Mitsubishi VS-70705, VS-60705, VS-55705, VS-50705, VS-50605 Owner’s Manual

...

MITSUBISHI

THE BIG SCREEN COMPANY TM

RISKOF ELECTRICSHOCK DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER

(OR BACK). NO USER-SERVlCEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

/_The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert

//_ The exclamation point within an equilateral triangle is intended to alert the user to the

Warning: To avoid permanently imprinting a fixed image onto yourTV screen,pleasedo not displaythe same

stationary imageson the screen for more than 15%of your total TV viewing in one week. Examplesof stationary imagesare letterbox top/bottom barsfrom DVD disc or other video sources,side bars when showing standardTV pictures on widescreen TV's,stock market reports, video game patterns,station logs,web sitesor stationary com- puter images. Suchpatterns can unevenly agethe picture tubes causingpermanent damageto theTV. Pleaseseepage 58 for a detailed explanation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruc- tions, may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful interfer- ence to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

the user to the presence of uninsulated"dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock.

presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

• Reorient or reJocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

Changes or modifications not expressly approved by Mitsubishi could void the user's authority to operate this equipment.

WARNING: TO REDUCETHE RISKOF FIREOR ELECTRIC SHOCK, DO NOT EXPOSETHISAPPLIANCETO RAIN OR

MOISTURE.

CAUTION:

TO PREVENTELECTRIC SHOCK, MATCH WIDE BLADE OF PLUGTO WIDE SLOT,FULLYINSERT.

NOTE TO CATV SYSTEM INSTALLER:

THIS REMINDER IS PROVIDEDTO CALLTHE CATV SYSTEMINSTALLER'SATTENTION TO ARTICLE 820-40 OF THE NEC THAT PROVIDESGUIDELINES FOR PROPERGROUNDING AND, IN PARTICULAR, SPECIFIESTHAT

THE CABLE GROUND SHALL BECONNECTEDTOTHE GROUNDING SYSTEMOFTHE BUILDING,AS CLOSE TOTHE POINT OF CABLE ENTRYAS PRACTICAL.

Contents

Important Safeguards 5

Instructions on safety and proper handling of your Mitsubishi television

Special Features 7

Distinctive features, items included with your Mitsubishi television and hookup guidelines

Shortcuts 8

A quick reference list

Connections 9

Basichookups to an antenna, cable and components

Remote Control Functions 15

Features of the remote control, programming to work with other audio and video products,

explanation of buttons

Thel_H ° Menu System 2 I

Explanation of the on-screen menu system and the basic set-up menu screens including

Memorizing Channels, Set Clock and Day, AV Connection and On-Screen Language

Remote Control Input and Channel Selection 3 I

Changing inputs and channels and setting the sleep timer with the remote control

The Main Menu Screens 33

Explainsthe Parent Lock, Channel Edit, Advanced Features and Audio/Video Settings Menus

Special Remote Control Functions 49

How the remote works with other products includingthe Mitsubishi A/V Network, viewing

the PIP (Picture-in-Picture) and POP (Picture-outside-Picture)

Control Panel Functions 54

Explanation of the front panel buttons and the back panel terminals

Troubleshooting 57

Common problems, notes on caring and cleaning your Mitsubishi television and how to obtain service

Appendices 6 I

Diamond ShieldTM installation, remote control programming codes, bypassing the parent lock

This page is blank

Please read all these instructions regarding your television set and retain for future refer-

ence. Follow all warnings and instructions marked on the television.

I. Read, Retain and Follow Instructions

Readall safety and operating instructionsbefore operating the appliance.Retain the safety and operating instructionsfor future reference. Follow all operating and use instructions.

2. Heed Warnings

Adhere to all warnings on the applianceand in the operating instructions.

3. Cleaning

Unplug thisTV receiver from the wall outlet before cleaning. Do not useliquid or aerosol cleaners.Cleaners canpermanently damagethe cabinet or screen.Use adamp cloth for cleaning.

4. Attachments and Equipment

Never add anyattachments and/or equipment without approval of the manufacturer assuchadditions may result inthe risk of fire, electric shock or other personal injury.

5. Water and Moisture

Do not usethisTV receiver where contact with or immersioninwater is possible. Do not usenear bath

tubs, wash bowls, kitchen sinks,laundrytubs,swimming pools,etc.

6. Accessories

Do not placethis TV receiver on an unstablecart, stand,tripod, bracket, or table. TheTV receiver mayfall,

causingserious injuryto a child or adult,and serious damageto the appliance. Use only

with a cart, stand,tripod, bracket, or table recommended by the manufacturer,or sold with

theTV receiver. Any mounting of the applianceshould follow the manufacturer's instruc- tions, and should usea mounting accessory recommended by the manufacturer.

An applianceand cart combination should be moved with care. Quick stops, excessive

force, and uneven surfacesmay causethe applianceand cart combination to overturn.

7. Ventilation

Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of theTV receiver and to protect it from overheating. Do not block these openings or allow them to be blocked by

placingthe TV receiver on a bed, sofa,rug,or other similar surface. Nor should it be placed over a radiator or heat register. If the TV receiver isto be placed in a rack or bookcase,ensure that there is adequate

ventilation and that the manufacturer's instructionshave been adhered to.

8. Power Source

This TV receiver should be operated only from the type of power source indicatedon the marking label. If you are not sure of the type of power supplied to your home, consult your appliancedealer or local power

company.

9. Grounding or Polarization

This TV receiver isequipped with a polarized alternating current line plug having one bladewider than the

other. This plug will fit into the power outlet only one way. If you are unableto insertthe plug fully intothe outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet Do not defeat the safety purpose of the polarized plug.

I0. Power-Cord Protection

Power-supplycords should be routed so that they are not likely to be walked on or pinched by items placed upon or againstthem, payingparticular attention to cords at plugs,convenience receptacles,and the point

where they exit from the appliance.

I I. Lightning

For added protection for thisTV receiver during a lightningstorm, or when it isleft unattendedandunused

for longperiods of time, unplug it from the wall outlet and disconnect the antennaor cable system. This will

prevent damageto theTV receiver due to lightning and power-line surges.

12. Power Lines

An outside antenna system should not be located in the vicinity of overhead power linesor other electric

light or power circuits, or where it can fail into such power linesor circuits. When installing an outside antennasystem,extreme care should be taken to keep from touching such power lines or circuits as contact

with them might be fatal.

13. Overloading Do not overload wait outlets and extension cords as this canresult ina risk of fire or electric shock.

14. Object and Liquid Entry Never push objects of anykind into this TV receiver through openingsasthey maytouch dangerousvoltage points or short-out parts that could result ina fire or electric shock. Never spill liquid of anykind on theTV

receiver.

EXAMPLE OF ANTENNA GROUNDING

15. Outdoor Antenna Grounding If an outside antennaor cablesystem isconnected to the TV receiver, be sure

LEADIN WIRE

the antenna or cable system isgrounded so asto provide some

protection againstvoltage surgesand built-up static charges. Section 810 of the National Electrical Code,ANSI/NFPA

70-1984,provides informationwith respect to proper

{NEC SECTION 810-20)

GROUNDkNG CONDUCTORS

grounding of the mast and supporting structure, grounding

of the lead inwire to an antennadischarge unlt, size of

grounding conductors, location of antennadischargeunit, con-

nection to grounding electrodes, and requirements for the

grounding electrode.

NEC -. NATkONAL ELECTRICAL CODE {NEC ART 250, PART H)

=_POWE R SERVIC E GROUNDING

ELECTRODE SYSTEM

16. Servicing

Do not attempt to service this TV receiver yourself asopening or removing covers may expose you to dangerousvoltage or other hazards. Refer all servicing to qualified service personnel.

17. Damage Requiring Service

Unplug this TV receiver from the wall outlet and refer servicing to qualified service personnel under the

following conditions:

(a)When the power-supply cord or plug is damaged. (b) If liquid has been spilled,or objects havefallen into the TV receiver.

(c) If the TV receiver hasbeen exposed to rain or water. (d) If theTV receiver does not operate normally by following the operating instructions, adjust only those

controls that are covered by the operating instructions as an improper adjustment of other controls may result in damageand will often require extensive work by a qualified technician to restore theTV receiver to itsnormal operation. (e) If theTV receiver hasbeen dropped or the cabinet has been damaged.

(f)When the TV receiver exhibits a distinct changein performance -- this indicatesa needfor service.

18. Replacement Parts

When replacement parts are required, be sure the service technician hasused replacement parts specified

by the manufacturer or havethe samecharacteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.

19. Safety Check

Upon completion of anyservice or repairs to this TV receiver,askthe service technician to perform safety checksto determine that the TV receiver is in safeoperating condition.

0 ComponentVideo Input - for the best picture from DVD players

0 DiamondShield TM- protective screen shield for modelsVS-50705,

VS-55705,VS-60705 andVS-70705

0 IRIS TM - sensor that automatically adjusts brightness and contrast, for

models VS-50705,VS-55705,VS-60705 andVS-70705

0 Multibrand Remote Control - use one remote control for many

audio video components

The following items are included with your newTV:

Remote C0ntr_

m II

The connections shown in this book are general. Cable systems as well as individual audio andlor video components can vary from those shown here. The first diagram show basic connections to antenna or cable systems. After you have completed these, you can then connect any addi-

tional components (stereo, DVD, AV receiver, etc.).

2 AAA batteries

IMPORTANT

To maximize your system for its best performance, your dealer can help you

customize hookups and sell you any additional connection accessories that

may be needed for your individual equipment.

0 Hooking up yourTV to an antenna or wall outlet cable

0 Remote control functions - pages 19-20

0 Menu screen summaries - page 22-24

0 Selecting the input - page 3 I

0 Setting theV-chip parent lock - page 33

0 Picture-in-picture mode - page 50

0 Picture-outside-picture mode

(forVS-50705,VS-55705,VS-60705 andVS-70705)

0Troubleshooting- page 57

-p_e52

- page 9

TV to Antenna orWall Outlet Cable

Separate UHF andVHF antennas

VHF Antenna UHF A_ter _a

I, Connect the UHF andVHF

antenna leads to the UHF/VHF combiner,

2, Press the combiner ontoANT-A

on theTV back panel.

Twin lead antenna or wall outlet cable

For antenna with twin fiat leads

I, Connect the 300 ohm twin leads to

the transformer.

2. Push the 75 ohm side of the trans- former onto ANT-A on theTV

back panel,

Twin Leaa

2°°.....L/

For cable or antenna with coaxial lead

Connect the incoming cable to ANT-A on the TV back panel,

_3) (Channel 14_9)

Rat TwEn Le_d F_t TW_E_L_ad 1

External

A_t_a

or Ca_

*there are different combiners for different wires.

Check with your dealer for the combiner style that you need.

30_Ognrm t°

OPTIONAL"

Bacl; Sole

fs Ohm ,

TV Back Panel

ANT.A

TV Back PaneI

00 O0

@ @@

@@ @@

%e %o

_o Ohm _ to 7_ Ohm out

Ma_r_i_g _r_ns_ormer

o o

@®@ ®@@

o_, @o®

o 6

Connection of TV to Cable Box

I, Connect the incoming cable to

ANT-A on the TV back panel.

2, Connect two coaxial cables as

follows:

• One from CABLE LOOP-OUT on theTV back panel to IN on the

back of the cable box,

• One from OUT on the back of the cable box to ANT-B on theTV

back panel,

TV Back Pane]

Incoming Ca_

Connection ofTV toVCR and Cable Box

I. Connect the incoming cable toANT-A

on theTV back panel.

TV Back Pa_e_

2. Connect three coaxial cables as follows:

• One from CABLE LOOP-OUT on the TV back panel to IN on the back of the

cable box.

• One from OUT on the back of the cable box to ANTENNA IN on the

VCR back panel.

• One from ANTENNA OUT on the VCR back panel to ANT-B on the TV

back panel.

Audio Video Connections

C_BL_

ANTAL0_O0UT A_T B

® ® @

® ® ®

®®

If your VCR has a video channel ONIOFF sw[tch_ set _tto OFF,

TV B_ck Pane

,i@

®o®

V6R Back Pa_l

I. Connect a video cable fromVIDEO

OUT on theVCR back panel toVIDEO INPUT I or INPUT 2 on theTV back

panel.

If you have a S-VHS VCR, follow the same steps, using the S-Video terminals

on the VCR and TV.

2. Connect a set of audio cables from AUDIO OUT on theVCR back panel

to AUDIO INPUT on the TV back panel. The red cable connects to the R

(right) channel and the white cable connects to the L (left). If yourVCR is non-stereo, connect only the L (left)

cable.

,@ ®

RCA

p[_ t pe

CabEe

°&

VCR Back pa_e_

If your VCR has a video channel ON/OFF switch, set it to OFF,

RCA pin t e

Attach

S-Video _ype cable

only

cablo

typ_

Connection ofTV toVCR and Antenna or

Wall Outlet Cable

Antenna/Cable Connections

I, Connect the incoming cable toANT-A

on theTV back panel,

2, Connect two coaxial cables as follows:

• One from CABLE LOOP-OUT on the TV back panel toANTENNA IN on the

VCR back panel,

• One fromVCR back panelANTENNA OUT to ANT-B on the TV back panel,

Audio/Video Connections

_T A _JTA_T

If your VCR has a video channe{

ON/OFF switch, set it to OFF,

® ® i@ii@ @

VCR Sack Panel

I. Connect a video cable fromVIDEO

OUT on theVCR back panel toVIDE@ INPUT I or INPUT 2 on theTV back

panel.

If you have a S-VHS VCR, follow the same steps, using the S-Video terminals

on the VCR and TV.

2. Connect a set of audio cables from AUDIO OUT on theVCR back panel to

AUDIO INPUT on the TV back panel. The red cable connects to the R (right)

channel and the white cable connects to the L (left). If your VCR is non-stereo,

only connect the L (left) cable.

If your VCR has a video channel

ON/OFF switch, set it to OFF

Connection of TV to Stereo Audio System

I. Connect the audio cables from AUDIO

MONITOR OUTPUT on the TV back panel toTV IN orAUX IN terminals on

the back of the audio system. The red cable connects to the R (right) channel

and the white cable connects to the L (left) channel.

2. Turn off the TV'S speakers through the AV Connection Menu (page 27).

3. Set the audio system's input to theTV or AUX position to hear the TV's audio through your stereo system.

Connection of TV to the Active A/V Network

Audio _y_Lern teat tetrn_na_

TV Back Pa_e_

of _b

o @@

To control your Mitsubishi audio and/or video products with one remote control

Connect the A/V network cable from

ACTIVE A/V NETWORK on theTV

Mi_subishiCompone£treartermJnals

back panel to IN on the back of a Mitsubishi component that hasA/V

network terminal.

TV Back Panek

® @ ®

®® ® ® ®

IMPORTANT

Check the Owner's Guide of your added Mitsubishi components to

ensure the best possible connections.

@@@

ACTWEAN

N_TWORK

Connection of TV to AV Receiver

I. Connect a video cable from VIDEO

MONITOR OUT on the back of the AV Receiver toVIDEO INPUT I on theTV

back panel using aVIDEO cable,

TV _ack paneE

2, Connect a video cable fromVIDEO

MONITOR OUTPUT on the TV back panel toVIDEOTV IN on the back of

the AV Receiver,

3, Connect a set of audio cables from

AUDIO OUTPUT on the TV back panel to AUDIOTV IN on the back of

theAV Receiver. The red cable con- nects to the R (right) channel and the

white cable connects to the L (left) channel.

F_JD-

AV RECEIVER

Connection of TV to DVD with ComponentVideo

Outputs

IMPORTANT

For Digital Audio connections, see

the Owner's Guides of your DVD

Player and AV Receiver.

For ComponentVideo Connections

I. Connect the ComponentVideo cables

from VIDEO OUT on the back of the DVD player to DVDVIDEO INPUT on

the TV back panel, matching the correct components:

• Y toY,

Cr to Cr,

Cb to Cb.

2. Connect a set of audio cables from AUDIO OUT on the back of the DVD

player to DVD AUDIO INPUT on the TV back panel. The red cable connects to the R (right) channel and the white cable connects to the L (left) channel.

TV Back Panel

I 0

DVD Rear Terminal

Warning: Don't display the same stationary images on the screen for more than 15%of your total TV viewing in one weelc Examples of stationary images are letterbox top/bottom bars from DVD disc or

other video sources, side bars when showing standard TV pictures on widescreen TV's, stock market reports, video game patterns, station logs, web sites or stationary computer images. Such patterns can unevenly age the picture tubes causing permanent damage to the TV. Please see page 58 for a detailed explanation.

For Models VS-45605 and VS-50605

Additional features of Models VS-50705, VS-55705,VS-60705

and VS-70705

REC STOP PAUSE

REW/REV FF/FWD

PLAY

_ MITSUBISHI

light

REC STOP PAUSE

REW/REV FF/FWD

pLAy

,_ MrrsuBISHI

GUIDE button

for DSSsystems

OperatingYour Remote Control

Installing the batteries

I. Remove the back cover of the remote control by pushingthe

the direction of the arrow and slidingoff the cover.

2.Load the batteries, makingsure the polarities(+) and(-) are correct.

IMPORTANT

When you replace the batteries in your remote control, the remote may return to its initial setting. You may need to set up your remote again.

For best results

Be within 20 feet of the equipment when using the remote control. Don't press two or more buttons at the same time, unless you are

specifically instructed to do so in this owner's guide.

Don't allow the remote control to get wet or become heated.

Avoid dropping the remote control on a hard surface.

tab in

When cleaning the remote control, don't use any harsh chemicals. Use only a soft, slightly moistened cloth.

Don't mix new batteries with old ones.

Don't heat, take apart, or throw batteries into afire.

Use alkaline batteries.

Using the remote control with yourTV

You can use your remote to control the TV, CABLE/DBS,VCR,

DVD or AUDIO. The remote has been preset to operate the TV and other Mitsubishi products. It can be set to control other audio/video equipment.

To operate the TV, the select switch at the top of the remote should be set toTV.

C_LE/DB$ VGR DVD

ooo 0

O O 0 O O 0

Remote Control of Other Audio and Video Products

Programming the Remote to Control OtherAudio andVideo Products:

Move the slide switch at the top of the remote to select the

audio or video product you want to control.

Press and hold the POWER button, so that it stays down when

you enter the code.

Enter the code for the equipment from the appropriate list, exactly as stated. If there is more than one code number, start with the first number. After setting the code, release the

POWER button.

Point the remote at the equipment and press the POWER button. If it is on and turns off or is off and turns on, the

remote will control the equipment. If not, try the next number.

Cable Box codes:

Cable box brand codeto enter: If your

General Instruments/ 111,119, 120, 121,122, cable box Jerrold 123, 124, 125, 126, 127 code is not Oak 102, 137, 139 listed here,

Pioneer 101, 116 page 63 Scientific Atlanta 111,112,113 for a

Zenith 100, 117 complete

To reset to default code, enter 000 listing,

Satellite Receiver codes:

Satellite brand

Dishnetwork Hughes-DSS

RCA-DSS

Sony-DSS 177 Toshiba-DSS 170

Panasonic-DSS 174 Pdmestar 178

To reset to default

codetoenter:

175 " 173

176

code, enter 000

please see

If your

satellite code is not

listed here

)lease see

page 63

for a complete

listing,

VCR codes:

VCR brand codeto enter:

Mitsubishi 001,002 VCR Hitachi 020, 043, 065 code is not JVC 030, 054,059 listed here,

Philips/Magnavox 043,044, 051 please see Panasonic 041,042, 043 page 64

RCA 020, 053, 065 for a Sony 048,049, 050 complete

Toshiba 021,066 listing.

TO reset to default code, enter 000

If your

CABLE/DeS DVD

VCR

Tv.ll Aoo,o

I M PO RTA NT

If you cannot turn the cable box ON by pressing POWER, try pressing the

CHANNEL or the number buttons.

CABLE/DBS OVD

CABLE/DeS

When set to TV, the PLAY, STOP, REW/

REV and the FF/FWD keys will operate

theVCR after theVCR codes have been chosen.

VCR

I M PO RTA NT

Remote Control of Other Audio and Video Prod- uct, continued

DVD Player codes:

DVD/LDP brand

Mitsubishi (DVD) Mitsubishi (LDP)

Panasonic Pioneer DVD (LDP)

Sony Toshiba

To reset to default code, enter 000

codeto enter:

003 016, 017

250 252 (016,017)

254 253

AV Receiver codes:

Audio brand

Mitsubishi AV receiver Mitsubishi CD player

Kenwood Onkyo

Pioneer Sony

Yamaha

To reset to default code, enter 000

code_ en_r:

010,011,012 013,014,015

200,208 209,214

205,207 222

201,202

If your DVD code is not

listed here, please see page 63

for a complete listing.

If your

Audio code is not listed here, please see page 63

for a complete listing.

CABLE/DaS

CABLE/DBS DVD

IMPORTANT

If the slide switch is set toTV when you enter an AV receiver code,VOLUME and

MUTE will be controlled by theAV receiver.

VCR

Additional slide switch feature:-for multiple AJV component systems

Your Mitsubishi remote control was designed for flexibility in both large and smallA/V systems.

For example, you can use the slide switch in the following way:

If you have twoVCR's, but no DVD player, move the slide switch to the DVD position and enter

the secondVCR code. Then when the slide switch is moved to DVD you can control the second VCR.

The following chart shows which device can be entered for each position. Only one device is allowed for each slide switch position.

TV position:

• TV

• any A/V receiver

Cable/DBS position:

• cable box

• satellite receiver

(volume, mute only)

VCR position: Audio position:

• any VCR • anyAV receiver

• Mitsubishi DVD • Mitsubishi CD player player • cable box

/ Some manufacturers may change their products, or they may

I[ IM PORTANT

J use more than one remote control system. If this isthe case,

your remote_maY -not be able to operate yourVCR, Cable Box,

.................................

DVD position:

• any DVD

• any VCR

• cable box

Remote Control Functions

Select switch

Selects which AN wilt be controlled by the

remote

Power

power on and off for theTV

or otherAN products

Numbers

To individually select

channels or enter

information into TV

SQV (SuperQuickView TM)

Scan through a memorized list of favorite channels

INPUT

Selectsthe signal you will watch (Ant A; Ant B;Input I, 2 or 3; DVD)

CHANNEL

View channelsin increasingor decreasingnumerical order

QV (QuickView)

-- Switchesto last channelviewed

SLEEP

Sets theTV to turn off within 2 hours

VIDEO

Individually adjuststheVideo settings

AUDIO

Adualtyadjusts

the Audio settings

VOLUME

Increasesordecreasessound

MUTE

rurnsonoroffthesound

Remote Control Functions, continued

ENTER

Use after selecting a channel number or

menu item

LIGHT For VS-50705,VS-55705,VS-60705

and VS-70705, press to light up the remote control

CANCEL

Clear SQV and some menu entries

PIP or PIP/POP

Useto display,move, resize or changea PIP

channel.ForVS-50705,

VS-55705,VS-60705and VS-70705 useto display,

resize or changea POP

channel

ooo 0

OOO OOO

GO0 _

ADJUST

Selects menu items. Moves the PIP

on-screen location

GUIDEFor VS-S0705,VS-SS705, VS-60705 andVS-70705.

satellite systems program guides

Displays on-screen menu choices

HOME

Exit on-screen menusand return to TV viewing

INFO

Displays an on-screen summary of currentTV settings

REC

Manually record

programs on your VCP_,_

REW/REV

Rewind and reverse search for

theVCR. Skip reverse for CD.

Reverse scan for DVD

PLAY PlaysaVCR,

OOOo

000 000 000 _

JJJ

STOP

Tostop aVCR, DVD or

PAUSE

_Temporarity stops a

VCR, DVD or CD or freezes the PIP/POP

FF/FWD

ast forward or forward search

for aVCR. Skip forward for a CD. Fast play for a DVD

Your television has Mitsubishi's exclusive _l_on screen operating system, which provides on- screen information for menu choices and changes.

A highlighted icon isshown when there isanother men u level for your

choices. Pressingthe ENTER button will displaythe men uoptions.

Make choicesor changestoamen u itemwhen you seea button.

The ViewPoint system includes the following special features:

The selected icon or button is highlighted with a yellow outline and the text color will be yellow.

On-screen instructions provide complete menu choice information.

Some on-screenmenu optionsmust be setbeforeotheroptionsare

available. For example,"Set theTimer" will only be possible if "ClockTime" and "Set Day" have been set.

0 0 @

O0 O0

O0 _

Making Selections:

IST• or • to select the menu item you want to change ADJUST _' to move to the selection field ADJUST • or • to change the settings

UST • to move back to the menu item

• • _ ENTER E_:_to select an option, or start an automatic function

•CANCELC_:_ Lto clear a setting, or stop anautomatic function

To exit the on-screen menus:

MENU Press the MENU key to move back one menu screen at a time

until you exit all the menus to return to television viewing

Press HOME to exit all menus with one keystroke and return to

television viewing

+ 49 hidden pages