Mitsubishi Electronics R410A User Manual

Air-Conditioners OUTDOOR UNIT

PUMY-P·NHMU (-BS)

For use with R410A

INSTALLATION MANUAL

For safe and correct use, read this manual and the indoor unit installation manual thoroughly before installing the air-conditioner unit.

MANUAL DE INSTALACIÓN

Para un uso correcto y seguro, lea detalladamente este manual y el manual de instalación de la unidad interior antes de instalar la unidad de aire acondicionado.

MANUEL D’INSTALLATION

Avant d’installer le climatiseur, lire attentivement ce manuel, ainsi que le manuel d’installation de l’appareil intérieur pour une utilisation sûre et correcte.

FOR INSTALLER

PARA EL INSTALADOR

POUR L’INSTALLATEUR

English

Español

Français

Contents

1. Safety precautions ................................................................................... 2

2. Installation location .................................................................................. 3

3. Installing the outdoor unit......................................................................... 5

4. Installing the refrigerant piping................................................................. 5

Confirmation of parts attached

In addition to this manual, the following parts are supplied with the outdoor unit. They are used for grounding the S terminals of transmission terminal blocks TB3, TB7. For details refer to “6. Electrical work”.

1. Safety precautions

s Before installing the unit, make sure you read all the “Safety precau-

tions”.

s Please report to or take consent by the supply authority before connec-

tion to the system.

Warning: Describes precautions that must be observed to prevent danger of injury or death to the user.

Caution: Describes precautions that must be observed to prevent damage to the unit.

Warning:

• The unit must not be installed by the user. Ask a dealer or an authorized

technician to install the unit. If the unit is installed incorrectly, water leakage, electric shock, or fire may result.

• For installation work, f ollow the instructions in the Installation Manual and use

tools and pipe components specifically made for use with R410A refrigerant. The R410A refrigerant in the HFC system is pressurized 1.6 times the pressure of usual refrigerants. If pipe components not designed for R410A refrigerant are used and the unit is not installed correctly, the pipes may burst and cause damage or injuries. In addition, water leaka ge, electric shock, or fire may result.

• The unit must be installed according to the instructions in or der to minimize

the risk of damage from earthquakes, typhoons, or strong winds. An incorrectly installed unit may fall down and cause damage or injuries.

• The unit must be securely installed on a structure that can sustain its weight.

If the unit is mounted on an unstable structure, it may fall down and cause damage or injuries.

• If the air conditioner is installed in a small room, measures must be taken to

prevent the refrigerant concentration in the room from exceeding the safety limit in the event of refrigerant leakage. Consult a dealer regarding the appropriate measures to prevent the allowable concentration from being exceeded. Should the refrigerant leak and cause the concentration limit to be exceeded, hazards due to lack of oxygen in the room may result.

• Ventilate the room if refrigerant leaks during operation. If refrigerant comes

into contact with a flame, poisonous gases will be released.

• All electric work must be performed by a qualified technician according to

local regulations and the instructions given in this manual. The units must be powered by dedicated power lines and the correct volta ge and cir cuit breakers must be used. Power lines with insufficient capacity or incorrect electrical work may result in electric shock or fire.

5. Drainage piping work ............................................................................... 8

6. Electrical work.......................................................................................... 8

7. Test run ................................................................................................... 1 1

Grounding lead wire (× 2)

After installation work has been completed, explain the “Safety Precautions”, use, and maintenance of the unit to the customer according to the information in the Operation Manual and perform the test run to ensure normal operation. Both the Installation Manual and Operation Manual must be given to the user for keeping. These manuals must be passed on to subsequent users.

: Indicates a part which must be grounded.

Warning:

Carefully read the labels affixed to the main unit.

• Use C1220 copper phosphorus, for copper and copper allo y seamless pipes, to connect the refrigerant pipes. If the pipes are not connected correctly, the unit will not be properly grounded and electric shock may result.

• Use only specified cables for wiring. The connections must be made securely without tension on the terminals. If the cables are connected or installed incorrectly, overheating or fire may result.

• The terminal block cover panel of the outdoor unit must be firml y attached. If the cover panel is mounted incorrectly and dust and moisture enter the unit, electric shock or fire may result.

• When installing or moving the air conditioner , use only the specified refrigerant (R410A) to charge the refrigerant lines. Do not mix it with any other refrigerant and do not allow air to remain in the lines. Air enclosed in the lines can cause pressure peaks resulting in a rupture and other hazards.

• Use only accessories authorized by Mitsubishi Electric and ask a dealer or an authorized technician to install them. If accessories are incorrectly installed, water leakage, electric shock, or fire may result.

• Do not alter the unit. Consult a dealer for repair s. If alterations or repairs are not performed correctly, water leakage, electric shock, or fire may result.

• The user should never attempt to repair the unit or transfer it to another location. If the unit is installed incorrectly, water leakage, electric shock, or fire may result. If the air conditioner must be repaired or moved, ask a dealer or an authorized technician.

• After installation has been completed, check for refrigerant leaks. If refrigerant leaks into the room and comes into contact with the flame of a heater or portable cooking range, poisonous gases will be released.

1.1. Before installation

Caution:

• Do not use the unit in an unusual environment. If the air conditioner is installed in areas exposed to steam, v olatile oil (including machine oil), or sulfuric gas, areas exposed to high salt content such as the seaside, or areas where the unit will be covered by snow, the performance can be significantly reduced and the internal parts can be damaged.

• Do not install the unit where combustible gases may leak, be pr oduced, flow, or accumulate. If combustible gas accum ulates around the unit, fire or explosion may result.

• The outdoor unit produces condensation during the heating operation. Make sure to provide drainage around the outdoor unit if such condensation is likely to cause damage.

1.2. Before installation (relocation)

Caution:

• Be extremely careful when transporting the units. Two or more persons are needed to handle the unit, as it weighs 20 kg [44 lbs] or more. Do not grasp the packaging bands. Wear protective gloves to remove the unit from the packaging and to move it, as you can injure your hands on the fins or other parts.

• Be sure to safely dispose of the packaging materials. Packaging materials, such as nails and other metal or wooden parts may cause stabs or other injuries.

• The base and attachments of the outdoor unit must be periodically chec ked for looseness, cracks or other damage. If such defects are left uncorrected, the unit may fall down and cause damage or injuries.

• When installing the unit in a hospital or communications office, be prepared for noise and electronic interference. Inverters, home appliances, high-frequency medical equipment, and radio communications equipment can cause the air conditioner to malfunction or breakdown. The air conditioner may also affect medical equipment, disturbing medical care, and comm unications equipment, harming the screen display quality.

• Do not clean the air conditioner unit with water. Electric shock may result.

• Tighten all flare nuts to specification using a torque wrench. If tightened too much, the flare nut can break after an extended period and refrigerant can leak out.

37-13/32

13+1-3/16

53-5/32

6-7/8

23-5/8

14-9/16

1. Safety precautions

1.3. Before electric work

Caution:

• Be sure to install circuit breakers. If not installed, electric shock may result.

• For the power lines, use standard cables of sufficient capacity. Otherwise, a

short circuit, overheating, or fire may result.

• When installing the power lines, do not apply tension to the cables. If the connections are loosened, the cables can snap or break and overheating or fire may result.

1.4. Before starting the test run

Caution:

• T urn on the main power s witch more than 12 hours before starting operation. Starting operation just after turning on the power switch can severely damage the internal parts. Keep the main power switch turned on during the operation season.

• Before starting operation, check that all panels, guards and other protective parts are correctly installed. Rotating, hot, or high voltage parts can cause injuries.

1.5. Using R410A refrigerant air conditioners

Caution:

• Use C1220 copper phosphorus, for copper and copper alloy seamless pipes, to connect the refrigerant pipes. Make sure the insides of the pipes are clean and do not contain any harmful contaminants such as sulfuric compounds, oxidants, debris, or dust. Use pipes with the specified thickness. (Refer to page

5) Note the following if reusing existing pipes that carried R22 refrigerant.

- Replace the existing flare nuts and flare the flared sections again.

- Do not use thin pipes. (Refer to page 5)

• Store the pipes to be used during installation indoors and keep both ends of the pipes sealed until just before brazing. (Leave elbow joints, etc. in their packaging.) If dust, debris, or moisture enters the refrigerant lines, oil deterioration or compressor breakdown may result.

• Use ester oil, ether oil, alkylbenzene oil (small amount) as the refrigeration oil applied to the flared sections. If mineral oil is mixed in the refrigeration oil, oil deterioration may result.

• Be sure to ground the unit. Do not connect the ground wire to gas or water pipes, lighting rods, or telephone grounding lines. If the unit is not properly grounded, electric shock may result.

• Use circuit breakers (ground fault interrupter, isolating switch (+B fuse), and molded case circuit breaker) with the specified capacity . If the circuit breaker capacity is larger than the specified capacity, breakdown or fire may result.

• Do not touch any switch with wet hands. Electric shock may result.

• Do not touch the refrigerant pipes with bare hands during operation. The

refrigerant pipes are hot or cold depending on the condition of the flowing refrigerant. If you touch the pipes, burns or frostbite may result.

• After stopping operation, be sure to wait at least five minutes before turning off the main power switch. Otherwise, water leakage or breakdown may result.

• Do not use refrigerant other than R410A refrigerant. If another refrigerant is used, the chlorine will cause the oil to deteriorate.

• Use the following tools specifically designed for use with R410A refrigerant. The following tools are necessary to use R410A refrigerant. Contact your nearest dealer for any questions.

Tools (for R410A)

Gauge manifold Flare tool

Charge hose Size adjustment gauge

Gas leak detector Vacuum pump adapter

Torque wrench Electronic refrigerant charging scale

• Be sure to use the correct tools. If dust, debris, or moisture enters the refrigerant lines, refrigeration oil deterioration may result.

• Do not use a charging cylinder. If a charging cylinder is used, the composition of the refrigerant will change and the efficiency will be lowered.

1.6. Precautions for salt damage–resistant model (“-BS” model)

Although this product (only “-BS” model) has been designed to be resistant to salt damage, observe the following precautions to maintain the performance of the unit.

1.Avoid installing the unit in a location where it will be exposed directly to sea water or

sea breeze.

2.If the cover panel may become covered with salt, be sure to install the unit in a

location where the salt will be washed away by rainwater. (If a sunshade is installed, it may be difficult for rainwater to clean the panel.)

2. Installation location

2.1. Refrigerant pipe

Refer to Fig. 4-1.

2.2. Choosing the outdoor unit installation location

• Avoid locations exposed to sources of heat.

• Select a location from which noise emitted by the unit will not inconvenience neighbors.

• Select a location permitting easy wiring and pipe access to the power source and

indoor unit.

• Avoid locations where comb ustible gases ma y leak, be produced, flow , or accum ulate.

• Note that water may drain from the unit during operation.

• Select a level location that can bear the weight and vibration of the unit.

Fig. 2-1

(inch)

3.To ensure that w ater does not collect in the base of the outdoor unit, make sure that the base is level, not at angle. Water collecting in the base of the outdoor unit could cause rust.

4.If the unit is installed in a coastal area, clean the unit with water regularly to remove any salt build-up.

5.If the unit is damaged during installation or maintenance, be sure to repair it.

6.Be sure to check the condition of the unit regularly.

7.Be sure to install the unit in a location with good drainage.

• Avoid locations where the unit can be co vered by sno w. In areas where hea vy snow f all is anticipated, special precautions such as raising the installation location or installing a hood on the air intake must be taken to prevent the snow from blocking the air intake or blowing directly against it. This can reduce the airflow and a malfunction may result.

• Avoid locations exposed to oil, steam, or sulfuric gas.

• Use the transportation handles of the outdoor unit to transport the unit. If the unit is

carried from the bottom, hands or fingers may be pinched.

2.3. Outline dimensions (Outdoor unit) (Fig. 2-1)

Constraints on indoor unit installation

You should note that indoor units that can be connected to this outdoor unit are the following models.

• Indoor units with model numbers P06-P54 (PUMY-P36 : P06-P36) can be connected. Refer to the tab le below for possib le 1-8 (PUMY-P36 : 1-6) room, indoor unit combinations.

Verification

The rated capacity should be determined by observing the table below. The unit’s quantities are limited in 1 to 8 units. For the next step, make sure that the total rated capacity selected will stay in a range of 50% - 130% of the outdoor unit capacity.

• PUMY-P36 18,000 - 46,800 Btu/h

• PUMY-P48 24,000 - 62,400 Btu/h

Indoor unit type P06 P08 P12 P15 P18 P24 P30 P36 P48 P54 Rated capacity (Cooling) (Btu/h)

Combinations in which the total capacity of indoor units exceeds the capacity of the outdoor unit will reduce the cooling capacity of each indoor unit below their rated cooling capacity. Thus, combine indoor units with an outdoor unit within the outdoor unit’s capacity, if possible.

6,000 8,000 12,000 15,000 18,000 24,000 30,000 36,000 48,000 54,000

5-29/32

11-13/16

39-3/8

Max. 19-11/16

7-7/8

11-13/16

7-7/8

39-3/8

5-29/32

39-3/8

9-27/32

59-1/16

19-11/16

Max. 19-11/16

11-13/16

59-1/16

19-11/16

59-1/16

Max. 11-13/16

59-1/16

19-11/16

39-3/8

23-5/8

78-24/32

5-29/32

59-1/16

23-5/8

118-4/32

19-11/16

59-1/16

31-1/2

5-29/32

2. Installation location

2.4. Ventilation and service space

2.4.1. When installing a single outdoor unit

Minimum dimensions are as follows, e xcept for Max., meaning Maximum dimensions, indicated. Refer to the figures for each case.

1 Obstacles at rear only (Fig. 2-2) 2 Obstacles at rear and above only (Fig. 2-3)

• Do not install the optional air outlet guides for upward airflow.

3 Obstacles at rear and sides only (Fig. 2-4) 4 Obstacles at front only (Fig. 2-5)

∗ When using an optional air outlet guide, the clearance is 500 mm [19-11/16 inch] or more.

5 Obstacles at front and rear only (Fig. 2-6)

∗ When using an optional air outlet guide, the clearance is 500 mm [19-11/16 inch] or more.

6 Obstacles at rear, sides, and above only (Fig. 2-7)

• Do not install the optional air outlet guides for upward airflow.

2.4.2. When installing multiple outdoor units

Leave 10 mm [13/32 inch] space or more between the units.

1 Obstacles at rear only (Fig. 2-8) 2 Obstacles at rear and above only (Fig. 2-9)

• No more than three units must be installed side by side. In addition, leave space as shown.

• Do not install the optional air outlet guides for upward airflow.

3 Obstacles at front only (Fig. 2-10)

∗ When using an optional air outlet guide, the clearance is 1000 mm [39-3/8 inch] or more.

4 Obstacles at front and rear only (Fig. 2-11)

∗ When using an optional air outlet guide, the clearance is 1000 mm [39-3/8 inch] or more.

5 Single parallel unit arrangement (Fig. 2-12)

∗ When using an optional air outlet guide installed for upward airflow, the clearance is 1000

mm [39-3/8 inch] or more.

6 Multiple parallel unit arrangement (Fig. 2-13)

∗ When using an optional air outlet guide installed for upward airflow, the clearance is 1500

mm [59-1/16 inch] or more.

7 Stacked unit arrangement (Fig. 2-14)

• The units can be stacked up to two units high.

• No more than two stacked units must be installed side b y side. In addition, leave space as shown.

(inch)

Fig. 2-6

Fig. 2-9

Fig. 2-3

Fig. 2-5Fig. 2-4Fig. 2-2

Fig. 2-7

Fig. 2-8

Fig. 2-10 Fig. 2-11

Fig. 2-12 Fig. 2-13 Fig. 2-14

Max. 1-3/16

2. Installation location

23-5/8 23-5/8Min. 14-6/32

Min. 13/32

37-13/32

63/64

14-9/16

6-7/8 6-7/8

2.4.3. Windy location installation

When installing the outdoor unit on a rooftop or other location unprotected from the wind, situate the air outlet of the unit so that it is not directly exposed to strong winds. Strong wind entering the air outlet may impede the normal airflow and a malfunction may result. The following shows two examples of precautions against strong winds. 1 Install an optional air guide if the unit is installed in a location where strong winds

from a typhoon, etc. may directly enter the air outlet. (Fig. 2-15)

A Air guide

2 Position the unit so that the air outlet blows perpendicularly to the seasonal wind

direction, if possible. (Fig. 2-16)

B Wind direction

Fig. 2-15

3. Installing the outdoor unit

A M10 (3/8") bolt B Base C As long as possible. D Vent

Fig. 2-16

(inch)

• Be sure to install the unit in a sturdy, level surface to prevent rattling noises during operation. (Fig. 3-1)

Foundation bolt M10 (3/8") Thickness of concrete 120 mm [4-23/32 inch] Length of bolt 70 mm [2-3/4 inch] Weight-bearing capacity 320 kg [705 lbs]

• Make sure that the length of the foundation bolt is within 30 mm [1-3/16 inch] of the bottom surface of the base.

• Secure the base of the unit firmly with four-M10 foundation bolts in sturdy locations.

Installing the outdoor unit

• Do not block the vent. If the vent is blocked, operation will be hindered and breakdown may result.

• In addition to the unit base, use the installation holes on the back of the unit to attach wires, etc., if necessary to install the unit. Use self-tapping screws (ø5 × 15 mm [ø13/16 × 19/32 inch] or less) and install on site.

Warning:

• The unit must be securely installed on a structure that can sustain its weight. If the unit is mounted on an unstable structure, it may fall down and cause damage or injuries.

• The unit must be installed according to the instructions in order to minimize the risk of damage from earthquakes, typhoons, or strong winds. An incorrectly installed unit may fall down and cause damage or injuries.

4. Installing the refrigerant piping

Fig. 3-1

4.1. Precautions for devices that use R410A refrigerant

• Refer to page 3 for precautions not included below on using air conditioner s with R410A refrigerant.

• Use ester oil, ether oil, alkylbenzene oil (small amount) as the refrigeration oil applied to the flared sections.

• Use C1220 copper phosphorus, for copper and copper allo y seamless pipes, to connect the refrigerant pipes. Use refrigerant pipes with the thicknesses specified in the table to the below. Make sure the insides of the pipes are clean and do not contain any harmful contaminants such as sulfuric compounds, oxidants, debris, or dust.

Warning: When installing or moving the air conditioner, use only the specified refrigerant (R410A) to charge the refrigerant lines. Do not mix it with any other refrigerant and do not allow air to remain in the lines. Air enclosed in the lines can cause pressure peaks resulting in a rupture and other hazards.

Indoor unit type P06-P18 P24-P54

Liquid pipe

Gas pipe

• Do not use pipes thinner than those specified above.

ø6.35 mm [1/4 inch] ø9.52 mm [3/8 inch]

thickness 0.8 mm [1/32 inch] thickness 0.8 mm [1/32 inch]

ø12.7 mm [1/2 inch] ø15.88 mm [5/8 inch]

thickness 0.8 mm [1/32 inch] thickness 1.0 mm [5/128 inch]

B C

ahb c

90° ±0.5°

øA

R0.4~R0.8

45°±2°

4. Installing the refrigerant piping

A+a+b+c+d = 120 m [394 ft] L = A+d = 80 m [262 ft], R= d = 30 m [100 ft] H = 30 m [100 ft] (Outdoor lower H = 20 m [70 ft]) h = 12 m [39 ft]

A Flare cutting dimensions B Flare nut tightening torque

A+B+C+a+b+c+d = 120 m [394 ft] L = A+B+C+d = 80 m [262 ft] R= B+C+d = 30 m [100 ft] H = 30 m [100 ft] (Outdoor lower H = 20 m [70 ft]) h = 12 m [39 ft]

A : Outdoor Unit B : First Branch C : Indoor unit

Fig. 4-1

(inch)

A (mm [inch])

Å Liquid pipe ı Gas pipe

PUMY ø9.52 [3/8] ø15.88 [5/8]

B, C, D (mm [inch])

Ç Total capacity of indoor units Å Liquid pipe ı Gas pipe

ø9.52 [3/8] ø15.88 [5/8]

a, b, c, d, e, f (mm [inch])

Î Model number Å Liquid pipe ı Gas pipe P06, P08, P12, P15, P18 ø6.35 [1/4] ø12.7 [1/2] P24, P30, P36, P48, P54 ø9.52 [3/8] ø15.88 [5/8]

‰ Branch kit model

CMY-Y62-G-E

Ï 4-Branching header Ì 8-Branching header

CMY-Y64-G-E CMY-Y68-G-E

4.2. Connecting pipes (Fig. 4-2)

Fig. 4-1 is a sample of piping system.

• When commercially available copper pipes are used, wrap liquid and gas pipes with commercially available insulation materials (heat-resistant to 100°C [212°F] or more, thickness of 12 mm [1/2 inch] or more).

• The indoor parts of the drain pipe should be wrapped with polyethylene foam insulation materials (specific gravity of 0.03, thickness of 9 mm [23/64 inch] or more).

• Apply thin layer of refrigerant oil to pipe and joint seating surf ace before tightening flare nut. A

• Use two wrenches to tighten piping connections. B

• Use leak detector or soapy water to check f or gas leaks after connections are com-

pleted.

• Apply refrigerating machine oil over the entire flare seat surface. C

• Use the flare nuts for the following pipe size. D

(mm [inch])

Indoor unit Outdoor unit

P06-P18 P24-P54 P48

Gas side Pipe size ø12.7 [1/2] ø15.88 [5/8] ø15.88 [5/8]

Liquid side Pipe size ø6.35 [3/8] ø9.52 [3/8] ø9.52 [3/8]

Fig. 4-2

A (Fig. 4-2)

Copper pipe O.D. Flare dimensions

øA dimensions

ø6.35 [1/4] 8.7 - 9.1 [11/32-23/64] ø9.52 [3/8] 12.8 - 13.2 [1/2-33/64] ø12.7 [1/2] 16.2 - 16.6 [41/64-21/32]

ø15.88 [5/8] 19.3 - 19.7 [49/64-25/32]

B (Fig. 4-2)

Copper pipe O.D. Flare nut O.D. Tightening torque

(mm [inch]) (mm [inch]) (N·m [ft·lbs])

ø6.35 [1/4] 17 [43/64] 14 - 18 [10-13] ø6.35 [1/4] 22 [7/8] 34 - 42 [25-30] ø9.52 [3/8] 22 [7/8] 34 - 42 [25-30] ø12.7 [1/2] 26 [1-3/64] 49 - 61 [35-44]

ø12.7 [1/2] 29 [1-9/64] 68 - 82 [49-59] ø15.88 [5/8] 29 [1-9/64] 68 - 82 [49-59] ø15.88 [5/8] 36 [1-27/64] 100 - 120 [71-87]

(mm [inch])

A Die B Copper pipe

Fig. 4-3

• When bending the pipes, be careful not to break them. Bend radius of 100 mm [315/16 inch] to 150 mm [5-27/32 inch] is sufficient.

• Make sure the pipes do not contact the compressor. Abnormal noise or vibration may result.

1 Pipes must be connected starting from the indoor unit.

Flare nuts must be tightened with a torque wrench.

2 Flare the liquid pipes and gas pipes and apply a thin layer of refrigeration oil

(Applied on site).

• When usual pipe sealing is used, refer to Table 1 for flaring of R410A refrigerant pipes. The size adjustment gauge can be used to confirm A measurements.

Table 1 (Fig. 4-3)

Copper pipe O.D. A (mm [inch])

(mm [inch]) Clutch type

ø6.35 [1/4] 1.0 - 1.5 [3/64-1/16] ø9.52 [3/8] 1.0 - 1.5 [3/64-1/16] ø12.7 [1/2] 1.0 - 1.5 [3/64-1/16]

ø15.88 [5/8] 1.0 - 1.5 [3/64-1/16]

4. Installing the refrigerant piping

C D

E F

A Front piping cover B Piping cover C Stop valve D Service panel E Bend radius : 100 mm - 150 mm

Fig. 4-4

A Stop valve <Liquid side> B Stop valve <Gas side> C Service port D Open/Close section E Local pipe

F Sealed, same way for gas side G Pipe cover H Do not use a wrench here.

Refrigerant leakage may result.

I Use two wrenches here.

Fig. 4-5

4.3. Refrigerant piping (Fig. 4-4)

Remove the service panel D (three screws) and the front piping cover A (two screws) and rear piping cover B (two screws). 1 Perform refrigerant piping connections for the indoor/outdoor unit when the out-

door unit’s stop valve is completely closed.

2 Vacuum-purge air from the indoor unit and the connection piping. 3 After connecting the refrigerant pipes, check the connected pipes and the indoor

unit for gas leaks. (Refer to 4.4 Refrigerant pipe airtight testing method)

4 Vacuumize the refrigerant lines through the service port of the liquid and gas stop

valves. And then open the stop v alves completely (f or both the liquid and gas stop valves). This will completely connect the refrigerant lines of the indoor and outdoor units.

• If the stop valves are left closed and the unit is operated, the compressor and control valves will be damaged.

• Use a leak detector or soapy water to check for gas leaks at the pipe connection sections of the outdoor unit.

• Do not use the refrigerant from the unit to purge air from the refrigerant lines.

• After the valve work is completed, tighten the valve caps to the correct torque:

20 to 25 N·m [14 to 18 ft·lbs] (200 to 250 kgf·cm). Failure to replace and tighten the caps may result in refrigerant leakage. In addition, do not damage the insides of the valve caps as they act as a seal to prevent refrigerant leakage.

5 Use sealant to seal the ends of the thermal insulation around the pipe connection

sections to prevent water from entering the thermal insulation.

4.4. Refrigerant pipe airtight testing method

(1)Connect the testing tools.

• Make sure the stop valves A B are closed and do not open them.

• Add pressure to the refr igerant lines through the service por t C of the liquid

stop valve A and the gas stop valve B.

(2) Do not add pressure to the specified pressure all at once; add pressure little by little .

1 Pressurize to 0.5 MPa [73 PSIG], wait five minutes, and make sure the

pressure does not decrease.

2 Pressurize to 1.5 MPa [218 PSIG], wait five minutes, and make sure the pres-

sure does not decrease.

3 Pressurize to 3.8 MPa [550 PSIG] and measure the surrounding temperature

and refrigerant pressure.

(3)If the specified pressure holds for about one day and does not decrease, the pipes

have passed the test and there are no leaks.

• If the surrounding temperature changes by 1°C [1.8°F], the pressure will change

by about 0.01 MPa [1.5 PSIG]. Make the necessary corrections.

(4) If the pressure decreases in steps (2) or (3), there is a gas leak. Look for the

source of the gas leak.

(1)

Type A Type B

(2) 1

Fig. 4-6

Fig. 4-7

4.5. Stop valve opening method

(1)Gas side (Fig. 4-6) Type A 1 Remove the cap, then turn one-quarter rotation counter-clockwise with a flat-bladed

screwdriver to complete open.

2 Check that the valves are fully open, then return the cap to its original state and

tighten it down. Type B 1 Remove the cap, pull the handle toward you and rotate 1/4 turn in a counterclock-

wise direction to open. 2 Make sure that the stop valve is open completely, push in the handle and rotate

the cap back to its original position. (2)Liquid side (Fig. 4-7) 1 Remove the cap and turn the valve rod counterclockwise as far as it will go with

the use of a 4 mm [5/32 inch] hexagonal wrench. Stop turning when it hits the

stopper.

(ø6.35 [1/4 inch]: Approximately 4.5 revolutions) (ø9.52 [3/8 inch]: Approximately

10 revolutions) 2 Make sure that the stop valve is open completely, push in the handle and rotate

the cap back to its original position.

A Valve

B Unit side

C Handle

D Cap

E Local pipe side

Refrigerant pipes are protectively wrapped

• The pipes can be protectively wrapped up to a diameter of ø90 mm [ø3-35/64 inch]

before or after connecting the pipes. Cut out the knockout in the pipe cover following the groove and wrap the pipes.

Pipe inlet gap

• Use putty or sealant to seal the pipe inlet around the pipes so that no gaps remain.

(If the gaps are not closed, noise may be emitted or water and dust will enter the unit and breakdown may result.)

F Open position side G Service port H Wrench hole I Refrigerant flow direction J Operation section

4. Installing the refrigerant piping

* The figure to the left is an example only.

The stop valve shape, service port position, etc., may vary according to the model.

* Turn section A only.

(Do not further tighten sections A and

B together. )

C Charge hose D Service port

Fig. 4-8

4.6. Additional refrigerant charge

Refrigerant of 3 kg [6.6 lbs] equivalent to 50 m [165 ft] total extended piping length is already included when the outdoor unit is shipped. Thus, if the total extended piping length is 50 m [165 ft] or less, there is no need to charge with additional refrigerant.

Calculation of Additional Refrigerant Charge

• If the total extended piping length exceeds 50 m [165 ft], calculate the required additional refrigerant charge using the procedure shown below.

• If the calculated additional refrigerant charge is a negative amount, do not charge with any refrigerant.

Additional refrigerant charge

[lbs]

Liquid pipe size Total length of ø9.52 × 0.06 kg

=+–

[3/8" × 0.041 lbs]

(m) × 0.06 (kg/m), [ft] × 0.041 [lbs/ft]

Liquid pipe size Total length of ø6.35 × 0.024 kg [1/4" × 0.016 lbs]

(m) × 0.024 (kg/m), [ft] × 0.016 [lbs/ft]

Refrigerant amount for outdoor unit

3.0 kg

[6.6 lbs]

Precautions when using the charge valve (Fig.4-8)

Do not tighten the service port too much when installing it, otherwise, the valve core could be deformed and become loose, causing a gas leak. After positioning section B in the desired direction, turn section A only and tighten it. Do not further tighten sections A and B together after tightening section A.

<Example> (Please see the lower half of Fig. 4-1.) Outdoor model : P48 Indoor 1: P24 A: ø9.52 [3/8"] 30 m [98 ft] a: ø9.52 [3/8"] 15 m [49 ft] 2: P15 b: ø6.35 [1/4"] 10 m [33 ft] 3: P08 c: ø6.35 [1/4"] 10 m [33 ft] 4: P06 d: ø6.35 [1/4"] 20 m [66 ft] The total length of each liquid line is as follows

ø9.52 [3/8"] : A + a = 30 m + 15 m = 45 m [98 ft + 49 ft = 147 ft] ø6.35 [1/4"] : b + c + d = 10 m + 10 m + 20 m = 40 m [33 ft + 33 ft + 66 ft = 132 ft]

Therefore, <Calculation example> Additional refrigerant charge = 45 m × 0.06 kg + 40 m × 0.024 kg – 3.0 kg = 0.7 kg (rounded up)

= [147 ft × 0.041 lbs + 132 ft × 0.016 lbs – 6.6 lbs = 1.54 lbs]

At the conditions below:

5. Drainage piping work

Outdoor unit drainage pipe connection

When drain piping is necessary, use the drain socket or the drain pan (option).

P36·P48 Drain socket PAC-SG61DS-E Drain pan PAC-SG64DP-E

6. Electrical work

6.1. Caution

1 Follow ordinance of your governmental organization for technical standard re-

lated to electrical equipment, wiring regulations and guidance of each electric power company.

2 Wiring for control (hereinafter referred to as transmission line) shall be (5 cm [2

inch] or more) apart from power source wiring so that it is not influenced by electric noise from power source wiring. (Do not insert transmission line and power source wire in the same conduit.)

3 Be sure to provide designated grounding work to outdoor unit. 4 Give some allowance to wiring for electrical part box of indoor and outdoor units,

because the box is sometimes removed at the time of service work.

5 Never connect the main power source to terminal block of transmission line. If

connected, electrical parts will be burnt out.

6 Use 2-core shield cable for transmission line. If transmission lines of different

systems are wired with the same multiplecore cable, the resultant poor transmitting and receiving will cause erroneous operations.

7 Only the transmission line specified should be connected to the terminal block for

outdoor unit transmission. (T ransmission line to be connected with indoor unit : Terminal block TB3 f or transmission line, Other : Terminal block TB7 for centralized control) Erroneous connection does not allow the system to operate.

8 In case to connect with the upper class controller or to conduct group operation in

different refrigerant systems, the control line for transmission is required betw een the outdoor units each other. Connect this control line between the terminal blocks for centralized control. (2wire line with no polarity) When conducting group operation in different refrigerant systems without connecting to the upper class controller, replace the insertion of the short circuit connector from CN41 of one outdoor unit to CN40.

9 Group is set by operating the remote controller.

6. Electrical work

M1SM2

M1SM2L1L2GR

TB3 TB7

CONDUIT PLATE : accessory

A : Power source B : Transmission line

Fig. 6-1

6.3. Wiring transmission cables

1 Types of control cables

1. Wiring transmission cables

• Types of transmission cables: Shielding wire CVVS or CPEVS

• Cable diameter: More than 1.25 mm

• Maximum wiring length: Within 200 m [656 ft]

2. M-NET Remote control cables Kind of remote control cable

Cable diameter

Remarks

[AWG16]

Shielding wire MVVS

0.5 to 1.25 mm When 10 m [32 ft] is exceeded, use cable with the same specifications as transmission line wiring

[AWG20 to AWG16]

6.2. Control box and connecting position of wiring (Fig. 6-1)

1. Connect the indoor unit transmission line to transmission terminal block (TB3), or

connect the wiring between outdoor units or the wiring with the centralized control system to the centralized control terminal block (TB7). When using shielded wiring, connect shield ground of the indoor unit transmis-

sion line to the earth screw ( outdoor units and the central control system transmission line to the shield (S)

terminal of the centralized control terminal block (TB7) shield (S) terminal. In addition, in the case of outdoor units whose power supply connector CN41 has been replaced by CN40, the shield terminal (S) of terminal block (TB7) of the

centralized control system should also be connected to the ground (

2. Conduit mounting plates (ø27 [1-1/16 inch]) are being provided. Pass the power

supply and transmission wires through the appropriate knock-out holes, then remove the knock-out piece from the bottom of the terminal box and connect the wires.

3. Fix power source wiring to terminal box by using buffer bushing for tensile force

(PG connection or the like).

3. MA Remote control cables

Kind of remote control cable

Cable diameter

2 Wiring examples

• Controller name, symbol and allowable number of controllers.

Name Outdoor unit controller Indoor unit controller

Remote controller

) and connect shield ground of the line between

2-core cable (unshielded)

(AWG22) to 1.25 mm2 (AWG16)

0.3 mm

Symbol

(M-NET)

Allowable number of controllers

One to eight controllers for one OC Maximum of 16 controllers for one OC Maximum of two per group

Example of a group operation system with multiple outdoor units (Shielding wires and address setting are necessary.)

■ M-NET Remote Controller (Fig. 6-2)

■ MA Remote Controller (Fig. 6-3)

<Wiring Method and Address Settings> a. Always use shielded wire when making connections between the outdoor unit (OC) and the indoor unit (IC), as well for all OC-OC, and IC-IC wiring intervals. b. Use feed wiring to connect terminals M1 and M2 and the ground terminal on the transmission cable terminal block (TB3) of each outdoor unit (OC) to terminals M1, M2

and terminal S on the transmission cable block of the indoor unit (IC).

c. Connect terminals 1 (M1) and 2 (M2) on the transmission cable terminal block of the indoor unit (IC) that has the most recent address within the same group to the

terminal block on the remote controller (RC). d. Connect together terminals M1, M2 and terminal S on the terminal block for central control (TB7) for the outdoor unit (OC). e. The jumper connector CN41 on the control panel does not change.

f. Connect the terminal S on the terminal block for central control for the power supply unit to the ground terminal ( g. Set the address setting switch as follows.

Unit Range Setting Method

IC (Main) 01 to 50 Use the most recent address within the same group of indoor units

IC (Sub) 01 to 50

Outdoor Unit 51 to 100

M-NET R/C (Main) 101 to 150 Set at an IC (Main) address within the same group plus 100

M-NET R/C (Sub) 151 to 200 Set at an IC (Main) address within the same group plus 150

MA R/C – Unnecessary address setting (Necessary main/sub setting)

h. The group setting operations among the multiple indoor units is done by the remote controller (RC) after the electrical power has been turned on. <Permissible Lengths>

1 M-NET Remote controller

• Max length via outdoor units: L

• Max transmission cable length: L

• Remote controller cable length: r

2 MA Remote controller

• Max length via outdoor unit (M-NET cable): L

• Max transmission cable length (M-NET cable): L

• Remote controller cable length:c

1+L2+L3+L4 and L1+L2+L3+L5 and L1+L2+L6+L7

1 and L3+L4 and L3+L5 and L6 and L2+L6 and L7

1, r2, r2 +r3,r4

If the length exceeds 10 m [33 ft], use a 1.25 mm calculation of the maximum length and overall length.

1 and c1+c2 +c3 and c1+c2+c3+c4

Use an address, other than that of the IC (Main) from among the units within the same group of indoor units. This must be in sequence with the IC (Main) Use the most recent address of all the indoor units plus 50 * The address automatically becomes “100” if it is set as “01 - 50”.

500 m [1640 ft] (1.25 mm2 [AWG16] or more)

10 m [33 ft] (0.5 to 1.25 mm2 [AWG20 to AWG16])

1+L2+L3+L4 and L1+L2+L6+L7

1 and L3+L4 and L6 and L2+L6 and L7

200 m [656 ft] (1.25 mm2 [AWG16] or more)

[AWG16] shielded wire. The length of this section (L8) should be included in the

500 m [1640 ft] (1.25 mm2 [AWG16] or more)

200 m [656 ft] (0.3 to 1.25 mm2 [AWG20 to AWG16])

200 m [656 ft] (1.25 mm2 [AWG16] or more)

) in the electrical component box.

6. Electrical work

~/N 208/230 V

D D

~/N 208/230 V

M1M2S

M1 M2 S

TB7

TB3

(51)

M1 M2 S

TB5

(01)

M1 M2 S

TB5

(03)

M1 M2 S

TB5

(02)

M1 M2 S

TB5

(04)

M1 M2 S

TB5

(05)

M1 M2 S

TB5

(07)

M1 M2 S

TB5

(06)

(101)

(105)

(104)

(155)

M1 M2 S

TB7

(53)

M1M2S

Power Supply

Unit

M1M2S

G-50A

L6L7

AB AB AB

M1M2 S

TB3

M1 M2 S

TB7

(51)

M1 M2 1 2S

TB5 TB15

TB15

(01)

M1 M2 S

TB5

(03)

M1 M2 S

TB5

(02)

M1 M2 S

TB5

(04)

M1 M2 S

TB5

(05)

M1 M2 S

TB5

(07)

M1 M2 S

TB5

(06)

MAMAMA

M1 M2 S

TB7

(53)

Power Supply

Unit

G-50A

L6L7

ABABAB

M1M2

c2 c2

M1M2S

TB3

M1M2S

TB3

■ M-NET Remote Controller

A : Group 1 B : Group 3 C : Group 5 D : Shielded Wire E : Sub Remote Controller

( ): Address

■ MA Remote Controller

Fig. 6-2 Fig. 6-3

6.4. Wiring of main power supply and equipment capacity

Schematic Drawing of Wiring (Example) (Fig. 6-4)

A : Switch (Breakers for Wiring and Current Leakage) B : Outdoor Unit C : Pull Box D : Indoor Unit

Fig. 6-4

Thickness of Wire for Main Power Supply and On/Off Capacities

Minimum

circuit

ampacity

26 A

Model

Outdoor Unit

Indoor Unit

P36, P48

Power Supply

~/N (single), 60 Hz, 208/230 V ~/N (single), 60 Hz, 208/230 V

Minimum Wire Thickness

Main Cable*2

(mm

[AWG])

Ground

5.3 [AWG10]5.3 [AWG10]

Breaker for

Wiring*1

Refer to installation manual of indoor unit.

Breaker for Current

Leakage

30 A 30 mA 0.1 sec. or less30 A

*1. A breaker with at least 3.0 mm [1/8 inch] contact separation in each poles shall be provided. Use non-fuse breaker (NF) or earth leakage breaker (NV).

*2. Use copper supply wires. Use the electric wires over the rating voltage 300 V.

1. Use a separate power supply for the outdoor unit and indoor unit.

2. Bear in mind ambient conditions (ambient temperature,direct sunlight, rain water,etc.) when proceeding with the wiring and connections.

3. The wire size is the minimum value for metal conduit wiring. The power cord size should be 1 rank thicker consideration of voltage drops. Make sure the power-supply voltage does not drop more than 10%.

4. Specific wiring requirements should adhere to the wiring regulations of the region.

5. Power supply cords of parts of appliances for outdoor use shall not be lighter than polychloroprene sheathed flexible cord (design 60245 IEC57). For example, use wiring such as YZW.

6. Install an earth longer than other cables.

Warning:

• Be sure to use specified wires to connect so that no external force is imparted to terminal connections. If connections are not fixed firmly, it may cause heating or fire.

• Be sure to use the appropriate type of overcurrent protection switch. Note that generated overcurrent may include some amount of direct current.

Caution:

• Some installation site may require attachment of an earth leakage breaker. If no earth leakage breaker is installed, it may cause an electric shock.

• Do not use anything other than breaker and fuse with correct capacity. Using fuse and wire or copper wire with too large capacity may cause a malfunction

of unit or fire.

Maximum rating

of over current

protector device

40 A

+ 22 hidden pages

Mitsubishi Electronics R410A User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual