Mitsubishi TFW9105SKTKW User Manual

AUTO-SCANNING WITH DIGITAL CONTROL
COLOR DISPLAY MONITOR

For future reference, record the serial
number of your display monitor in the
space below:
SERIAL No.
The serial number is located on the
rear cover of the monitor.

MITSUBISHI

USER'S GUIDE

MODEL

TFW9105SKTKW

Trademark

IBM, PC, PS/2, PS/V, Personal System/2 are registered trademarks of International Business
Machines Corp.
Apple Macintosh is a registered trademark of Apple Computer, Inc.
Quadra is a trademark of Apple Computer, Inc.

© 1996 MITSUBISHI ELECTRIC CORPORATION

CAUTION

The power cord provided with this monitor is designed for safety
and must be used with a properly grounded outlet to avoid possible
electrical shock.

Do not remove the monitor cabinet as this can expose you to very
high voltages and other hazards.

ANMERKUNG:

Dieser Monitor erfüllt die Anforderungen der deutschen Ergonomie-Norm ZH1/
618/10.80 bei Verwendung der beiden folgenden Timing:

Auflösung Videoeingang fH(kHz) fv(Hz) Interlace/Non-Interlace
1600x1200 Analog RGB, 0.7Vs-s 89.1 72.0 Non-Interlaced

Aus ergonomischen Gründen wird empfohlen, die Grundfarbe Blau nicht auf
dunklerem Untergrund zu verwenden (schlechte Erkennbarkeit, Augenbelastung
bei zu geringem Zeichenkontrast).

Bei hellem Hintergrund empfehlen wir aus ergonomischen Gründen nur
Vertikalfrequenzen größer oder gleich 70Hz zu verwenden.

Zur Trennung vom Netz ist der Netzstecker aus der Steckdose zu ziehen,
welche sich in der Nähe des Gerätes befinden muß und leicht zugänglich sein
soll.

Das Gerät stellt sich automatisch auf die zutreffende Nennspannung ein.

注意
 この装置は、情報処理装置等電波障害自主規制協議会（VCCI）の基準に基づく
第一種情報技術装置です。この装置を家庭環境で使用すると電波妨害を引き起こす
ことがあります。この場合には使用者が適切な対策を講ずるよう要求されることが
あります。

高調波ガイドライン適合

品

2

RADIO INTERFERENCE REGULATIONS STATEMENT FOR U.S.A.

This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installa­tion. This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interfer­ence will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

THIS PRODUCT HAS BEEN TESTED AND FOUND TO COMPLY
WITH THE LIMITS WITH SIGNAL CABLE SC-B102. USE IT TO
REDUCE THE POSSIBILITY OF CAUSING INTERFERENCE TO
RADIO, TELEVISION, AND OTHER ELECTRIC DEVICES.

NO USER SERVICEABLE PARTS INSIDE. DO NOT ATTEMPT TO
MODIFY THIS EQUIPMENT. IF MODIFIED, YOUR AUTHORITY TO
OPERATE THIS EQUIPMENT MIGHT BE VOIDED BY FCC.

WARNING!

This product is not designed for use in life support devices and Mitsubishi Electric
corporation makes no representations to the contrary. Life support devices are
those devices which are used to measure, diagnose, or evaluate the tissue, sys­tems or functions of the human body; or other devices employed to support or
sustain life or good health.

MANUFACTURER DECLARATION FOR CE-MARKING:

We, Mitsubishi Electric Corp., declare under our sole responsibillity, that this
product is in conformity with the following standards:

EN60950
EN55022 Class B
EN50082-1
EN61000-3-2

following the provisions of:

73/23/EEC Low Voltage Directive
89/336/EEC EMC Directive

As an ENERGY STAR Partner, Mitsubishi Electric Corporation has determined that
this product meets the ENERGY STAR guidelines for energy efficiency.

3

Congratulations! You have just purchased a TCO'95 approved and labelled product! Your
choice has provided you with a product developed for professional use. Your purchase
has also contributed to reducing the burden on the environment and to the further
development of environmentally-adapted electronic products.

Why do we have environmentally-labelled computers?

In many countries, environmental labelling has become an established method for
encouraging the adaptation of goods and services to the environment. The main problem
as far as computers and other electronic equipment are concerned is that environmentally
harmful substances are used both in the products and during their manufacture. Since it
has not been possible so far for the majority of electronic equipment to be recycled in a
satisfactory way, most of these potentially damaging substances sooner or later enter
Nature.

There are also other characteristics of a computer, such as energy consumption levels,
that are important from both the working and natural environment viewpoints. Since all
types of conventional electricity generation have a negative effect on the environment
(acidic and climate-influencing emissions, radioactive waste, etc.), it is vital to conserve
energy. Electronic equipment in offices consumes an enormous amount of energy, since it
is often routinely left running continuously.

What does labelling involve?

This product meets the requirements for the TCO'95 scheme, which provides for
international environmental labelling of personal computers. The labelling scheme was
developed as a joint effort by the TCO (The Swedish Confederation of Professional
Employees), Naturskyddsforeningen (The Swedish Society for Nature Conservation) and
NUTEK (The National Board for Industrial and Technical Development in Sweden).

The requirements cover a wide range of issues: environment, ergonomics, usability,
emission of electrical and magnetic fields, energy consumption and electrical and fire safety.

The environmental demands concern among other things restrictions on the presence
and use of heavy metals, brominated and chlorinated flame retardants, CFCs (freons),
and chlorinated solvents. The product must be prepared for recycling and the manufacturer
is obliged to have an environmental plan, which must be adhered to in each country where
the company implements its operational policy.

The energy requirements include a demand that the computer and/or display after a certain
period of inactivity shall reduce its power consumption to a lower level, in one or more
stages. The length of time to reactivate the computer shall be reasonable for the user.

Labelled products must meet strict environmental demands, for example in respect of the
reduction of electric and magnetic fields, along with physical and visual ergonomics and
good usability.

4

In and after the middle of this page, you will find a brief summary of the environmental
requirements met by this product. The complete environmental criteria document may be
ordered from:
TCO Development Unit
S-114 94 Stockholm
Sweden
Fax: [phone]
E-mail (Internet): [e-mail]
Current information regarding TCO'95 approved and labelled products may also be
obtained via the Internet, using the address:
http//www.tco-info.com/
TCO'95 is a co-operative project between

Environmental Requirements

Brominated flame retardants are present in printed circuit boards, cabling, casings and
housings, and are added to delay the spread of fire. Up to 30 % of the plastic in a computer
casing can consist of flame-retardant substances. These are related to another group of
environmental toxins, PCB, and are suspected of giving rise to similar harm, including repro­ductive damage in fish-eating birds and mammals. Flame retardants have been found in
human blood and researchers fear that they can disturb foetus development.
Bio-accumulative* TCO'95 demands require that plastic components weighing more than 25
grammes must not contain frame retardants with organically bound chlorine or bromine.

Lead

can be found in picture tubes, display screens, solder and capacitors. Lead damages the
nervous system and in higher doses, causes lead poisoning.
The relevant bio-accumulative* TCO'95 requirement permits the inclusion of lead, as no
replacement has yet been developed.

Cadmium

is present in rechargeable batteries and in the colour-generating layers of certain computer
displays. Cadmium damages the nervous system and is toxic in high doses.
The relevant bio-accumulative* TCO'95 requirement states that batteries may not contain
more than 25 ppm (parts per million) of cadmium. The colour-generating layers of display
screens must not contain any cadmium.

Mercury

is sometimes found in batteries, relays and switches. Mercury damages the nervous system
and is toxic in high doses. The relevant bio-accumulative* TCO'95 requirement states that
batteries may no contain more than 25 ppm (part per million) of mercury.

demands require that no mercury is present in any of the electrical or electronic components
concerned with the display unit.

CFCs (freons) are sometimes used for washing printed circuit boards and in the

manufacture of expanded foam for packaging. CFCs break down ozone and thereby
damage the ozone layer in the stratosphere, causing increased reception on Earth of
ultra-violet light with consequent increased risks of skin cancer (malignant melanoma).
The relevant TCO'95 requirement: Neither CFCs nor HCFCs may be used during
manufacture of the product or its packaging.

* Bio-accumulative is defined as substances which accumulate within living organisms.

5

Diamond Pro 91TXM
User’s Guide

CONTENTS

1. INTRODUCTION .................................................................................................. 6

1.1 Features ..................................................................................................... 6

1.2 Internal Preset Memory Capability ............................................................. 7

1.3 Power Management Function .................................................................... 7

1.4 DDC ........................................................................................................... 8

1.5 Location Considerations ............................................................................ 8

1.6 Cleaning Your Monitor ............................................................................... 8

1.7 Unpacking .................................................................................................. 9

1.8 Tilt/Swivel Base ......................................................................................... 9

Screen Position Adjustment ....................................................................... 9

1.9 Quick Operation Chart ............................................................................... 10

2. CONNECTING THE MONITOR ........................................................................... 11

2.1 AC Power Connection ............................................................................... 11

2.2 Signal Cable Connection ........................................................................... 11

2.2.1 Connecting to Any IBM VGA Compatible System .............................. 11

2.2.2 Connecting to An Apple Macintosh Centris, Quadra, and

Apple Macintosh II Family .................................................................. 12

2.2.3 Connecting to a Unix Work Station & Third Party Graphics Card ...... 13

3. USER CONTROLS ............................................................................................. 15

4. OSD(On Screen Display) FUNCTIONS ............................................................... 17

4.1 Normal Mode Operation ............................................................................ 18

4.2 Enhanced Mode Operation ........................................................................ 22

5. TROUBLESHOOTING ......................................................................................... 25

6. SPECIFICATIONS ............................................................................................... 26

7. APPENDIX ........................................................................................................... 27

7.1 Monitor Signal Input Connector (DB9-15P) ............................................... 27

7.2 Serial Interface Input Connector (DIN-8P) For Serial Interface Function .. 27

7.3 SC-B102 Signal Cable ............................................................................... 28

7.4 Macintosh Adapter AD-A205 settings ........................................................ 29

Note : This manual is designed for use with Diamond Pro 91TXM color display monitor.

6

1

1

INTRODUCTION

Congratulations on your purchase of the Diamond Pro 91TXM high resolution color monitor.
Mitsubishi designed this monitor to provide you with years of reliable trouble-free operation. Once
again, thank you for selecting our product and welcome to Mitsubishi!
This guide tells you how to connect, adjust and care for your Diamond Pro 91TX M monitor. This guide
also provides technical specifications and instructions for troubleshooting any basic problems you
may experience with your monitor.

1.1 Features

The Diamond Pro 91TXM is a 55cm/21"(50cm/19.7" Diagonal Viewable Image) intelligent, micropro­cessor-based monitor compatible with most analog RGB (Red, Green, Blue) display standards,
including PS/V

®

, PS/2®, Apple® Macintosh® Centris, Quadra, and Macintosh II family signals. It
provides crisp text and vivid color graphics with VGA, SVGA, XGA (non-interlaced), and most
Macintosh compatible color video cards.

• The monitor’s wide auto-scanning compatibility range makes it possible to upgrade video cards or

software without purchasing a new monitor.

• Digitally controlled auto-scanning is done using an internal microprocessor, for horizontal scan

frequencies between 30kHz and 95kHz, and vertical scan frequencies between 50Hz and 152Hz.
The microprocessor-based intelligence allows the monitor to operate in each frequency mode with
the precision of a fixed frequency monitor.

• The monitor contains resident memory for pre-programmed screen display standards and is also

capable of storing additional user adjustment parameters.

• The monitor is capable of producing a maximum addressable resolution format of 1600 x 1200 lines

typically. This display is well suited for windowing environments.

• Because of the analog signal inputs, the monitor can display an unlimited palette of colors that can

be manually adjusted to suit your specific needs.

• The monitor has a power management function accorded to VESA-DPMS-standard. To save

energy, the monitor must be connected to a system compliant with the VESA DPMS-standard.
(Refer to your computer and/or video card instructions for proper operation.)

• The monitor has a serial interface which permits software control of the monitor’s functions when

using the optional serial interface kit.

• To ensure ease of installation and ongoing use, the monitor features Moire Clear Function and On-

Screen Display (OSD) of all monitor set-up and adjustment functions.

• For use in a variety of applications, the monitor complies with UL 1950, CSA C22.2 No.950 and

EN60950 for safety, FCC Class-B, VCCI Class I and EN55022 Class-B for EMI, MPR-II and ISO
9241-3 for ergonomics. The monitor also complies with TCO'95 guideline for environmentally safe
use.

• Digital Chassis design for lighter, more compact enclosure and increased screen performance.

• DIAMONDTRON CRT with 0.28mm pitch aperture-grille mask, advanced-focus P-NX DBF

(Dynamic Beam Forming) electron gun and high contrast optical-quality coating.

• The monitor complies with Video Electronics Standards Association (VESA

TM

) DDC1/2B(EDID)

specification. If your computer provides DDC1/2B(EDID) function, setup will be done automatically.

7

MEMORY PRESET Polarity
BUFFER TIMING Fh (KHz) Fv (Hz) H V

1 1600 x 1200 N.I. 93.7 75 + +
2 1280 x 1024 N.I. 79.9 75 + +
3 1152 x 870 N.I. 68.7 75 - ­4 1024 x 768 N.I. 60.0 75 + +
5 800 x 600 N.I. 46.8 75 + +
6 640 x 480 N.I. 37.5 75 - -

Table 1. Memory Buffer Factory Presets

1.2 Internal Preset Memory Capability

To minimize adjustment needs, the factory has preset popular display standards into the monitor,
as shown in Table 1. If any of these display standards are detected, the picture size and center­ing are automatically adjusted. All of the factory presets may be overwritten by adjusting the user
controls. The monitor is capable of automatically storing up to twelve additional display stan­dards. The new display information must differ from any of the existing display standards by at
least 1kHz for the horizontal scan frequency or 5Hz for the vertical scan frequency or the sync
signal polarities must be different.

1.3 Power Management Function

The monitor has the power management function which reduces the power consumption of the
monitor when not in use. There are two reduced power level modes.

Stand-by mode

When the horizontal sync signal is off, the monitor is switched to a stand-by mode. When the
monitor is in stand-by mode, the screen is off and the power indicator will blink for 0.5 second
intervals.
After the horizontal sync signal is restored, picture will be displayed immediately.

Suspend mode

When the vertical sync signal is off, after about 10 seconds the monitor is switched to a
suspend mode which reduces the monitor power consumption to less than 15W.
When the monitor is in suspend mode, the screen is off and the power indicator will blink for
two second intervals. After the vertical sync signal is restored, picture will be displayed within
a few seconds.

Power-off mode

When the horizontal sync signal and vertical sync signal are off, after about 10 seconds the
monitor is switched to a power-off mode, which reduces the monitor power consumption to
less than the power consumed at suspend mode above.
When the monitor is in power-off mode, the screen is off, and the power indicator will blink for
3 seconds of On-time and 1 second Off-time.
After both the sync signals are restored, picture will be displayed within several seconds.

8

1.5 Location Considerations

When setting up and using the monitor, keep the following in mind:

* For optimum viewing, avoid placing the monitor against a bright background or where sunlight

or other light sources may reflect on the display area of the monitor; place the monitor just
below eye level.

* Place the monitor away from strong magnetic or electromagnetic fields, such as

high capacity transformers, electric motors, large current power lines, steel pillars,

etc.... Magnetism can cause distortion in the picture and/or color purity.

* Avoid covering the slots or openings of the monitor. Allow adequate ventilation

around the monitor so the heat from the monitor can properly dissipate. Avoid putting the
monitor into any enclosure that does not have adequate ventilation.

* Avoid exposing the monitor to rain, excessive moisture, or dust, as this can

cause a fire or shock hazard.

* Avoid placing the monitor, or any other heavy object, on the power cord.

Damage to the power cord can cause a fire or electrical shock.

* When transporting the monitor, handle it with care.

CAUTION

Keep your fingers away from the pivot area of the tilt/swivel base.

1.6 Cleaning Your Monitor

When cleaning the monitor, please follow these guidelines:

* Always unplug the monitor before cleaning.
* Wipe the screen and cabinet front and sides with a soft cloth.
* If the screen requires more than dusting, apply a household window cleaner to a soft cloth to

clean the monitor screen.

CAUTION

Do not use benzene, thinner or any volatile substances to clean the unit as the finish may be
permanently marked. Never leave the monitor in contact with rubber or vinyl for an extended time
period.

1.4 DDC

The monitor includes the DDC1 and DDC2B feature. DDC (Display Data Channel) is a communi­cation channel over which the monitor automatically informs the host system about its capabilities
(e.g. each supported resolution with its corresponding timing).
DDC is routed through previously unused pins of the 15-pin VGA connector.
The system will perform "Plug and Play" feature if both, monitor and host, implement the DDC
protocol.

9

1. Diamond Pro 91TXM Color Monitor

2. AC Power Cord

3. Signal Cable SC-B102

4. Macintosh Adapter AD-A205

5. User’s Guide

6. Warranty-Card

7. Questionnaire-Card

1

4

3

2

Figure 1.

5°

1010°

4545°

4545°

1.8 Tilt/Swivel Base

The monitor comes with a tilt/swivel base. This enables you to position the monitor to the best
angle and tilt for maximum viewing comfort.

Screen Position Adjustment

Adjust the tilt and rotation of the monitor by placing your hands at opposite sides of the case, as
shown in Figure 2. You can adjust the monitor 45 degrees right or left, 10 degrees up or 5
degrees down, as shown below.

Figure 2.

ON

1 2 3

4

5 6

AD-A205

M

I

T

S

U

B

I

S

H

I

1.7 Unpacking

After you unpack the box you should have all of the items indicated in Figure 1. Save the box
and packing materials in case you ship or transport the monitor. Complete and mail in warranty
cards.

5

6

7

10

1.9 Quick Operation Chart

To summarize the steps in connecting your computer and adapter with Diamond Pro
91TXM color monitor and setting the necessary controls and switches, refer to the chart
below.

Turn on the computer.

Set the controls and switches.

See 5. TROUBLESHOOTING

If the problem persists.

Turn on the Diamond Pro 91TXM color monitor.

Connect the power cord to the Diamond Pro 91TXM
color monitor and the signal cable between the Diamond
Pro 91TXM and the graphics adapter.

OK

OK

If a problem appears.

See 2.1 AC Power Connection

2.2 Signal Cable Connection

See 3. USER CONTROLS

4. FUNCTION CONTROLS

Call for your authorized MITSUBISHI
Product Support at 1-800-344-6352.

11

2

2 CONNECTING THE MONITOR

On the back of the monitor are four plug-in connections: one for the AC power cord, DB9-15P
connector, BNC connector for video and a DIN-8P connector for the optional serial interface kit.

2.1 AC Power Connection

One end of the AC power cord is connected into the AC power connector on the back of the
monitor. The other end is plugged into a properly grounded three-prong AC outlet. The
monitor’s auto-sensing power supply can automatically detect 100-120V AC or 200-240V AC and
50 or 60Hz.

2.2 Signal Cable Connection

The attached video signal cable provides a DB9-15P connector for the VGA compatible analog
RGB outputs on your computer. The RGB signal may be derived from an IBM® PS/2, or compat­ible Apple Macintosh built-in video. Most third party color cards can also be interfaced using the
free Mitsubishi Apple adaptor available from your dealer.

2.2.1 Connecting to Any IBM VGA Compatible System

Figure 3 shows the SC-B102 cable connection to the Video Graphics Array (VGA) port in an IBM
Personal System/2

®

Model 50, 60, 70 and 80, or any VGA compatible system.

1. Power off, the monitor and the computer.

2. Connect the one end of the SC-B102 cable to the 15-pin connector on the VGA controller
card.

3. Connect the other end of the SC-B102 cable to the DB9-15P receptacle on the back of
the monitor.

4. Power on the computer, then the monitor.

5. After using the system, power off the monitor, then the computer.

CAUTION

The socket-outlet shall be installed near the equipment and shall be easily accessible.
During servicing, disconnect the plug from the socket-outlet.

Méme si le moniteur est mis hors tension il reste toujours alimenté. La prise secteur
devrait ainsi ètre facilement accssible en cas d'urgence.

Figure 3.

Power Cord

Computer

VGA

Compatible

System

CABLE SC-B102

DB9-15P

DB9-15P

RGB VD

COMP.
HD

75

Sync

1k

D-SUB

BNC

Serial

12

2.2.2 Connecting to An Apple Macintosh Centris, Quadra, and Apple Macintosh II
Family

Figure 4 shows the SC-B102 cable and AD-A205 Adapter to the video port in an Apple
Macintosh.

1. Power off, both the monitor and the computer.

2. Set the DIP switches of Macintosh Adapter according to the setting chart.
(See 7.4 Macintosh Adapter AD-A205 settings)

3. Connect the 15-pin (DB-15P) end of the AD-A205 Adapter to the straight 15-pin
connector on the Macintosh video port on the CPU or on the video board.

4. Connect the sub-miniature 15-pin (DB9-15P) end of AD-A205 Adapter to the
SC-B102 cable.

5. Connect the other end of the SC-B102 cable to the DB9-15P receptacle on the
back of the monitor.

6. Power on the Macintosh, then the monitor.

7. After using the system, power off the monitor, then the Macintosh.

Power Cord CABLE SC-B102

Please see APPENDIX (7.4 Macintosh Adapter AD-205 settings).

Figure 4.

DB-15P
DB9-15P

Apple

Macintosh

Computer

Macintosh

Adapter

AD-A205

DB9-15P

RGB VD

COMP.
HD

75

Sync

1k

D-SUB

BNC

Serial

13

2.2.3 Connecting to a Unix Workstation & Third Party Graphics Card

Figure 5 shows the SC-B102 or “75 ” coaxial cable (not supplied) connection to the
graphics video card (PC-CAD and workstation).

1. Power off, both the monitor and the computer.

2. Connect one end of the SC-B102 cable or the “75

” coaxial cable to the output

connector on the CPU, or on the video board.

3. Connect the other end of the SC-B102 cable or the “75

” coaxial cable to the

DB9-15P receptacle or the BNC receptacles on the back of the monitor.

4. Power on the computer, then the monitor.

5. After using the system, power off the monitor, then the computer.

High Resolution

Graphic Video Card

“75 ” coaxial cable

Cable SC-B102

Power Cord

DB9-15P

Please see next page about BNC connection.

High Resolution

Graphic Video Card

Figure 5.

RGB VD

COMP.
HD

75

Sync

1k

D-SUB

BNC

Serial

14

(1) IN CASE OF A COMPOSITE SYNC ON GREEN VIDEO SIGNAL (SYNC ON GREEN):

Connect the R, G and B video signals to the BNC receptacles on the back of the monitor.

(2) IN CASE OF EXTERNAL COMPOSITE SYNC SIGNAL:

Connect the R, G and B video signals and the Composite sync signal to BNC receptacles on
rear panel, respectively.

(3) IN CASE OF SEPARATE HORIZONTAL AND VERTICAL SYNC SIGNALS:

Connect the R, G and B video signals and the horizontal and vertical sync signals to the BNC
receptacles on the rear panel.

NOTE: Set the"75

"/"1k " TERMINATION SWITCH to the "1k " position when using a TTL

sync signal, otherwise set to the "75 " position.

BNC CONNECTION

RG B VD

Serial

COMP.

HD.

75

Sync

1k

D-SUB

BNC

〜

RG B VD

Serial

COMP.

HD.

75

Sync

1k

D-SUB

BNC

〜

RG B VD

Serial

COMP.

HD.

75

Sync

1k

D-SUB

BNC

〜

15

3

3 USER CONTROLS

See Figure 6 and 7 for the location of the following user controls and indicators.
Each control is identified by number and is described individually on each page.

8. CONTRAST CONTROL
KNOB

1. POWER SWITCH

2. POWER-ON INDICATOR

[How to use the front control panel]
Press the button marked “

” on
the control panel to open.To close,
press it again.

5. FUNCTION SELECT BUTTONS

Figure 6

1. POWER SWITCH: A push-on push-off switch for AC power.

2. POWER-ON INDICATOR: This indicator illuminates when AC power is on.

3. RESET BUTTON: Push the RESET button to restore a factory preset that has been modified
by the user. This button performs two functions under different conditions.

1. When adjusting H-SIZE, H-PHASE, V-SIZE, V-PHASE, PCC-AMP or PCC-PHASE

controls, pressing the RESET button will restore the factory adjusted screen geometry and
size settings, if the current video signal timing corresponds to a factory preset timing.

2. When adjusting color gains, pressing the RESET button will restore the factory adjusted

color gain for the currently selected color memory number.

4. INPUT CONNECTOR SELECT BUTTON: Push the BNC/D-SUB button to select the input
signal BNC or D-SUB. By the OSD function, input signal could select, either. (See 4.1 (3)
Connector select)

5. FUNCTION SELECT BUTTONS: Push the adjust buttons to choose one of the functions that
is superimposed on the display screen.

6. FUNCTION ADJUST BUTTONS: Push the adjust buttons to adjust the image on the screen
that is selected via the function select buttons.

7. DEGAUSS BUTTON: A push type button that is used to eliminate possible color shading or
impurity.

7. DEGAUSS BUTTON

3. RESET BUTTON

FRONT

RESET BNC/D-SUB

RESET BNC/D-SUB

ADJUST DEGAUSS

ADJUST DEGAUSS

SELECT

SELECT

6. FUNCTION ADJUST BUTTONS

4. INPUT CONNECTOR SELECT BUTTON

16

RG B VD

Serial

COMP.

HD.

75

Sync

1k

D-SUB

BNC

〜

REAR

AC POWER CONNECTION

8. CONTRAST CONTROL KNOB: Turn the control clockwise to increase contrast. Contrast
may also be adjusted from the OSD menu using plus and minus bottons.

9. SERIAL INTERFACE CONNECTOR: The monitor has a DIN-8P connector for connect-
ing to the computer when using the optional serial interface kit. For information about
connecting the serial interface, please refer to the instructions included with the serial
interface kit.

For further information about the optional serial interface kit, please contact your autho­rized MITSUBISHI dealer.

10. SYNC TERMINATION SWITCH: Set the 75

/1k sync termination switch to the 1k
position when using a TTL sync signal, otherwise set to 75 position.
(This switch is effective for BNC INPUT. For the DB9-15P input, Synctermination is 1k

fix.)

SIGNAL INPUT CONNECTOR (BNC)

SIGNAL INPUT CONNECTOR

(DB9-15P)

Figure 7

9. SERIAL INTERFACE CONNECTOR
(DIN-8P)

10. SYNC TERMINATION SWITCH

17

4

4

OSD(On Screen Display) FUNCTIONS

(1) CONTRAST: Adjusts to the desired contrast level.
(2) BRIGHTNESS: Adjusts to the black level of the screen.
(3) CONNECTOR-SELECT: Selects the video input connection to be used.
(4) H-SIZE (Horizontal Size): Controls the horizontal size of the image on the screen.
(5) H-PHASE (Horizontal Position):

Controls the horizontal position of the image on the screen.
(6) V-SIZE (Vertical Size): Controls the vertical size of the image on the screen.
(7) V-POSITION (Vertical Position): Controls the vertical position of the image on the screen.
(8) PCC-AMP (Pincushion or Bow Amplitude):

Straightens the left and right sides of the screen image.
(9) PCC-PHASE: Adjusts the parallelism of the left and right sides of the screen image.
(10)PIN-BALANCE: Adjusts the curvature of the left and right sides of the screen image.
(11)KEY-BALANCE: Adjusts the vertical slant or tilt of the screen image.
(12)ROTATION: Adjusts the rotation or twist of the picture.
(13)H-STATIC: Adjusts the horizontal alignment of the red, green and blue beams.
(14)COLOR 1-RED, COLOR 2-RED, COLOR 3-RED:

Provides the red-color balances for the display.
(15)COLOR 1-GREEN, COLOR 2-GREEN, COLOR 3-GREEN:

Providesthegreen-colorbalancesforthedisplay.
(16)COLOR 1-BLUE, COLOR 2-BLUE, COLOR 3-BLUE:

Providestheblue-colorbalancesforthedisplay.
(17)POWER-SAVE (ON/OFF):

WhenadjustingON,reducesthepowerconsumptionofthemonitorwhen

notinuse.
(18)MOIRE-CLEAR (ON/OFF):

WhenadjustingON,themoirelevelonthescreencandecreasedbythe

MOIRE-CLEARLEVEL.
(19)MOIRE-CLEAR LEVEL:

WhenMOIRE-CLEARison,decreasesthemoirelevelonthescreen.

NORMAL-MODE

(20)H-POSI (Horizontal Position): Adjusts the horizontal position of the screen.
(21)CENTER-PCC (Center Pincushion or Bow Amplitude):

Adjusts the pincushioning near the vertical center of the screen.

(22)CORNER-PCC (Top of Pincushion or Bow Amplitude):

Adjusts the pincushioning at the top corners of the screen.

(23)BOTTOM-PCC (Bottom of Pincushion or Bow Amplitude):

Adjusts the pincushioning at the bottom corners of the screen.
(24)TOP-BALANCE: Move the top of the screen image to the right and left.
(25)PCC-SINE: Move the expanded part from top to bottom and bottom to top.
(26)CLAMP PULSE POSITION:

Use this function to eliminate excessive green or white background that

may occur when both Sync-On-Green and external sync signals are

applied to the monitor.
(27)PURITY: Adjusts the purity of the screen.
(28)VIDEO LEVEL: Selects video levels 1.0V or 0.7V.

ENHANCED-MODE

18

4.1 Normal Mode Operation

Press any select button and control indicators will be superimposed on the display screen.
Refer to Figure 6 for the location of the monitor function ( ) controls. Press
the select buttons to choose one of the following controls.
When the indicator of a function symbol comes on the screen and changes to blue, that control is
active and can be adjusted by the adjust buttons. The monitor automatically memorizes all
adjustments.
If you don't touch the control switches for ten seconds, the OSD screen will disappear.
For faster OSD blanking, push buttons simultaneously.

Press the Plus Adjust Button:

Press the Minus Adjust Button:

FUNCTION AND OSD

(3) CONNECTOR-SELECT

Press the minus adjust
button to select the D­SUB input connector.

Press the plus adjust
button to select the BNC
input connector.

If the selected connector has no signal, the monitor
will select another one automatically.

Press plus and minus buttons together, to restore to
factory preset level.

To increase the brightness.

To decrease the brightness.

To increase the contrast.

To decrease the contrast.

Press plus and minus buttons together, to restore to
factory preset level.

(2) BRIGHTNESS

NORMAL

NORMAL

CONTRAST

CONTRAST

BRIGHT

BRIGHT

CONNECTOR

CONNECTOR

50%

(1) CONTRAST

NORMAL

NORMAL

CONTRAST

CONTRAST

BRIGHT

BRIGHT

CONNECTOR

CONNECTOR

50%

Button: select up
Button: select down
Button: select right
Button: select left

Front Control Panel

RESET BNC/D-SUB

RESET BNC/D-SUB

ADJUST DEGAUSS

ADJUST DEGAUSS

SELECT

SELECT

D-SUB

D-SUB

NORMAL

NORMAL

CONTRAST

CONTRAST

BRIGHT

BRIGHT

CONNECTOR

CONNECTOR

BNC

BNC

19

Press the Plus Adjust Button:

Press the Minus Adjust Button:

FUNCTION AND OSD

To expand the center of
the image.

To collapse the center of
the image.

(8) PCC-AMP (Pincushion or Bow Amplitude)

(7) V-POSITION (Vertical Position)

To move the image up.

To move the image down.

(6) V-SIZE(Vertical Size)

To narrow the height of
the image on the screen.

To expand the height of
the image on the screen.

To move the image to the
right.



H-SIZE

50%

(4) H-SIZE (Horizontal Size)

To expand the width of
the image on the screen.

To narrow the width of the
image on the screen.

To move the image to the
left.

H-PHASE

50%

(5) H-PHASE(Horizontal Position)



50%

V-SIZE



PCC-AMP

50%



V-POSI

50%

50%

20

Press the Plus Adjust Button:

Press the Minus Adjust Button:

50%

RB

RB

RB

RB

RGB

RGB

H-STATIC

(13) H-STATIC

ROTATION

50%

50%

(12) ROTATION



KEY-BAL

50%

(11) KEY-BALANCE

To make the screen slant
to the left.

To make the screen slant
to the right.

To move the top and
bottom of the screen
image to the right.

(10) PIN-BALANCE



PIN-BAL

50%

FUNCTION AND OSD



PCC-PHASE

50%

(9) PCC-PHASE

To decrease the width at
the top of the screen
image and to increase the
width at the bottom.

To increase the width at
the top of the screen
image and to decrease
the width at the bottom.

To move the top and
bottom of the screen
image to the left.

To move the red to the
right and the blue to the
left.

To move the red to the
left and the blue to the
right.

Press plus and minus buttons together, to restore
to factory preset level.

Press plus and minus buttons together, to restore
to factory preset level.

To rotate to the left. To rotate to the right.

21

COLOR-1

COLOR-1

50%

50%

R

G
B

50%

50%

50%

50%



RGB

RGB

BALANCE

BALANCE

R

B

G

Press the select buttons (up or down)
to choose COLOR-1 R.

SELECT

Press the plus adjust button
to increase red color level.

Press the minus adjust button to
decrease the red color level.

Press the select buttons
(right or left) to choose
COLOR-1, COLOR-2,
and COLOR-3.

SELECT

50%

(14) COLOR 1-RED, COLOR 2-RED, COLOR 3-RED

Press the select buttons
(right or left) to choose
COLOR-1, COLOR-2,
and COLOR-3.

(15) COLOR 1-GREEN, COLOR 2-GREEN, COLOR 3-GREEN

50%

SELECT

SELECT

COLOR-1

COLOR-1

50%

50%

R

G

B

50%

50%

50%

50%



RGB

RGB

BALANCE

BALANCE

R

B

G

Press the select buttons (up or down)
to choose COLOR-1 G.

Press the minus adjust button to
decrease the green color level.

Press the plus adjust button to
increase the green color level.

Press the select buttons
(right or left) to choose
COLOR-1, COLOR-2,
and COLOR-3.

50%

SELECT

SELECT

Press the plus adjust button to
increase the blue color level.

Press the minus adjust button to
decrease the blue color level.

Press the select buttons (up or down)
to choose COLOR-1 B.

(16) COLOR 1-BLUE, COLOR 2-BLUE, COLOR 3-BLUE

Press the up or down SELECT buttons to choose POWER-SAVE.
Press the minus adjust button to select the constant power-on mode.
Press the plus adjust button to select the power-save mode.

(17) POWER-SAVE (ON/OFF)

(18) MOIRE-CLEAR (ON/OFF)

POWER-SAVE

POWER-SAVE

MOIRE-CLEAR

MOIRE-CLEAR

LEVEL

LEVEL

ON

ON

OFF

OFF

POWER-SAVE

MOIRE-CLEAR



ONONOFFOFF

LEVEL

POWER-SAVE

POWER-SAVE

MOIRE-CLEAR

MOIRE-CLEAR



LEVEL

LEVEL

50%

50%

Press the up or down SELECT buttons to choose MOIRE-CLEAR.
Press the minus adjust button to select the moire-clear mode off.
Press the plus adjust button to select the moire-clear mode on.

(19) MOIRE-CLEAR LEVEL

Press the up or down SELECT buttons to choose MOIRE-CLEAR LEVEL.
Press the minus adjust button to decrease the level of the moire-clear

wave.
Press the plus adjust button to increase the level of the moire-clear wave.
* The over-adjustment might degrade picture quality.

COLOR1

COLOR1

50%

50%

R
G

B

50%

50%

50%

50%



RGB

RGB

BALANCE

BALANCE

R

B

G

22

NORMAL

NORMAL

CONTRAST

CONTRAST

BRIGHT

BRIGHT

CONNECTOR

CONNECTOR

50%

50%

SELECT

4.2 Enhanced Mode Operation

Press the button (up or down) to select the CONTRAST, and press the button (right or left) to
select ENHANCED MODE. In the ENHANCED MODE, you can adjust the following controls.

Press the Plus Adjust Button:

Press the Minus Adjust Button:

FUNCTION AND OSD

(20) H-POSI (Horizontal Position)

To move the screen to the
left.

To move the screen to
the right.

To narrow the center of
the image horizontally .

To expand the center of the
image horizontally .

To expand the width of the
screen image near the
corners.

To narrow the width of the
screen image near the
corners.

To narrow the width of the
screen image near the
corners of bottom.

To expand the width of
the screen image near the
corners of bottom.

H-POSI

H-POSI



CENTER-PCC

CORNER-PCC

CORNER-PCC

BOTTOM-PCC

BOTTOM-PCC

ENHANCED

ENHANCED

50%

H-POSI

H-POSI



CENTER-PCC

CENTER-PCC

CORNER-PCC

CORNER-PCC

BOTTOM-PCC

BOTTOM-PCC

ENHANCED

50%

(22) CORNER-PCC(Corner Pincushion or Bow Amplitude)

50%

H-POSI

CENTER-PCC

CORNER-PCC

BOTTOM-PCC

ENHANCED

50%

50%

H-POSI

H-POSI

CENTER-PCC

CENTER-PCC

CORNER

CORNER

-PCC

-PCC

BOTTOM-PCC

BOTTOM-PCC

ENHANCED

ENHANCED

H-POSI

H-POSI

CENTER-PCC

CENTER-PCC

CORNER-PCC

CORNER-PCC

BOTTOM-PCC

BOTTOM-PCC

50%

50%

ENHANCED

ENHANCED

(21) CENTER-PCC (Center Pincushion or Bow Amplitude)

(23) BOTTOM-PCC(Bottom of Corner Pincushion or Bow Amplitude)

23

FUNCTION AND OSD

To clamp the video
signal at the front of the
H-Sync pulse.

To clamp the video
signal at the back of the
H-Sync pulse.

Input Full White signal to monitor.

Press the plus or minus adjust buttons, to get
pure white at the corner of picture.

Press plus and minus buttons together to
restore to factory preset level.

(27) PURITY

To select 1.0V of video
input.

To select 0.7V of
video input.

(28) VIDEO LEVEL

(26) CLAMP PULSE POSITION

CLAMPPULSE

CLAMPPULSE

POSITION

POSITION

FRONT BACK

PURITY

PURITY

VIDEOLEVEL

VIDEOLEVEL

PURITY

50%

CLAMPPULSE

POSITION

VIDEOLEVEL

CLAMPPULSE

CLAMPPULSE

POSITION

POSITION

1.0V 0.7V

PURITY

PURITY

VIDEOLEVEL

VIDEOLEVEL

(25) PCC-SINE

(24) TOP-BALANCE

To move the top of the
image to the left.

To move the top of the
image to the right.

To move expanded part
from top to bottom.

To move expanded part
from bottom to top.

TOP-BALANCE

TOP-BALANCE

PCC-SINE

PCC-SINE

50%

50%

TOP-BALANCE

TOP-BALANCE

PCC-SINE

PCC-SINE

50%

50%

Press the Minus Adjust Button:

Press the Plus Adjust Button:

24

When the monitor has no sync signal or incorrect connection and the signal frequency is
out of range, the following CAUTION comes on the screen. Check input signal, signal
cable connection and signal frequency.

NOTE

When POWER SAVE is OFF and there is no sync signal, the following screen
is displayed.

2. POWER SAVE IS ON

ATTENTION



NOSIGNAL
HOFFVOFF

PLEASE
CHECKINPUT
SIGNALOR
CONNECTION

ON

ON

OFF

OFF



POWER-SAVE

When signal frequency is out of range, the following screen is displayed.

3. POWER SAVE IS ON OR OFF

ATTENTION



SIGNALFREQUENCYIS
OUTOFRANGE

PLEASECHANGESIGNAL

PLEASECHANGESIGNAL

TIMING

ATTENTION



NOSIGNAL
HOFFVOFF

ON

ON

OFF

OFF



POWER-SAVE

POWER-SAVE



POWER-SAVE

POWER-SAVE

(1) When POWER SAVE is ON and

there is no sync signal, the following

screen is displayed for 5 seconds.

(2) Before 2 seconds POWER SAVE

function works, the following screen
is displayed.

1. POWER SAVE IS OFF

25

5

5 TROUBLESHOOTING

Before calling your Authorized Product Support, please check that the items below are properly
connected or set.
In case of using a non-standard signal, please check the pin assignments and the signal timing of your
computer with the specification outlined in SPECIFICATION 6 and APPENDIX 7.

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

Contrast and brightness controls.

Power switch.
AC power cord disconnected.
Signal cable disconnected.
BNC cables are misconnected or the green
cable is disconnected.
Computer power switch.
Power management function is active.

BNC cables are misconnected.
Input signal frequency range is disagreement.

CGA MODE is not available.
MDA MODE is not available.

EGA MODE is not available.
BNC cables are misconnected.
(Green and composite sync. connection is
reversed)
Depress the MEMORY RESET SWITCH for a
standard signal.
Adjust H.SIZE, V.SIZE, H.POSITION, and
V.POSITION with non-standard signals.
Monitor may not be able to get full-screen image
depend on signal. In this case, please select other
resolution, or other vertical refresh timing.
Make sure you wait a few seconds after adjusting
the size of the image before changing or discon­necting the signal or powering OFF the monitor.
BNC cables are misconnected.
Input video signal level select is not at the
appropriate position for your graphics adapter
output.(0.7V or 1.0Vp-p)

PROBLEM

Front (Adjust to the
maximum brightness or
push the reset button)
Front
Rear
Rear
Check the graphics
adapter and cables
Computer
Check the power manage­ment function. (see P24)
Rear
Check the specification of
graphics adapter and
monitor

Rear

Front (OSD)

Front (OSD)

Rear
Front (OSD)

LOCATION

ITEMS TO CHECK

No
picture

Display

is missing,
center shifts, or
too small or too
large of a display
size

NOTE:

Two fine horizontal lines may be visible on the screen. This is not a fault or defect of the monitor and is normal
for all aperture grille type displays.

The fine lines are the shadows of

Damper Wires

which are used to reduce the susceptability of the

DIAMONDTRON CRT's aperture grille to shock or vibration.

LED
On

LED
Off

LED
Blinking

Display is not stable

No green
color with
BNC

Un-stable
picture

Abnormal
picture

Display is dark
or too bright

ElectronGun

Damper

Shadowof
DamperWires

ApertureGrille

ApertureGrilleType

ShadowofDamperWires

Wires

26

Size

55cm/21"(50cm/19.7" Diagonal Viewable Image)
Mask type aperture grille
Gun In-line
Deflection angle 90°

CRT Phosphors Red, Green, Blue EBU (medium

short persistence)
Aperture grille pitch 0.28mm
Face Plate

Anti-glare, Anti-reflection and Anti-static coating

Focusing method Dynamic Beam Forming (DBF)

INPUT SIGNAL Video 0.7 and 1.0Vp-p analog RGB

Sync Sync. on Green or separated H, V

sync. or Composite sync

INTERFACE Input Connector 5BNC, DB9-15P, DIN-8P(Serial Control)

Input Impedance 75 (video)

SCANNING Horizontal 30 - 95kHz
FREQUENCY Vertical 50 - 152Hz
RESOLUTION (HxV)

1600dots x 1200lines Non-Interlaced maximum addressable resolution format at 75Hz

WARM-UP TIME 30 minutes to reach optimum performance level
BRIGHTNESS 100cd/cm2, standard full white video signal

VIDEO AMPLIFIER 50Hz - 180MHz (typ.)
BLANKING TIME Horizontal ≥ 2.5 µsec (typ.)

Vertical ≥ 500 µsec (typ.)
DISPLAY SIZE 390mm x 290mm (Max.) ratio 4:3, e.g. 1024dots x 768lines
COLOR 1= 9300K, 2 = 6500K, 3 = 5000K
POWER SOURCE AC100-120V/220-240V±10% 50/60Hz 150W (typ.)
OPERATING Temperature 5 - 35°C
ENVIRONMENT Humidity 10 - 90%RH (without condensation)
CABINET (W)19.7inch x (H)19.3inch x (D)19.2inch

(W)500mm x (H)490mm x (D)488 mm
WEIGHT 35kg (77lbs.)
TILT/SWIVEL Tilt Angle -5° - +10°
BASE Swivel Angle ±45°

Safety UL1950 (UL), CSA C22.2 No.950 (C-UL)

EN60950 (TÜV-GS)

EMC FCC Class-B, DOC Class-B

EN55022 Class-B, VCCI Class-I
EN50082-1, EN61000-3-2

REGULATIONS X-Ray DHHS, HWC

Röv vom 8.1, 1987

Other CE-Marking

MPR-II
ISO 9241-3 (TÜV-ERGO)
TCO '95
ZH1/618 (TÜV-GS)
International Energy Star Program
NUTEK Spec. 803299/94
Guidelines for the Suppression of Harmonics

in Appliances and General-Use Equipment

6

6

SPECIFICATIONS

27

7

7 APPENDIX

Pin No. Signal Description

1 DTR Data Terminal Ready
2NC
3 TXD Transmit Data
4 GND Ground
5 RXD Receive Data
6 GND Ground
7NC
8NC

NC......................... NO-CONNECTION

Pin No. Signal

1 RED VIDEO
2 GREEN VIDEO

or COMPOSITE SYNC with GREEN VIDEO
3 BLUE VIDEO
4 GROUND
5 DDC GROUND
6 RED GROUND
7 GREEN GROUND
8 BLUE GROUND
9NC

10 SYNC GROUND
11 GROUND
12 SDA
13 HORIZONTAL SYNC

or COMPOSITE SYNC
14 VERTICAL SYNC(VCLK)
15 SCL

7.1 Monitor Signal Input Connector (DB9-15P)

MOUNTED ON THE REAR PANEL

5 4

3

2 1

10

11


12

13

14

15

67

8

9

(Female)

DB9-15P

DDC ............... DISPLAY DATA CHANNEL

SDA ............... SERIAL DATA

SCL ................ SERIAL CLOCK

NC.................. NO-CONNECTION

PIN ASSIGNMENTS

8

5

4

3

2

1

7

6

7.2 Serial Interface Input Connector (DIN-8P) For Serial Interface Function

(Female)

DIN-8P

MOUNTED ON THE REAR PANEL

PIN ASSIGNMENT

28

7.3 SC-B102 Signal Cable

PIN ASSIGNMENT AND SIGNAL LEVEL

Approx. 1.8m

DB9-15P DB9-15P
(Male) (Male)

Wire : 5 coaxial

SIGNAL LEVEL

NC ..................... NO-CONNECTION

DDC: DISPLAY DATA CHANNEL
SDA: SERIAL DATA
SCL: SERIAL CLOCK

SIGNAL

PIN ANALOG
ASSIGNMENT

1 RED
2 GREEN
3 BLUE
4 GROUND
5 DDC GROUND
6 RED GROUND
7 GREEN GROUND
8 BLUE GROUND
9NC
10 SYNC GROUND
11 GROUND
12 SDA
13 HORIZONTAL SYNC
14 VERTICAL SYNC(VCLK)
15 SCL

432

1

10

11


13 14

6 7

8

5

9

12 15

29

7.4 Macintosh Adapter AD-A205 settings

The AD-A205 Macintosh Adapter allows you to take advantage of the built in video capabilities of
your Macintosh computer with the monitor.

(1) Set dip switches of adapter, before connect to the computer.
(2) Set dip switches according to the following chart.

By using the following chart, you can choose a main resolution, quickly.
If you wish to operate by other resolution, refer to next page; "AD-A205 Mac Adapter setting
chart"

O

N

ON

1 2 3

4

5 6

AD

-A205

MITSUBISHI

O

N

O

FF

Macintosh

DIP Switches

Display Monitor

(3) "AD-A205 Mac Adapter setting chart" shows all available modes for Macintosh systems and

all possible combinations with the monitor.
However, we recommend you to use the monitor with a preset timing. (See 1.2 Internal Preset
Memory Capability)

(4) Please refer to instruction book of your computer about resolution setting.

Resolution may not be changed on some computers.

1. Resolution does not change with the computer powered on when you set dip switches.
Be sure to power off the computer when you set dip switches.

2.

Set dip switches by pointed article like pencils or ball paint pen to touch end of switch groove.

Macintosh IIsi, IIci, IIvi, IIvx, LC, LC II

Macintosh LC III, LC475, LC630

Macintosh Quadra 610, 650, 700, 800, 840AV, 900, 950
Macintosh Centris 610, 650, 660AV

Performa 6260, 6310, 6410, 6420
Power Macintosh 6100, 6100AV, 6200, 6300
Power Macintosh 7100AV, 7200, 7300, 7500, 7600
Power Macintosh 8100, 8100AV, 8500, 8600
Power Macintosh 9500, 9600
Workgroup Server 7350, 8150, 9150, 9650

Power Macintosh 4400, G3

1,2

2,4

1,2,3,4

1,2,6

3,4

NOTE

Apple Macintosh

Switch

ON

Switch Setting

30

640 x480@60Hz

640 x480@67Hz

640 x480@67Hz

640 x480@72Hz

640 x480@75Hz

640 x480@85Hz

800 x600@60Hz

800 x600@72Hz

800 x600@75Hz

800 x600@85Hz

832 x624@75Hz

832 x624@75Hz

1024 x768@60Hz

1024 x768@70Hz

1024 x768@72Hz

1024 x768@75Hz

1024 x768@75Hz

1024 x768@85Hz

1152 x870@75Hz

1152 x870@75Hz

1280 x960@60Hz

1280 x960@75Hz

1280 x960@85Hz

1280 x1024@60Hz

1280 x1024@75Hz

1280 x1024@85Hz

1600 x1200@60Hz

1600 x1200@65Hz

1600 x1200@67Hz

1600 x1200@70Hz

1600 x1200@75Hz

IIsi

IIci

IIvi

IIvx

LC

LCII

LCIII

LC475

LC630 Quadra

700

900

Quadra

610

650

800

950

Centris

610

650

Quadra

840AV

Centris

660AV

6260

6310

6410

6420

Workgroup

Server

8150

9150

6100

8100

6100AV

7100AV

8100AV

DRAM

Video Port

(HDI-45)

6200

6300

7200 4400

7300

7500

7600

8500

8600

Workgroup

Server

7350

9500

9600/233

Workgroup

Server

9650

9600/300

9600/350

G3

Macintosh

Performa Power Macintosh

8100

VRAM

Video Card

(DB-15)

6100AV

7100AV

8100AV

AV

Video Card

(DB-15)

1,2 1,2 1,2 1,2 1,2 1,2

3,4

1,2 1,2 1,2,6 1,2,6

3,4 3,4 3,4 3,4 3,4 3,4 1,2,6 1,2,6 3,4 3,4

3,4

3,4 3,4 3,4 3,4 3,4

3,4

3,4

3,4

3,4

3,4

3,4

3,4

3,4

3,4

3,4

3,4

3,4

3,4

3,4

1,2,6

3,4

3,4

3,4

3,4

3,4

3,4

1,2,6

3,4

3,4

3,41,2,6

1,2,6

1,2,6

1,2,61,2,6

3,4

1,2,6

1,2,6

3,4

3,4

3,4

3,4

3,43,4

1,2,6 1,2,6 1,2,6 1,2,61,2,61,2,63,4

3,4

3,4

3,4

3,4

3,4

3,4

3,4

3,4

3,4

3,4

3,4

3,4

3,4

3,4

3,4

3,4

3,4

1,2,6

1,2,63,4

1,2,6

3,4

3,4

1,2,6

1,2,6

3,4

1,2,6

3,4

3,4

3,4

1,2,61,2,6

1,2,6

1,2,6

1,2,6

3,4

1,2,6

3,4

1,2,6

3,4

1,2,6

3,4

3,4

3,4

1,2,6

3,4

1,2,6

1,2,6

3,4

3,4

2,42,4 2,4 2,4 2,4 1,2,6 1,2,6

1,2,63,4

3,4

2,32,3

1,2,3,4 1,2,3,4 1,2,3,4

1,2,6

1,2,6

1,2,6 1,2,63,4

1,2,6 1,2,6

3,4

3,4

3,43,4

1,2,6 3,4 3,4

1,2,61,2,63,4

3,4 3,4

1,2,6

1,2,63,41,2,61,2,6

1,2,6

1,2,6 3,4

1,2,6

1,2,6

解像度

(RESOLUTION)

＜AD-A205 Mac Adapter Setting Chart

＞

● Set dip switch "ON" as shown below.（Example："1,2" )

CP871C134B50

MITSUBISHI ELECTRIC CORPORATION
HEAD OFFICE: MITSUBISHI DENKI BLD, MARUNOUCHI, TOKYO 100-0005.
TELEX J24532 CABLE MELCO TOKYO