Datasheet PSS15S92F6-AG DataSheet (Mitsubishi Electric)

PSS15S92F6-AG

With temperature output function

PSS15S92E6-AG

With OT protection function

V

(2)

V

(3)

V

(4)

W(21)

VP(6)

WP(7)

UP(5)

VP1(8)

IGBT1

IGBT2

IGBT3

Di1

Di2

Di3

VNC(9)

UN(10)

VN(11)

WN(12)

FO(14)

VN1(13)

VNC(16)

NW(18)

CIN(15)

IGBT4

IGBT5

IGBT6

Di4

Di5

Di6

NU(20)

NV(19)

LVIC

HVIC

V(22)

U(23)

P(24)

VOT(17)

·Built-in temperature output type: VOT

·

E

< Dual-In-Line Package Intelligent Power Module >

PSS15S92F6-AG
PSS15S92E6-AG

TRANSFER MOLDING TYPE
INSULATED TYPE

OUTLINE

MAIN FUNCTION AND RATINGS

 3 phase DC/AC inverter
 600V / 15A (CSTBT)
 N-side IGBT open emitter
 Built-in bootstrap diodes with current limiting resistor

APPLICATION

 AC 100~240Vrms(DC voltage:400V or below) class

low power motor control

TYPE NAME

INTEGRATED DRIVE, PROTECTION AND SYSTEM CONTROL FUNCTIONS

● For P-side : Drive circuit, High voltage high-speed level shift ing , C ontr ol supp ly under-voltage (UV) protection

● For N-side :

Drive circuit, Control supply under-voltage prote cti on (UV), Short circuit protection (SC),

Over temperature protection (OT, PSS15S92E6-AG only)

● Fault signaling : Corresponding to SC fault (N-side IGBT), UV fault (N-side supply) and OT fault

● Temperature output : Outputting LVIC temperature by analog signal (PSS15S92F

6-AG only)

● Input interface : 3, 5V line, Schmitt trigger receiver circuit (High Active)

● UL Recognized : UL1557 File E323585

INTERNAL CIRCUIT

UFB

VFB

WFB

(PSS**S92F6-AG)

Built-in OT type: NC (No Connection)

(PSS**S92

Publication Date : October 2013

6-AG)

1

< Dual-In-Line Package Intelligent Power Module >

INVERTER PART

Symbol Parameter Condition

Ratings

Unit

V

CC

Supply voltage

Applied between P-NU,NV,NW

450

V

±ICP

Each IGBT collector current (peak)

T

C

= 25°C, less than 1ms

30

A

PC

Collector dissipation

TC= 25°C, per 1 chip

27.0

W

Tj

Junction temperature

(Note 1)

-30~+150

°C

Note1: Th e maximum junc tion tempe rature rati ng of built-in power chips is 150°C(@Tc≤100°C).However, to ensure safe operation of DIPIPM, the average

junction temperature should be limited to Tj(Ave)≤125°C (@Tc≤100°C).

CONTROL (PROTECTION) PART

Symbol Parameter Condition

Ratings

Unit

VD

Control supply voltage

Applied between

VP1-VNC, VN1-VNC

20

V

V

U

VFO

Fault output supply voltage

Applied between

FO-VNC

-0.5~VD+0.5

V

IFO

Fault output current

Sink current at FO terminal

1

mA

VSC

Current sensing input voltage

Applied between CIN-VNC

-0.5~VD+0.5

V

TOTAL SYSTEM

Symbol Parameter Condition

Ratings

Unit

Self protection supply voltage limit
(Short circuit protection capability)

VD = 13.5~16.5V, Inverter Part
Tj = 125°C, non-repetitive, less than 2μs

60Hz, Sinusoidal, AC 1min, between connected all pins
and heat sink plate

THERMAL RESISTANCE

Limits

Min.

Typ.

Max.

R

th(j-c)Q

Junction to case thermal
resistance (Note 2)

Inverter IGBT part (per 1/6 module)

- - 3.7

K/W

R

th(j-c)F

Inverter FWDi part (per 1/6 module)

- - 4.5

K/W

Control terminals

DIPIPM

Tc point

IGBT chip position

Heat sink side

11.6mm

Power terminals

PSS15S92F6-AG, PSS15S92E6-AG

TRANSFER MOLDING TYPE
INSULATED TYPE

MAXIMUM RATINGS (T

= 25°C, unless otherwise noted)

j

V

CC(surge)

V

CES

Supply voltage (surge) Applied between P-NU,NV,NW 500 V

Collector-emitter voltage 600 V

±IC Each IGBT collector current TC= 25°C 15 A

VDB Control supply voltage Applied between
VIN Input voltage Applied between

V

CC(PROT)

-U, V

-V, V

UFB

VFB

, VP, WP-VPC, UN, VN, WN-VNC -0.5~VD+0.5 V

P

-W 20 V

WFB

400 V

TC Module case operation temperature Measurement point of Tc is provided in Fig.1 -30~+100 °C
T

Storage temperature -40~+125 °C

stg

V

Isol ation vol tage

iso

1500 V

Fig. 1: TC MEASUREMEN T POINT

3mm

rms

Symbol Parameter Condition

Note 2: Grease with goo d thermal c onductivi ty and long -term end urance sho uld be applied evenly with about +100μm~+200μm on the contacting surface of

DIPIPM and heat sink. The contacting therm al res istanc e bet ween D IPIP M case an d heat sink Rth( c-f) is d eterm ined by th e thick ness a nd the t herm al
conductivity of the applied grease. For reference, Rth(c-f) is about 0.3K/W (per 1/6 module, grease thickness: 20μm, thermal conductivity: 1.0W /m•K).

Publication Date : October 2013

2

Unit

< Dual-In-Line Package Intelligent Power Module >

ELECTRICAL CHARACTERISTICS
INVERTER PART

Min.

Typ.

Max.

IC= 15A, Tj= 25°C

-

1.70

2.05

IC= 15A, Tj= 125°C

-

1.90

2.25

IC=1.5A, Tj= 25°C

-

0.90

1.10

VEC

FWDi forward voltage

VIN= 0V, -IC= 15A

-

2.50

3.00

V

t

off

- 1.15

1.60

μs

t

C(off)

- 0.15

0.30

μs trr - 0.30 - μs

Tj= 25°C

- - 1

Tj= 125°C

- - 10

CONTROL (PROTECTION) PART

Limits

Min.

Typ.

Max.

VD=15V, VIN=0V

- - 2.80

VD=VDB=15V, VIN=5V

- - 0.10

V

SC(ref)

Short circuit trip level

VD = 15V

0.455

0.480

0.505

V

UV

DBt

Trip level

7.0

10.0

12.0

V

UV

DBr

Reset level

7.0

10.0

12.0

V

UVDt

Trip level

10.3 - 12.5

V

LVIC Temperature=90°C

LVIC Temperature=25°C

0.88

1.13

1.39

V

OTt

VD = 15V

Trip level

100

120

140

°C

OTrh

Detect LVIC temperature

Hysteresis of trip-reset

-

10 - °C

V

FOH

VSC = 0V, FO terminal pulled up to 5V by 10kΩ

4.9 - -

V

IIN

Input current

VIN = 5V

0.70

1.00

1.50

mA

V

th(on)

ON threshold voltage

-

2.10

2.60

V

th(off)

OFF threshold voltage

0.80

1.30

-

ON/OFF threshold
hysteresis voltage

R

Built-in limiting resistance

Included in bootstrap Di

80

100

120

Ω

0

20

40

60

80

100

120

140

160

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

VF [V]

I

F

[mA]

0

5

10

15

20

25

30

0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5

VF [V]

I

F

[mA]

PSS15S92F6-AG, PSS15S92E6-AG

TRANSFER MOLDING TYPE
INSULATED TYPE

(Tj = 25°C, unless otherwise noted)

Symbol Parameter Condition

V

ton
t

C(on)

CE(sat)

Collector-emitter saturation
voltage

VD=VDB = 15V, VIN= 5V

0.65 1.05 1.45 μs

- 0.40 0.65 μs
Switching times

V

= 300V, VD= VDB= 15V

CC

= 15A, Tj= 125°C, VIN= 0↔5V

I

C

Limits

Unit

Inductive Load (upper-lower arm)

I

CES

Symbol Parameter Condition

ID

IDB

Collector-emitter cut-off
current

Circuit current

VCE=V

CES

Total of VP1-VNC, VN1-VNC

WFB

-W

UFB

-U,

Each part of V
V

-V, V

VFB

VD=15V, VIN=5V - - 2.80

= 15V, VIN=0V - - 0.10

V

D=VDB

(Note 3)

mA

Unit

mA

P-side Control supply
under-voltage protection(UV)

N-side Control supply

UVDr Reset level 10.8 - 13.0 V
VOT

under-voltage protection(UV)
Temperature Output

(PSS**S92F6-AG)

T

≤125°C

j

Pull down R=5kΩ

(Note 4)

2.63 2.77 2.91 V

Over temperature protection

(OT, PSS**S92E6-AG) (Note5)

V

V

FOL

Fault output voltage

VSC = 1V, IFO = 1mA - - 0.95 V

tFO Fault output pulse width

V

th(hys)

VF Bootstrap Di forward voltage

Note 3 : SC protection works only for N-side IGBT. Please select the external shunt resistance such that the SC trip-level is less than 1.7 times of the current rating.

Note 4 : DIPIPM don't shutdown IGBTs and output fault signal automatically when temperature rises excessively. When temperature exceeds the protective level that

user defined, controller (MCU) should stop the DIPIPM. Temperature of LVIC vs. V

5 : When the LVIC temperature exceeds OT trip temper ature level( OT

loosely, don't reuse that DIPIPM. (There is a possibility that junction temperature of power chips exceeded maximum Tj(150°C).

6 : F ault signal Fo outputs when SC, UV or OT protection works. Fo p ulse wi dth is differen t for eac h protec tion modes. At SC failure, Fo pulse width is a fi xed

width (=minimum 20μs), but at UV or OT fail ur e, Fo out pu ts continuously until recovering from UV or OT state. (But minimum Fo pulse width is 20μs.)

7 : The characteristics of bootstrap Di is described in Fig.2.

Fig. 2 Characteristics of bootstrap Di VF-IF curve (@Ta=25°C) including voltage drop by limiting resistor (Right chart is enlarged chart.)

Publication Date : October 2013

Applied between UP, VP, WP, UN, VN, WN-VNC

IF=10mA including voltage drop by limiting resistor

output characteristics is described in Fig. 3.

), OT protection works and Fo outputs. In that case if the heat sink dropped off or fixed

t

OT

3

(Note 6)

(Note 7)

20 - - μs

V

0.35 0.65 -

1.1 1.7 2.3 V

< Dual-In-Line Package Intelligent Power Module >

2.77

2.63

2.91

1.6

1.8

2.0

2.2

2.4

2.6

2.8

3.0

3.2

3.4

3.6

3.8

4.0

60 70 80 90 100 110 120

LVIC temperature (°C)

V

OT

output (V)_

Typ.

Max.

Min.

Ref

VOT

Temperature
Signal

VNC

Inside LVIC
of DIPIPM

5kΩ

PSS15S92F6-AG, PSS15S92E6-AG

TRANSFER MOLDING TYPE
INSULATED TYPE

Fig. 3 Temperature of LVIC vs. VOT output characteristics

Fig. 4 VOT output circuit

(1) It is recommended to insert 5kΩ (5.1kΩ is recommended) pull down resistor for getting linear output charact eristics at low temperature

below room temperature. When the pull dow n resistor is inserted between V
calculated approximately by V
using V

(2) In the case of using V

temperature rises excessively. If system uses low voltage controller, it is recommended to insert a clamp Di between control supply of
the controller and V

(3) In the case of not using V

Refer the application note for Super Mini DIPIPM Ver.5 series about the usage of V

and VNC(control GND), the extra circuit current, which is

output voltage divided by pull down resistance, flows as LVIC circuit current continuously. In the case of

for detecting high temperature over room temperature only, it is unnecessary to insert the pull down resist or.

OT

OT

OT

with low voltage controller like 3.3V MCU, VOT output might exceed control supply voltage 3.3V when

OT

output for preventing over voltage destruction.

, leave VOT output NC (No Connection).

OT

OT

.

OT

MCU

Publication Date : October 2013

4

< Dual-In-Line Package Intelligent Power Module >

MECHANICAL CHARACTERISTICS AND RATINGS

Limits

Min.

Typ.

Max.

Mounting torque

Mounting screw : M3

Recommended 0.69N·m

0.59

0.69

0.78

N·m

Control terminal: Load 4.9N
Power terminal: Load 9.8N

Control terminal: Load 2.45N
90deg. bend

Weight

-

8.5 - g

Heat-sink flatness

-50 - 100

μm

RECOMMENDED OPERATION CONDITIONS

Limits

Min.

Typ.

Max.

VCC

Supply voltage

Applied between P-NU, NV, NW

0

300

400

V

ΔVD, ΔVDB

Control supply variation

-1 - +1

V/μs

t

dead

Arm shoot-through blocking time

For each input signal

1.0 - -

μs

f

PWM

PWM input frequency

TC ≤ 100°C, Tj ≤ 125°C

- - 20

kHz

VCC = 300V, VD = 15V, P.F = 0.8,

PWIN(on)

0.7 - -

4.6mm

-

+
Heat sink side

Heat sink side

Measurement position

17.5mm
+

-

PSS15S92F6-AG, PSS15S92E6-AG

TRANSFER MOLDING TYPE
INSULATED TYPE

Parameter Condition

Terminal pulling strength

Terminal bending strength

Note 8: Plain washers (ISO 7089~7094) are recommended.
Note 9: Measurement point of heat sink flatness

Power terminal: Load 4.9N

(Note 8)

Unit

EIAJ-ED-4701 10 - - s

EIAJ-ED-4701 2 - - times

(Note 9)

Symbol Parameter Condition

VD Control supply voltage Applied between VP1-VNC, VN1-VNC 13.5 15.0 16.5 V
VDB Control supply voltage Applied between V

IO Allowable r.m.s. current

PWIN(off) 0.7 - -

Minimum input pulse width

Sinusoidal PWM
T

≤ 100°C, Tj ≤ 125°C (Note10)

C

UFB

-U, V

VFB

-V, V

-W 13.0 15.0 18.5 V

WFB

= 5kHz - - 7.5

f

PWM

f

= 15kHz - - 4.5

PWM

(Note 11)

VNC VNC variation Between VNC-NU, NV, NW (including surge) -5.0 - +5.0
Tj Junction temperature -20 - +125 °C

Note 10: Allowable r.m.s. current depends on the actual application conditions.

11: DIPIPM might not make response if the input signal pulse width is less than PWIN(on), PWIN(off).

Unit

Arms

μs

V

Publication Date : October 2013

5

< Dual-In-Line Package Intelligent Power Module >

Lower-side control
input

Protection circuit state

Internal IGBT gate

Output current Ic

Sense voltage of
the

Error output Fo

SC

a2

SET

RESET

SC

a1

a3

a6

a7

a4

a8

a5

D

RESET

SET

RESET

UVDt

b1

b2
b3

b4
b6

b7

b5

Control input

Protection circuit state

Control supply voltage VD

Output current Ic

Error output Fo

PSS15S92F6-AG, PSS15S92E6-AG

TRANSFER MOLDING TYPE
INSULATED TYPE

Fig. 5 Timing Charts of The DIPIPM Protective Functions
[A] Short-Circuit Protection (N-side only with the external shunt resistor and RC filter)

a1. Normal operation: IGBT ON and outputs current.
a2. Short circuit current detection (SC trigger)

(It is recommended to set RC time constant 1.5~2.0μs so that IGBT shut down within 2.0μs when SC.)
a3. All N-side IGBT's gates are hard interrupted.
a4. All N-side IGBTs turn OFF.
a5. F

outputs for tFo=minimum 20μs.

O

a6. Input = “L”: IGBT OFF
a7. Fo finishes output, but IGBTs don't turn on until inputting next ON signal (LH).

(IGBT of each phase can return to normal state by inputting ON signal to each phase.)

a8. Normal operation: IGBT ON and outputs current.

trip current level

shunt resistor

[B] Under-Voltage Protection (N-side, UV

b1. Control supply voltage V

(IGBT of each phase can return to normal state by inputting ON signal to each phase.)
b2. Normal operation: IGBT ON and outputs current.
b3. V

level drops to under voltage trip level. (UVDt).

D

b4. All N-side IGBTs turn OFF in spite of control input condition.
b5. Fo outputs for t
b6. V

level reaches UVDr.

D

b7. Normal operation: IGBT ON and outputs current.

=minimum 20μs, but output is extended during VD keeps below UVDr.

Fo

exceeds under voltage reset level (UVDr), but IGBT turns ON by next ON signal (LH).

D

)

D

UVDr

reference voltage

elay by RC filtering

Publication Date : October 2013

6

< Dual-In-Line Package Intelligent Power Module >

Control input

Protection circuit state

Control supply voltage VDB

Output current Ic

Error output Fo

UV

RESET

SET

RESET

UV

Keep High-level (no fault output)

c1

c2
c3

c4

c5

c6

SET

RESET

OTt

d1

d2

d3
d5

d6

d4

OTt - OT

Control input

Protection circuit state

Temperature of LVIC

Output current Ic

Error output Fo

PSS15S92F6-AG, PSS15S92E6-AG

TRANSFER MOLDING TYPE
INSULATED TYPE

[C] Under-Voltage Protection (P-side, UVDB)

c1. Control supply voltage VDB rises. After the voltage reaches under voltage reset level UV
c2. Normal operation: IGBT ON and outputs current.
c3. V

level drops to under voltage trip level (UV

DB

DBt

).
c4. IGBT of the correspond phase only turns OFF in spite of control input signal level, but there is no F
c5. V

level reaches UV

DB

DBr

.

c6. Normal operation: IGBT ON and outputs current.

DBr

DBt

[D] Over Temperature Protection (N-side, Detecting LVIC temperature)

d1. Normal operation: IGBT ON and outputs current.
d2. LVIC temperature exceeds over temperature trip level(OT
d3. All N-side IGBTs turn OFF in spite of control input condition.
d4. Fo outputs for t

=minimum 20μs, but output is extended during LVIC temperature keeps over OTt.

Fo

d5. LVIC temperature drops to over temperature reset level.
d6. Normal operation: IGBT turns on by next ON signal (LH).

(IGBT of each phase can return to normal state by inputting ON signal to each phase.)

).

t

, IGBT turns on by next ON signal (LH).

DBr

rh

signal output.

O

Publication Date : October 2013

7

< Dual-In-Line Package Intelligent Power Module >

D1 + +

MCU

C2

15V VD

M

C4

R1

Shunt
N1 B C

5V A C2

V

(2)

V

(3)

V

(4)

+

UN(10)

VN(11)

WN(12)

Fo(14)

VN1(13)

VNC(16)

P(24)

U(23)

W(21)

LVIC

V(22)

VP(6)

WP(7)

UP(5)

VP1(8)

CIN(15)

IGBT1

IGBT2

IGBT3

Di1

Di2

Di3

C1

C1

C2 + D

D1

VNC(9)

C3

HVIC

NW(18)

IGBT4

IGBT5

IGBT6

Di4

Di5

Di6

NU(20)

NV(19)

Power GND wiring

Control GND wiring

VOT(17)

5kΩ

Long GND wiring here might

Long wiring here might cause SC
level fluctuation and malfunction.

Long wiring here might
cause short circuit failure

Bootstrap negative electrodes
terminals directly and separated

Built-in temperature

+

PSS15S92F6-AG, PSS15S92E6-AG

TRANSFER MOLDING TYPE
INSULATED TYPE

Fig. 6 Example of Applicatio n Circuit

UFB

VFB

WFB

output type only
(PSS**S92F6-AG)

generate noise to input signal and

(1) If control GND is connected with power GND by c om m on broad pattern, it may cause malfunction by power G N D fluctuation.

It is recommended to connec t control GND and power GND at only a point N1 (near the terminal of shunt resistor).
(2) It is recommended t o insert a Zener diode D1(24V/1W) between each pair of control supply terminals to prevent surge destruction.
(3) To prevent surge destruction, the wiring between the smoothing capacitor and the P, N1 terminals should be as short as possible.

Generally a 0.1-0.22μF snubber capacitor C3 between the P-N1 terminals is recommended.
(4) R1, C4 of RC filter for preventi ng protection c ircuit malfunc tion is r ecommended to selec t tight toler ance, temp-com pensated type.

The time constant R1C4 should be set so that SC current is shut down within 2μs. (1.5μs~2μs is general value.) SC interrupting time

might vary with the wiring pattern, so the enoug h evaluation on the real system is necessary.
(5) To prevent malfunct ion, the wiring of A, B, C should be as shor t as possible.
(6) The point D at which t he wi ri ng to CI N fi l ter i s divi ded shoul d be near t he terminal of shunt res i stor. NU, NV, NW terminals should be

connected at near N U, NV, NW terminals.
(7) All capacitors s hould be mounte d as cl ose to the ter minals as possible. (C1: good t emperature, frequenc y characteristic electrolytic

type and C2:0.22μ-2μF, good temperature, frequency and DC bias characteristic cer am ic type are recommended.)
(8) Input drive is Hi gh-active type. There is a minimum 3.3kΩ pull-down resistor in the input circuit of IC. To prevent malfunction, the

wiring of each input should be as short as possible. When using RC coupling circuit, make sure the input signal level meet the turn-on

and turn-off threshold voltage.
(9) Fo output is open drain type. It should be pul led up to MCU or control power supply ( e.g. 5V,15V) by a resistor that makes I

1mA. (I

is estimated roughly by the formula of control power supply voltage divided by pull-up resistance. In the case of pulled up to

FO

5V, 10kΩ (5kΩ or more) is recommended.)
(10) Thanks to built-in HVIC, direct coupling to MC U w ithout any opto-coupl er or transformer isolation is possible.
(11) Two V

termi nals (9 & 16 pin) are connected i nside DIP IPM, please c onnect eit her one to the 15V pow er supply G ND outside and

NC

leave another one open.
(12) If high frequency noise superimposed to the control supply line, IC malfunction might happen and cause DIPIPM erroneous operation.

To avoid such problem, line ripple voltage shoul d meet dV/dt ≤+/-1V/μs, Vripple≤2Vp-p.
(13) For DIPIPM, it isn't recommended to drive same load by parallel connection w ith other phase IGBT or other DIPIPM.

should be connected to U,V,W
from the main output wires

resistor

up to

Fo

Publication Date : October 2013

8

UP,VP,WP,UN,VN,WN

Fo

VNC(Logic)

DIPIPM

MCU

10kΩ

5V line

3.3kΩ(min)

Note)

Wiring Inductance should be less than 10nH.

Inductance of a copper pattern with

NU, NV, NW should be connected

N1

VNC

NU
NW

DIPIPM

VNC

GND wiring fr o m VNC should

connected close to the

terminal of shunt resistor.

Shunt
resistor

DIPIPM

NU

N1

GND wiring fro m VNC should

connected close to the

terminal of shunt resistor.

Shunt

Each wiring Inductance should be less than 10nH.

Inductance of a copper pattern with
length=17mm, width=3mm is about 10nH.

P V U

W

N-side IGBT

P-side IGBT

Drive circuit

VNC

NW

Drive circuit

CIN

NV

NU

-

Vref + Vref

Vref

Comparators
(Open collector output type)

External protection circuit

Protection circuit

Shunt
resistors

5V

B A C

OR output

D

N1

-

+

-

+

< Dual-In-Line Package Intelligent Power Module >

PSS15S92F6-AG, PSS15S92E6-AG

TRANSFER MOLDING TYPE
INSULATED TYPE

Fig. 7 MCU I/O Interface Circuit

Fig. 8 Pattern Wiring Around the Shunt Resistor

each other at near terminals.

length=17mm, width=3mm is about 10nH.

NV
NW

be

Low inductance shunt resistor like surface mounted (SMD) type is recommended.

Fig. 9 Pattern Wiring Around the Shunt Resistor (for the case of open emitter)

When DIPIPM is operated with three shunt resistors, voltage of each shunt resistor cannot be input to CIN terminal directly. In that case, it is necessary to use

the external protection circ ui t as below.

DIPIPM

Rf

Cf

(1) It is necessary to set the time constant R

SC interrupting time might vary with the wiring pattern, comparator speed and so on.

of external comparator input so that IGBT stops within 2μs when short circuit occurs.

fCf

(2) It is recommended for the threshold voltage Vref to set to the same rating of short circuit trip level (Vsc(ref): typ. 0.48V).
(3) Select the exter nal shu nt res is tance so that SC trip-level is less than specifie d value (=1.7 times of rating current).
(4) To avoid malfunction, the wiring A, B, C should be as short as possible.
(5) The point D at which the wiring to comparator is divided should be close to the terminal of shunt resistor.
(6) OR output high level when pr ote c tio n w ork s should be over 0.505V (=maximum Vsc(ref) rating).

Design for input RC filter depe nds on PW M control s cheme used

in the application and wiring impedance of the printed circuit board.

DIPIPM input signal interface integrates a minimum 3.3kΩ
pull-down resistor. Therefore, when inserting RC filter, it is
necessary to satisfy turn-on threshold voltage requirement.

Fo output is open d rain type. It should be pulled up to control
power supply (e.g. 5V, 15V) with a resistor that makes Fo sink
current I
（5kΩ or more） is recommended.

1mA or less. In the case of pulled up to 5V supply, 10kΩ

Fo

NV

resistors

be

Publication Date : October 2013

9

< Dual-In-Line Package Intelligent Power Module >

1-A

NC(VNC)

1-B

NC(VP1)

2

V

UFB

3 V

VFB

4 V

WFB

5 UP 6 VP 7 WP 8 VP1 9 VNC *1

10

UN

11

VN

12

WN

13

VN1

14

Fo

15

CIN

16

VNC *1

17

NC / V

OT

*2

18

NW

19

NV

20

NU

21 W 22 V 23 U 24 P 25

NC

PSS15S92F6-AG, PSS15S92E6-AG

TRANSFER MOLDING TYPE
INSULATED TYPE

Fig. 10 Package Outlines

PSS**S92F6-AG, PSS**S92E6-AG

Dimensions in mm

TERMINAL CODE

1) 9 & 16 pins (VNC) are connected inside DIPIPM, please connect either one to the control power supply GND outside and leave another one open.

2) No.17 is V

for built-in temperature out put f u ncti o n type (PSS**S92F6-AG) and NC (No Connection) for built-in OT protection function type (PSS**S92E6-AG).

OT

QR Code is registered trademark of DENSO WAVE INCORPORATED in JAPAN and other countries.

Publication Date : October 2013

10

< Dual-In-Line Package Intelligent Power Module >

1

10/15/2013

-

New

PSS15S92F6-AG, PSS15S92E6-AG

TRANSFER MOLDING TYPE
INSULATED TYPE

Revision Record

Rev. Date Page Revised c ontents

Publication Date : October 2013

11

< Dual-In-Line Package Intelligent Power Module >

Keep safety first in your cir c uit des igns!

reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors
making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary

Notes regarding these ma t er ials

These materials are intended as a reference to assist our customers in the selection of the Mitsubishi

Mitsubishi Electric Corporation assumes no responsibility for any damage, or infringement of any

All information contained in these materials, including product data, diagrams, charts, programs and

Mitsubishi Electric Corpor ation witho ut notice d ue to product impr ovement s or other reasons. I t

ic Corporation or an authorized

Electric Corporation assumes no responsibility for any damage, liability, or other loss rising from these
Please also pay attention to information published by Mitsubishi Electric Corporation by various means,

When using any or all of the information contained in these materials, including product data, diagrams,

he information and products. Mitsubishi Electric Corporation assumes

system that is used under circumstances in which human life is potentially at stake. Please contact

Corporation or an authorized Mitsubishi Semiconductor product distributor when

contained herein for any specific purposes, such as apparatus or systems

If these products or technologies are subject to the Japanese export control restrictions, they must be

export contrary to the export control laws and regulations of Japan and/or the country of

PSS15S92F6-AG, PSS15S92E6-AG

TRANSFER MOLDING TYPE
INSULATED TYPE

Mitsubishi Electric Cor por ation put s the m ax imum ef fort into ma king se micon duct or pr oduct s bett er and mor e
may lead to personal injury, fire or property damage. Remember to give due consideration to safety when
circuits, (ii) use of non-flammable material or (iii) prevention against any malfunctio n or mishap.

•
semiconductor product best suited to the customer’s application; they do not convey any license under any
intellectual property rights, or any other right s, belonging to Mitsubishi Ele ct r ic Corporation or a third party.

•
third-party’s rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or
circuit application exam pl es contained in these mater ia ls.

•
algorithms represents information on products at the time of publication of these materials, and are subject
to change by
is therefore recommended that customers contact Mitsubishi Electr
Mitsubishi Semiconductor product distributor for the latest product information before purchasing a product
listed herein.
The information described here may contain technical inaccuracies or typographical errors. Mitsubishi

inaccuracies or errors.
including the Mitsubi s hi Semiconductor home page (http://www.MitsubishiElectric.com/).

•
charts, programs, and alg orithms, ple ase be sure to ev aluate all informat ion as a tot al system before making
a final decision on the applicability of t
no responsibility for any dam age, l iability or other loss resulting from the information contained herein.

•Mitsubishi Electric Corporation semiconductors are not designed or manufactured for use in a device or
Mitsubishi Electric

considering the use of a product
for transportation, vehicular , medical, aerospace, nuc le ar, or undersea repeater use.

•The prior written approval of Mitsubishi Electric Corporation is necessary to reprint or reproduce in wh ole or
in part these materials.

•
exported under a license from the Japanese government and cannot be imported into a country other than
the approved destination.
Any diversion or re­destination is prohibited.

•Please contact Mit su bish i Electr ic Corpor at ion or a n aut horiz ed Mit s ubish i Se mico nduct or pr oduct distributor
for further details on these materials or the product s contained therein.

© 2013 MITSUBISHI ELECTRIC CORPORAT ION. ALL RIGHTS RESERVED.
DIPIPM and CSTBT are registered trademarks of MITSUBISHI ELECTRIC CORPORATION.

Publication Date : October 2013

12