Mitsubishi Heavy Industries FDTVA151HEN1R, FDTCVA151HEN1R, FDTCVA201HEN1R, FDTCVA302HENP1R, FDTCVA402HENP2R Technical Manual

Manual No. '07·PAC-T-115

T E C H N I C A L M A N U A L

C o l l e c t i o n d a t a

PACKAGED AIR-CONDITIONER

MULTI-TYPE (V-MULTI) PACKAGED AIR-CONDITIONER

(Split system, Air to air heat pump type) CEILING RECESSED COMPACT TYPE

CEILING RECESSED TYPE

WALL MOUNTED TYPE

CEILING SUSPENDED TYPE

FDTCVA151HEN1R

201HEN1R

(OUTDOOR UNIT)

FDCVA302HENR

402HENAR 402HESAR 502HENAR 502HESAR 602HENAR 602HESAR 802HESAR

1002HESAR

FDTA151R

201R 251R 301R 401R 501R

(INDOOR UNIT)

FDTCA151R

201R

FDTCVA302HENP1R

402HENP2R 402HESP2R

FDTCVA602HENT2R

602HEST2R

FDTVA151HEN1R

201HEN1R 251HEN1R 302HEN1R 402HEN2R 402HES2R 502HEN2R 502HES2R 602HEN2R 602HES2R

FDTVA302HENP1R

402HENP2R 402HESP2R 502HENP2R 502HESP2R 602HENP2R 602HESP2R 802HESP2R

1002HESP2R

FDTVA602HENT2R

602HEST2R 802HEST2R

FDTVA802HESD2R

1002HESD2R

FDKNVA151HEN1R

201HEN1R 251HEN1R

FDKNVA302HENP1R

402HENP2R 402HESP2R 502HENP2R 502HESP2R

FDKNVA602HENT2R

602HEST2R

FDENVA151HEN1R

201HEN1R 251HEN1R 302HEN1R 402HEN2R 402HES2R 502HEN2R 502HES2R 602HEN2R 602HES2R

FDENVA302HENP1R

402HENP2R 402HESP2R 502HENP2R 502HESP2R 602HENP2R 602HESP2R 802HESP2R

1002HESP2R

FDENVA602HENT2R

602HEST2R 802HEST2R

SATELLITE DUCTED TYPE

FDUMVA201HEN2R

251HEN2R 302HEN2R 402HEN2R 402HES2R 502HEN2R 502HES2R 602HEN2R 602HES2R

FDUMVA402HENP2R

402HESP2R 502HENP2R 502HESP2R 602HENP2R 602HESP2R 802HESP2R

1002HESP2R

FDUMVA602HENT2R

602HEST2R 802HEST2R

FDENA151R

201R 251R 301R 401R 501R

FDKNA151R

201R 251R

FDUMA202R

252R 302R 402R 502R

HIGH STATIC PRESSURE DUCT TYPE

FDUVA802HES2R

1002HES2R

-

1

-

TABLE OF CONTENTS

1. PACKAGED AIR-CONDITIONER .................................................................................... 2

2. MULTI-TYPE (V MULTI) PACKAGED AIR-CONDITIONER ........................................ 291

3. WIRELESS KIT (OPTIONAL PARTS) ..........................................................................318

-

2

-

1. PACKAGED AIR-CONDITIONER

CONTENTS

1.1 GENERAL INFORMATION ...........................................................................................4

1.1.1 Speciﬁ c features ......................................................................................................4

1.1.2 How to read the model name ................................................................................... 4

1.2 SELECTION DATA ........................................................................................................ 5

1.2.1 Specifications .......................................................................................................... 5

(1) Ceiling recessed compact type (FDTC) ................................................................... 5

(2) Ceiling recessed type (FDT) .................................................................................. 12

(3) Ceiling suspended type (FDEN) ............................................................................36

(4) Satellite ducted type (FDUM) .................................................................................58

(5) High static pressure duct type (FDU) .....................................................................78

(6) Wall mounted type (FDKN) .................................................................................... 80

1.2.2 Range of usage & limitations ................................................................................. 90

1.2.3 Exterior dimensions ............................................................................................... 93

(1) Indoor unit .............................................................................................................. 93

(2) Remote controller (Optional parts) ......................................................................105

(3) Outdoor unit ......................................................................................................... 107

1.2.4 Inside view ........................................................................................................... 113

1.2.5 Exterior appearance ............................................................................................116

1.2.6 Piping system ......................................................................................................119

1.2.7 Selection chart ..................................................................................................... 126

1.2.8 Characteristics of fan ........................................................................................... 137

1.2.9 Noise level ........................................................................................................... 140

(1) Indoor unit ............................................................................................................ 140

(2) Outdoor unit ......................................................................................................... 143

1.3 ELECTRICAL DATA .................................................................................................. 144

1.3.1 Electrical wiring .................................................................................................... 144

(1) Indoor unit ............................................................................................................ 144

(2) Outdoor unit ......................................................................................................... 151

1.4 OUTLINE OF OPERATION CONTROL BY MICROCOMPUTER ............................. 156

(1) Remote controller ................................................................................................ 156

(2) Operation control function by the indoor controller .............................................. 158

(3) Operation control function by the wired remote controller ...................................165

-

3

-

(4) Operation control function by the outdoor controller ............................................ 166

♦ Models FDCVA151 ~ 251 ..................................................................................... 166

♦ Models FDCVA302 ~ 1002 ................................................................................... 172

1.5 APPLICATION DATA ................................................................................................ 184

1.5.1 Installation of indoor unit ...................................................................................... 185

(1) Ceiling recessed compact type (FDTC) ............................................................... 185

(2) Ceiling recessed type (FDT) ................................................................................ 190

(3) Ceiling suspended type (FDEN) .........................................................................196

(4) Wall mounted type (FDKN) .................................................................................. 200

(5) Satellite ducted type (FDUM) ...............................................................................203

(6) High static pressure duct type (FDU) ...................................................................209

1.5.2 Installation of wired remote controller .................................................................. 213

1.5.3 Installation of outdoor unit .................................................................................... 214

(1) Haulage and installation ...................................................................................... 214

(2) Refrigerant piping work ........................................................................................ 216

(3) Air tightness test and air purge ............................................................................ 222

(4) Refrigerant charge ............................................................................................... 223

(5) Drain piping work ................................................................................................. 224

(6) Electrical wiring .................................................................................................... 224

(7) Setting functions using the wired remote controller ............................................. 227

(8) Checking operation data ...................................................................................... 232

(9) Test run ................................................................................................................ 233

1.6 MAINTENANCE DATA .............................................................................................. 236

1.6.1 Servicing ............................................................................................................. 236

1.6.2 Trouble shooting for refrigerant circuit .................................................................. 237

1.6.3 Diagnosing of microcomputer circuit .................................................................... 238

(1) Selfdiagnosis function .......................................................................................... 238

(2) Procedures of trouble diagnosis ..........................................................................241

(3) Error diagnosis procedures at the indoor unit side ..............................................241

(4) Error diagnosis procedures at the outdoor unit side ............................................ 259

(5) Inspection procedure for the failure which doesn’t have an error code ................ 288

(6) Check anomalous operation data with the wired remote controller ..................... 289

1.6.4 Check display on wireless speciﬁ cation models (FDEN · FDKN· FDT) ............... 290

-

4

-

RoHS specification

: Single type

(blank)

P: Twin type T: Triple type D: Double twin type

Applicable power source ... See the specifications Heat pump type Series No. Product capacity R410A models Inverter specification Model name

Example: FDT V A 25 1 H EN P 1 R

1.1 GENERAL INFORMATION

1.1.1 Speciﬁ c features

(1) All models employ R410A, with RoHS compliance. (2) Industry leading COP. Thanks to achievement of the highest COP level in the industry, the energy consumption has been cut by 24~38% compared with

our former models (constant speed models). (3) Energy labeling “Class A” MHI models have cleared the class A standard, the highest energy saving level, with their high COP (coefﬁ cient of performance). (4) The microcomputer chip is installed in the indoor unit and outdoor unit. There is no need for the unit to communicate between the

outdoor and indoor units so the unit is more resistant to electromagnetic noise thus the incidence of microcomputer malfunction

has been reduced. The compressor in the outdoor unit has its own self protection function, that reacts according to abnormal high

pressure and excessive high temperature. (5) There are only three power lines between the outdoor and indoor unit. One cabtyre cable with 3 wires encased in one sheath is

enough for conducting the wiring work between the outdoor unit and the indoor unit. This contributes to simpler wiring work in

the ﬁ eld. (6) All air supply ports have auto swing louvers. (Only case of FDTC, FDT, FDEN and FDKN models). The indoor fan motor has

three speeds of high, medium and low. (7) All models have service valves protruding from the outdoor unit for faster ﬂ are connection (FDCVA802, 1002: Only a gas side is

brazing) work in the field. (8) The size and weight of the outdoor units in the FDCVA 151~251,302 Series have been greatly reduced. Use of an inverter has also

improved energy conservation and economy. (9) Compared to the previous models, a single fan is used in the FDCVA402~602 outdoor unit models and forward blowing is used

in the FDCVA802 and FDCVA1002 models,resulting in markedly reduced weight and greater compactness.In addition, use of an

inverter makes these units much more economical compared to the previous ﬁ xed speed units. (10) Realization of signiﬁ cant reduction in size and weight compared with our former models, applying front blow outlet on all models.

Reductions are 50% in weight of 6HP, 72% in volume of 8HP and 63% in the foot print of 8HP.

1.1.2 How to read the model name

FDTC : FDT :

FDEN : FDUM: FDU : FDKN : FDC :

Ceiling recessed compact type unit Ceiling recessed type unit

Ceiling suspended type unit Satellite ducted type unit High static pressure duct type unit Wall mounted type unit Outdoor unit

-

5

-

1.2 SELECTION DATA

1.2.1 Specifications

(1) Ceiling recessed compact type (FDTC)

(a) Single type

Model FDTCVA151HEN1R

Model

Item

FDTCVA151HEN1R

FDTCA151R FDCVA151HENR

Nominal cooling capacity

(1)

kW

4.0 [1.8~4.7]

Nominal heating capacity

(1)

kW

4.5 [2.0~5.4]

Power source 1 Phase, 220-240V 50Hz/220V 60Hz

Operation data

(3)

Cooling power consumption kW

1.22/1.22

Running current (Cooling) A

5.4/5.6

Power factor (Cooling) %

98/99

Heating power consumption kW

1.32/1.32

Running current (Heating) A

5.9/6.2

Power factor (Heating) %

97/97

Inrush current (L.R.A) A

5

Noise level dB(A)

Powerful mode Hi:46 Me:42 Lo:38

Mild mode Hi:42 Me:38 Lo:35

48

Exterior dimensions Height × Width × Depth

mm

Unit 248 × 570 × 570 Panel 35 × 700 × 700

595 × 780 (+67) × 290

Net weight kg 19.5 (Unit:16 Panel:3.5) 40 Refrigerant equipment

Compressor type & Q’ty

–

5CS102XFD × 1

Starting method – Direct line start

Heat exchanger

Louver fin & inner grooved tubing Straight fin & inner grooved tubing

Refrigerant control – Electronic expansion valve

Refrigerant R410A

Quantity kg –

1.55 [Pre-charged up to the piping length of 30m]

Refrigerant oil

r

–

0.48 (RB68A)

Defrost control Microcomputer controlled de-icer

Air handling equipment

Fan type & Q’ty

Turbo fan × 1 Propeller fan × 1

Motor W 50 × 134 × 1 Starting method Direct line start Direct line start

Air ﬂ ow CMM

Powerful mode Hi:13.5 Me:11.5 Lo:10

Mild mode Hi:11.5 Me:10 Lo:8

41

Outside air intake

Impossibility – Air filter, Q’ty Plastic net (washable) × 1 – Shock & vibration absorber Rubber sleeve (for fan motor) Rubber mount (for compressor) Electric heater W – 20 (Crank case heater)

Operation control

Operation switch

Wired remote control switch (Optional : RC-E1R)

Wireless kit (Optional : RCND-KIT-HER)

– (Indoor unit side)

Room temperature control Thermostat by electronics –

Safety equipment

Internal thermostat for fan motor.

Frost protection thermostat.

Internal thermostat for fan motor.

Anomalous discharge temperature protection.

Installation data Refrigerant piping size

mm

(in)

Liquid line: φ6.35 (1/4″) Gas line: φ12.7 (1/2″)

Connecting method Flare piping

Drain hose

Connectable with VP25 (I.D. 25mm, O.D. 32mm) – Insulation for piping Necessary (both Liquid & Gas lines) Accessories Mounting kit. Drain hose Optional parts Decorative Panel (TC-PSA-24W-ER)

Notes (1) The data are measured at the following conditions.

Item

Operation

Indoor air temperature Outdoor air temperature

Standards

DB WB DB WB

Cooling 27˚C 19˚C 35˚C 24˚C

ISO-T1

Heating 20˚C – 7˚C 6˚C

(2) This packaged air-conditioner is manufactured and tested in conformity with the following standard. ISO-T1 “UNITARY AIR-CONDITIONERS” (3) The operation data indicate when the air-conditioner is operated at 230V 50Hz or 220V 60Hz. (4) Values in [ ~ ] show the minimum to maximum range.

-

6

-

Model FDTCVA201HEN1R

Model

Item

FDTCVA201HEN1R

FDTCA201R FDCVA201HENR

Nominal cooling capacity

(1)

kW

5.0 [2.2~5.6]

Nominal heating capacity

(1)

kW

5.4 [2.5~6.3]

Power source 1 Phase, 220-240V 50Hz/220V 60Hz

Operation data

(3)

Cooling power consumption kW

1.62 /1.62

Running current (Cooling) A

7.1/7.5

Power factor (Cooling) %

99/98

Heating power consumption kW

1.53/1.53

Running current (Heating) A

6.7/7.0

Power factor (Heating) %

99/99

Inrush current (L.R.A) A

5

Noise level dB(A)

Powerful mode Hi:46 Me:42 Lo:38

Mild mode Hi:42 Me:38 Lo:35

48

Exterior dimensions Height × Width × Depth

mm

Unit 248 × 570 × 570

Panel 35 × 700 × 700

595 × 780 (+67) × 290

Net weight kg 19.5 (Unit:16 Panel:3.5) 40 Refrigerant equipment

Compressor type & Q’ty

–

5CS102XFD × 1

Starting method – Direct line start

Heat exchanger

Louver fin & inner grooved tubing Straight fin & inner grooved tubing

Refrigerant control – Electronic expansion valve

Refrigerant R410A

Quantity kg –

1.55 [Pre-charged up to the piping length of 30m]

Refrigerant oil

r

–

0.48 (RB68A)

Defrost control Microcomputer controlled de-icer

Air handling equipment

Fan type & Q’ty

Turbo fan × 1 Propeller fan × 1

Motor W 50 × 134 × 1 Starting method Direct line start Direct line start

Air ﬂ ow CMM

Powerful mode Hi:13.5 Me:11.5 Lo:10

Mild mode Hi:11.5 Me:10 Lo:8

41

Outside air intake

Impossibility – Air filter, Q’ty Plastic net (washable) × 1 – Shock & vibration absorber Rubber sleeve (for fan motor) Rubber mount (for compressor) Electric heater W – 20 (Crank case heater)

Operation control

Operation switch

Wired remote control switch (Optional : RC-E1R)

Wireless kit (Optional : RCND-KIT-HER)

– (Indoor unit side)

Room temperature control Thermostat by electronics –

Safety equipment

Internal thermostat for fan motor.

Frost protection thermostat.

Internal thermostat for fan motor.

Anomalous discharge temperature protection.

Installation data Refrigerant piping size

mm

(in)

Liquid line: φ6.35 (1/4″) Gas line: φ12.7 (1/2″)

Connecting method Flare piping

Drain hose

Connectable with VP25 (I.D. 25mm, O.D. 32mm) – Insulation for piping Necessary (both Liquid & Gas lines) Accessories Mounting kit. Drain hose Optional parts Decorative Panel (TC-PSA-24W-ER)

Notes (1) The data are measured at the following conditions.

Item

Operation

Indoor air temperature Outdoor air temperature

Standards

DB WB DB WB

Cooling 27˚C 19˚C 35˚C 24˚C

ISO-T1

Heating 20˚C – 7˚C 6˚C

(2) This packaged air-conditioner is manufactured and tested in conformity with the following standard. ISO-T1 “UNITARY AIR-CONDITIONERS” (3) The operation data indicate when the air-conditioner is operated at 230V 50Hz or 220V 60Hz. (4) Values in [ ~ ] show the minimum to maximum range.

-

7

-

(b) Twin type

Model FDTCVA302HENP1R (Indoor unit: 2 units, Outdoor unit: 1 unit)

Model

Item

FDTCVA302HENP1R

FDTCA151R FDCVA302HENR

Nominal cooling capacity

(1)

kW

7.1[3.9~8.0]

Nominal heating capacity

(1)

kW

8.0[4.0~9.0]

Power source 1 Phase, 220-240V 50Hz/220V 60Hz

Operation data

(3)

Cooling power consumption kW

1.91/1.91

Running current (Cooling) A

8.3/8.8

Power factor (Cooling) %

99/99

Heating power consumption kW

2.08/2.08

Running current (Heating) A

9.0/9.6

Power factor (Heating) %

99/98

Inrush current (L.R.A) A

5

Noise level dB(A)

Powerful mode Hi:46 Me:42 Lo:38

Mild mode Hi:42 Me:38 Lo:35

48

Exterior dimensions Height × Width × Depth

mm

Unit 248 × 570 × 570 Panel 35 × 700 × 700

750 × 880 (+88) × 340

Net weight kg 19.5 (Unit:16 Panel:3.5) 60 Refrigerant equipment

Compressor type & Q’ty

–

2YC45DXD × 1

Starting method – Direct line start

Heat exchanger

Louver fin & inner grooved tubing Straight fin & inner grooved tubing

Refrigerant control – Electronic expansion valve

Refrigerant R410A

Quantity kg –

2.95 [Pre-charged up to the piping length of 30m]

Refrigerant oil

r

–

0.65 (FVC50K)

Defrost control Microcomputer controlled de-icer

Air handling equipment

Fan type & Q’ty

Turbo fan × 1 Propeller fan × 1

Motor W 50 × 1120 × 1 Starting method Direct line start

Air ﬂ ow CMM

Powerful mode Hi:13.5 Me:11.5 Lo:10

Mild mode Hi:11.5 Me:10 Lo:8

Cooling:60 Heating:48.5

Outside air intake

Available – Air filter, Q’ty Plastic net (washable) × 1 – Shock & vibration absorber Rubber sleeve (for fan motor) Rubber mount (for compressor) Electric heater W – 20 (Crank case heater)

Operation control

Operation switch

Wired remote control switch (Optional : RC-E1R)

Wireless kit (Optional : RCND-KIT-HER)

– (Indoor unit side)

Room temperature control Thermostat by electronics –

Safety equipment

Internal thermostat for fan motor.

Frost protection thermostat.

Internal thermostat for fan motor.

Anomalous discharge temperature protection.

Installation data Refrigerant piping size

Liquid line

mm

(in)

Indoor branch pipe, Outdoor main pipe: φ9.52 (3/8″)

Gas line Indoor branch pipe: φ12.7 (1/2″), Outdoor main pipe: φ15.88 (5/8″)

Connecting method Flare piping

Drain hose

Connectable with VP25 (I.D. 25mm, O.D. 32mm) – Insulation for piping Necessary (both Liquid & Gas lines) Accessories Mounting kit. Drain hose Optional parts Decorative Panel (TC-PSA-24W-ER)

Notes (1) The data are measured at the following conditions.

Item

Operation

Indoor air temperature Outdoor air temperature

Standards

DB WB DB WB

Cooling 27˚C 19˚C 35˚C 24˚C

ISO-T1

Heating 20˚C – 7˚C 6˚C

(2) This packaged air-conditioner is manufactured and tested in conformity with the following standard. ISO-T1 “UNITARY AIR-CONDITIONERS” (3) The operation data indicate when the air-conditioner is operated at 230V 50Hz or 220V 60Hz. (4) Values in [ ~ ] show the minimum to maximum range. (5) Indoor unit specifications show the specifications for one unit. Capacity and running characteristics values are shown for the case where two indoor

units are combined and run together.

-

8

-

Model FDTCVA402HENP2R (Indoor unit: 2 units, Outdoor unit: 1 unit)

Model

Item

FDTCVA402HENP2R

FDTCA201R FDCVA402HENAR

Nominal cooling capacity

(1)

kW

10.0 [6.1~11.2]

Nominal heating capacity

(1)

kW

11.2 [5.6~12.5]

Power source 1 Phase, 220-240V 50Hz/220V 60Hz

Operation data

(3)

Cooling power consumption kW

2.84/2.84

Running current (Cooling) A

12.4/13.0

Power factor (Cooling) %

99/99

Heating power consumption kW

3.08/3.08

Running current (Heating) A

13.5/14.1

Power factor (Heating) %

99/99

Inrush current (L.R.A) A

5

Noise level dB(A)

Powerful mode Hi:46 Me:42 Lo:38

Mild mode Hi:42 Me:38 Lo:35

50

Exterior dimensions Height × Width × Depth

mm

Unit 248 × 570 × 570 Panel 35 × 700 × 700

845 × 970 × 370

Net weight kg 19.5 (Unit:16 Panel:3.5) 74 Refrigerant equipment

Compressor type & Q’ty

–

RM-B5125MDE21 × 1

Starting method – Direct line start

Heat exchanger

Louver fin & inner grooved tubing Straight fin & inner grooved tubing

Refrigerant control – Electronic expansion valve

Refrigerant R410A

Quantity kg –

3.8 [Pre-charged up to the piping length of 30m]

Refrigerant oil

r

–

0.7 (M-MA68)

Defrost control Microcomputer controlled de-icer

Air handling equipment

Fan type & Q’ty

Turbo fan × 1 Propeller fan × 1

Motor W 50 × 1120 × 1 Starting method Direct line start Direct line start

Air ﬂ ow CMM

Powerful mode Hi:13.5 Me:11.5 Lo:10

Mild mode Hi:11.5 Me:10 Lo:8

Cooling:75, Heating:73

Outside air intake

Available – Air filter, Q’ty Plastic net (washable) × 1 – Shock & vibration absorber Rubber sleeve (for fan motor) Rubber mount (for compressor) Electric heater W – 20 (Crank case heater)

Operation control

Operation switch

Wired remote control switch (Optional : RC-E1R)

Wireless kit (Optional : RCND-KIT-HER)

– (Indoor unit side)

Room temperature control Thermostat by electronics –

Safety equipment

Internal thermostat for fan motor.

Frost protection thermostat.

Internal thermostat for fan motor.

Anomalous discharge temperature protection.

Installation data Refrigerant piping size

Liquid line

mm

(in)

Indoor branch pipe, Outdoor main pipe: φ9.52 (3/8″)

Gas line Indoor branch pipe: φ12.7 (1/2″), Outdoor main pipe: φ15.88 (5/8″)

Connecting method Flare piping

Drain hose

Connectable with VP25 (I.D. 25mm, O.D. 32mm) – Insulation for piping Necessary (both Liquid & Gas lines) Accessories Mounting kit. Drain hose Optional parts Decorative Panel (TC-PSA-24W-ER)

Notes (1) The data are measured at the following conditions.

Item

Operation

Indoor air temperature Outdoor air temperature

Standards

DB WB DB WB

Cooling 27˚C 19˚C 35˚C 24˚C

ISO-T1

Heating 20˚C – 7˚C 6˚C

(2) This packaged air-conditioner is manufactured and tested in conformity with the following standard. ISO-T1 “UNITARY AIR-CONDITIONERS” (3) The operation data indicate when the air-conditioner is operated at 230V 50Hz or 220V 60Hz. (4) Values in [ ~ ] show the minimum to maximum range. (5) Indoor unit specifications show the specifications for one unit. Capacity and running characteristics values are shown for the case where two indoor

units are combined and run together.

-

9

-

Model FDTCVA402HESP2R (Indoor unit: 2 units, Outdoor unit: 1 unit)

Model

Item

FDTCVA402HESP2R

FDTCA201R FDCVA402HESAR

Nominal cooling capacity

(1)

kW

10.0 [6.1~11.2]

Nominal heating capacity

(1)

kW

11.2 [5.6~12.5]

Power source 3 Phase, 380-415V 50Hz/380V 60Hz

Operation data

(3)

Cooling power consumption kW

2.84/2.84

Running current (Cooling) A

4.2/4.4

Power factor (Cooling) %

98/98

Heating power consumption kW

3.08/3.08

Running current (Heating) A

4.5/4.8

Power factor (Heating) %

99/97

Inrush current (L.R.A) A

5

Noise level dB(A)

Powerful mode Hi:46 Me:42 Lo:38

Mild mode Hi:42 Me:38 Lo:35

50

Exterior dimensions Height × Width × Depth

mm

Unit 248 × 570 × 570 Panel 35 × 700 × 700

845 × 970 × 370

Net weight kg 19.5 (Unit:16 Panel:3.5) 74 Refrigerant equipment

Compressor type & Q’ty

–

RM-B5125MDE31 × 1

Starting method – Direct line start

Heat exchanger

Louver fin & inner grooved tubing Straight fin & inner grooved tubing

Refrigerant control – Electronic expansion valve

Refrigerant R410A

Quantity kg –

3.8 [Pre-charged up to the piping length of 30m]

Refrigerant oil

r

–

0.7 (M-MA68)

Defrost control Microcomputer controlled de-icer

Air handling equipment

Fan type & Q’ty

Turbo fan × 1 Propeller fan × 1

Motor W 50 × 1120 × 1 Starting method Direct line start Direct line start

Air ﬂ ow CMM

Powerful mode Hi:13.5 Me:11.5 Lo:10

Mild mode Hi:11.5 Me:10 Lo:8

Cooling:75, Heating:73

Outside air intake

Available – Air filter, Q’ty Plastic net (washable) × 1 – Shock & vibration absorber Rubber sleeve (for fan motor) Rubber mount (for compressor) Electric heater W – 20 (Crank case heater)

Operation control

Operation switch

Wired remote control switch (Optional : RC-E1R)

Wireless kit (Optional : RCND-KIT-HER)

– (Indoor unit side)

Room temperature control Thermostat by electronics –

Safety equipment

Internal thermostat for fan motor.

Frost protection thermostat.

Internal thermostat for fan motor.

Anomalous discharge temperature protection.

Installation data Refrigerant piping size

Liquid line

mm

(in)

Indoor branch pipe, Outdoor main pipe: φ9.52 (3/8″)

Gas line Indoor branch pipe: φ12.7 (1/2″), Outdoor main pipe: φ15.88 (5/8″)

Connecting method Flare piping

Drain hose

Connectable with VP25 (I.D. 25mm, O.D. 32mm) – Insulation for piping Necessary (both Liquid & Gas lines) Accessories Mounting kit. Drain hose Optional parts Decorative Panel (TC-PSA-24W-ER)

Notes (1) The data are measured at the following conditions.

Item

Operation

Indoor air temperature Outdoor air temperature

Standards

DB WB DB WB

Cooling 27˚C 19˚C 35˚C 24˚C

ISO-T1

Heating 20˚C – 7˚C 6˚C

(2) This packaged air-conditioner is manufactured and tested in conformity with the following standard. ISO-T1 “UNITARY AIR-CONDITIONERS” (3) The operation data indicate when the air-conditioner is operated at 400V 50Hz or 380V 60Hz. (4) Values in [ ~ ] show the minimum to maximum range. (5) Indoor unit specifications show the specifications for one unit. Capacity and running characteristics values are shown for the case where two indoor

units are combined and run together.

-

10

-

(c) Triple type

Model FDTCVA602HENT2R (Indoor unit: 3 units, Outdoor unit: 1 unit)

Model

Item

FDTCVA602HENT2R

FDTCA201R FDCVA602HENAR

Nominal cooling capacity

(1)

kW

14.0 [6.7~14.8]

Nominal heating capacity

(1)

kW

16.0 [6.3~16.8]

Power source 1 Phase, 220-240V 50Hz/220V 60Hz

Operation data

(3)

Cooling power consumption kW

4.64/4.64

Running current (Cooling) A

20.4/21.3

Power factor (Cooling) %

99/99

Heating power consumption kW

4.52/4.52

Running current (Heating) A

20.0/20.9

Power factor (Heating) %

98/98

Inrush current (L.R.A) A

5

Noise level dB(A)

Powerful mode Hi:46 Me:42 Lo:38

Mild mode Hi:42 Me:38 Lo:35

53

Exterior dimensions Height × Width × Depth

mm

Unit 248 × 570 × 570 Panel 35 × 700 × 700

845 × 970 × 370

Net weight kg 19.5 (Unit:16 Panel:3.5) 74 Refrigerant equipment

Compressor type & Q’ty

–

RM-B5125MD11 × 1

Starting method – Direct line start

Heat exchanger

Louver fin & inner grooved tubing Straight fin & inner grooved tubing

Refrigerant control – Electronic expansion valve

Refrigerant R410A

Quantity kg –

3.8 [Pre-charged up to the piping length of 30m]

Refrigerant oil

r

–

0.7 (M-MA68)

Defrost control Microcomputer controlled de-icer

Air handling equipment

Fan type & Q’ty

Turbo fan × 1 Propeller fan × 1

Motor W 50 × 1120 × 1 Starting method Direct line start Direct line start

Air ﬂ ow CMM

Powerful mode Hi:13.5 Me:11.5 Lo:10

Mild mode Hi:11.5 Me:10 Lo:8

Cooling:75, Heating:73

Outside air intake

Available – Air filter, Q’ty Plastic net (washable) × 1 – Shock & vibration absorber Rubber sleeve (for fan motor) Rubber mount (for compressor) Electric heater W – 20 (Crank case heater)

Operation control

Operation switch

Wired remote control switch (Optional : RC-E1R)

Wireless kit (Optional : RCND-KIT-HER)

– (Indoor unit side)

Room temperature control Thermostat by electronics –

Safety equipment

Internal thermostat for fan motor.

Frost protection thermostat.

Internal thermostat for fan motor.

Anomalous discharge temperature protection.

Installation data Refrigerant piping size

Liquid line

mm

(in)

Indoor branch pipe, Outdoor main pipe: φ9.52 (3/8″)

Gas line Indoor branch pipe: φ12.7 (1/2″), Outdoor main pipe: φ15.88 (5/8″)

Connecting method Flare piping

Drain hose

Connectable with VP25 (I.D. 25mm, O.D. 32mm) – Insulation for piping Necessary (both Liquid & Gas lines) Accessories Mounting kit. Drain hose Optional parts Decorative Panel (TC-PSA-24W-ER)

Notes (1) The data are measured at the following conditions.

Item

Operation

Indoor air temperature Outdoor air temperature

Standards

DB WB DB WB

Cooling 27˚C 19˚C 35˚C 24˚C

ISO-T1

Heating 20˚C – 7˚C 6˚C

(2) This packaged air-conditioner is manufactured and tested in conformity with the following standard. ISO-T1 “UNITARY AIR-CONDITIONERS” (3) The operation data indicate when the air-conditioner is operated at 230V 50Hz or 220V 60Hz. (4) Values in [ ~ ] show the minimum to maximum range. (5) Indoor unit specifications show the specifications for one unit. Capacity and running characteristics values are shown for the case where three indoor

units are combined and run together.

-

11

-

Model FDTCVA602HEST2R (Indoor unit: 3 units, Outdoor unit: 1 unit)

Model

Item

FDTCVA602HEST2R

FDTCA201R FDCVA602HESAR

Nominal cooling capacity

(1)

kW

14.0 [6.7~14.8]

Nominal heating capacity

(1)

kW

16.0 [6.3~16.8]

Power source 3 Phase, 380-415V 50Hz/380V 60Hz

Operation data

(3)

Cooling power consumption kW

4.64/4.64

Running current (Cooling) A

6.8/7.1

Power factor (Cooling) %

98/99

Heating power consumption kW

4.52/4.52

Running current (Heating) A

6.6/7.0

Power factor (Heating) %

99/98

Inrush current (L.R.A) A

5

Noise level dB(A)

Powerful mode Hi:46 Me:42 Lo:38

Mild mode Hi:42 Me:38 Lo:35

53

Exterior dimensions Height × Width × Depth

mm

Unit 248 × 570 × 570 Panel 35 × 700 × 700

845 × 970 × 370

Net weight kg 19.5 (Unit:16 Panel:3.5) 74 Refrigerant equipment

Compressor type & Q’ty

–

RM-B5125MDE31 × 1

Starting method – Direct line start

Heat exchanger

Louver fin & inner grooved tubing Straight fin & inner grooved tubing

Refrigerant control – Electronic expansion valve

Refrigerant R410A

Quantity kg –

3.8 [Pre-charged up to the piping length of 30m]

Refrigerant oil

r

–

0.7 (M-MA68)

Defrost control Microcomputer controlled de-icer

Air handling equipment

Fan type & Q’ty

Turbo fan × 1 Propeller fan × 1

Motor W 50 × 1120 × 1 Starting method Direct line start Direct line start

Air ﬂ ow CMM

Powerful mode Hi:13.5 Me:11.5 Lo:10

Mild mode Hi:11.5 Me:10 Lo:8

Cooling:75, Heating:73

Outside air intake

Available – Air filter, Q’ty Plastic net (washable) × 1 – Shock & vibration absorber Rubber sleeve (for fan motor) Rubber mount (for compressor) Electric heater W – 20 (Crank case heater)

Operation control

Operation switch

Wired remote control switch (Optional : RC-E1R)

Wireless kit (Optional : RCND-KIT-HER)

– (Indoor unit side)

Room temperature control Thermostat by electronics –

Safety equipment

Internal thermostat for fan motor.

Frost protection thermostat.

Internal thermostat for fan motor.

Anomalous discharge temperature protection.

Installation data Refrigerant piping size

Liquid line

mm

(in)

Indoor branch pipe, Outdoor main pipe: φ9.52 (3/8″)

Gas line Indoor branch pipe: φ12.7 (1/2″), Outdoor main pipe: φ15.88 (5/8″)

Connecting method Flare piping

Drain hose

Connectable with VP25 (I.D. 25mm, O.D. 32mm) – Insulation for piping Necessary (both Liquid & Gas lines) Accessories Mounting kit. Drain hose Optional parts Decorative Panel (TC-PSA-24W-ER)

Notes (1) The data are measured at the following conditions.

Item

Operation

Indoor air temperature Outdoor air temperature

Standards

DB WB DB WB

Cooling 27˚C 19˚C 35˚C 24˚C

ISO-T1

Heating 20˚C – 7˚C 6˚C

(2) This packaged air-conditioner is manufactured and tested in conformity with the following standard. ISO-T1 “UNITARY AIR-CONDITIONERS” (3) The operation data indicate when the air-conditioner is operated at 400V 50Hz or 380V 60Hz. (4) Values in [ ~ ] show the minimum to maximum range. (5) Indoor unit specifications show the specifications for one unit. Capacity and running characteristics values are shown for the case where three indoor

units are combined and run together.

-

12

-

(2) Ceiling recessed type (FDT)

(a) Single type

Model FDTVA151HEN1R

Model

Item

FDTVA151HEN1R

FDTA151R FDCVA151HENR

Nominal cooling capacity

(1)

kW

4.0 [1.8~4.7]

Nominal heating capacity

(1)

kW

4.5 [2.0~5.4]

Power source 1 Phase, 220-240V 50Hz/220V 60Hz

Operation data

(3)

Cooling power consumption kW

1.22/1.23

Running current (Cooling) A

5.4/5.7

Power factor (Cooling) %

98/98

Heating power consumption kW

1.32/1.32

Running current (Heating) A

5.9/6.2

Power factor (Heating) %

97/97

Inrush current (L.R.A) A

5

Noise level dB(A)

Powerful mode Hi:36 Me:33 Lo:32

Mild mode Hi:33 Me:32 Lo:31

48

Exterior dimensions Height × Width × Depth

mm

Unit 270 × 840 × 840 Panel 35 × 950 × 950

595 × 780 (+67) × 290

Net weight kg 31 (Unit:24 Panel:7) 40 Refrigerant equipment

Compressor type & Q’ty

–

5CS102XFD × 1

Starting method – Direct line start

Heat exchanger

Louver fin & inner grooved tubing Straight fin & inner grooved tubing

Refrigerant control – Electronic expansion valve

Refrigerant R410A

Quantity kg –

1.55 [Pre-charged up to the piping length of 30m]

Refrigerant oil

r

–

0.48 (RB68A)

Defrost control Microcomputer controlled de-icer

Air handling equipment

Fan type & Q’ty

Turbo fan × 1 Propeller fan × 1

Motor W 14 × 134 × 1 Starting method Direct line start Direct line start

Air ﬂ ow CMM

Powerful mode Hi:18 Me:15 Lo:14

Mild mode Hi:15 Me:14 Lo:13

41

Outside air intake

Available – Air filter, Q’ty Plastic net (washable) × 1 – Shock & vibration absorber Rubber sleeve (for fan motor) Rubber mount (for compressor) Electric heater W – 20 (Crank case heater)

Operation control

Operation switch

Wired remote control switch (Optional : RC-E1R)

Wireless kit (Optional : RCN-T-35W-ER)

– (Indoor unit side)

Room temperature control Thermostat by electronics –

Safety equipment

Internal thermostat for fan motor.

Frost protection thermostat.

Internal thermostat for fan motor.

Anomalous discharge temperature protection.

Installation data Refrigerant piping size

mm

(in)

Liquid line: φ6.35 (1/4″) Gas line: φ12.7 (1/2″)

Connecting method Flare piping

Drain hose

Connectable with VP25 (I.D. 25mm, O.D. 32mm) – Insulation for piping Necessary (both Liquid & Gas lines) Accessories Mounting kit. Drain hose Optional parts Decorative Panel (T-PSA-35W-ER)

Notes (1) The data are measured at the following conditions.

Item

Operation

Indoor air temperature Outdoor air temperature

Standards

DB WB DB WB

Cooling 27˚C 19˚C 35˚C 24˚C

ISO-T1

Heating 20˚C – 7˚C 6˚C

(2) This packaged air-conditioner is manufactured and tested in conformity with the following standard. ISO-T1 “UNITARY AIR-CONDITIONERS” (3) The operation data indicate when the air-conditioner is operated at 230V 50Hz or 220V 60Hz. (4) Values in [ ~ ] show the minimum to maximum range.

-

13

-

Model FDTVA201HEN1R

Model

Item

FDTVA201HEN1R

FDTA201R FDCVA201HENR

Nominal cooling capacity

(1)

kW

5.0 [2.2~5.6]

Nominal heating capacity

(1)

kW

5.4 [2.5~6.3]

Power source 1 Phase, 220-240V 50Hz/220V 60Hz

Operation data

(3)

Cooling power consumption kW

1.42/1.43

Running current (Cooling) A

6.3/6.6

Power factor (Cooling) %

98/98

Heating power consumption kW

1.49/1.49

Running current (Heating) A

6.6/6.9

Power factor (Heating) %

98/98

Inrush current (L.R.A) A

5

Noise level dB(A)

Powerful mode Hi:36 Me:33 Lo:32

Mild mode Hi:33 Me:32 Lo:31

48

Exterior dimensions Height × Width × Depth

mm

Unit 270 × 840 × 840 Panel 35 × 950 × 950

595 × 780 (+67) × 290

Net weight kg 31 (Unit:24 Panel:7) 40 Refrigerant equipment

Compressor type & Q’ty

–

5CS102XFD × 1

Starting method – Direct line start

Heat exchanger

Louver fin & inner grooved tubing Straight fin & inner grooved tubing

Refrigerant control – Electronic expansion valve

Refrigerant R410A

Quantity kg –

1.55 [Pre-charged up to the piping length of 30m]

Refrigerant oil

r

–

0.48 (RB68A)

Defrost control Microcomputer controlled de-icer

Air handling equipment

Fan type & Q’ty

Turbo fan × 1 Propeller fan × 1

Motor W 14 × 134 × 1 Starting method Direct line start Direct line start

Air ﬂ ow CMM

Powerful mode Hi:18 Me:15 Lo:14

Mild mode Hi:15 Me:14 Lo:13

41

Outside air intake

Available – Air filter, Q’ty Plastic net (washable) × 1 – Shock & vibration absorber Rubber sleeve (for fan motor) Rubber mount (for compressor) Electric heater W – 20 (Crank case heater)

Operation control

Operation switch

Wired remote control switch (Optional : RC-E1R)

Wireless kit (Optional : RCN-T-35W-ER)

– (Indoor unit side)

Room temperature control Thermostat by electronics –

Safety equipment

Internal thermostat for fan motor.

Frost protection thermostat.

Internal thermostat for fan motor.

Anomalous discharge temperature protection.

Installation data Refrigerant piping size

mm

(in)

Liquid line: φ6.35 (1/4″) Gas line: φ12.7 (1/2″)

Connecting method Flare piping

Drain hose

Connectable with VP25 (I.D. 25mm, O.D. 32mm) – Insulation for piping Necessary (both Liquid & Gas lines) Accessories Mounting kit. Drain hose Optional parts Decorative Panel (T-PSA-35W-ER)

Notes (1) The data are measured at the following conditions.

Item

Operation

Indoor air temperature Outdoor air temperature

Standards

DB WB DB WB

Cooling 27˚C 19˚C 35˚C 24˚C

ISO-T1

Heating 20˚C – 7˚C 6˚C

(2) This packaged air-conditioner is manufactured and tested in conformity with the following standard. ISO-T1 “UNITARY AIR-CONDITIONERS” (3) The operation data indicate when the air-conditioner is operated at 230V 50Hz or 220V 60Hz. (4) Values in [ ~ ] show the minimum to maximum range.

-

14

-

Model FDTVA251HEN1R

Model

Item

FDTVA251HEN1R

FDTA251R FDCVA251HENR

Nominal cooling capacity

(1)

kW

5.6 [2.8~6.3]

Nominal heating capacity

(1)

kW

6.7 [3.1~7.1]

Power source 1 Phase, 220-240V 50Hz/220V 60Hz

Operation data

(3)

Cooling power consumption kW

1.64/1.65

Running current (Cooling) A

7.3/7.6

Power factor (Cooling) %

98/99

Heating power consumption kW

1.78/1.79

Running current (Heating) A

7.9/8.4

Power factor (Heating) %

98/97

Inrush current (L.R.A) A

5

Noise level dB(A)

Powerful mode Hi:38 Me:35 Lo:33

Mild mode Hi:35 Me:33 Lo:31

48

Exterior dimensions Height × Width × Depth

mm

Unit 270 × 840 × 840 Panel 35 × 950 × 950

595 × 780 (+67) × 290

Net weight kg 31 (Unit:24 Panel:7) 40 Refrigerant equipment

Compressor type & Q’ty

–

5CS102XFD × 1

Starting method – Direct line start

Heat exchanger

Louver fin & inner grooved tubing Straight fin & inner grooved tubing

Refrigerant control – Electronic expansion valve

Refrigerant R410A

Quantity kg –

1.75 [Pre-charged up to the piping length of 30m]

Refrigerant oil

r

–

0.48 (RB68A)

Defrost control Microcomputer controlled de-icer

Air handling equipment

Fan type & Q’ty

Turbo fan × 1 Propeller fan × 1

Motor W 20 × 134 × 1 Starting method Direct line start Direct line start

Air ﬂ ow CMM

Powerful mode Hi:20 Me:17 Lo:15

Mild mode Hi:17 Me:15 Lo:13

41

Outside air intake

Available – Air filter, Q’ty Plastic net (washable) × 1 – Shock & vibration absorber Rubber sleeve (for fan motor) Rubber mount (for compressor) Electric heater W – 20 (Crank case heater)

Operation control

Operation switch

Wired remote control switch (Optional : RC-E1R)

Wireless kit (Optional : RCN-T-35W-ER)

– (Indoor unit side)

Room temperature control Thermostat by electronics –

Safety equipment

Internal thermostat for fan motor.

Frost protection thermostat.

Internal thermostat for fan motor.

Anomalous discharge temperature protection.

Installation data Refrigerant piping size

mm

(in)

Liquid line: φ6.35 (1/4″) Gas line: φ15.88 (5/8″)

Connecting method Flare piping

Drain hose

Connectable with VP25 (I.D. 25mm, O.D. 32mm) – Insulation for piping Necessary (both Liquid & Gas lines) Accessories Mounting kit. Drain hose Optional parts Decorative Panel (T-PSA-35W-ER)

Notes (1) The data are measured at the following conditions.

Item

Operation

Indoor air temperature Outdoor air temperature

Standards

DB WB DB WB

Cooling 27˚C 19˚C 35˚C 24˚C

ISO-T1

Heating 20˚C – 7˚C 6˚C

(2) This packaged air-conditioner is manufactured and tested in conformity with the following standard. ISO-T1 “UNITARY AIR-CONDITIONERS” (3) The operation data indicate when the air-conditioner is operated at 230V 50Hz or 220V 60Hz. (4) Values in [ ~ ] show the minimum to maximum range.

-

15

-

Model FDTVA302HEN1R

Model

Item

FDTVA302HEN1R

FDTA301R FDCVA302HENR

Nominal cooling capacity

(1)

kW

7.1[3.9~8.0]

Nominal heating capacity

(1)

kW

8.0[4.0~9.0]

Power source 1 Phase, 220-240V 50Hz/220V 60Hz

Operation data

(3)

Cooling power consumption kW

1.90/1.91

Running current (Cooling) A

8.3/8.8

Power factor (Cooling) %

99/99

Heating power consumption kW

2.07/2.08

Running current (Heating) A

9.0/9.6

Power factor (Heating) %

99/98

Inrush current (L.R.A) A

5

Noise level dB(A)

Powerful mode Hi:38 Me:35 Lo:33

Mild mode Hi:35 Me:33 Lo:31

48

Exterior dimensions Height × Width × Depth

mm

Unit 270 × 840 × 840 Panel 35 × 950 × 950

750 × 880 (+88) × 340

Net weight kg 31 (Unit:24 Panel:7) 60 Refrigerant equipment

Compressor type & Q’ty

–

2YC45DXD × 1

Starting method – Direct line start

Heat exchanger

Louver fin & inner grooved tubing Straight fin & inner grooved tubing

Refrigerant control – Electronic expansion valve

Refrigerant R410A

Quantity kg –

2.95 [Pre-charged up to the piping length of 30m]

Refrigerant oil

r

–

0.65 (FVC50K)

Defrost control Microcomputer controlled de-icer

Air handling equipment

Fan type & Q’ty

Turbo fan × 1 Propeller fan × 1

Motor W 20 × 1120 × 1 Starting method Direct line start

Air ﬂ ow CMM

Powerful mode Hi:20 Me:17 Lo:15

Mild mode Hi:17 Me:15 Lo:13

Cooling:60 Heating:48.5

Outside air intake

Available – Air filter, Q’ty Plastic net (washable) × 1 – Shock & vibration absorber Rubber sleeve (for fan motor) Rubber mount (for compressor) Electric heater W – 20 (Crank case heater)

Operation control

Operation switch

Wired remote control switch (Optional : RC-E1R)

Wireless kit (Optional : RCN-T-35W-ER)

– (Indoor unit side)

Room temperature control Thermostat by electronics –

Safety equipment

Internal thermostat for fan motor.

Frost protection thermostat.

Internal thermostat for fan motor.

Anomalous discharge temperature protection.

Installation data Refrigerant piping size

mm

(in)

Liquid line: φ9.52 (3/8″) Gas line: φ15.88 (5/8″)

Connecting method Flare piping

Drain hose

Connectable with VP25 (I.D. 25mm, O.D. 32mm) – Insulation for piping Necessary (both Liquid & Gas lines) Accessories Mounting kit. Drain hose Optional parts Decorative Panel (T-PSA-35W-ER)

Notes (1) The data are measured at the following conditions.

Item

Operation

Indoor air temperature Outdoor air temperature

Standards

DB WB DB WB

Cooling 27˚C 19˚C 35˚C 24˚C

ISO-T1

Heating 20˚C – 7˚C 6˚C

(2) This packaged air-conditioner is manufactured and tested in conformity with the following standard. ISO-T1 “UNITARY AIR-CONDITIONERS” (3) The operation data indicate when the air-conditioner is operated at 230V 50Hz or 220V 60Hz. (4) Values in [ ~ ] show the minimum to maximum range.

-

16

-

Model FDTVA402HEN2R

Model

Item

FDTVA402HEN2R

(5)

FDTA401R FDCVA402HENAR

Nominal cooling capacity

(1)

kW

10.0 [6.1~11.2]

Nominal heating capacity

(1)

kW

11.2 [5.6~12.5]

Power source 1 Phase, 220-240V 50Hz

Operation data

(3)

Cooling power consumption kW

2.88

Running current (Cooling) A

12.6

Power factor (Cooling) %

99

Heating power consumption kW

3.12

Running current (Heating) A

13.7

Power factor (Heating) %

99

Inrush current (L.R.A) A

5

Noise level dB(A)

Powerful mode Hi:46 Me:43 Lo:41

Mild mode Hi:43 Me:41 Lo:38

50

Exterior dimensions Height × Width × Depth

mm

Unit 295 × 840 × 840 Panel 35 × 950 × 950

845 × 970 × 370

Net weight kg 33 (Unit:26 Panel:7) 74 Refrigerant equipment

Compressor type & Q’ty

–

RM-B5125MDE21 × 1

Starting method – Direct line start

Heat exchanger

Louver fin & inner grooved tubing Straight fin & inner grooved tubing

Refrigerant control – Electronic expansion valve

Refrigerant R410A

Quantity kg –

3.8 [Pre-charged up to the piping length of 30m]

Refrigerant oil

r

–

0.7 (M-MA68)

Defrost control Microcomputer controlled de-icer

Air handling equipment

Fan type & Q’ty

Turbo fan × 1 Propeller fan × 1

Motor W 40 × 1120 × 1 Starting method Direct line start Direct line start

Air ﬂ ow CMM

Powerful mode Hi:25 Me:22 Lo:20

Mild mode Hi:22 Me:20 Lo:18

Cooling: 75, Heating: 73

Outside air intake

Available – Air filter, Q’ty Plastic net (washable) × 1 – Shock & vibration absorber Rubber sleeve (for fan motor) Rubber mount (for compressor) Electric heater W – 20 (Crank case heater)

Operation control

Operation switch

Wired remote control switch (Optional : RC-E1R)

Wireless kit (Optional : RCN-T-35W-ER)

– (Indoor unit side)

Room temperature control Thermostat by electronics –

Safety equipment

Internal thermostat for fan motor.

Frost protection thermostat.

Internal thermostat for fan motor.

Anomalous discharge temperature protection.

Installation data Refrigerant piping size

mm

(in)

Liquid line: φ9.52 (3/8″) Gas line: φ15.88 (5/8″)

Connecting method Flare piping

Drain hose

Connectable with VP25 (I.D. 25mm, O.D. 32mm) – Insulation for piping Necessary (both Liquid & Gas lines) Accessories Mounting kit. Drain hose Optional parts Decorative Panel (T-PSA-35W-ER)

Notes (1) The data are measured at the following conditions.

Item

Operation

Indoor air temperature Outdoor air temperature

Standards

DB WB DB WB

Cooling 27˚C 19˚C 35˚C 24˚C

ISO-T1

Heating 20˚C – 7˚C 6˚C

(2) This packaged air-conditioner is manufactured and tested in conformity with the following standard. ISO-T1 “UNITARY AIR-CONDITIONERS” (3) The operation data indicate when the air-conditioner is operated at 230V 50Hz. (4) Values in [ ~ ] show the minimum to maximum range. (5) Not available in 60Hz.

-

17

-

Model FDTVA402HES2R

Model

Item

FDTVA402HES2R

(5)

FDTA401R FDCVA402HESAR

Nominal cooling capacity

(1)

kW

10.0 [6.1~11.2]

Nominal heating capacity

(1)

kW

11.2 [5.6~12.5]

Power source 3 Phase, 380-415V 50Hz

Operation data

(3)

Cooling power consumption kW

2.97

Running current (Cooling) A

4.7

Power factor (Cooling) %

91

Heating power consumption kW

2.92

Running current (Heating) A

4.6

Power factor (Heating) %

92

Inrush current (L.R.A) A

5

Noise level dB(A)

Powerful mode Hi:46 Me:43 Lo:41

Mild mode Hi:43 Me:41 Lo:38

50

Exterior dimensions Height × Width × Depth

mm

Unit 295 × 840 × 840 Panel 35 × 950 × 950

845 × 970 × 370

Net weight kg 33 (Unit:26 Panel:7) 74 Refrigerant equipment

Compressor type & Q’ty

–

RM-B5125MDE31 × 1

Starting method – Direct line start

Heat exchanger

Louver fin & inner grooved tubing Straight fin & inner grooved tubing

Refrigerant control – Electronic expansion valve

Refrigerant R410A

Quantity kg –

3.8 [Pre-charged up to the piping length of 30m]

Refrigerant oil

r

–

0.7 (M-MA68)

Defrost control Microcomputer controlled de-icer

Air handling equipment

Fan type & Q’ty

Turbo fan × 1 Propeller fan × 1

Motor W 40 × 1120 × 1 Starting method Direct line start Direct line start

Air ﬂ ow CMM

Powerful mode Hi:25 Me:22 Lo:20

Mild mode Hi:22 Me:20 Lo:18

Cooling: 75, Heating: 73

Outside air intake

Available – Air filter, Q’ty Plastic net (washable) × 1 – Shock & vibration absorber Rubber sleeve (for fan motor) Rubber mount (for compressor) Electric heater W – 20 (Crank case heater)

Operation control

Operation switch

Wired remote control switch (Optional : RC-E1R)

Wireless kit (Optional : RCN-T-35W-ER)

– (Indoor unit side)

Room temperature control Thermostat by electronics –

Safety equipment

Internal thermostat for fan motor.

Frost protection thermostat.

Internal thermostat for fan motor.

Anomalous discharge temperature protection.

Installation data Refrigerant piping size

mm

(in)

Liquid line: φ9.52 (3/8″) Gas line: φ15.88 (5/8″)

Connecting method Flare piping

Drain hose

Connectable with VP25 (I.D. 25mm, O.D. 32mm) – Insulation for piping Necessary (both Liquid & Gas lines) Accessories Mounting kit. Drain hose Optional parts Decorative Panel (T-PSA-35W-ER)

Notes (1) The data are measured at the following conditions.

Item

Operation

Indoor air temperature Outdoor air temperature

Standards

DB WB DB WB

Cooling 27˚C 19˚C 35˚C 24˚C

ISO-T1

Heating 20˚C – 7˚C 6˚C

(2) This packaged air-conditioner is manufactured and tested in conformity with the following standard. ISO-T1 “UNITARY AIR-CONDITIONERS” (3) The operation data indicate when the air-conditioner is operated at 400V 50Hz. (4) Values in [ ~ ] show the minimum to maximum range. (5) Not available in 60Hz.

-

18

-

Model FDTAV502HEN2R

Model

Item

FDTVA502HEN2R

FDTA501R FDCVA502HENAR

Nominal cooling capacity

(1)

kW

12.5 [6.5~14.0]

Nominal heating capacity

(1)

kW

14.0 [6.2~16.0]

Power source 1 Phase, 220-240V 50Hz/220V 60Hz

Operation data

(3)

Cooling power consumption kW

4.05/4.05

Running current (Cooling) A

17.7/18.6

Power factor (Cooling) %

99/99

Heating power consumption kW

3.97/3.97

Running current (Heating) A

17.4/18.2

Power factor (Heating) %

99/99

Inrush current (L.R.A) A

5

Noise level dB(A)

Powerful mode Hi:48 Me:45 Lo:43

Mild mode Hi:45 Me:43 Lo:40

52

Exterior dimensions Height × Width × Depth

mm

Unit 365 × 840 × 840 Panel 35 × 950 × 950

845 × 970 × 370

Net weight kg 33 (Unit:31 Panel:7) 74 Refrigerant equipment

Compressor type & Q’ty

–

RM-B5125MDE21 × 1

Starting method – Direct line start

Heat exchanger

Louver fin & inner grooved tubing Straight fin & inner grooved tubing

Refrigerant control – Electronic expansion valve

Refrigerant R410A

Quantity kg –

3.8 [Pre-charged up to the piping length of 30m]

Refrigerant oil

r

–

0.7 (M-MA68)

Defrost control Microcomputer controlled de-icer

Air handling equipment

Fan type & Q’ty

Turbo fan × 1 Propeller fan × 1

Motor W 120 × 1120 × 1 Starting method Direct line start Direct line start

Air ﬂ ow CMM

Powerful mode Hi:32 Me:29 Lo:26

Mild mode Hi:29 Me:26 Lo:23

Cooling: 75, Heating: 73

Outside air intake

Available – Air filter, Q’ty Plastic net (washable) × 1 – Shock & vibration absorber Rubber sleeve (for fan motor) Rubber mount (for compressor) Electric heater W – 20 (Crank case heater)

Operation control

Operation switch

Wired remote control switch (Optional : RC-E1R)

Wireless kit (Optional : RCN-T-35W-ER)

– (Indoor unit side)

Room temperature control Thermostat by electronics –

Safety equipment

Internal thermostat for fan motor.

Frost protection thermostat.

Internal thermostat for fan motor.

Anomalous discharge temperature protection.

Installation data Refrigerant piping size

mm

(in)

Liquid line: φ9.52 (3/8″) Gas line: φ15.88 (5/8″)

Connecting method Flare piping

Drain hose

Connectable with VP25 (I.D. 25mm, O.D. 32mm) – Insulation for piping Necessary (both Liquid & Gas lines) Accessories Mounting kit. Drain hose Optional parts Decorative Panel (T-PSA-35W-ER)

Notes (1) The data are measured at the following conditions.

Item

Operation

Indoor air temperature Outdoor air temperature

Standards

DB WB DB WB

Cooling 27˚C 19˚C 35˚C 24˚C

ISO-T1

Heating 20˚C – 7˚C 6˚C

(2) This packaged air-conditioner is manufactured and tested in conformity with the following standard. ISO-T1 “UNITARY AIR-CONDITIONERS” (3) The operation data indicate when the air-conditioner is operated at 230V 50Hz or 220V 60Hz. (4) Values in [ ~ ] show the minimum to maximum range.

-

19

-

Model FDTAV502HES2R

Model

Item

FDTVA502HES2R

FDTA501R FDCVA502HESAR

Nominal cooling capacity

(1)

kW

12.5 [6.5~14.0]

Nominal heating capacity

(1)

kW

14.0 [6.2~16.0]

Power source 3 Phase, 380-415V 50Hz/380V 60Hz

Operation data

(3)

Cooling power consumption kW

4.05/4.05

Running current (Cooling) A

5.9/6.3

Power factor (Cooling) %

99/98

Heating power consumption kW

3.97/3.97

Running current (Heating) A

5.8/6.3

Power factor (Heating) %

99/96

Inrush current (L.R.A) A

5

Noise level dB(A)

Powerful mode Hi:48 Me:45 Lo:43

Mild mode Hi:45 Me:43 Lo:40

52

Exterior dimensions Height × Width × Depth

mm

Unit 365 × 840 × 840 Panel 35 × 950 × 950

845 × 970 × 370

Net weight kg 38 (Unit:31 Panel:7) 74 Refrigerant equipment

Compressor type & Q’ty

–

RM-B5125MDE31 × 1

Starting method – Direct line start

Heat exchanger

Louver fin & inner grooved tubing Straight fin & inner grooved tubing

Refrigerant control – Electronic expansion valve

Refrigerant R410A

Quantity kg –

3.8 [Pre-charged up to the piping length of 30m]

Refrigerant oil

r

–

0.7 (M-MA68)

Defrost control Microcomputer controlled de-icer

Air handling equipment

Fan type & Q’ty

Turbo fan × 1 Propeller fan × 1

Motor W 120 × 1120 × 1 Starting method Direct line start Direct line start

Air ﬂ ow CMM

Powerful mode Hi:32 Me:29 Lo:26

Mild mode Hi:29 Me:26 Lo:23

Cooling: 75, Heating: 73

Outside air intake

Available – Air filter, Q’ty Plastic net (washable) × 1 – Shock & vibration absorber Rubber sleeve (for fan motor) Rubber mount (for compressor) Electric heater W – 20 (Crank case heater)

Operation control

Operation switch

Wired remote control switch (Optional : RC-E1R)

Wireless kit (Optional : RCN-T-35W-ER)

– (Indoor unit side)

Room temperature control Thermostat by electronics –

Safety equipment

Internal thermostat for fan motor.

Frost protection thermostat.

Internal thermostat for fan motor.

Anomalous discharge temperature protection.

Installation data Refrigerant piping size

mm

(in)

Liquid line: φ9.52 (3/8″) Gas line: φ15.88 (5/8″)

Connecting method Flare piping

Drain hose

Connectable with VP25 (I.D. 25mm, O.D. 32mm) – Insulation for piping Necessary (both Liquid & Gas lines) Accessories Mounting kit. Drain hose Optional parts Decorative Panel (T-PSA-35W-ER)

Notes (1) The data are measured at the following conditions.

Item

Operation

Indoor air temperature Outdoor air temperature

Standards

DB WB DB WB

Cooling 27˚C 19˚C 35˚C 24˚C

ISO-T1

Heating 20˚C – 7˚C 6˚C

(2) This packaged air-conditioner is manufactured and tested in conformity with the following standard. ISO-T1 “UNITARY AIR-CONDITIONERS” (3) The operation data indicate when the air-conditioner is operated at 400V 50Hz or 380V 60Hz. (4) Values in [ ~ ] show the minimum to maximum range.

-

20

-

Model FDTVA602HEN2R

Model

Item

FDTVA602HEN2R

FDTA601R FDCVA602HENAR

Nominal cooling capacity

(1)

kW

14.0 [6.7~14.8]

Nominal heating capacity

(1)

kW

16.0 [6.3~16.8]

Power source 1 Phase, 220-240V 50Hz/220V 60Hz

Operation data

(3)

Cooling power consumption kW

4.65/4.65

Running current (Cooling) A

20.4/21.3

Power factor (Cooling) %

99/99

Heating power consumption kW

4.54/4.54

Running current (Heating) A

20.0/20.9

Power factor (Heating) %

99/99

Inrush current (L.R.A) A

5

Noise level dB(A)

Powerful mode Hi:48 Me:45 Lo:43

Mild mode Hi:45 Me:43 Lo:40

53

Exterior dimensions Height × Width × Depth

mm

Unit 365 × 840 × 840 Panel 35 × 950 × 950

845 × 970 × 370

Net weight kg 38 (Unit:31 Panel:7) 74 Refrigerant equipment

Compressor type & Q’ty

–

RM-B5125MDE21 × 1

Starting method – Direct line start

Heat exchanger

Louver fin & inner grooved tubing Straight fin & inner grooved tubing

Refrigerant control – Electronic expansion valve

Refrigerant R410A

Quantity kg –

3.8 [Pre-charged up to the piping length of 30m]

Refrigerant oil

r

–

0.7 (M-MA68)

Defrost control Microcomputer controlled de-icer

Air handling equipment

Fan type & Q’ty

Turbo fan × 1 Propeller fan × 1

Motor W 120 × 1120 × 1 Starting method Direct line start Direct line start

Air ﬂ ow CMM

Powerful mode Hi:34 Me:30 Lo:26

Mild mode Hi:30 Me:26 Lo:23

Cooling: 75, Heating: 73

Outside air intake

Available – Air filter, Q’ty Plastic net (washable) × 1 – Shock & vibration absorber Rubber sleeve (for fan motor) Rubber mount (for compressor) Electric heater W – 20 (Crank case heater)

Operation control

Operation switch

Wired remote control switch (Optional : RC-E1R)

Wireless kit (Optional : RCN-T-35W-ER)

– (Indoor unit side)

Room temperature control Thermostat by electronics –

Safety equipment

Internal thermostat for fan motor.

Frost protection thermostat.

Internal thermostat for fan motor.

Anomalous discharge temperature protection.

Installation data Refrigerant piping size

mm

(in)

Liquid line: φ9.52 (3/8″) Gas line: φ15.88 (5/8″)

Connecting method Flare piping

Drain hose

Connectable with VP25 (I.D. 25mm, O.D. 32mm) – Insulation for piping Necessary (both Liquid & Gas lines) Accessories Mounting kit. Drain hose Optional parts Decorative Panel (T-PSA-35W-ER)

Notes (1) The data are measured at the following conditions.

Item

Operation

Indoor air temperature Outdoor air temperature

Standards

DB WB DB WB

Cooling 27˚C 19˚C 35˚C 24˚C

ISO-T1

Heating 20˚C – 7˚C 6˚C

(2) This packaged air-conditioner is manufactured and tested in conformity with the following standard. ISO-T1 “UNITARY AIR-CONDITIONERS” (3) The operation data indicate when the air-conditioner is operated at 230V 50Hz or 220V 60Hz. (4) Values in [ ~ ] show the minimum to maximum range.

-

21

-

Model FDTVA602HES2R

Model

Item

FDTVA602HES2R

FDTA601R FDCVA602HESAR

Nominal cooling capacity

(1)

kW

14.0 [6.7~14.8]

Nominal heating capacity

(1)

kW

16.0 [6.3~16.8]

Power source 3 Phase, 380-415V 50Hz/380V 60Hz

Operation data

(3)

Cooling power consumption kW

4.65/4.65

Running current (Cooling) A

6.8/7.3

Power factor (Cooling) %

99/97

Heating power consumption kW

4.54/4.54

Running current (Heating) A

6.7/7.4

Power factor (Heating) %

98/93

Inrush current (L.R.A) A

5

Noise level dB(A)

Powerful mode Hi:48 Me:45 Lo:43

Mild mode Hi:45 Me:43 Lo:40

53

Exterior dimensions Height × Width × Depth

mm

Unit 365 × 840 × 840 Panel 35 × 950 × 950

845 × 970 × 370

Net weight kg 38 (Unit:31 Panel:7) 74 Refrigerant equipment

Compressor type & Q’ty

–

RM-B5125MDE31 × 1

Starting method – Direct line start

Heat exchanger

Louver fin & inner grooved tubing Straight fin & inner grooved tubing

Refrigerant control – Electronic expansion valve

Refrigerant R410A

Quantity kg –

3.8 [Pre-charged up to the piping length of 30m]

Refrigerant oil

r

–

0.7 (M-MA68)

Defrost control Microcomputer controlled de-icer

Air handling equipment

Fan type & Q’ty

Turbo fan × 1 Propeller fan × 1

Motor W 120 × 1120 × 1 Starting method Direct line start Direct line start

Air ﬂ ow CMM

Powerful mode Hi:34 Me:30 Lo:26

Mild mode Hi:30 Me:26 Lo:23

Cooling: 75, Heating: 73

Outside air intake

Available – Air filter, Q’ty Plastic net (washable) × 1 – Shock & vibration absorber Rubber sleeve (for fan motor) Rubber mount (for compressor) Electric heater W – 20 (Crank case heater)

Operation control

Operation switch

Wired remote control switch (Optional : RC-E1R)

Wireless kit (Optional : RCN-T-35W-ER)

– (Indoor unit side)

Room temperature control Thermostat by electronics –

Safety equipment

Internal thermostat for fan motor.

Frost protection thermostat.

Internal thermostat for fan motor.

Anomalous discharge temperature protection.

Installation data Refrigerant piping size

mm

(in)

Liquid line: φ9.52 (3/8″) Gas line: φ15.88 (5/8″)

Connecting method Flare piping

Drain hose

Connectable with VP25 (I.D. 25mm, O.D. 32mm) – Insulation for piping Necessary (both Liquid & Gas lines) Accessories Mounting kit. Drain hose Optional parts Decorative Panel (T-PSA-35W-ER)

Notes (1) The data are measured at the following conditions.

Item

Operation

Indoor air temperature Outdoor air temperature

Standards

DB WB DB WB

Cooling 27˚C 19˚C 35˚C 24˚C

ISO-T1

Heating 20˚C – 7˚C 6˚C

(2) This packaged air-conditioner is manufactured and tested in conformity with the following standard. ISO-T1 “UNITARY AIR-CONDITIONERS” (3) The operation data indicate when the air-conditioner is operated at 400V 50Hz or 380V 60Hz. (4) Values in [ ~ ] show the minimum to maximum range.

-

22

-

(b) Twin type

Model FDTVA302HENP1R (Indoor unit: 2 units, Outdoor unit: 1 unit)

Model

Item

FDTVA302HENP1R

FDTA151R FDCVA302HENR

Nominal cooling capacity

(1)

kW

7.1[3.9~8.0]

Nominal heating capacity

(1)

kW

8.0[4.0~9.0]

Power source 1 Phase, 220-240V 50Hz/220V 60Hz

Operation data

(3)

Cooling power consumption kW

1.85/1.87

Running current (Cooling) A

8.0/8.6

Power factor (Cooling) %

99/99

Heating power consumption kW

1.99/1.99

Running current (Heating) A

8.7/9.1

Power factor (Heating) %

99/99

Inrush current (L.R.A) A

5

Noise level dB(A)

Powerful mode Hi:36 Me:33 Lo:32

Mild mode Hi:33 Me:32 Lo:31

48

Exterior dimensions Height × Width × Depth

mm

Unit 270 × 840 × 840 Panel 30 × 950 × 950

750 × 880 (+88) × 340

Net weight kg 31 (Unit:24 Panel:7) 60 Refrigerant equipment

Compressor type & Q’ty

–

2YC45DXD × 1

Starting method – Direct line start

Heat exchanger

Louver fin & inner grooved tubing Straight fin & inner grooved tubing

Refrigerant control – Electronic expansion valve

Refrigerant R410A

Quantity kg –

2.95 [Pre-charged up to the piping length of 30m]

Refrigerant oil

r

–

0.65 (FVC50K)

Defrost control Microcomputer controlled de-icer

Air handling equipment

Fan type & Q’ty

Turbo fan × 1 Propeller fan × 1

Motor W 14 × 1120 × 1 Starting method Direct line start

Air ﬂ ow CMM

Powerful mode Hi:18 Me:15 Lo:14

Mild mode Hi:15 Me:14 Lo:13

Cooling:60 Heating:48.5

Outside air intake

Available – Air filter, Q’ty Plastic net (washable) × 1 – Shock & vibration absorber Rubber sleeve (for fan motor) Rubber mount (for compressor) Electric heater W – 20 (Crank case heater)

Operation control

Operation switch

Wired remote control switch (Optional : RC-E1R)

Wireless kit (Optional : RCN-T-35W-ER)

– (Indoor unit side)

Room temperature control Thermostat by electronics –

Safety equipment

Internal thermostat for fan motor.

Frost protection thermostat.

Internal thermostat for fan motor.

Anomalous discharge temperature protection.

Installation data Refrigerant piping size

Liquid line

mm

(in)

Indoor branch pipe, Outdoor main pipe: φ9.52 (3/8″)

Gas line Indoor branch pipe: φ12.7 (1/2″), Outdoor main pipe: φ15.88 (5/8″)

Connecting method Flare piping

Drain hose

Connectable with VP25 (I.D. 25mm, O.D. 32mm) – Insulation for piping Necessary (both Liquid & Gas lines) Accessories Mounting kit. Drain hose Optional parts Decorative Panel (T-PSA-35W-ER)

Notes (1) The data are measured at the following conditions.

Item

Operation

Indoor air temperature Outdoor air temperature

Standards

DB WB DB WB

Cooling 27˚C 19˚C 35˚C 24˚C

ISO-T1

Heating 20˚C – 7˚C 6˚C

(2) This packaged air-conditioner is manufactured and tested in conformity with the following standard. ISO-T1 “UNITARY AIR-CONDITIONERS” (3) The operation data indicate when the air-conditioner is operated at 230V 50Hz or 220V 60Hz. (4) Values in [ ~ ] show the minimum to maximum range. (5) Indoor unit specifications show the specifications for one unit. Capacity and running characteristics values are shown for the case where two indoor

units are combined and run together.

-

23

-

Model FDTVA402HENP2R (Indoor unit: 2 units, Outdoor unit: 1 unit)

Model

Item

FDTVA402HENP2R

(6)

FDTA201R FDCVA402HENAR

Nominal cooling capacity

(1)

kW

10.0 [6.1~11.2]

Nominal heating capacity

(1)

kW

11.2 [5.6~12.5]

Power source 1 Phase, 220-240V 50Hz

Operation data

(3)

Cooling power consumption kW

2.94/2.96

Running current (Cooling) A

12.9/13.7

Power factor (Cooling) %

99/98

Heating power consumption kW

3.09/3.09

Running current (Heating) A

13.6/14.2

Power factor (Heating) %

99/99

Inrush current (L.R.A) A

5

Noise level dB(A)

Powerful mode Hi:36 Me:33 Lo:32

Mild mode Hi:33 Me:32 Lo:31

50

Exterior dimensions Height × Width × Depth

mm

Unit 270 × 840 × 840 Panel 35 × 950 × 950

845 × 970 × 370

Net weight kg 31 (Unit:24 Panel:7) 74 Refrigerant equipment

Compressor type & Q’ty

–

RM-B5125MDE21 × 1

Starting method – Direct line start

Heat exchanger

Louver fin & inner grooved tubing Straight fin & inner grooved tubing

Refrigerant control – Electronic expansion valve

Refrigerant R410A

Quantity kg –

3.8 [Pre-charged up to the piping length of 30m]

Refrigerant oil

r

–

0.7 (M-MA68)

Defrost control Microcomputer controlled de-icer

Air handling equipment

Fan type & Q’ty

Turbo fan × 1 Propeller fan × 1

Motor W 14 × 1120 × 1 Starting method Direct line start Direct line start

Air ﬂ ow CMM

Powerful mode Hi:18 Me:15 Lo:14

Mild mode Hi:15 Me:14 Lo:13

Cooling: 75, Heating: 73

Outside air intake

Available – Air filter, Q’ty Plastic net (washable) × 1 – Shock & vibration absorber Rubber sleeve (for fan motor) Rubber mount (for compressor) Electric heater W – 20 (Crank case heater)

Operation control

Operation switch

Wired remote control switch (Optional : RC-E1R)

Wireless kit (Optional : RCN-T-35W-ER)

– (Indoor unit side)

Room temperature control Thermostat by electronics –

Safety equipment

Internal thermostat for fan motor.

Frost protection thermostat.

Internal thermostat for fan motor.

Anomalous discharge temperature protection.

Installation data Refrigerant piping size

Liquid line

mm

(in)

Indoor branch pipe, Outdoor main pipe: φ9.52 (3/8″)

Gas line Indoor branch pipe: φ12.7 (1/2″), Outdoor main pipe: φ15.88 (5/8″)

Connecting method Flare piping

Drain hose

Connectable with VP25 (I.D. 25mm, O.D. 32mm) – Insulation for piping Necessary (both Liquid & Gas lines) Accessories Mounting kit. Drain hose Optional parts Decorative Panel (T-PSA-35W-ER)

Notes (1) The data are measured at the following conditions.

Item

Operation

Indoor air temperature Outdoor air temperature

Standards

DB WB DB WB

Cooling 27˚C 19˚C 35˚C 24˚C

ISO-T1

Heating 20˚C – 7˚C 6˚C

(2) This packaged air-conditioner is manufactured and tested in conformity with the following standard. ISO-T1 “UNITARY AIR-CONDITIONERS” (3) The operation data indicate when the air-conditioner is operated at 230V 50Hz. (4) Values in [ ~ ] show the minimum to maximum range. (5) Indoor unit specifications show the specifications for one unit. Capacity and running characteristics values are shown for the case where two indoor

units are combined and run together.

(6) Not available in 60Hz.

-

24

-

Model FDTVA402HESP2R (Indoor unit: 2 units, Outdoor unit: 1 unit)

Model

Item

FDTVA402HESP2R

FDTA201R FDCVA402HESAR

Nominal cooling capacity

(1)

kW

10.0 [6.1~11.2]

Nominal heating capacity

(1)

kW

11.2 [5.6~12.5]

Power source 3 Phase, 380-415V 50Hz/380V 60Hz

Operation data

(3)

Cooling power consumption kW

2.94/2.96

Running current (Cooling) A

4.3/4.6

Power factor (Cooling) %

99/98

Heating power consumption kW

3.09/3.09

Running current (Heating) A

4.5/4.8

Power factor (Heating) %

99/98

Inrush current (L.R.A) A

5

Noise level dB(A)

Powerful mode Hi:36 Me:33 Lo:32

Mild mode Hi:33 Me:32 Lo:31

50

Exterior dimensions Height × Width × Depth

mm

Unit 270 × 840 × 840 Panel 35 × 950 × 950

845 × 970 × 370

Net weight kg 31 (Unit:24 Panel:7) 74 Refrigerant equipment

Compressor type & Q’ty

–

RM-B5125MDE31 × 1

Starting method – Direct line start

Heat exchanger

Louver fin & inner grooved tubing Straight fin & inner grooved tubing

Refrigerant control – Electronic expansion valve

Refrigerant R410A

Quantity kg –

3.8 [Pre-charged up to the piping length of 30m]

Refrigerant oil

r

–

0.7 (M-MA68)

Defrost control Microcomputer controlled de-icer

Air handling equipment

Fan type & Q’ty

Turbo fan × 1 Propeller fan × 1

Motor W 14 × 1120 × 1 Starting method Direct line start Direct line start

Air ﬂ ow CMM

Powerful mode Hi:18 Me:15 Lo:14

Mild mode Hi:15 Me:14 Lo:13

Cooling: 75, Heating: 73

Outside air intake

Available – Air filter, Q’ty Plastic net (washable) × 1 – Shock & vibration absorber Rubber sleeve (for fan motor) Rubber mount (for compressor) Electric heater W – 20 (Crank case heater)

Operation control

Operation switch

Wired remote control switch (Optional : RC-E1R)

Wireless kit (Optional : RCN-T-35W-ER)

– (Indoor unit side)

Room temperature control Thermostat by electronics –

Safety equipment

Internal thermostat for fan motor.

Frost protection thermostat.

Internal thermostat for fan motor.

Anomalous discharge temperature protection.

Installation data Refrigerant piping size

Liquid line

mm

(in)

Indoor branch pipe, Outdoor main pipe: φ9.52 (3/8″)

Gas line Indoor branch pipe: φ12.7 (1/2″), Outdoor main pipe: φ15.88 (5/8″)

Connecting method Flare piping

Drain hose

Connectable with VP25 (I.D. 25mm, O.D. 32mm) – Insulation for piping Necessary (both Liquid & Gas lines) Accessories Mounting kit. Drain hose Optional parts Decorative Panel (T-PSA-35W-ER)

Notes (1) The data are measured at the following conditions.

Item

Operation

Indoor air temperature Outdoor air temperature

Standards

DB WB DB WB

Cooling 27˚C 19˚C 35˚C 24˚C

ISO-T1

Heating 20˚C – 7˚C 6˚C

(2) This packaged air-conditioner is manufactured and tested in conformity with the following standard. ISO-T1 “UNITARY AIR-CONDITIONERS” (3) The operation data indicate when the air-conditioner is operated at 400V 50Hz or 380V 60Hz. (4) Values in [ ~ ] show the minimum to maximum range. (5) Indoor unit specifications show the specifications for one unit. Capacity and running characteristics values are shown for the case where two indoor

units are combined and run together.

-

25

-

Model FDTVA502HENP2R (Indoor unit: 2 units, Outdoor unit: 1 unit)

Model

Item

FDTVA502HENP2R

FDTA251R FDCVA502HENAR

Nominal cooling capacity

(1)

kW

12.5 [6.5~14.0]

Nominal heating capacity

(1)

kW

14.0 [6.2~16.0]

Power source 1 Phase, 220-240V 50Hz/220V 60Hz

Operation data

(3)

Cooling power consumption kW

4.29/4.31

Running current (Cooling) A

18.9/20.0

Power factor (Cooling) %

99/98

Heating power consumption kW

4.13/4.15

Running current (Heating) A

18.2/19.2

Power factor (Heating) %

99/98

Inrush current (L.R.A) A

5

Noise level dB(A)

Powerful mode Hi:38 Me:35 Lo:33

Mild mode Hi:35 Me:33 Lo:31

52

Exterior dimensions Height × Width × Depth

mm

Unit 270 × 840 × 840 Panel 35 × 950 × 950

845 × 970 × 370

Net weight kg 31 (Unit:24 Panel:7) 74 Refrigerant equipment

Compressor type & Q’ty

–

RM-B5125MDE21 × 1

Starting method – Direct line start

Heat exchanger

Louver fin & inner grooved tubing Straight fin & inner grooved tubing

Refrigerant control – Electronic expansion valve

Refrigerant R410A

Quantity kg –

3.8 [Pre-charged up to the piping length of 30m]

Refrigerant oil

r

–

0.7 (M-MA68)

Defrost control Microcomputer controlled de-icer

Air handling equipment

Fan type & Q’ty

Turbo fan × 1 Propeller fan × 1

Motor W 20 × 1120 × 1 Starting method Direct line start Direct line start

Air ﬂ ow CMM

Powerful mode Hi:20 Me:17 Lo:15

Mild mode Hi:17 Me:15 Lo:13

Cooling: 75, Heating: 73

Outside air intake

Available – Air filter, Q’ty Plastic net (washable) × 1 – Shock & vibration absorber Rubber sleeve (for fan motor) Rubber mount (for compressor) Electric heater W – 20 (Crank case heater)

Operation control

Operation switch

Wired remote control switch (Optional : RC-E1R)

Wireless kit (Optional : RCN-T-35W-ER)

– (Indoor unit side)

Room temperature control Thermostat by electronics –

Safety equipment

Internal thermostat for fan motor.

Frost protection thermostat.

Internal thermostat for fan motor.

Anomalous discharge temperature protection.

Installation data Refrigerant piping size

Liquid line

mm

(in)

Indoor branch pipe, Outdoor main pipe: φ9.52 (3/8″)

Gas line Indoor branch pipe, Outdoor main pipe: φ15.88 (5/8″)

Connecting method Flare piping

Drain hose

Connectable with VP25 (I.D. 25mm, O.D. 32mm) – Insulation for piping Necessary (both Liquid & Gas lines) Accessories Mounting kit. Drain hose Optional parts Decorative Panel (T-PSA-35W-ER)

Notes (1) The data are measured at the following conditions.

Item

Operation

Indoor air temperature Outdoor air temperature

Standards

DB WB DB WB

Cooling 27˚C 19˚C 35˚C 24˚C

ISO-T1

Heating 20˚C – 7˚C 6˚C

(2) This packaged air-conditioner is manufactured and tested in conformity with the following standard. ISO-T1 “UNITARY AIR-CONDITIONERS” (3) The operation data indicate when the air-conditioner is operated at 230V 50Hz or 220V 60Hz. (4) Values in [ ~ ] show the minimum to maximum range. (5) Indoor unit specifications show the specifications for one unit. Capacity and running characteristics values are shown for the case where two indoor

units are combined and run together.

-

26

-

Model FDTVA502HESP2R (Indoor unit: 2 units, Outdoor unit: 1 unit)

Model

Item

FDTVA502HESP2R

FDTA251R FDCVA502HESAR

Nominal cooling capacity

(1)

kW

12.5 [6.5~14.0]

Nominal heating capacity

(1)

kW

14.0 [6.2~16.0]

Power source 3 Phase, 380-415V 50Hz/380V 60Hz

Operation data

(3)

Cooling power consumption kW

4.29/4.31

Running current (Cooling) A

6.3/6.7

Power factor (Cooling) %

98/98

Heating power consumption kW

4.13/4.15

Running current (Heating) A

6.1/6.4

Power factor (Heating) %

98/99

Inrush current (L.R.A) A

5

Noise level dB(A)

Powerful mode Hi:38 Me:35 Lo:33

Mild mode Hi:35 Me:33 Lo:31

52

Exterior dimensions Height × Width × Depth

mm

Unit 270 × 840 × 840 Panel 35 × 950 × 950

845 × 970 × 370

Net weight kg 31 (Unit:24 Panel:7) 74 Refrigerant equipment

Compressor type & Q’ty

–

RM-B5125MDE31 × 1

Starting method – Direct line start

Heat exchanger

Louver fin & inner grooved tubing Straight fin & inner grooved tubing

Refrigerant control – Electronic expansion valve

Refrigerant R410A

Quantity kg –

3.8 [Pre-charged up to the piping length of 30m]

Refrigerant oil

r

–

0.7 (M-MA68)

Defrost control Microcomputer controlled de-icer

Air handling equipment

Fan type & Q’ty

Turbo fan × 1 Propeller fan × 1

Motor W 20 × 1120 × 1 Starting method Direct line start Direct line start

Air ﬂ ow CMM

Powerful mode Hi:20 Me:17 Lo:15

Mild mode Hi:17 Me:15 Lo:13

Cooling: 75, Heating: 73

Outside air intake

Available – Air filter, Q’ty Plastic net (washable) × 1 – Shock & vibration absorber Rubber sleeve (for fan motor) Rubber mount (for compressor) Electric heater W – 20 (Crank case heater)

Operation control

Operation switch

Wired remote control switch (Optional : RC-E1R)

Wireless kit (Optional : RCN-T-35W-ER)

– (Indoor unit side)

Room temperature control Thermostat by electronics –

Safety equipment

Internal thermostat for fan motor.

Frost protection thermostat.

Internal thermostat for fan motor.

Anomalous discharge temperature protection.

Installation data Refrigerant piping size

Liquid line

mm

(in)

Indoor branch pipe, Outdoor main pipe: φ9.52 (3/8″)

Gas line Indoor branch pipe, Outdoor main pipe: φ15.88 (5/8″)

Connecting method Flare piping

Drain hose

Connectable with VP25 (I.D. 25mm, O.D. 32mm) – Insulation for piping Necessary (both Liquid & Gas lines) Accessories Mounting kit. Drain hose Optional parts Decorative Panel (T-PSA-35W-ER)

Notes (1) The data are measured at the following conditions.

Item

Operation

Indoor air temperature Outdoor air temperature

Standards

DB WB DB WB

Cooling 27˚C 19˚C 35˚C 24˚C

ISO-T1

Heating 20˚C – 7˚C 6˚C

(2) This packaged air-conditioner is manufactured and tested in conformity with the following standard. ISO-T1 “UNITARY AIR-CONDITIONERS” (3) The operation data indicate when the air-conditioner is operated at 400V 50Hz or 380V 60Hz. (4) Values in [ ~ ] show the minimum to maximum range. (5) Indoor unit specifications show the specifications for one unit. Capacity and running characteristics values are shown for the case where two indoor

units are combined and run together.

-

27

-

Model FDTVA602HENP2R (Indoor unit: 2 units, Outdoor unit: 1 unit)

Model

Item

FDTVA602HENP2R

FDTA301R FDCVA602HENAR

Nominal cooling capacity

(1)

kW

14.0 [7.0~14.5]

Nominal heating capacity

(1)

kW

16.0 [6.3~16.5]

Power source 1 Phase, 220-240V 50Hz/220V 60Hz

Operation data

(3)

Cooling power consumption kW

4.69/4.71

Running current (Cooling) A

20.5/21.6

Power factor (Cooling) %

99/99

Heating power consumption kW

4.58/4.60

Running current (Heating) A

20.1/21.2

Power factor (Heating) %

99/99

Inrush current (L.R.A) A

5

Noise level dB(A)

Powerful mode Hi:38 Me:35 Lo:33

Mild mode Hi:35 Me:33 Lo:31

53

Exterior dimensions Height × Width × Depth

mm

Unit 270 × 840 × 840 Panel 30 × 950 × 950

845 × 970 × 370

Net weight kg 31 (Unit:24 Panel:7) 74 Refrigerant equipment

Compressor type & Q’ty

–

RM-B5125MDE21 × 1

Starting method – Direct line start

Heat exchanger

Louver fin & inner grooved tubing Straight fin & inner grooved tubing

Refrigerant control – Electronic expansion valve

Refrigerant R410A

Quantity kg –

3.8 [Pre-charged up to the piping length of 30m]

Refrigerant oil

r

–

0.7 (M-MA68)

Defrost control Microcomputer controlled de-icer

Air handling equipment

Fan type & Q’ty

Turbo fan × 1 Propeller fan × 1

Motor W 20 × 1120 × 1 Starting method Direct line start Direct line start

Air ﬂ ow CMM

Powerful mode Hi:20 Me:17 Lo:15

Mild mode Hi:17 Me:15 Lo:13

Cooling: 75, Heating: 73

Outside air intake

Available – Air filter, Q’ty Plastic net (washable) × 1 – Shock & vibration absorber Rubber sleeve (for fan motor) Rubber mount (for compressor) Electric heater W – 20 (Crank case heater)

Operation control

Operation switch

Wired remote control switch (Optional : RC-E1R)

Wireless kit (Optional : RCN-T-35W-ER)

– (Indoor unit side)

Room temperature control Thermostat by electronics –

Safety equipment

Internal thermostat for fan motor.

Frost protection thermostat.

Internal thermostat for fan motor.

Anomalous discharge temperature protection.

Installation data Refrigerant piping size

Liquid line

mm

(in)

Indoor branch pipe, Outdoor main pipe: φ9.52 (3/8″)

Gas line Indoor branch pipe, Outdoor main pipe: φ15.88 (5/8″)

Connecting method Flare piping

Drain hose

Connectable with VP25 (I.D. 25mm, O.D. 32mm) – Insulation for piping Necessary (both Liquid & Gas lines) Accessories Mounting kit. Drain hose Optional parts Decorative Panel (T-PSA-35W-ER)

Notes (1) The data are measured at the following conditions.

Item

Operation

Indoor air temperature Outdoor air temperature

Standards

DB WB DB WB

Cooling 27˚C 19˚C 35˚C 24˚C

ISO-T1

Heating 20˚C – 7˚C 6˚C

(2) This packaged air-conditioner is manufactured and tested in conformity with the following standard. ISO-T1 “UNITARY AIR-CONDITIONERS” (3) The operation data indicate when the air-conditioner is operated at 230V 50Hz or 220V 60Hz. (4) Values in [ ~ ] show the minimum to maximum range. (5) Indoor unit specifications show the specifications for one unit. Capacity and running characteristics values are shown for the case where two indoor

units are combined and run together.

-

28

-

Model FDTVA602HESP2R (Indoor unit: 2 units, Outdoor unit: 1 unit)

Model

Item

FDTVA602HESP2R

FDTA301R FDCVA602HESAR

Nominal cooling capacity

(1)

kW

14.0 [7.0~14.5]

Nominal heating capacity

(1)

kW

16.0 [6.3~16.5]

Power source 3 Phase, 380-415V 50Hz/380V 60Hz

Operation data

(3)

Cooling power consumption kW

4.69/4.71

Running current (Cooling) A

6.9/7.2

Power factor (Cooling) %

98/99

Heating power consumption kW

4.58/4.60

Running current (Heating) A

6.7/7.1

Power factor (Heating) %

99/98

Inrush current (L.R.A) A

5

Noise level dB(A)

Powerful mode Hi:38 Me:35 Lo:33

Mild mode Hi:35 Me:33 Lo:31

53

Exterior dimensions Height × Width × Depth

mm

Unit 270 × 840 × 840 Panel 30 × 950 × 950

845 × 970 × 370

Net weight kg 31 (Unit:24 Panel:7) 74 Refrigerant equipment

Compressor type & Q’ty

–

RM-B5125MDE31 × 1

Starting method – Direct line start

Heat exchanger

Louver fin & inner grooved tubing Straight fin & inner grooved tubing

Refrigerant control – Electronic expansion valve

Refrigerant R410A

Quantity kg –

3.8 [Pre-charged up to the piping length of 30m]

Refrigerant oil

r

–

0.7 (M-MA68)

Defrost control Microcomputer controlled de-icer

Air handling equipment

Fan type & Q’ty

Turbo fan × 1 Propeller fan × 1

Motor W 20 × 1120 × 1 Starting method Direct line start Direct line start

Air ﬂ ow CMM

Powerful mode Hi:20 Me:17 Lo:15

Mild mode Hi:17 Me:15 Lo:13

Cooling: 75, Heating: 73

Outside air intake

Available – Air filter, Q’ty Plastic net (washable) × 1 – Shock & vibration absorber Rubber sleeve (for fan motor) Rubber mount (for compressor) Electric heater W – 20 (Crank case heater)

Operation control

Operation switch

Wired remote control switch (Optional : RC-E1R)

Wireless kit (Optional : RCN-T-35W-ER)

– (Indoor unit side)

Room temperature control Thermostat by electronics –

Safety equipment

Internal thermostat for fan motor.

Frost protection thermostat.

Internal thermostat for fan motor.

Anomalous discharge temperature protection.

Installation data Refrigerant piping size

Liquid line

mm

(in)

Indoor branch pipe, Outdoor main pipe: φ9.52 (3/8″)

Gas line Indoor branch pipe, Outdoor main pipe: φ15.88 (5/8″)

Connecting method Flare piping

Drain hose

Connectable with VP25 (I.D. 25mm, O.D. 32mm) – Insulation for piping Necessary (both Liquid & Gas lines) Accessories Mounting kit. Drain hose Optional parts Decorative Panel (T-PSA-35W-ER)

Notes (1) The data are measured at the following conditions.

Item

Operation

Indoor air temperature Outdoor air temperature

Standards

DB WB DB WB

Cooling 27˚C 19˚C 35˚C 24˚C

ISO-T1

Heating 20˚C – 7˚C 6˚C

(2) This packaged air-conditioner is manufactured and tested in conformity with the following standard. ISO-T1 “UNITARY AIR-CONDITIONERS” (3) The operation data indicate when the air-conditioner is operated at 400V 50Hz or 380V 60Hz. (4) Values in [ ~ ] show the minimum to maximum range. (5) Indoor unit specifications show the specifications for one unit. Capacity and running characteristics values are shown for the case where two indoor

units are combined and run together.

-

29

-

Model FDTVA802HESP2R (Indoor unit: 2 units, Outdoor unit: 1 unit)

Model

Item

FDTVA802HESP2R

(7)

FDTA401R FDCVA802HESAR

Nominal cooling capacity

(1)

kW

20.0 [7.0~22.4]

Nominal heating capacity

(1)

kW

22.4 [7.6~25.0]

Power source 3 Phase, 380-415V 50Hz

Operation data

(3)

Cooling power consumption kW

6.60

Running current (Cooling) A

9.9

Power factor (Cooling) %

96

Heating power consumption kW

6.46

Running current (Heating) A

9.8

Power factor (Heating) %

95

Inrush current (L.R.A) A

5

Noise level dB(A)

Powerful mode Hi:46 Me:43 Lo:41

Mild mode Hi:43 Me:41 Lo:38

57

Exterior dimensions Height × Width × Depth

mm

Unit 295 × 840 × 840 Panel 35 × 950 × 950

1300 × 970 × 370

Net weight kg 33 (Unit:26 Panel:7) 122 Refrigerant equipment

Compressor type & Q’ty

–

GT-C5150ND79 × 1

Starting method – Direct line start

Heat exchanger

Louver fin & inner grooved tubing Straight fin & inner grooved tubing

Refrigerant control – Electronic expansion valve

Refrigerant R410A

Quantity kg –

5.4 [Pre-charged up to the piping length of 30m]

Refrigerant oil

r

–

1.45 (M-MA32R)

Defrost control Microcomputer controlled de-icer

Air handling equipment

Fan type & Q’ty

Turbo fan × 1 Propeller fan × 2

Motor W 40 × 1120 × 2 Starting method Direct line start Direct line start

Air ﬂ ow CMM

Powerful mode Hi:25 Me:22 Lo:20

Mild mode Hi:22 Me:20 Lo:18

Cooling: 150, Heating: 145

Outside air intake

Available – Air filter, Q’ty Plastic net (washable) × 1 – Shock & vibration absorber Rubber sleeve (for fan motor) Rubber mount (for compressor) Electric heater W – 40 (Crank case heater)

Operation control

Operation switch

Wired remote control switch (Optional : RC-E1R)

Wireless kit (Optional : RCN-T-35W-ER)

– (Indoor unit side)

Room temperature control Thermostat by electronics –

Safety equipment

Internal thermostat for fan motor.

Frost protection thermostat.

Internal thermostat for fan motor.

Anomalous discharge temperature protection.

Installation data Refrigerant piping size

Liquid line

mm

(in)

Indoor branch pipe, Outdoor main pipe: φ9.52 (3/8″)

Gas line

(6)

Indoor branch pipe: φ15.88 (5/8″), Outdoor main pipe: φ25.4 (1″)

Connecting method Flare piping (Outdoor gas piping: Brazing)

Drain hose

Connectable with VP25 (I.D. 25mm, O.D. 32mm) – Insulation for piping Necessary (both Liquid & Gas lines) Accessories Mounting kit. Drain hose, Reducer kit (Please see page 218), Accessory pipe (Please see page 220) Optional parts Decorative Panel (T-PSA-35W-ER)

Notes (1) The data are measured at the following conditions.

Item

Operation

Indoor air temperature Outdoor air temperature

Standards

DB WB DB WB

Cooling 27˚C 19˚C 35˚C 24˚C

ISO-T1

Heating 20˚C – 7˚C 6˚C

(2) This packaged air-conditioner is manufactured and tested in conformity with the following standard. ISO-T1 “UNITARY AIR-CONDITIONERS” (3) The operation data indicate when the air-conditioner is operated at 400V 50Hz. (4) Values in [ ~ ] show the minimum to maximum range. (5) Indoor unit specifications show the specifications for one unit. Capacity and running characteristics values are shown for the case where two indoor

units are combined and run together. (6) Be sure to use the accessory pipe to connect service valve on the gas side with the ﬁ eld pipe.(Refer to the 220 page). (7) Not available in 60Hz.

Mitsubishi Heavy Industries FDTVA151HEN1R, FDTCVA151HEN1R, FDTCVA201HEN1R, FDTCVA302HENP1R, FDTCVA402HENP2R Technical Manual

Specifications and Main Features

Frequently Asked Questions

User Manual