
Note: This symbol mark is for EU countries only.
This symbol mark is according to the directive 2002/96/EC Article 10 Information
for users and Annex IV, and/or to the directive 2006/66/EC Article 20 Information
for end-users and Annex II.
Your MITSUBISHI ELECTRIC product is designed and manufactured with high quality materials and components
which can be recycled and/or reused.
This symbol means that electrical and electronic equipment, batteries and accumulators, at their end-of-life, should be
disposed of separately from your household waste.
If a chemical symbol is printed beneath the symbol shown above, this chemical symbol means that the battery or
accumulator contains a heavy metal at a certain concentration. This will be indicated as follows:
Hg: mercury (0,0005%), Cd: cadmium (0,002%), Pb: lead (0,004%)
In the European Union there are separate collection systems for used electrical and electronic products, batteries and
accumulators.
Please, dispose of this equipment, batteries and accumulators correctly at your local community waste collection/
recycling centre.
Please, help us to conserve the environment we live in!
Declaration of Conformity
Model number: HC3200
Trade name: MITSUBISHI ELECTRIC
Responsible party: Mitsubishi Digital Electronics America, Inc.
9351 Jeronimo Road, Irvine, CA 92618 U.S.A
Telephone number: +1-(949) 465-6000
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Trademark, Registered trademark
DLPTM, Digital Micromirror Device, DMD, and BrilliantColorTM are all trademarks of Texas Instruments.
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing LLC.
Other brand or product names are trademarks or registered trademarks of their respective holders.
EN-3
EN-4
Important safeguards
Please read all these instructions regarding your
projector and retain them for future reference. Follow all
warnings and instructions marked on the projector.
Read instructions
1.
All the safety and operating instructions should be
read before the appliance is operated.
Retain instructions
2.
The safety and operating instructions should be
retained for future reference.
Warnings
3.
All warnings on the appliance and in the operating
instructions should be adhered to.
Instructions
4.
All operating instructions must be followed.
Cleaning
5.
Unplug this projector from the wall outlet before
cleaning it. Do not use liquid aerosol cleaners. Use
a damp soft cloth for cleaning.
Attachments and equipment
6.
Never add any attachments and/or equipment
without the approval of the manufacturer as such
additions may result in the risk of fire, electric shock
or other personal injury.
Water and moisture
7.
Do not use this projector near water or in contact
with water.
Accessories
8.
Do not place this projector on an unstable cart,
stand, tripod, bracket or table. Use only with a
cart, stand, tripod, bracket, or table recommended
by the manufacturer or sold with the projector.
Any mounting of the appliance should follow
the manufacturer’s instructions and should use
a mounting accessory recommended by the
manufacturer.
An appliance and cart combination should be
moved with care. Quick stops, excessive force and
uneven surfaces may cause the appliance and cart
combination to overturn.
Ventilation
9.
Slots and openings in the cabinet are provided
for ventilation, ensuring reliable operation of the
projector and to protect it from overheating. Do not
block these openings or allow them to be blocked
by placing the projector on a bed, sofa, rug, or
bookcase. Ensure that there is adequate ventilation
and that the manufacturer’s instructions have been
adhered to.
Power sources
10.
This projector should be operated only from the type
of power source indicated on the marking label. If
you are not sure of the type of power, please consult
your appliance dealer or local power company.
Power-cord protection
11.
Power-supply cords should be routed so that
they are not likely to be walked on or pinched
by items placed upon or against them. Pay
particular attention to cords at plugs, convenience
receptacles, and points where they exit from the
appliance. Do not put the power cord under a
carpet.
Overloading
12.
Do not overload wall outlets and extension cords as
this can result in a fire or electric shock.
Objects and liquids
13.
Never push objects of any kind through openings of
this projector as they may touch dangerous voltage
points or short-out parts that could result in a fire or
electric shock. Never spill liquid of any kind on the
projector.
Servicing
14.
Do not attempt to service this projector by yourself.
Refer all servicing to qualified service personnel.
Damage requiring service
15.
Unplug this projector from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
(a) If the power-supply cord or plug is damaged.
(b) If liquid has been spilled, or objects have fallen
into the projector.
(c) If the projector does not operate normally after
you follow the operating instructions. Adjust only
those controls that are covered by the operating
instructions. An improper adjustment of other
controls may result in damage and may often
require extensive work by a qualified technician
to restore the projector to its normal operation.
(d) If the projector has been exposed to rain or
water.
(e) If the projector has been dropped or the cabinet
has been damaged.
(f) If the projector exhibits a distinct change in
performance - this indicates a need for service.
Replacement parts
16.
When replacement parts are required, be sure
that the service technician has used replacement
parts specified by the manufacturer or parts having
the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric
shock or other hazards.
Safety check
17.
Upon completion of any service or repair to this
projector, ask the service technician to perform
safety checks determining that the projector is in a
safe operating condition.
Important safeguards (continued)
WARNING:
Unplug immediately if there is something wrong
with your projector.
Do not operate if smoke, strange noise or odor comes
out of your projector. It might cause fire or electric shock.
In this case, unplug immediately and contact your dealer.
Never remove the cabinet.
This projector contains high voltage circuitry. An
inadvertent contact may result in an electric shock.
Except as specifically explained in the User Manual do
not attempt to service this product by yourself. Please
contact your dealer when you want to fix, adjust or
inspect the projector.
Do not modify this equipment.
It can lead to fire or electric shock.
Do not keep using the damaged projector.
If the projector is dropped and the cabinet is damaged,
unplug the projector and contact your dealer for
inspection. It may lead to fire if you keep using the
damaged projector.
Do not face the projection lens to the sun.
It can lead to fire.
Use correct voltage.
If you use incorrect voltage, it can lead to fire.
Do not place the projector on uneven surface.
Place the projector on a leveled and stable surface only.
Please do not place equipment on unstable surfaces.
Do not look into the lens when the projector is
operating.
It may hurt your eyes. Never let children look into the
lens when it is on.
Do not unplug the power cord during operation.
It can lead to lamp breakage, fire, electric shock or
other trouble. It is best to wait for the fan to turn off
before turning the main power off.
Do not touch the air outlet grille and bottom plate,
which become hot.
Do not touch them or put other equipment close to
the air outlet grilles because they become hot during
operation. The heated air outlet grilles and bottom plate
may cause injury or damage to other equipment.
Also, do not put the projector on a desk that is easily
affected by heat.
Do not look into the air outlet grille when projector
is operating.
Heat, dust, etc. may blow out of it and hurt your eyes.
Do not block the air inlet and outlet grilles.
If they are blocked, heat may be generated inside the
projector, causing deterioration in the projector quality
and fire.
Do not use flammable solvents (benzene, thinner,
etc.) and flammable aerosols near the projector.
Flammable substances may ignite causing fire or
breakdown because the temperature inside the
projector rises very high while the lamp is illuminating.
Do not use the projector with condensation on it.
It can lead to breakdown or other failure.
Place of installation
For safety’s sake, refrain from setting the projector
at any place subjected to high temperature and high
humidity. Please maintain an operating temperature,
humidity, and altitude as specified below.
Operating temperature: between +41°F (+5°C) and
•
+95°F (+35°C)
Operating humidity: between 30% and 90%
•
Never put any heat-producing device under the
•
projector so that the projector does not overheat.
Do not install the projector to a place that is
•
unstable or subjected to vibration.
Do not install the projector near any equipment that
•
produces a strong magnetic field.
Also refrain from installing the projector near any
cable carrying a large amount of current.
Place the projector on a solid, vibration free surface;
•
otherwise it may fall, causing serious injury or
damage.
Do not stand the projector on its end. It may fall,
•
causing serious injury or damage.
Slanting the projector more than ±10°(right and
•
left) or ±15°(front and rear) may cause trouble or
explosion of the lamp.
Do not place the projector near air-conditioning unit,
•
heater, or humidifier to avoid hot or moist air to the
exhaust and ventilation hole of the projector.
COMPLIANCE NOTICE OF FCC
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•
Consult the dealer or an experienced Radio/TV technician for help.
•
Changes or modifications not expressly approved by Mitsubishi could void the user’s authority to operate this
equipment.
COMPLIANCE NOTICE OF INDUSTRY CANADA
This Class B digital apparatus complies with Canadian ICES-003.
EN-5
EN-6
2
3
1
Preparing your projector
What’s included in the box
AC power cord
1 RGB cable for PC
Important:
The attached power cords are to be used exclusively for this product. Never use them for other products.•
for US J2552-0063-03
for EU J2552-0066-02
for UK J2552-0065-02
J2552-0072-03
1 Remote control
1 User Manual/Quick Start up (English only)
1 Safety Manual/Quick Start up
1 CD-ROM (with User Manual)
2 Battery
1 Lens cap
1 Lamp replacement attachment
Inserting the batteries into the remote control
1.
2.
3.
Important:
Remove the back lid of the remote control.
Check the polarity (+), (-) of the batteries, and set them
correctly, inserting their (-) side first.
•
If the battery is inserted from the (+) side first, inserting
the (-) side is difficult because the coil spring end hits
on the battery side. If the battery is forced in this way,
the outer label of the battery may get ripped and it may
cause a short-circuit and heating.
Attach the back lid.
Use two size-AA batteries (R6).
•
Replace the two batteries with new ones when the
•
remote control is slow to respond.
Removing the batteries from the remote control
Remove the back lid of the remote control and take out the batteries.
Caution:
Use of a battery of wrong type may cause explosion.
•
Only Carbon-Zinc or Alkaline-Manganese Dioxide type batteries should be used.
•
Dispose of used batteries according to your local regulations.
•
Batteries may explode if misused. Do not recharge, disassemble, or throw them in fire.
•
Be sure to handle the batteries according to the instructions.
•
Load the batteries with its positive (+) and negative (-) sides correctly oriented as indicated on the remote control.
•
Keep batteries out of reach of children and pets.
•
Remove the batteries, if the remote control is not used for a long time.
•
Do not combine a new battery with an old one.
•
If the solution of batteries comes in contact with your skin or clothes, rinse with water. If the solution comes in
•
contact with your eyes, rinse them with water and then consult your doctor.
Preparing your projector (continued)
10
8 5
1 23 4
9
10
8 5
1 23 4
9
767
6
HC3200
6 4 2
8 9 5 3 17
HC3200
6 4 2
8 9 5 3 17
5 6 1 2 3 4
7
5 6 1 2 3 4
7
Overview
FOCUS ring
1
ZOOM ring
2
Control panel
3
Air inlet grille
4
Remote control sensor (Front)
5
Air outlet grille
6
Terminal board
7
Adjustment feet
8
Lock bar
9
Lamp cover
10
Caution:
Do not replace the lamp immediately after using the projector
because the lamp would be extremely hot and it may cause burns.
Control panel
Terminal panel
Power button
1
POWER indicator
2
MENU button
3
STATUS indicator
4
ENTER button
5
AUTO POSITION / p button
6
HDMI / COMPUTER / t button
7
q button
8
VIDEO/ u button
9
Important:
While the menu or the screen for the keystone adjustment or
•
password entry is being displayed, the HDMI / COMPUTER,
VIDEO, and AUTO POSITION buttons function as the t, u,
and p buttons respectively.
VIDEO IN and S-VIDEO IN terminals
1
COMPONENT VIDEO IN terminals
2
COMPUTER IN/COMPONENT VIDEO IN terminal
3
(Mini D-SUB 15-pin)
HDMI IN terminal (HDMI 19-pin)
4
SERIAL terminal (Mini DIN 8-pin)
5
Used for projector control by computer. Contact your
•
dealer for details.
TRIGGER terminal
6
Used for the optional electric screen.
•
Power jack
7
EN-7
EN-8
Preparing your projector (continued)
15
16
14
12
11
13
18
19
20
17
1
2
3
4
5
6
7
8
9
10
15
16
14
12
11
13
18
19
20
17
1
2
3
4
5
6
7
8
9
10
Bottom side
Remote control
Adjustment feet
1
ON ( I ) button
1
COMPUTER button
2
HDMI button
3
COMPONENT button
4
AV MEMORY buttons
5
ENTER button
6
MENU button
7
CONTRAST button*
8
BRIGHTNESS button*
9
GAMMA button*
10
SHARPNESS button*
11
COLOR button*
12
COLOR TEMP. button*
13
COLOR MANAGEMENT button
14
p, q, t, u buttons
15
VIDEO button
16
S-VIDEO button
17
AUTO POSITION button
18
ASPECT button
19
OFF ( ) button
20
* : See below for the picture quality adjusting buttons.
Important:
When you press any button on the remote control, the buttons on the remote control are lit. Wait approx. 6 seconds
after releasing the button to turn them off.
Using the picture quality adjusting buttons
When you press any of the picture quality adjusting buttons, the screen for adjusting the picture quality appears. Adjust
the picture quality by pressing the t and u buttons. The picture quality adjustment can be made alternatively in the
IMAGE menu. (See page 26.) Items in the menus are shown in parentheses below.
CONTRAST (CONTRAST) ............... Adjusts the contrast of the projected image.
BRIGHTNESS (BRIGHTNESS) ....... Adjusts the brightness of the projected image.
COLOR TEMP. (COLOR TEMP.) ...... Selects one of the preset color temperatures. Adjustment of USER mode is also
available. (See page 32.)
GAMMA (GAMMA MODE) ............... Selects one of the preset gamma mode. Adjustment of USER mode is also
SHARPNESS (SHARPNESS) .......... Adjusts the sharpness of the projected image.
COLOR (COLOR) ............................. Adjusts the color thickness of the projected image.
available. (See page 33.)
Using the remote control
20°
10°
20°
10˚
20°
20°
30°30°
30°30°
30°30°
30°30°
Operational range of the remote control
Front of projector Rear of projector
Front of projector Rear of projector
Operate the remote control within a distance of
Operate the remote control within a distance of
10 m (30 feet) from the projector, pointing the IR
10 m (30 feet) from the projector, pointing the IR
beam at the remote control photo-sensor (front
beam at the remote control photo-sensor (front
or rear) of the projector.
or rear) of the projector.
•
•
•
•
Keep the remote control photo-sensor out of direct
sunlight or fluorescent lamp light.
Keep the remote control photo-sensor at least 2 m (6
feet) away from fluorescent lamps. Otherwise, the remote
control may malfunction.
If there is an inverter-operated fluorescent lamp near the
remote control, the remote control operation may become
unstable.
When you use the remote control too close to the remote
control sensor, the remote control may not work correctly.
Reception angle
Vertical directions
Vertical directions (ceiling mount)
When operating the remote control, keep the distance
from the remote control to the projector via the screen
within about 5 m (15 feet). The operable range of the
remote control, however, depends on the characteristics
of the screen.
EN-9
Setting up your projector
SW
Hd
SH
Center of the lens
(Width of the projected image)
Projection distance (L)
(Height of the
projected image)
Screen size
Setting up the screen
Install the screen perpendicularly to the projector. If the screen can not be installed in such a way, adjust the projection
angle of the projector. (See page 12.)
•
Install the screen and projector so that the projector’s lens is placed at the same height and horizontal position of
the screen center.
•
Do not install the screen where it is exposed to direct sunlight or lighting. Light directly reflecting on the screen
makes the projected images washed-out and hard to view.
SCREEN SIZE
You can keep the image display area within the screen by setting SCREEN SIZE in the ADVANCED MENU of IMAGE
menu according to the aspect ratio of the actual screen. Select 16:9 when the aspect ratio of the screen is 16:9 or 4:3,
and select CINEMA SCOPE (2.35:1) when the aspect ratio is 2.35:1 (CinemaScope).
When setting SCREEN SIZE to CINEMA SCOPE (2.35:1):
CinemaScope size movies are projected in the full screen.
•
Set ASPECT in the FEATURE menu to 16:9 when displaying Vista-size images. In this case, they are squeezed
•
horizontally.
When ASPECT in the FEATURE menu is set to AUTO and 480i/p, 576i/p, 720p, or 1080i/p signal is input, the part
•
for displaying subtitles is not projected. To display subtitles, reset SCREEN SIZE to 16:9 and adjust the image
position using VERTICAL LOCATION in the ADVANCED MENU of the IMAGE menu. (To display the menu on the
screen, adjust SHUTTER(U) in the SIGNAL - USER menu to position the menu.)
Screen size and projection distance
Refer to the following tables to determine the screen size and projection distance.
The figures in the tables are approximate and may be slightly different from the actual measurements.
•
When the aspect ratio of the screen is 16:9
Screen size Projection distance (L)
Diagonal size Height (SH) Width (SW) Shortest (Wide) Longest (Tele)
inch cm inch cm inch cm inch m inch m inch cm
50 127 25 62 44 111 59 1.5 89 2.3 8.2 21
60 152 29 75 52 133 71 1.8 107 2.7 9.9 25
70 178 34 87 61 155 84 2.1 125 3.2 11.5 29
80 203 39 100 70 177 96 2.4 144 3.6 13.2 34
90 229 44 112 78 199 108 2.7 162 4.1 14.8 38
100 254 49 125 87 221 120 3.1 180 4.6 16.5 42
110 279 54 137 96 244 133 3.4 198 5.0 18.1 46
120 305
150 381 74 187 131 332 182 4.6 271 6.9 24.7 63
200
250 635 123 311 218 553 304
300 762
Projection distance changes according to the setting of SCREEN SIZE in the ADVANCED MENU in the IMAGE menu. The table above is in the
•
case of “16:9.”
Depending on the installation conditions, warm air that is emitted from the exhaust vents may flow into the intake
•
vent, causing the projector to display “TEMPERATURE!!” and then stop projecting images.
59 149 105 266 145 3.7 216 5.5 19.8 50
508 98 249 174 443 243 6.2 362 9.2 33.0 84
147 374 261 664 365 9.3 - - 49.5 126
7.7 453 11.5 41.2 105
EN-10
Hd
Setting up your projector (continued)
SW (=W)
H
SH
BB
(Width of the projected image)
(Height of the screen)
(Height of the
projected image)
Screen size
Screen size and projection distance (continued)
When the aspect ratio of the screen is 4:3
When the aspect ratio of the screen is 4:3, the positional relation between the projected image and the screen is as
shown on the right. Refer to the following table for installation.
When the aspect ratio of the image is 16:9
Screen size (4:3)
Diagonal size Height (SH) Width (SW) Height (H) Width (W) Shortest (Wide) Longest (Tele)
inch cm inch cm inch cm inch cm inch cm inch cm inch m inch m inch cm
50 127 30 76 40 102 23 57 40 102 3.8 10 54 1.4 82 2.1 7.6 19
60 152 36 91 48 122 27 69 48 122 4.5 11 65 1.7 98 2.5 9.1 23
70 178 42 107 56 142 32 80 56 142 5.3 13 77 1.9 115 2.9 10.6 27
80 203 48 122 64 163 36 91 64 163 6.0 15 88 2.2 132 3.3 12.1 31
90 229 54 137 72 183 41 103 72 183 6.8 17 99 2.5 148 3.8 13.6 35
100 254 60 152 80 203 45 114 80 203 7.5 19 110 2.8 165 4.2 15.1 38
110 279 66 168 88 224 50 126 88 224 8.3 21 122 3.1 182 4.6 16.7 42
120 305 72 183
150 381 90 229 120 305 68 171 120 305 11.3 29 166 4.2 249 6.3 22.7 58
508 120 305 160 406 90 229 160 406 15.0 38 223 5.7 332 8.4 30.3 77
200
250 635
300 762
Projection distance changes according to the setting of SCREEN SIZE in the ADVANCED MENU in the IMAGE menu. The table above is in the
•
150 381 200 508 113 286 200 508 18.8 48 279 7.1 416 10.6 37.8 96
180 457 240 610 135 343 240 610 22.5 57 335 8.5 - - 45.4 115
96 244 54 137 96 244 9.0 23 133 3.4 199 5.0 18.2 46
Size of the projected image
(16:9)
Black space
(B)
Projection distance (L)
Hd
case of “16:9.”
When the aspect ratio of the screen is 2.35:1 (CinemaScope)
Screen size (2.35:1) Projection distance (L)
Diagonal size Height (SH) Width (SW) Shortest (Wide) Longest (Tele)
inch cm inch cm inch cm inch m inch m inch cm
100 254 39 99 92 234 127 3.2 190 4.8 23.7 60
110 279 43 109 101 257 140 3.6 209 5.3 26.1 66
120 305
130 330
140 356 55 139 129 327 179 4.5 267 6.8 33.2 84
150 381 59 149 138 351 192 4.9 286 7.3 35.6 90
160 406 63 159 147 374 205 5.2 305 7.8 38.0 96
170 432 66 169 156 397 218 5.5 325 8.2 40.4 103
180 457 70 179 166 421 231 5.9 344 8.7 42.7 109
190 483 74 189 175 444 244 6.2 363 9.2 45.1 115
200
Projection distance changes according to the setting of SCREEN SIZE in the ADVANCED MENU in the IMAGE menu. The table above is in the
•
47 119 110 281 153 3.9 229 5.8 28.5 72
51 129 120 304 166 4.2 248 6.3 30.9 78
508 78 199 184 468 256 6.5 382 9.7 47.5 121
case of “CINEMA SCOPE (2.35:1).”
Hd
EN-11
Setting up your projector (continued)
opt.
AV MEMORY 1
INSTALLATION
KEYSTONE 0
opt.
AV MEMORY 1
INSTALLATION
KEYSTONE 0
Correcting skewed or distorted image
For the best projection, project images on a flat screen installed at 90 degrees to
the floor. If necessary, tilt the projector using the two adjustment feet on the bottom
of the projector.
Tilt up the projector to the appropriate angle.
1.
Rotate the adjustment feet for fine adjustment.
2.
Screen
Screen
Adjustment feet
Adjustment feet
Important:
Don’t transport the projector with its adjustment feet extended. Otherwise the adjustment feet may be damaged.
When fine streaks are seen on projected images
This is due to interference with the screen surface and is not a malfunction. Replace the screen or displace the focus a
little. (See page 18 or 23 for focus adjustment.)
When projected images are distorted to a trapezoid
When the screen and the projector are not placed perpendicularly to each other, projected images become
trapezoidal. If you cannot make the projector and the screen perpendicular to each other by mechanical adjustments,
adjust keystone.
With the INSTALLATION menu:
(See page 26 for menu setting.)
Display the INSTALLATION menu.
1.
Select KEYSTONE by pressing the p or q button.
2.
Equalize the widths at the top and bottom of the screen by pressing the t
3.
or u button, viewing the screen.
To cancel the menu:
Press the MENU button several times.
4.
When the keystone adjustment is carried out, the adjustment value is indicated. Note that this value doesn’t mean a
•
Press the t
Press the t
button.
button.
Press the u
Press the u
button.
button.
projection angle.
The allowable range of the adjustment value in the keystone adjustment varies depending on the installation
•
condition, Input signal and aspect settings in MENU.
When the keystone adjustment takes effect, the resolution decreases. In addition, stripes may appear or straight
•
lines may bend in images with complicated patterns. They are not due to product malfunctions.
When the keystone adjustment is carried out, the image may not be displayed correctly because of the type of input
•
signal.
When the keystone adjustment is performed, the displayed image may be distorted.
•
Depending on the installation conditions of the projector and the screen, a perfect rectangular image and the proper
•
aspect ratio may not be obtained.
EN-12
Setting up your projector (continued)
Front projection, ceiling mounting
For ceiling mounting,
you need the ceiling
mount kit designed for
this projector. Ask a
specialist for installation.
For details, consult your
dealer.
The warranty on this projector does not cover any
•
damage caused by use of any non-recommended
ceiling mount kit or installation of the ceiling mount
kit in an improper location.
When using the projector mounted on the ceiling,
•
set IMAGE REVERSE in the INSTALLATION menu
to MIRROR INVERT. See page 27.
When the projector is mounted on the ceiling,
•
images may appear darker than those projected in
the case of tabletop mounting. This isn’t a product
malfunction.
Ask your installation specialist to provide an A/C
•
power switch. When you do not use the projector, be
sure to shut down the main power by the switch.
Do not install the projector where the exhaust vents
•
are exposed to air emitted by an air conditioning.
Such installation may cause a breakdown.
Do not install the projector near a fire alarm
•
because it emits hot air from its exhaust vents.
Important:
Do not apply force to the lens, because the lens may
•
be damaged.
Be sure to use this projector at an altitude of less than
•
1500 meters.
TRIGGER terminal
The TRIGGER terminal on the rear of the projector
is a terminal that outputs a 12 V signal to control an
externally connected device (electric screen) when
images are projected.
TRIGGER
To externally
connected device
Ring (NC)
(Ground 0 V)
Tip (12 V)
Rear projection
Ask a specialist for
installation. For details,
consult your dealer.
For rear projection,
•
set IMAGE
REVERSE in the
INSTALLATION
menu to MIRROR. See page 27.
Caution:
Placing the projector directly on a carpet impairs
•
ventilation by the fans, causing damage or failure.
Put a hard board under the projector to facilitate
ventilation.
Place the projector at least 50 cm (or 20 inch)
•
away from the wall to prevent the air inlet grille
and the air outlet grilles that emit hot air from
being blocked.
Do not use the projector in the following locations
•
and manners, which may cause fire or electric
shock.
In a dusty or humid place.
•
In a sideways position, or with the lens facing
•
down.
Near a heater.
•
In an oily, smoky, or damp place such as a kitchen.
•
In direct sunlight.
•
Where the temperature rises high, such as in
•
a closed car.
Where the temperature is lower than +41°F
•
(or +5°C) or higher than +95°F (or +35°C ).
To use the TRIGGER terminal, set TRIGGER OUT
to SCREEN or ANAMORPHIC in the INSTALLATION
menu. (The factory default is OFF. See page 27 for
details.) Use the following steps to change the setting.
With the INSTALLATION menu:
(See page 26 for menu setting.)
Display the INSTALLATION menu.
1.
Select TRIGGER OUT by pressing the p or q
2.
button.
Select SCREEN or ANAMORPHIC by pressing the
3.
t or u button.
To cancel the menu:
Press the MENU button.
4.
Caution:
Do not use the signal output from the TRIGGER
•
terminal as a power for other devices.
Do not link the TRIGGER terminal with an audio
•
terminal of other device because that device may be
damaged.
The rated current for the TRIGGER terminal is
•
200 mA. If you use a current exceeding this rating, a
failure may occur.
For information about electric screens, please
•
contact screen manufacturers.
EN-13
Viewing video images
A. Connecting the projector to video equipment
When the projector and the connected devices are located too close to each other, the projected image may be
•
affected by their interference.
See the owner’s guide of each device for details about its connections.
•
Preparation:
Make sure that the power of the projector and that of the video equipment are turned off.
•
Basic home theater system connection
EN-14
Video player
DVD player
Set-top box or digital tuner
Viewing video images (continued)
PB/CB
Y
PR/CR
PB/CB
PR/C
R
Y
1
2
1
2
1
2
1
2
Connecting to a video player, etc.
Video player, or the like
Video cable (option)
Video cable (option)
To VIDEO
To VIDEO
IN terminal
IN terminal
S-video cable (option)
S-video cable (option)
To S-VIDEO
To S-VIDEO
IN terminal
IN terminal
Video player, or the like
To video output
To video output
terminal
terminal
Video player, or the like
Video player, or the like
To S-video output
To S-video output
terminal
terminal
Connect one end of the optional video cable to the
1.
VIDEO IN terminal of the projector.
Connect the other end of the video cable to the video
2.
output terminal of the video equipment.
When the video equipment is equipped with the S-
video output terminal, make the connection as follows:
Connect one end of the optional S-video cable to the
1.
S-VIDEO IN terminal of the projector.
Connect the other end of the S-video cable to the S-
2.
video output terminal of the video equipment.
Also read the instruction manual of the equipment to be connected.
•
Contact your dealer for details of connection.
•
When a TV tuner or VCR is connected:
When you use this projector with a TV tuner or VCR connected, no image may appear or a message of NO SIGNAL
may appear on the screen when you change the channel via any channel that is not being received. In such a case,
set the channels of the TV tuner or VCR again. To avoid such symptom, use the TV tuner or VCR with its channel skip
function (that is a function not to display channels that are not being received) enabled.
Connecting to a DVD player or HDTV decoder
To connect this projector to video equipment that has component video output terminals, such as a DVD player, use
the COMPONENT VIDEO IN terminals.
Component cable (option)
DVD player or HDTV decoder
The terminal’s names Y, PB, and PR are given as examples of when a HDTV decoder is connected.
•
The terminal’s names vary depending on the connected devices.
•
Images may not be projected correctly depending on the type of the DVD player you use.
•
Though it may take some time before an image is displayed on the screen depending on the type of the input
•
signal, such symptom is not a malfunction.
When connecting a HDTV decoder having RGB output terminals, set COMPUTER INPUT to RGB in the SIGNAL
•
menu.
EN-15
Loading...