Mitsubishi PQHY-P500YLM-A, PQHY-P250YLM-A, PQHY-P550YLM-A, PQHY-P600YLM-A, PQHY-P400YSLM-A Service Handbook

ii

HWE15060 GB

Safety Precautions

Before installing the unit, thoroughly read the following safety precautions.
Observe these safety precautions for your safety.

WARNING

This symbol is intended to alert the user to the presence of important instructions that must be followed to avoid

the risk of serious injury or death.

CAUTION

This symbol is intended to alert the user to the presence of important instructions that must be followed to avoid

the risk of serious injury or damage to the unit.

After reading this manual, give it to the user to retain for future reference.
Keep this manual for easy reference. When the unit is moved or repaired, give this manual to those who provide these

services.
When the user changes, make sure that the new user receives this manual.

WARNING

Ask your dealer or a qualified technician to install the
unit.

Improper installation by the user may result in water leak­age, electric shock, smoke, and/or fire.

Properly install the unit on a surface that can with­stand the weight of the unit.

Unit installed on an unstable surface may fall and cause in­jury.

Only use specified cables. Securely connect each ca­ble so that the terminals do not carry the weight of the
cable.

Improperly connected or fixed cables may produce heat
and start a fire.

Take appropriate safety measures against strong
winds and earthquakes to prevent the unit from falling.

If the unit is not installed properly, the unit may fall and
cause serious injury to the person or damage to the unit.

Do not make any modifications or alterations to the
unit. Consult your dealer for repair.

Improper repair may result in water leakage, electric shock,
smoke, and/or fire.

Do not touch the heat exchanger fins.

The fins are sharp and dangerous.

In the event of a refrigerant leak, thoroughly ventilate
the room.

If refrigerant gas leaks and comes in contact with an open
flame, poisonous gases will be produced.

When installing the All-Fresh type units, take it into
consideration that the outside air may be discharged
directly into the room when the thermo is turned off.

Direct exposure to outdoor air may have an adverse effect
on health. It may also result in food spoilage.

Properly install the unit according to the instructions
in the installation manual.

Improper installation may result in water leakage, electric
shock, smoke, and/or fire.

Have all electrical work performed by an authorized
electrician according to the local regulations and in­structions in this manual, and a dedicated circuit must
be used.

Insufficient capacity of the power supply circuit or improper
installation may result in malfunctions of the unit, electric
shock, smoke, and/or fire.

ii

HWE15060 GB

WARNING

Securely attach the terminal block cover (panel) to the
unit.

If the terminal block cover (panel) is not installed properly,
dust and/or water may infiltrate and pose a risk of electric
shock, smoke, and/or fire.

Only use the type of refrigerant that is indicated on the
unit when installing or reinstalling the unit.

Infiltration of any other type of refrigerant or air into the unit
may adversely affect the refrigerant cycle and may cause
the pipes to burst or explode.

When installing the unit in a small room, exercise cau­tion and take measures against leaked refrigerant
reaching the limiting concentration.

Consult your dealer with any questions regarding limiting
concentrations and for precautionary measures before in­stalling the unit. Leaked refrigerant gas exceeding the lim­iting concentration causes oxygen deficiency.

Consult your dealer or a specialist when moving or re­installing the unit.

Improper installation may result in water leakage, electric
shock, and/or fire.

After completing the service work, check for a gas
leak.

If leaked refrigerant is exposed to a heat source, such as a
fan heater, stove, or electric grill, poisonous gases may be
produced.

Do not try to defeat the safety features of the unit.

Forced operation of the pressure switch or the temperature
switch by defeating the safety features of these devices, or
the use of accessories other than the ones that are recom­mended by MITSUBISHI may result in smoke, fire, and/or
explosion.

Only use accessories recommended by MITSUBISHI.

Ask a qualified technician to install the unit. Improper instal­lation by the user may result in water leakage, electric
shock, smoke, and/or fire.

Control box houses high-voltage parts.

When opening or closing the front panel of the control box,
do not let it come into contact with any of the internal com­ponents. Before inspecting the inside of the control box,
turn off the power, keep the unit off for at least 10 minutes,
and confirm that the voltage between FT-P and FT-N on
INV Board has dropped to DC20V or less. (It takes about
10 minutes to discharge electricity after the power supply is
turned off.)

iiiiii

HWE15060 GB

Precautions for handling units for use with R410A

CAUTION

Do not use the existing refrigerant piping.

A large amount of chlorine that is contained in the residual

refrigerant and refrigerator oil in the existing piping may
cause the refrigerator oil in the new unit to deteriorate.

R410A is a high-pressure refrigerant and can cause the

existing pipes to burst.

Use refrigerant pipes made of phosphorus deoxidized
copper. Keep the inner and outer surfaces of the pipes
clean and free of such contaminants as sulfur, oxides,
dust, dirt, shaving particles, oil, and water.

These types of contaminants inside the refrigerant pipes
may cause the refrigerant oil to deteriorate.

Store the pipes to be installed indoors, and keep both
ends of the pipes sealed until immediately before braz­ing. (Keep elbows and other joints wrapped in plastic.)

Infiltration of dust, dirt, or water into the refrigerant system
may cause the refrigerating machine oil to deteriorate or
cause the unit to malfunction.

Use a small amount of ester oil, ether oil, or alkylben­zene to coat flares and flanges.

Infiltration of a large amount of mineral oil may cause the re­frigerating machine oil to deteriorate.

Charge liquid refrigerant (as opposed to gaseous re­frigerant) into the system.

If gaseous refrigerant is charged into the system, the com­position of the refrigerant in the cylinder will change and
may result in performance loss.

Use a vacuum pump with a reverse-flow check valve.

If a vacuum pump that is not equipped with a reverse-flow
check valve is used, the vacuum pump oil may flow into the
refrigerant cycle and cause the refrigerating machine oil to
deteriorate.

Prepare tools for exclusive use with R410A. Do not use
the following tools if they have been used with the con­ventional refrigerant (gauge manifold, charging hose,
gas leak detector, reverse-flow check valve, refrigerant
charge base, vacuum gauge, and refrigerant recovery
equipment.).

If the refrigerant or the refrigerating machine oil left on

these tools are mixed in with R410A, it may cause the re­frigerating machine oil to deteriorate.

Infiltration of water may cause the refrigerating machine

oil to deteriorate.

Gas leak detectors for conventional refrigerants will not

detect an R410A leak because R410A is free of chlorine.

Do not use a charging cylinder.

If a charging cylinder is used, the composition of the refrig­erant will change, and the unit may experience power loss.

Exercise special care when handling the tools for use
with R410A.

Infiltration of dust, dirt, or water into the refrigerant system
may cause the refrigerating machine oil to deteriorate.

Only use refrigerant R410A.

The use of other types of refrigerant that contain chlorine
(i.e. R22) may cause the refrigerating machine oil to deteri­orate.

iv

HWE15060 GB

Before installing the unit

WARNING

Do not install the unit where a gas leak may occur.

If gaseous refrigerant leaks and piles up around the unit, it
may be ignited.

Do not use the unit to keep food items, animals, plants,
artifacts, or for other special purposes.

The unit is not designed to preserve food products.

Do not use the unit in an unusual environment.

Do not install the unit where a large amount of oil or steam

is present or where acidic or alkaline solutions or chemical
sprays are used frequently. Doing so may lead to a re­markable drop in performance, electric shock, malfunc­tions, smoke, and/or fire.

The presence of organic solvents or corrosive gas (i.e.

ammonia, sulfur compounds, and acid) may cause gas
leakage or water leakage.

When installing the unit in a hospital, take appropriate
measures to reduce noise interference.

High-frequency medical equipment may interfere with the
normal operation of the air conditioner or vice versa.

Do not install the unit on or over things that cannot get
wet.

When the humidity level exceeds 80% or if the drainage
system is clogged, the indoor unit may drip water. Drain wa­ter is also discharged from the heat source unit. Install a
centralized drainage system if necessary.

vv

HWE15060 GB

Before installing the unit (moving and reinstalling the unit) and performing
electrical work

CAUTION

Properly ground the unit.

Do not connect the grounding wire to a gas pipe, water pipe,
lightning rod, or grounding wire from a telephone pole. Im­proper grounding may result in electric shock, smoke, fire,
and/or malfunction due to noise interference.

Do not put tension on the power supply wires.

If tension is put on the wires, they may break and result in
excessive heat, smoke, and/or fire.

Install an earth leakage breaker to avoid the risk of
electric shock.

Failure to install an earth leakage breaker may result in
electric shock, smoke, and/or fire.

Use the kind of power supply wires that are specified
in the installation manual.

The use of wrong kind of power supply wires may result in
current leak, electric shock, and/or fire.

Use breakers and fuses (current breaker, remote
switch <switch + Type-B fuse>, moulded case circuit
breaker) with the proper current capacity.

The use of wrong capacity fuses, steel wires, or copper
wires may result in malfunctions, smoke, and/or fire.

Do not spray water on the air conditioner or immerse
the air conditioner in water.

Otherwise, electric shock and/or fire may result.

When handling units, always wear protective gloves to
protect your hands from metal parts and high-tempera­ture parts.

Periodically check the installation base for damage.

If the unit is left on a damaged platform, it may fall and
cause injury.

Properly install the drain pipes according to the in­structions in the installation manual. Keep them insu­lated to avoid dew condensation.

Improper plumbing work may result in water leakage and
damage to the furnishings.

Exercise caution when transporting products.

Products weighing more than 20 kg should not be carried

alone.

Do not carry the product by the PP bands that are used on

some products.

Do not touch the heat exchanger fins. They are sharp and

dangerous.

When lifting the unit with a crane, secure all four corners

to prevent the unit from falling.

Properly dispose of the packing materials.

Nails and wood pieces in the package may pose a risk of

injury.

Plastic bags may pose a risk of choking hazard to chil-

dren. Tear plastic bags into pieces before disposing of
them.

vi

HWE15060 GB

Before the test run

CAUTION

Turn on the unit at least 12 hours before the test run.

Keep the unit turned on throughout the season. If the unit is
turned off in the middle of a season, it may result in malfunc­tions.

To avoid the risk of electric shock or malfunction of the
unit, do not operate switches with wet hands.

Do not touch the refrigerant pipes with bare hands dur­ing and immediately after operation.

During or immediately after operation, certain parts of the
unit such as pipes and compressor may be either very cold
or hot, depending on the state of the refrigerant in the unit
at the time. To reduce the risk of frost bites and burns, do
not touch these parts with bare hands.

Do not operate the unit without panels and safety
guards.

Rotating, high-temperature, or high-voltage parts on the unit
pose a risk of burns and/or electric shock.

Do not turn off the power immediately after stopping
the operation.

Keep the unit on for at least five minutes before turning off
the power to prevent water leakage or malfunction.

Do not operate the unit without the air filter.

Dust particles may build up in the system and cause mal­functions.

CONTENTS

HWE15060 GB

I Read Before Servicing

[1] Read Before Servicing.............................................................................................................. 3

[2] Necessary Tools and Materials ................................................................................................ 4

[3] Piping Materials ........................................................................................................................ 5

[4] Storage of Piping ...................................................................................................................... 7

[5] Pipe Processing........................................................................................................................ 7

[6] Brazing...................................................................................................................................... 8

[7] Air Tightness Test..................................................................................................................... 9

[8] Vacuum Drying (Evacuation) ..................................................................................................10

[9] Refrigerant Charging .............................................................................................................. 12

[10] Remedies to be taken in case of a Refrigerant Leak............................................................ 12

[11] Characteristics of the Conventional and the New Refrigerants ............................................ 13

[12] Notes on Refrigerating Machine Oil...................................................................................... 14

[13] Precautions for servicing ...................................................................................................... 15

II Restrictions

[1] System configuration .............................................................................................................. 19

[2] Types and Maximum allowable Length of Cables .................................................................. 21

[3] Switch Settings and Address Settings .................................................................................... 23

[4] Sample System Connection ................................................................................................... 29

[5] An Example of a System to which an MA Remote Controller is connected ........................... 30

[6] An Example of a System to which an ME Remote Controller is connected ........................... 52

[7] An Example of a System to which both MA Remote Controller and

ME Remote Controller are connected .................................................................................... 56

[8] Restrictions on Pipe Length.................................................................................................... 61

III Heat source Unit Components

[1] Heat source Unit Components and Refrigerant Circuit........................................................... 81

[2] Control Box of the Heat source Unit ....................................................................................... 89

[3] Heat source Unit Circuit Board ............................................................................................... 91

[4] BC Controller Components..................................................................................................... 96

[5] Control Box of the BC Controller ............................................................................................99

[6] BC Controller Circuit Board .................................................................................................. 100

IV Remote Controller

[1] Functions and Specifications of MA and ME Remote Controllers ........................................ 105

[2] Group Settings and Interlock Settings via the ME Remote Controller .................................. 106

[3] Interlock Settings via the MA Remote Controller .................................................................. 110

[4] Using the built-in Temperature Sensor on the Remote Controller........................................ 116

V Electrical Wiring Diagram

[1] Electrical Wiring Diagram of the Heat source Unit................................................................ 119

[2] Electrical Wiring Diagram of the BC Controller..................................................................... 120

[3] Electrical Wiring Diagram of Transmission Booster.............................................................. 130

VI Refrigerant Circuit

[1] Refrigerant Circuit Diagram .................................................................................................. 133

[2] Principal Parts and Functions ............................................................................................... 139

VII Control

[1] Functions and Factory Settings of the Dipswitches .............................................................. 151

[2] Controlling the Heat source Unit........................................................................................... 157

[3] Controlling BC Controller ...................................................................................................... 174

[4] Operation Flow Chart............................................................................................................ 175

VIII Test Run Mode

[1] Items to be checked before a Test Run................................................................................ 189

[2] Test Run Method .................................................................................................................. 190

[3] Operating Characteristic and Refrigerant Amount................................................................ 193

[4] Adjusting the Refrigerant Amount......................................................................................... 193

[5] Refrigerant Amount Adjust Mode.......................................................................................... 199

[6] The following symptoms are normal. .................................................................................... 203

[7] Standard Operation Data (Reference Data) ......................................................................... 204

IX Troubleshooting

[1] Error Code Lists.................................................................................................................... 267

[2] Responding to Error Display on the Remote Controller........................................................ 271

[3] Investigation of Transmission Wave Shape/Noise ............................................................... 345

[4] Troubleshooting Principal Parts ............................................................................................ 348

[5] Refrigerant Leak ................................................................................................................... 380

CONTENTS

HWE15060 GB

[6] Compressor Replacement Instructions................................................................................. 384

[7] Water-cooled heat exchanger Replacement Instructions ..................................................... 387

[8] Servicing the BC controller ................................................................................................... 399

[9] Troubleshooting Using the Heat source Unit LED Error Display .......................................... 402

X LED Monitor Display on the Heat source Unit Board

[1] How to Read the LED on the Service Monitor ...................................................................... 405

- 1 -

HWE15060 GB

I Read Before Servicing

[1] Read Before Servicing ....................................................................................................... 3

[2] Necessary Tools and Materials.......................................................................................... 4

[3] Piping Materials ................................................................................................................. 5

[4] Storage of Piping ............................................................................................................... 7

[5] Pipe Processing................................................................................................................. 7

[6] Brazing............................................................................................................................... 8

[7] Air Tightness Test..............................................................................................................9

[8] Vacuum Drying (Evacuation) ........................................................................................... 10

[9] Refrigerant Charging........................................................................................................ 12

[10] Remedies to be taken in case of a Refrigerant Leak .......................................................12

[11] Characteristics of the Conventional and the New Refrigerants ....................................... 13

[12] Notes on Refrigerating Machine Oil ................................................................................. 14

[13] Precautions for servicing..................................................................................................15

- 2 -

HWE15060 GB

[ I Read Before Servicing ]

- 3 -

HWE15060 GB

I Read Before Servicing

[1] Read Before Servicing

1. Check the type of refrigerant used in the system to be serviced.
Refrigerant Type

Multi air conditioner for building application CITY MULTI WY/WR2 YLM-A series: R410A

2. Check the symptoms exhibited by the unit to be serviced.

Refer to this service handbook for symptoms relating to the refrigerant cycle.

3. Thoroughly read the safety precautions at the beginning of this manual.

4. Preparing necessary tools: Prepare a set of tools to be used exclusively with each type of refrigerant.

Refer to "Necessary Tools and Materials" for information on the use of tools.(page 4)

5. Verification of the connecting pipes: Verify the type of refrigerant used for the unit to be moved or replaced.

Use refrigerant pipes made of phosphorus deoxidized copper. Keep the inner and outer surfaces of the pipes clean and free

of such contaminants as sulfur, oxides, dust, dirt, shaving particles, oil, and water.

These types of contaminants inside the refrigerant pipes may cause the refrigerant oil to deteriorate.

6. If there is a leak of gaseous refrigerant and the remaining refrigerant is exposed to an open flame, a poisonous gas
hydrofluoric acid may form. Keep workplace well ventilated.

CAUTION

Install new pipes immediately after removing old ones to keep moisture out of the refrigerant circuit.
The use of refrigerant that contains chloride, such as R22, will cause the refrigerating machine oil to deteriorate.

[ I Read Before Servicing ]

- 4 -

HWE15060 GB

[2] Necessary Tools and Materials

Prepare the following tools and materials necessary for installing and servicing the unit.

Tools for use with R410A (Adaptability of tools that are for use with R22 or R407C)

1. To be used exclusively with R410A (not to be used if used with R22 or R407C)

2. Tools and materials that may be used with R410A with some restrictions

3. Tools and materials that are used with R22 or R407C that may also be used with R410A

4. Tools and materials that must not be used with R410A

Tools for R410A must be handled with special care to keep moisture and dust from infiltrating the cycle.

Tools/Materials Use Notes

Gauge Manifold Evacuation and refrigerant charging Higher than 5.09MPa[738psi] on the

high-pressure side

Charging Hose Evacuation and refrigerant charging The hose diameter is larger than the

conventional model.

Refrigerant Recovery Cylinder Refrigerant recovery

Refrigerant Cylinder Refrigerant charging The refrigerant type is indicated. The

cylinder is pink.

Charging Port on the Refrigerant Cylinder Refrigerant charging The charge port diameter is larger

than that of the current port.

Flare Nut Connection of the unit with the pipes Use Type-2 Flare nuts.

Tools/Materials Use Notes

Gas Leak Detector Gas leak detection The ones for use with HFC refrigerant

may be used.

Vacuum Pump Vacuum drying May be used if a check valve adapter

is attached.

Flare Tool Flare processing Flare processing dimensions for the

piping in the system using the new re­frigerant differ from those of R22. Re­fer to I [3] Piping Materials.

Refrigerant Recovery Equipment Refrigerant recovery May be used if compatible with

R410A.

Tools/Materials Use Notes

Vacuum Pump with a Check Valve Vacuum drying

Bender Bending pipes

Torque Wrench Tightening flare nuts Only the flare processing dimensions

for pipes that have a diameter of
ø12.70 (1/2") and ø15.88 (5/8") have
been changed.

Pipe Cutter Cutting pipes

Welder and Nitrogen Cylinder Welding pipes

Refrigerant Charging Meter Refrigerant charging

Vacuum Gauge Vacuum level check

Tools/Materials Use Notes

Charging Cylinder Refrigerant charging Prohibited to use

[ I Read Before Servicing ]

- 5 -

HWE15060 GB

[3] Piping Materials

1. Copper pipe materials

The distinction between O-materials (Annealed) and 1/2H-materials (Drawn) is made based on the strength of the pipes them-

selves.

2. Types of copper pipes

3. Piping materials/Radial thickness

Use refrigerant pipes made of phosphorus deoxidized copper.
The operation pressure of the units that use R410A is higher than that of the units that use R22.
Use pipes that have at least the radial thickness specified in the chart below.
(Pipes with a radial thickness of 0.7 mm or less may not be used.)

Annealed pipes have been used for older model units when a diameter of the pipe is up to ø19.05(3/4"). For a system that

uses R410A, use pipes that are made with 1/2H-material (Drawn) when a diameter of the pipe is more than ø19.05(3/4").
(Annealed pipes may be used for pipes with a diameter of ø19.05 (3/4") and a radial thickness of 1.2 t).

The figures in the radial thickness column are based on the Japanese standards and provided only as a reference. Use pipes

that meet the local standards.

O-material (Annealed) Soft copper pipes (annealed copper pipes). They can easily be bent with hands.

1/2H-material (Drawn) Hard copper pipes (straight pipes). They are stronger than the O-material (Annealed)

at the same radial thickness.

Maximum working pressure Refrigerant type

3.45 MPa [500psi] R22, R407C etc.

4.30 MPa [624psi] R410A etc.

Pipe size (mm[in]) Radial thickness (mm) Type

ø6.35 [1/4"] 0.8t

O-material (Annealed)

ø9.52 [3/8"] 0.8t

ø12.7 [1/2"] 0.8t

ø15.88 [5/8"] 1.0t

ø19.05 [3/4"] 1.0t

1/2H-material,

H-material (Drawn)

ø22.2 [7/8"] 1.0t

ø25.4 [1"] 1.0t

ø28.58 [1-1/8"] 1.0t

ø31.75 [1-1/4"] 1.1t

ø34.93 [1-3/8"] 1.2t

ø41.28 [1-5/8"] 1.4t

Do not use the existing piping!

[ I Read Before Servicing ]

- 6 -

HWE15060 GB

4. Thickness and refrigerant type indicated on the piping materials

Ask the pipe manufacturer for the symbols indicated on the piping material for new refrigerant.

5. Flare processing (O-material (Annealed) and OL-material only)

The flare processing dimensions for the pipes that are used in the R410A system are larger than those in the R22 system.

(ø19.05 pipes should have a radial thickness of 1.2 t and be made of annealed materials.)
If a clutch-type flare tool is used to flare the pipes in the system using R410A, the length of the pipes must be between 1.0
and 1.5 mm. For margin adjustment, a copper pipe gauge is necessary.

6. Flare nut

The flare nut type has been changed to increase the strength. The size of some of the flare nuts have also been changed.

The figures in the radial thickness column are based on the Japanese standards and provided only as a reference. Use pipes
that meet the local standards.

Flare processing dimensions (mm[in])

Pipe size (mm[in])

A dimension (mm)

R410A R22, R407C

ø6.35 [1/4"] 9.1 9.0

ø9.52 [3/8"] 13.2 13.0

ø12.7 [1/2"] 16.6 16.2

ø15.88 [5/8"] 19.7 19.4

ø19.05 [3/4"] 24.0 23.3

Flare nut dimensions (mm[in])

Pipe size (mm[in])

B dimension (mm)

R410A R22, R407C

ø6.35 [1/4"] 17.0 17.0

ø9.52 [3/8"] 22.0 22.0

ø12.7 [1/2"] 26.0 24.0

ø15.88 [5/8"] 29.0 27.0

ø19.05 [3/4"] 36.0 36.0

Dimension A

Dimension B

[ I Read Before Servicing ]

- 7 -

HWE15060 GB

[4] Storage of Piping

1. Storage location

Store the pipes to be used indoors. (Warehouse at site or owner's warehouse)
If they are left outdoors, dust, dirt, or moisture may infiltrate and contaminate the pipe.

2. Sealing the pipe ends

Both ends of the pipes should be sealed until just before brazing.
Keep elbow pipes and T-joints in plastic bags.

The new refrigerator oil is 10 times as hygroscopic as the conventional refrigerating machine oil (such as Suniso) and, if not
handled with care, could easily introduce moisture into the system. Keep moisture out of the pipes, for it will cause the oil to
deteriorate and cause a compressor failure.

[5] Pipe Processing

Use a small amount of ester oil, ether oil, or alkylbenzene to coat flares and flanges.

Use a minimum amount of oil.
Use only ester oil, ether oil, and alkylbenzene.

[ I Read Before Servicing ]

- 8 -

HWE15060 GB

[6] Brazing

No changes have been made in the brazing procedures. Perform brazing with special care to keep foreign objects (such as oxide
scale, water, and dust) out of the refrigerant system.

Example: Inside the brazed connection

1. Items to be strictly observed

Do not conduct refrigerant piping work outdoors if raining.
Use non-oxidized solder.
Use a brazing material (BCuP-3) that requires no flux when brazing between copper pipes or between a copper pipe and

copper coupling.

If installed refrigerant pipes are not immediately connected to the equipment, then braze and seal both ends.

2. Reasons

The new refrigerating machine oil is 10 times as hygroscopic as the conventional oil and is more likely to cause unit failure if

water infiltrates into the system.

Flux generally contains chloride. Residual flux in the refrigerant circuit will cause sludge to form.

3. Notes

Do not use commercially available antioxidants because they may cause the pipes to corrode or refrigerating machine oil to
deteriorate.

Use of oxidized solder for brazing Use of non-oxidized solder for brazing

[ I Read Before Servicing ]

- 9 -

HWE15060 GB

[7] Air Tightness Test

No changes have been made in the detection method. Note that a refrigerant leak detector for R22 will not detect an R410A leak.

1. Items to be strictly observed

Pressurize the equipment with nitrogen up to the design pressure (4.15MPa[601psi]), and then judge the equipment's air tight-

ness, taking temperature variations into account.

Refrigerant R410A must be charged in its liquid state (vs. gaseous state).

2. Reasons

Oxygen, if used for an air tightness test, poses a risk of explosion. (Only use nitrogen to check air tightness.)
Refrigerant R410A must be charged in its liquid state. If gaseous refrigerant in the cylinder is drawn out first, the composition

of the remaining refrigerant in the cylinder will change and become unsuitable for use.

3. Notes

Procure a leak detector that is specifically designed to detect an HFC leak. A leak detector for R22 will not detect an
HFC(R410A) leak.

Halide torch R22 leakage detector

[ I Read Before Servicing ]

- 10 -

HWE15060 GB

[8] Vacuum Drying (Evacuation)

1. Vacuum pump with a reverse-flow check valve (Photo1)

To prevent the vacuum pump oil from flowing into the refrigerant circuit during power OFF or power failure, use a vacuum
pump with a reverse-flow check valve.
A reverse-flow check valve may also be added to the vacuum pump currently in use.

2. Standard of vacuum degree (Photo 2)

Use a vacuum pump that attains 0.5Torr(65Pa) or lower degree of vacuum after 5 minutes of operation, and connect it directly
to the vacuum gauge. Use a pump well-maintained with an appropriate lubricant. A poorly maintained vacuum pump may not
be able to attain the desired degree of vacuum.

3. Required precision of vacuum gauge

Use a vacuum gauge that registers a vacuum degree of 5Torr(650Pa) and measures at intervals of 1Torr(130Pa). (A recom­mended vacuum gauge is shown in Photo2.)
Do not use a commonly used gauge manifold because it cannot register a vacuum degree of 5Torr(650Pa).

4. Evacuation time

After the degree of vacuum has reached 5Torr(650Pa), evacuate for an additional 1 hour. (A thorough vacuum drying re-

moves moisture in the pipes.)

Verify that the vacuum degree has not risen by more than 1Torr(130Pa) 1hour after evacuation. A rise by less than

1Torr(130Pa) is acceptable.

If the vacuum is lost by more than 1Torr(130Pa), conduct evacuation, following the instructions in section 6. Special vacuum

drying.

5. Procedures for stopping vacuum pump

To prevent the reverse flow of vacuum pump oil, open the relief valve on the vacuum pump side, or draw in air by loosening
the charge hose, and then stop the operation.
The same procedures should be followed when stopping a vacuum pump with a reverse-flow check valve.

6. Special vacuum drying

When 5Torr(650Pa) or lower degree of vacuum cannot be attained after 3 hours of evacuation, it is likely that water has pen-

etrated the system or that there is a leak.

If water infiltrates the system, break the vacuum with nitrogen. Pressurize the system with nitrogen gas to

0.5kgf/cm

2

G(0.05MPa) and evacuate again. Repeat this cycle of pressurizing and evacuation either until the degree of vac-

uum below 5Torr(650Pa) is attained or until the pressure stops rising.

Only use nitrogen gas for vacuum breaking. (The use of oxygen may result in an explosion.)

(Photo1) 15010H (Photo2) 14010

Recommended vacuum gauge:
ROBINAIR 14010 Thermistor Vacuum Gauge

[ I Read Before Servicing ]

- 11 -

HWE15060 GB

7. Notes

To evacuate air from the entire system

Applying a vacuum through the check joints at the refrigerant service valve (BV1 and 2) is not enough to attain the
desired vacuum pressure.
Be sure to apply a vacuum through the check joints at the refrigerant service valve (BV1 and 2) and also through the
check joints on the high and low pressure sides (CJ1 and 2).

To evacuate air only from the heat source units

Apply a vacuum through the check joints on the high and low pressure sides (CJ1, and 2).

To evacuate air from the indoor units and extension pipes

Apply a vacuum through the check joints at the refrigerant service valve (BV1 and 2).

[ I Read Before Servicing ]

- 12 -

HWE15060 GB

[9] Refrigerant Charging

1. Reasons

R410A is a pseudo-azeotropic HFC blend (boiling point R32=-52°C[-62°F], R125=-49°C[-52°F]) and can almost be handled
the same way as a single refrigerant, such as R22. To be safe, however, draw out the refrigerant from the cylinder in the liquid
phase. If the refrigerant in the gaseous phase is drawn out, the composition of the remaining refrigerant will change and be­come unsuitable for use.

2. Notes

When using a cylinder with a siphon, refrigerant is charged in the liquid state without the need for turning it upside down. Check
the type of the cylinder on the label before use.

[10] Remedies to be taken in case of a Refrigerant Leak

If the refrigerant leaks out, it may be replenished. The entire refrigerant does not need to be replaced. (Charge refrigerant in the
liquid state.)
Refer to "IX [5] Refrigerant Leak."(page 380)

Cylinder with a siphon

Cylinder color R410A is pink. Refrigerant charging in the liquid state

Cylin­der

liquid

Valve Valve

liquid

Cylin­der

Cylinder without a siphon

[ I Read Before Servicing ]

- 13 -

HWE15060 GB

[11] Characteristics of the Conventional and the New Refrigerants

1. Chemical property

As with R22, the new refrigerant (R410A) is low in toxicity and chemically stable nonflammable refrigerant.
However, because the specific gravity of vapor refrigerant is greater than that of air, leaked refrigerant in a closed room will
accumulate at the bottom of the room and may cause hypoxia.
If exposed to an open flame, refrigerant will generate poisonous gases. Do not perform installation or service work in a con­fined area.

*1 When CFC11 is used as a reference
*2 When CO

2

is used as a reference

2. Refrigerant composition

R410A is a pseudo-azeotropic HFC blend and can almost be handled the same way as a single refrigerant, such as R22. To
be safe, however, draw out the refrigerant from the cylinder in the liquid phase. If the refrigerant in the gaseous phase is drawn
out, the composition of the remaining refrigerant will change and become unsuitable for use.
If the refrigerant leaks out, it may be replenished. The entire refrigerant does not need to be replaced.

3. Pressure characteristics

The pressure in the system using R410A is 1.6 times as great as that in the system using R22.

New Refrigerant (HFC type) Conventional Refriger-

ant (HCFC type)

R410A R407C R22

R32/R125 R32/R125/R134a R22

Composition (wt%) (50/50) (23/25/52) (100)

Type of Refrigerant Pseudo-azeotropic

Refrigerant

Non-azeotropic

Refrigerant

Single Refrigerant

Chloride Not included Not included Included

Safety Class A1/A1 A1/A1 A1

Molecular Weight 72.6 86.2 86.5

Boiling Point (°C/°F) -51.4/-60.5 -43.6/-46.4 -40.8/-41.4

Steam Pressure
(25°C,MPa/77°F,psi) (gauge)

1.557/226 0.9177/133 0.94/136

Saturated Steam Density
(25°C,kg/m3/77°F,psi)

64.0 42.5 44.4

Flammability Nonflammable Nonflammable Nonflammable

Ozone Depletion Coefficient (ODP)

*1

0 0 0.055

Global Warming Coefficient (GWP)

*2

2090 1774 1810

Refrigerant Charging Method Refrigerant charging in

the liquid state

Refrigerant charging in

the liquid state

Refrigerant charging in

the gaseous state

Replenishment of Refrigerant after a Refrigerant
Leak

Available Available Available

Temperature (°C/°F)

Pressure (gauge)

R410A R407C R22

MPa/psi MPa/psi MPa/psi

-20/-4 0.30/44 0.18/26 0.14/20

0/32 0.70/102 0.47/68 0.40/58

20/68 1.34/194 0.94/136 0.81/117

40/104 2.31/335 1.44/209 1.44/209

60/140 3.73/541 2.44/354 2.33/338

65/149 4.17/605 2.75/399 2.60/377

[ I Read Before Servicing ]

- 14 -

HWE15060 GB

[12] Notes on Refrigerating Machine Oil

1. Refrigerating machine oil in the HFC refrigerant system

HFC type refrigerants use a refrigerating machine oil different from that used in the R22 system.
Note that the ester oil used in the system has properties that are different from commercially available ester oil.

2. Effects of contaminants

*1

Refrigerating machine oil used in the HFC system must be handled with special care to keep contaminants out.
The table below shows the effect of contaminants in the refrigerating machine oil on the refrigeration cycle.

3. The effects of contaminants in the refrigerating machine oil on the refrigeration cycle.

Refrigerant Refrigerating machine oil

R22 Mineral oil

R407C Ester oil

R410A Ester oil

*1. Contaminants is defined as moisture, air, processing oil, dust/dirt, wrong types of refrigerant, and refrigerating machine oil.

Cause Symptoms Effects on the refrigerant cycle

Water infiltration Frozen expansion valve

and capillary tubes

Clogged expansion valve and capillary tubes
Poor cooling performance
Compressor overheat
Motor insulation failure
Burnt motor
Coppering of the orbiting scroll
Lock
Burn-in on the orbiting scroll

Hydrolysis

Sludge formation and ad­hesion
Acid generation
Oxidization
Oil degradation

Air infiltration Oxidization

Infiltration of
contaminants

Dust, dirt

Adhesion to expansion valve and capillary
tubes

Clogged expansion valve, capillary tubes, and
drier
Poor cooling performance
Compressor overheat

Infiltration of contaminants into the com­pressor

Burn-in on the orbiting scroll

Mineral oil
etc.

Sludge formation and adhesion Clogged expansion valve and capillary tubes

Poor cooling performance
Compressor overheat

Oil degradation Burn-in on the orbiting scroll

[ I Read Before Servicing ]

- 15 -

HWE15060 GB

[13] Precautions for servicing

Control boxes house high-voltage and high-temperature electrical parts.
They may still remain energized or hot after the power is turned off.
When opening or closing the front cover of the control box, keep out of contact with the internal parts.

Before inspecting the inside of the control box, turn off the power, leave the unit turned off for at least 10 minutes, and check
that the voltage of the electrolytic capacitor (inverter main circuit) has dropped to 20 VDC or less.

When the unit is turned on, the compressor will remain energized even when it is stopped to vaporize the liquid refrigerant

that accumulates in the compressor.

When replacing the internal electrical components of the control box, tighten the screws to the recommended tightening

torque as specified below.
Recommended tightening torque for the internal electrical components of the control box

*1 When replacing semiconductor modules (e.g., diode stack, IPM, INV board (with IPM)), apply heatsink silicone evenly to

the mounting surface of the semiconductor module (or the semiconductor module on the back of the circuit board). Next,
tighten the screws holding the semiconductor module to one-third of the specified torque, and then tighten the screws to
the specified torque.

*2 Deviating from the recommended tightening torque may cause damage to the unit or its parts.

Take the following steps to ensure that the screws are properly tightened.

1) Ensure that the spring washers are parallel to the terminal block.

Even if the tightening torque is observed, if the washers are not parallel to the terminal block, then the semiconductor module
is not installed properly.

2) Check the wires are securely fastened to the screw terminals.

Screw the screws straight down so as not to damage the screw threads.

Hold the two round terminals back to back to ensure that the screw will screw down straight.

After tightening the screw, mark a line through the screw head, washer, and terminals with a permanent marker.

Example

Poor contact caused by loose screws may result in overheating and fire.
Continued use of the damaged circuit board may cause overheating and fire.

Screw Recommended tightening torque (N·m)

M3 0.69

M3.5 0.95

M4 1.47

M5 2.55

M6 2.75

M8 6.20

Proper installation

Loose screws

Spring washers are parallel to
the terminal block

Daisy-chain (transmission line only)

Terminal blocks (TB1,TB3,TB7)

Mark a line.

Place the round terminals back to back.

Power wires,transmission lines

[ I Read Before Servicing ]

- 16 -

HWE15060 GB

- 17 -

HWE15060 GB

II Restrictions

[1] System configuration ....................................................................................................... 19

[2] Types and Maximum allowable Length of Cables ........................................................... 21

[3] Switch Settings and Address Settings ............................................................................. 23

[4] Sample System Connection............................................................................................. 29

[5] An Example of a System to which an MA Remote Controller is connected..................... 30

[6] An Example of a System to which an ME Remote Controller is connected..................... 52

[7] An Example of a System to which both MA Remote Controller and

ME Remote Controller are connected.............................................................................. 56

[8] Restrictions on Pipe Length ............................................................................................. 61

- 18 -

HWE15060 GB

[ II Restrictions ]

- 19 -

HWE15060 GB

II Restrictions

[1] System configuration

1. Table of compatible indoor units <PQHY>

The table below summarizes the types of indoor units that are compatible with different types of heat source units.

1) "Maximum total capacity of connectable indoor units" refers to the sum of the numeric values in the indoor unit model names.

2) If the total capacity of the indoor units that are connected to a given heat source unit exceeds the capacity of the heat source
unit, the indoor units will not be able to perform at the rated capacity when they are operated simultaneously. Select a com­bination of units so that the total capacity of the connected indoor units is at or below the capacity of the heat source unit
whenever possible.

Heat

source

units

Composing units Maximum total capacity

of connectable indoor

units

Maximum number
of connectable in-

door units

Types of connectable in-

door units

P200 - - 100 - 260 1 - 17 P15 - P250 models

R410A series indoor units

P250 - - 125 - 325 1 - 21

P300 - - 150 - 390 1 - 26

P350 - - 175 - 455 1 - 30

P400 - - 200 - 520 1 - 34

P450 - - 225 - 585 1 - 39

P500 - - 250 - 650 1 - 43

P550 - - 275 - 715 2 - 47

P600 - - 300 - 780 2 - 50

P400 P200 P200 200 - 520 1 - 34

P450 P250 P200 225 - 585 1 - 39

P500 P250 P250 250 - 650 1 - 43

P550 P300 P250 275 - 715 2 - 47

P600 P300 P300 300 - 780

2 - 50

P700 P350 P350 350 - 910

P750 P400 P350 375 - 975

P800 P400 P400 400 - 1040

P850 P450 P400 425 - 1105

P900 P450 P450 450 - 1170

[ II Restrictions ]

- 20 -

HWE15060 GB

1. Table of compatible indoor units <PQRY>

The table below summarizes the types of indoor units that are compatible with different types of heat source units.

< Hybrid City Multi system >

1) "Maximum total capacity of connectable indoor units" refers to the sum of the numeric values in the indoor unit model names.

2) If the total capacity of the indoor units that are connected to a given heat source unit exceeds the capacity of the heat source
unit, the indoor units will not be able to perform at the rated capacity when they are operated simultaneously. Select a com­bination of units so that the total capacity of the connected indoor units is at or below the capacity of the heat source unit
whenever possible.

Heat

source

units

Composing units Maximum total capacity

of connectable indoor

units

Maximum number
of connectable in-

door units

Types of connectable in-

door units

P200 - - 100 - 300 1 - 20 P15 - P250 models

R410A series indoor units

P250 - - 125 - 375 1 - 25

P300 - - 150 - 450 1 - 30

P350 - - 175 - 525 1 - 35

P400 - - 200 - 600 1 - 40

P450 - - 225 - 675 1 - 45

P500 - - 250 - 750 1 - 50

P550 - - 275 - 825

2 - 50

P600 - - 300 - 900

P400 P200 P200 200 - 600 1 - 40

P450 P250 P200 225 - 675 1 - 45

P500 P250 P250 250 - 750 1 - 50

P550 P300 P250 275 -825

2 - 50

P600 P300 P300 300 - 900

P700 P350 P350 350 - 1050

P750 P400 P350 375 - 1125

P800 P400 P400 400 - 1200

P850 P450 P400 425 - 1275

P900 P450 P450 450 - 1350

Heat source units HBC controller

Sub-HBC

Maximum total capacity

of connectable indoor

units

Maximum number

of connectable in-

door units

Types of connectable

indoor units

P200 CMB-WP108V-GA1,

CMB-WP1016V-GA1

CMB-WP108V-GB1,
CMB-WP1016V-GB1

100 - 300 50 WP15- WP50 models

Indoor units for use with
HBC controller

P250 125 - 375 50

P300 150 - 450 50

P350 175 - 525 50

P400 200 - 600 50

P450 225 - 675 50

P500 250 - 750 50

[ II Restrictions ]

- 21 -

HWE15060 GB

[2] Types and Maximum allowable Length of Cables

1. Wiring work

(1) Notes

1) Have all electrical work performed by an authorized electrician according to the local regulations and instructions in this man­ual.

2) Install external transmission cables at least 5cm [1-31/32"] away from the power supply cable to avoid noise interference.
(Do not put the control cable and power supply cable in the same conduit tube.)

3) Provide grounding for the heat source unit as required.

4) Run the cable from the electric box of the indoor or heat source unit in such way that the box is accessible for servicing.

5) Do not connect power supply wiring to the terminal block for transmission line. Doing so will damage the electronic compo­nents on the terminal block.

6) Use 2-core shielded cables as transmission cables.
Use a separate 2-core control cable for each refrigerant system. Do not use a single multiple-core cable to connect indoor

units that belong to different refrigerant systems. The use of a multiple-core cable may result in signal transmission errors and
malfunctions.

7) When extending the transmission cable, be sure to connect the shield.

8) When opening or closing the front cover of the control box, keep out of contact with the internal parts.Before inspecting the
inside of the control box, turn off the power, leave the unit turned off for at least 10 minutes, and check that the voltage of the
electrolytic capacitor (inverter main circuit) has dropped to 20 VDC or less.

9) Control boxes house high-voltage and high-temperature electrical parts. Use caution not to come in contact with them.

10) When the unit is turned on, the compressor will remain energized even when it is stopped to vaporize the liquid refrigerant

that accumulates in the compressor. Disconnect the power supply cable from the compressor terminal block, and measure
the insulation resistance of the compressor.Check that the compressor is not ground faulted.If the insulation resistance is 1
MΩ or below, reconnect power supply to the compressor, and turn on the power.

11) Read Chapter I [13] Precautions for servicing (page 15), and tighten screws to the appropriate torque.Loose screws and poor

contact can result in overheating and fire.

(2) Control wiring

Different types of control wiring are used for different systems.
Refer to section "[5] An Example of a System to which an MA Remote Controller is connected - [7] An Example of a System
to which both MA Remote Controller and ME Remote Controller are connected" before performing wiring work.

Types and maximum allowable length of cables

Control lines are categorized into 2 types: transmission line and remote controller line.
Use the appropriate type of cables and observe the maximum allowable length specified for a given system. If a given system

has a long transmission line or if a noise source is located near the unit, place the unit away from the noise source to reduce
noise interference.

TB3TB7TB3TB

7

TB3TB7TB3TB

7

TB3TB7TB3TB

7

TB3TB7TB3TB

7

TB3: Terminal block for indoor-heat source transmission line TB7: Terminal block for centralized control

multiple-core cable

BC Controller

Indoor unit

Remote Controller

Remote Controller

2-core shielded cable

2-core shielded cable

Heat source unit

BC Controller

Indoor unit

Heat source unit