Mitsubishi Electric Mr. Slim PCA-RP-GA Installation Manual

Air-Conditioners

PCA-RP·GA

INSTALLATION MANUAL

For safe and correct use, please read this installation manual thoroughly before installing the air-conditioner
unit.

INSTALLATIONSHANDBUCH

Zum sicheren und ordnungsgemäßen Gebrauch der Klimaanlage das Installationshandbuch gründlich
durchlesen.

MANUEL D’INSTALLATION

Veuillez lire le manuel d’installation en entier avant d’installer ce climatiseur pour éviter tout accident et vous
assurer d’une utilisation correcte.

INSTALLATIEHANDLEIDING

Voor een veilig en juist gebruik moet u deze installatiehandleiding grondig doorlezen voordat u de airconditioner
installeert.

MANUAL DE INSTALACIÓN

Para un uso seguro y correcto, lea detalladamente este manual de instalación antes de montar la unidad de
aire acondicionado.

MANUALE DI INSTALLAZIONE

Per un uso sicuro e corretto, leggere attentamente questo manuale di installazione prima di installare il condizionatore
d’aria.

E°XEIPI¢IO O¢H°IøN E°KATA™TA™H™

°И· ·ЫК¿ПВИ· О·И ЫˆЫЩ‹ ¯Ъ‹ЫЛ, ·Ъ·О·ПВ›ЫЩВ ‰И·‚¿ЫВЩВ ЪФЫВ¯ЩИО¿ ·˘Щfi ЩФ ВБ¯ВИЪ›‰ИФ ВБО·Щ¿ЫЩ·ЫЛ˜
ЪИУ ·Ъ¯›ЫВЩВ ЩЛУ ВБО·Щ¿ЫЩ·ЫЛ ЩЛ˜ МФУ¿‰·˜ ОПИМ·ЩИЫМФ‡.

MANUAL DE INSTALAÇÃO

Para segurança e utilização correctas, leia atentamente este manual de instalação antes de instalar a unidade
de ar condicionado.

FOR INSTALLER

FÜR INSTALLATEURE

POUR L’INSTALLATEUR

VOOR DE INSTALLATEUR

PARA EL INSTALADOR

PER L’INSTALLATORE

°π∞ ∞À∆√¡ ¶√À ∫∞¡∂π ∆∏¡ ∂°∫∞∆∞™∆∞™∏

PARA O INSTALADOR

English

Deutsch

Français

Nederlands

Español

Italiano

∂ППЛУИО¿

Português

INSTALLATIONSMANUAL

Læs venligst denne installationsmanual grundigt, før De installerer airconditionanlægget, af hensyn til sikker og
korrekt anvendelse.

INSTALLATIONSMANUAL

Läs denna installationsmanual noga för säkert och korrekt bruk innan luftkonditioneringen installeras.

MONTAJ ELK‹TABI

Emniyetli ve do¤ru biçimde nas›l kullan›laca¤›n› ö¤renmek için lütfen klima cihaz›n› monte etmeden önce bu
elkitab›n› dikkatle okuyunuz.

РУКОВОДСТВО ПО УСТАНОВКЕ

Для осторожного и правильного использования прибора необходимо тщательно ознакомиться с данным
руководством по установке до выполнения установки кондиционера.

TIL INSTALLATØREN

Dansk

FÖR INSTALLATÖREN

Svenska

MONTÖR ‹Ç‹N

Türkçe

ДЛЯ УСТАНОВИТЕЛЯ

Русский

Contents

ELV

1. Safety precautions ................................................................................... 2

2. Installation location .................................................................................. 3

3. Installing the indoor unit ........................................................................... 3

4. Installing the refrigerant piping ................................................................. 5

1. Safety precautions

s Before installing the unit, make sure you read all the “Safety precau-

tions”.

s Please report to your supply authority or obtain their consent before

connecting this equipment to the power supply system.

Warning:
Describes precautions that must be observed to prevent danger of injury or
death to the user.

Caution:
Describes precautions that must be observed to prevent damage to the unit.

After installation work has been completed, explain the “Safety Precautions,” use,
and maintenance of the unit to the customer according to the information in the Op­eration Manual and perform the test run to ensure normal operation. Both the Instal­lation Manual and Operation Manual must be given to the user for keeping. These
manuals must be passed on to subsequent users.

Warning:

• Ask a dealer or an authorized technician to install the unit.

• For installation work, follow the instructions in the Installation Manual and use

tools and pipe components specifically made for use with refrigerant specified
in the outdoor unit installation manual.

• The unit must be installed according to the instructions in order to minimize

the risk of damage from earthquakes, typhoons, or strong winds. An incor­rectly installed unit may fall down and cause damage or injuries.

• The unit must be securely installed on a structure that can sustain its weight.

• If the air conditioner is installed in a small room, measures must be taken to

prevent the refrigerant concentration in the room from exceeding the safety
limit in the event of refrigerant leakage. Should the refrigerant leak and cause
the concentration limit to be exceeded, hazards due to lack of oxygen in the
room may result.

5. Drainage piping work ............................................................................... 5

6. Electrical work .......................................................................................... 6

7. Test run .................................................................................................... 8

: Indicates an action that must be avoided.

: Indicates that important instructions must be followed.

: Indicates a part which must be grounded.

: Indicates that caution should be taken with rotating parts.

: Indicates that the main switch must be turned off before servicing.

: Beware of electric shock.

: Beware of hot surface.

: At servicing, please shut down the power supply for both the Indoor and

Outdoor Unit.

Warning:

Carefully read the labels affixed to the main unit.

• Ventilate the room if refrigerant leaks during operation. If refrigerant comes
into contact with a flame, poisonous gases will be released.

• All electric work must be performed by a qualified technician according to
local regulations and the instructions given in this manual.

• Use only specified cables for wiring.

• The terminal block cover panel of the unit must be firmly attached.

• Use only accessories authorized by Mitsubishi Electric and ask a dealer or
an authorized technician to install them.

• The user should never attempt to repair the unit or transfer it to another loca­tion.

• After installation has been completed, check for refrigerant leaks. If refriger­ant leaks into the room and comes into contact with the flame of a heater or
portable cooking range, poisonous gases will be released.

1.1. Before installation (Environment)

Caution:

• Do not use the unit in an unusual environment. If the air conditioner is in­stalled in areas exposed to steam, volatile oil (including machine oil), or sulfuric
gas, areas exposed to high salt content such as the seaside, the performance
can be significantly reduced and the internal parts can be damaged.

• Do not install the unit where combustible gases may leak, be produced, flow,
or accumulate. If combustible gas accumulates around the unit, fire or explo­sion may result.

• Do not keep food, plants, caged pets, artwork, or precision instruments in the
direct airflow of the indoor unit or too close to the unit, as these items can be
damaged by temperature changes or dripping water.

1.2. Before installation or relocation

Caution:

• Be extremely careful when transporting the units. Two or more persons are
needed to handle the unit, as it weighs 20 kg or more. Do not grasp the
packaging bands. Wear protective gloves as you can injure your hands on
the fins or other parts.

• Be sure to safely dispose of the packaging materials. Packaging materials,
such as nails and other metal or wooden parts may cause stabs or other
injuries.

1.3. Before electric work

Caution:

• Be sure to install circuit breakers. If not installed, electric shock may result.

• For the power lines, use standard cables of sufficient capacity. Otherwise, a
short circuit, overheating, or fire may result.

• When installing the power lines, do not apply tension to the cables.

1.4. Before starting the test run

Caution:

• Turn on the main power switch more than 12 hours before starting operation.
Starting operation just after turning on the power switch can severely dam­age the internal parts.

• Before starting operation, check that all panels, guards and other protective
parts are correctly installed. Rotating, hot, or high voltage parts can cause
injuries.

• When the room humidity exceeds 80% or when the drainpipe is clogged, wa­ter may drip from the indoor unit. Do not install the indoor unit where such
dripping can cause damage.

• When installing the unit in a hospital or communications office, be prepared
for noise and electronic interference. Inverters, home appliances, high-fre­quency medical equipment, and radio communications equipment can cause
the air conditioner to malfunction or breakdown. The air conditioner may also
affect medical equipment, disturbing medical care, and communications equip­ment, harming the screen display quality.

• Thermal insulation of the refrigerant pipe is necessary to prevent condensa­tion. If the refrigerant pipe is not properly insulated, condensation will be formed.

• Place thermal insulation on the pipes to prevent condensation. If the drain­pipe is installed incorrectly, water leakage and damage to the ceiling, floor,
furniture, or other possessions may result.

• Do not clean the air conditioner unit with water. Electric shock may result.

• Tighten all flare nuts to specification using a torque wrench. If tightened too
much, the flare nut can break after an extended period.

• Be sure to ground the unit. If the unit is not properly grounded, electric shock
may result.

• Use circuit breakers (ground fault interrupter, isolating switch (+B fuse), and
molded case circuit breaker) with the specified capacity. If the circuit breaker
capacity is larger than the specified capacity, breakdown or fire may result.

• Do not operate the air conditioner without the air filter set in place. If the air

filter is not installed, dust may accumulate and breakdown may result.

• Do not touch any switch with wet hands. Electric shock may result.

• Do not touch the refrigerant pipes with bare hands during operation.

• After stopping operation, be sure to wait at least five minutes before turning off

the main power switch. Otherwise, water leakage or breakdown may result.

2

2. Installation location

E

D

H

C

W

A

B

UNIT

A

C

B

680

320 80

13775

8685

11

D

E

46

F

43

A

F

H D

G

E

226

F

B

C

180

200

241

H
G

E

GH

A

B

A

C

B

125

151(211)170(230)

70

80 Ø65 Ø100

2.1. Outline dimensions (Indoor unit) (Fig. 2-1)

Select a proper position allowing the following clearances for installation and mainte­nance.

Models W D H ABCE

RP2 1000 680 221 Min. 270 Min. 300 Min. 500 Max. 250

RP2.5, 3 1310 680 221 Min. 270 Min. 300 Min. 500 Max. 250

RP4 1310 680 281 Min. 270 Min. 300 Min. 500 Max. 250

RP5, 6 1620 680 281 Min. 270 Min. 300 Min. 500 Max. 250

Warning:
Mount the indoor unit on a ceiling strong enough to withstand the weight of the
unit.

(mm)

Fig. 2-1

3. Installing the indoor unit

1

4

7

2

5

Fig. 3-1

2.2. Outline dimensions (Outdoor unit)

Refer to the outdoor unit installation manual.

3

3.1. Check the indoor unit accessories (Fig. 3-1)

The indoor unit should be supplied with the following accessories (contained in the
inside of the intake grille).

Accessory name Q’ty

6

1 Washer 4 pcs
2 Pipe cover 1 pc Large size (For gas tubing)
3 Pipe cover 1 pc Small size (For liquid tubing)
4 Band 4 pcs
5 Joint socket 1 pc Marked with “UNIT”
6 Socket cover 1 pc
7 Drain tubing cover 1 pc

3.2. Preparation for installation (Fig. 3-2)

3.2.1. Suspension bolt installing spacing

Models A B C
RP2 933 1000 221
RP2.5, 3 1240 1310 221
RP4 1240 1310 281
RP5, 6 1547 1620 281

3.2.2. Refrigerant and drain tubing location

Models D E F G H J K L
RP2, 2.5, 3 131 175 178 90 82 159 156 90
RP4, 5, 6 191 235 238 150 142 219 216 150

A Front side outlet E Right drain tubing

B Left side outlet F Left drain tubing

C Right side outlet G Gas tubing

D Independent piece (Removable) H Liquid tubing

(mm)

(mm)

Fig. 3-2

Fig. 3-3

(mm)

3.2.3. Selection of suspension bolts and tubing positions (Fig. 3-3)

Using the pattern paper provided for installation, select proper positions for suspen­sion bolts and tubing and prepare relative holes.

A Pattern paper

B Suspension bolt hole

C Indoor unit width

Secure the suspension bolts or use angle stock braces or square timbers for bolt
installation.

A Use inserts of 100 kg to 150 kg each.

B Use suspension bolts of W3/8 or M10 in size

3

3. Installing the indoor unit

B

A

C

1

a

b

10–20

C

D

A

7–12

B

E

F

G

H

C

Fig. 3-4

Fig. 3-5

Fig. 3-6

(mm)

3.2.4. Indoor unit preparation (Fig. 3-4)

1. Install the suspending bolts. (Procure the W3/8 or M10 bolts locally.)
Predetermine the length from the ceiling (1 within 100 mm).

A Ceiling surface
B Suspending bolt
C Suspending bracket

2. Remove the intake grille.
Slide the intake grille holding knobs (at two locations) backward to open the intake
grille.

3. Remove the side panel.
Remove the side panel holding screws (one in each side, right and left) then slide the
side panel forward for removal.

3.3. Installing the indoor unit

Use a proper suspending method depending on the presence or absence of ceiling
materials as follows. (Fig. 3-5)
In the absence of ceiling materials

a Suspending bracket
b Unit

1) Directly suspending the unit (Fig. 3-6)

Installing procedures

1. Install the washer 1 (supplied with the unit) and the nut (to be locally procured).

2. Set (hook) the unit through the suspending bolts.

3. Tighten the nuts.
Check the unit installing condition.

• Check that the unit is horizontal between the right and left sides.

• Check that the unit slopes continuously downward from the front to the rear.

When embedding pipes, into the wall

2) Installing the suspending bracket first onto the ceiling (Fig. 3-7)

Installing procedures

1. Remove the suspending brackets, U-shaped washers, and suspending bracket
holding screws from the unit.

2. Adjust the suspending bracket holding bolts on the unit.

3. Attach the suspending brackets to the suspending bolts.

4. Set (hook) the unit to the suspending brackets.

∗ Be sure to install the U-shaped washers.

A Bolt
B Unit
C Washer
D Suspending bracket holding screw
E Bolt
F Washer 1
G Double nuts

H RP2 900 - 905

RP2.5, 3, 4 1207 - 1212
RP5, 6

(mm)

1514 - 1519

Fig. 3-7

4

90° ±0.5°

øA

R0.4~R0.8

A

45°±2°

B

C

D

4. Installing the refrigerant piping

G

C

DE

A

B

D

E

F

C

B

A

Fig. 4-1

A Flare cutting dimensions

Copper pipe O.D. Flare dimensions

(mm) øA dimensions (mm)

ø6.35 8.7 - 9.1
ø9.52 12.8 - 13.2

ø12.7 16.2 - 16.6
ø15.88 19.3 - 19.7
ø19.05 23.6 - 24.0

4.1. Connecting pipes (Fig. 4-1)

• When commercially available copper pipes are used, wrap liquid and gas pipes
with commercially available insulation materials (heat-resistant to 100 °C or more,
thickness of 12 mm or more).

• The indoor parts of the drain pipe should be wrapped with polyethylene foam insu­lation materials (specific gravity of 0.03, thickness of 9 mm or more).

• Apply thin layer of refrigerant oil to pipe and joint seating surface before tightening
flare nut.

• Use two wrenches to tighten piping connections.

• Use refrigerant piping insulation provided to insulate indoor unit connections. Insu-

late carefully.

B Flare nut tightening torque

Copper pipe O.D. Flare nut O.D. Tightening torque

(mm) (mm) (N·m)

ø6.35 17 14 - 18
ø6.35 22 34 - 42
ø9.52 22 34 - 42
ø12.7 26 49 - 61

ø12.7 29 68 - 82
ø15.88 29 68 - 82
ø15.88 36 100 - 120
ø19.05 36 100 - 120

C Apply refrigerating machine oil over the entire flare seat surface.
D Use the flare nuts as follows.

*1: The flare nut is attached to its pipe.
*2: The flare nut is in the outdoor unit accessory.

Refer to the outdoor unit installation manual for the specification of connecting pipes.

Indoor unit RP1.6, 2 RP2.5, 3 RP4-6

Refrigerant R407C

Joint outdoor unit PU(H)-P1.6/2 PU(H)-P2.5/3 PU(H)-P4/5/6

Gas side Pipe size (mm) ø15.88 ø15.88 ø19.05

Liquid side Pipe size (mm) ø9.52 ø9.52 ø9.52

Joint outdoor unit

Gas side Pipe size (mm) ø12.7 ø15.88 ø15.88

Liquid side Pipe size (mm) ø6.35 ø9.52 ø9.52

Do not use the flare nut attached. If it is used, a gas leakage or even a pipe
extraction may occur.

Indoor nut *1 *1 *1

Outdoor nut *1 *1 *1

Indoor nut *1 *1 *1

Outdoor nut *1 *1 *1

Indoor unit RP1.6, 2 RP2.5, 3 RP4-6

Refrigerant R410A

PUHZ-RP1.6/2 PUHZ-RP2.5/3 PUHZ-RP4/5/6

Indoor nut *2 *1 *2

Outdoor nut *1 *1 *1

Indoor nut *2 *1 *1

Outdoor nut *1 *1 *1

Fig. 4-2

5. Drainage piping work

Fig. 5-1

A Drain pan
B Plug

4.2. Indoor unit (Fig. 4-2)

Installing procedures

1. Slide the supplied pipe cover 2 over the gas tubing until it is pressed against the
sheet metal inside the unit.

2. Slide the provided pipe cover 3 over the liquid tubing until it is pressed against
the sheet metal inside the unit.

3. Tighten the pipe covers 2 and 3 at the both ends (15 - 20 mm) with the supplied
bands 4.

A Gas tubing E Pipe cover 3
B Liquid tubing F Press the pipe cover against the sheet metal.
C Band 4 G Refrigerant tubing heat insulating material
D Pipe cover 2

4.3. For twin/triple combination

Refer to the outdoor unit installation manual.

5.1. Preparation for left side tubing installation (Fig. 5-1)

• For left side tubing, be sure to insert the rubber plug into the right drain port.

• Install the drain tubing as it slopes continuously downward.

• After completion of work, check that correct drain is available from the outflow port

of the drain tubing.

5

L

1

N

2

S1 S2 S3

5. Drainage piping work

3.B

1.D

2.C

4.E

B

C

D

A

E

F

1

2 3

L

1

N

2

G

K

F

J

I

H

E

D

C

B

A

A Drain pan
B Drain tubing
C Socket cover 6
D Joint socket 5
E Drain tubing cover 7

Fig. 5-2

Fig. 5-3

6. Electrical work

F Drain tubing sensor

Installing procedures (Fig. 5-2)

1. Attach the joint socket 5 supplied with the unit to the drain port on the unit with a
vinyl chloride adhesive.

2. Fasten the socket cover 6 supplied with the unit to the joint socket 5.

3. Attach the field drain tubing (VP20) to the joint socket 5 with a vinyl chloride
adhesive.

4. Wrap the drain tubing cover 7 supplied with the unit. (Seam taping)

5. Check for correct drainage. (Fig. 5-3)

∗ Fill the drain pan with water of about 1 L from the tubing sensor access port.
∗ After checking for correct drainage, replace the tubing sensor access port cover.

6-1. Electric wiring (Fig. 6-1)

Wiring procedures

1. Remove the (two) tapping screws then remove the electric part cover.

2. Connect the electric wires securely to the corresponding terminals.

3. Replace the removed parts.

4. Tie the electric wires with the local wiring clamp located in the right side of the
junction box.

A Cover
B Set screws
C Beam
D Wiring clamp
E Power supply board
F Control board
G Wire service entrance
H Terminal block for indoor and outdoor units connection
I Terminal block for electric heater power supply (for only PCH models)
J Terminal block for remote controller
K Grounding cable connector

Fig. 6-1

Indoor unit model
Indoor unit power supply (Heater)
Indoor unit input capacity (Heater)
Main switch (Breaker)

Indoor unit power supply (Heater)
Indoor unit power supply (Heater) earth

)

2

Indoor unit-Outdoor unit

(mm

Wiring

Indoor unit-Outdoor unit
Remote controller-Indoor unit *2

Wire No. × size

Indoor unit (Heater) L-N *3
Indoor unit-Outdoor unit S1-S2 *3
Indoor unit-Outdoor unit S2-S3 *3

rating

Circuit

Remote controller-Indoor unit *3

*1. A breaker with at least 3 mm contact separation in each pole shall be provided. Use non-fuse breaker (NF) or earth leakage breaker (NV).
*2. A 10 m wire is attached in the remote controller accessory.
*3. The figures are NOT always against the ground.

Notes: 1. Wiring size must comply with the applicable local and national code.

S3 terminal has DC 24 V against S2 terminal. However between S3 and S1, these terminals are not electrically insulataed by the transformer or other device.

6

2. Power supply cords and Indoor unit/Outdoor unit connecting cords shall not be lighter than polychloroprene sheathed flexible cord. (Design 245 IEC 57)

3. Install an earth longer and thicker than other cables.

earth

PCA PCH

– ~/N (single), 50Hz, 220-230-240V

*1

– 2 × Min. 1.5
– 1 × Min. 1.5

3 × 2.5 (Polar) 3 × 2.5 (Polar)

1 × Min. 2.5 1 × Min. 2.5

2 × 0.69 (Non-polar) 2 × 0.69 (Non-polar)

– AC 220-230-240V

AC 220-230-240V AC 220-230-240V

DC24V DC24V
DC14V DC14V

16A–

6. Electrical work

30

46

30

30120

83.5

A

B

C

F

A

H

C

D

E

G

I

I

I

H

B

J

H

A

AB TB6

B

1

234

ON

1

234

ON

C

ON/OFF

CENTRALLY CONTROLLED

ERROR CODE

CLOCK

ON OFF

˚C

CHECK

CHECK MODE

FILTER

TEST RUN
FUNCTION

˚C

1Hr.

NOT AVAILABLE

STAND BY
DEFROST

FILTER

CHECK TEST

TEMP.

TIMER SET

F
G
E

CD

B

A

4321

STAND BY
DEFROST

INDOOR UNIT
ADDRESS NO

CLOCK

ON OFF

˚C

1Hr.

˚C

CHECK MODE

FILTER

CLOCK

FUNCTION

4

1

STAND BY
DEFROST

INDOOR UNIT
ADDRESS NO

CLOCK

ON OFF

˚C

1Hr.

˚C

CHECK MODE

FILTER

CLOCK

FUNCTION

STAND BY
DEFROST

INDOOR UNIT
ADDRESS NO

CLOCK

ON OFF

˚C

1Hr.

˚C

CHECK MODE

FILTER

CLOCK

FUNCTION

STAND BY
DEFROST

INDOOR UNIT
ADDRESS NO

CLOCK

ON OFF

˚C

1Hr.

˚C

CHECK MODE

FILTER

CLOCK

FUNCTION

21

Fig. 6-2

B-1. B-2.

Fig. 6-3

Fig. 6-4

6.2. Remote controller

6.2.1. For wired remote controller

1) Installing procedures

(1) Select an installing position for the remote controller. (Fig. 6-2)
The temperature sensors are located on both remote controller and indoor unit.

s Procure the following parts locally:

Two piece switch box
Thin copper conduit tube
Lock nuts and bushings

A Remote controller profile
B Required clearances surrounding the remote controller
C Installation pitch

(2) Seal the service entrance for the remote controller cord with putty to prevent pos-

sible invasion of dew drops, water, cockroaches or worms. (Fig. 6-3)

A For installation in the switch box:
B For direct installation on the wall select one of the following:

• Prepare a hole through the wall to pass the remote controller cord (in order to run
the remote controller cord from the back), then seal the hole with putty.

• Run the remote controller cord through the cut-out upper case, then seal the cut­out notch with putty similarly as above.

B-1. To lead the remote controller cord from the back of the controller:
B-2. To run the remote controller cord through the upper portion:

(3) For direct installation on the wall

C Wall
D Conduit
E Lock nut
F Bushing
G Switch box
H Remote controller cord
I Seal with putty
J Wood screw

2) Connecting procedures (Fig. 6-4)

1 Connect the remote controller cord to the terminal block.

A To TB5 on the indoor unit
B TB6 (No polarity)

2 Set the dip switch No.1 shown below when using two remote controller’s for the

same group.

C Dip switches

Setting the dip switches

The dip switches are at the bottom of the remote controller. Remote controller Main/
Sub and other function settings are performed using these switches. Ordinarily, only
change the Main/Sub setting of SW No.1. (The factory settings are all “ON”.)

<SW No. 1>

SW contents Main Remote controller Main/Sub setting

ON/OFF

Main/Sub

Comment Set one of the two remote controllers at one group to “Main”

<SW No. 2>

SW contents Main When remote controller power turned on

ON/OFF

Comment

Normally on/Timer mode on
When you want to return to the timer mode when the power is restored
after a power failure when a Program timer is connected, select “Timer
mode”.

Fig. 6-5

1

⁄ Mode number

2

⁄ Setting number

3

⁄ Refrigerant address

4

⁄ Unit number

<SW No. 3>

SW contents Main Cooling/heating display in AUTO mode

ON/OFF

Comment

Yes/No
When you do not want to display “Cooling” and “Heating” in the Auto
mode, set to “No”.

<SW No. 4>

SW contents Main Intake temperature display

ON/OFF

Yes/No

Comment When you do not want to display the intake temperature, set to “No”.

6.3. Function settings

6.3.1. For wired remote controller (Fig. 6-5)

Changing the power voltage setting

• Be sure to change the power voltage setting depending on the voltage used.

1 Go to the function setting mode.

Switch OFF the remote controller.
Press the A and B buttons simultaneously and hold them for at least 2
seconds. FUNCTION will start to flash.

2 Use the C button to set the refrigerant address (3) to 00.
3 Press D and [--] will start to flash in the unit number (4) display.
4 Use the C button to set the unit number (4) to 00.
5 Press the E MODE button to designate the refrigerant address/unit number. [--]

will flash in the mode number (1) display momentarily.

6 Press the F buttons to set the mode number (1) to 04.
7 Press the G button and the current set setting number (2) will flash.

Use the F button to switch the setting number in response to the power supply
voltage to be used.
Power supply voltage

8 Press the MODE button E and mode and the setting number (1) and (2) will

change to being on constantly and the contents of the setting can be confirmed.

9 Press the FILTER A and TEST RUN B buttons simultaneously for at least two

seconds. The function selection screen will disappear momentarily and the air
conditioner OFF display will appear.

240 V : Setting number = 1
220 V, 230 V : Setting number = 2

7

6. Electrical work

ON/OFF

CENTRALLY CONTROLLED

ERROR CODE

CLOCK

ON OFF

˚C

CHECK

CHECK MODE

FILTER

TEST RUN
FUNCTION

˚C

1Hr.

NOT AVAILABLE

STAND BY
DEFROST

FILTER

CHECK TEST

TEMP.

TIMER SET

DEF

HIJKLMG

CB A

ON/OFF

CHECK

FILTER

CHECK TEST

TEMP.

TIMER SET

B

C

A

STAND BY
DEFROST

INDOOR UNIT
ADDRESS NO

ERROR CODE
OA UNIT ADDRESS NO

CENTRALLY CONTROLLED

CLOCK

ON OFF

˚C

1Hr.

NOT AVAILABLE

˚C

CHECK MODE

FILTER

CHECK

FUNCTION

STAND BY
DEFROST

INDOOR UNIT
ADDRESS NO

ERROR CODE
OA UNIT ADDRESS NO

CENTRALLY CONTROLLED

CLOCK

ON OFF

˚C

1Hr.

NOT AVAILABLE

˚C

CHECK MODE

FILTER

CHECK

FUNCTION

a)

D

E

F

Function table

Select unit number 00

Mode
Power failure automatic recovery

Indoor temperature detecting

LOSSNAY connectivity

Power voltage

Auto mode (only for PUHZ)

Select unit numbers 01 to 03 or all units (AL [wired remote controller]/07 [wireless remote controller])

Mode
Filter sign

Fan speed

No. of air outlets

Installed options (high-performance filter)

Up/down vane setting

Energy saving air flow
(Heating mode)

Settings
Not available
Available
Indoor unit operating average
Set by indoor unit’s remote controller
Remote controller’s internal sensor
Not Supported
Supported (indoor unit is not equipped with outdoor-air intake)
Supported (indoor unit is equipped with outdoor-air intake)
240 V
220 V, 230 V
Energy saving cycle automatically enabled
Energy saving cycle automatically disabled

Settings
100 Hr
2500 Hr
No filter sign indicator
Standard (PLH/PLA)/Silent (PCH/PCA)
High ceiling 1 (PLH/PLA)/Standard (PCH/PCA)
High ceiling 2 (PLH/PLA)/High ceiling (PCH/PCA)
4 directions
3 directions
2 directions
Not supported
Supported
No vanes
Equipped with vanes (vanes angle setup 1)
Equipped with vanes (vanes angle setup 2)
Disabled
Enabled

Mode no. Setting no.

01

1
2
1

02 2

3
1

03 2

3

04

05

1
2
1
2

Mode no. Setting no.

1

07 2

3
1

08 2

3
1 —

09 2 —

3 —

10

1
2
1

11

2
3

12

1
2

Initial setting

Initial setting

Setting

Setting

7. Test run

7.1. Before test run

s After completing installation and the wiring and piping of the indoor and outdoor

units, check for refrigerant leakage, looseness in the power supply or control
wiring, wrong polarity, and no disconnection of one phase in the supply.

s Use a 500-volt megohmmeter to check that the resistance between the power

supply terminals and ground is at least 1.0 M

Fig. 7-1

8

Fig. 7-2

s Do not carry out this test on the control wiring (low voltage circuit) termi-

nals.
Warning:

ΩΩ

Insulation resistance

ΩΩ

Do not use the air conditioner if the insulation resistance is less than 1.0 M

Ω.

ΩΩ

Ω.

ΩΩ

7.2. Test run

The following 3 methods are available.

7.2.1. Using wired remote controller (Fig. 7-1)

1 Turn on the power at least 12 hours before the test run.
2 Press the [TEST] button twice. ➡ “TEST RUN” liquid crystal display
3 Press the [Mode selection] button. ➡ Make sure that wind is blown out.
4 Press the [Mode selection] button and switch to the cooling (or heating) mode.

➡ Make sure that cold (or warm) wind is blown out.

5 Press the [Fan speed] button. ➡ Make sure that the wind speed is switched.
6 Switch the wind direction by pressing the [Airflow] or [Louver] button.

➡ Make sure that horizontal outlet, downward outlet, and other wind direction

adjustments are possible.

➡ Check operation of the outdoor unit fan.

7 Release test run by pressing the [ON/OFF] button. ➡ Stop
8 After the checks, always turn off the power.

7.2.2. Using SW4 in outdoor unit

Refer to the outdoor unit installation manual.

7.3. Self-check

7.3.1. Wired remote controller (Fig. 7-2)

1 Turn on the power.
2 Press the [CHECK] button twice.
3 Set refrigerant address with [TEMP] button if system control is used.
4 Press the [ON/OFF] button to stop the self-check.

A CHECK button
B Refrigerant address
C TEMP. button
D IC: Indoor unit

OC: Outdoor unit

E Check code
F Unit address

7. Test run

• For description of each check code, refer to the following table.

1 Check code Symptom 2 Buzzer sound 3 OPE LED
P1 Intake sensor error Single beep × 1 Lit for 1 sec. × 1
P2 Pipe sensor error Single beep × 2 Lit for 1 sec. × 2
P4 Drain sensor error Single beep × 4 Lit for 1 sec. × 4
P5 Drain pump error Single beep × 5 Lit for 1 sec. × 5
P6 Freezing/Overheating safeguard operation Single beep × 6 Lit for 1 sec. × 6
P8 Pipe temperature error Single beep × 8 Lit for 1 sec. × 8
P9 TH5 sensor error Single beep × 2 Lit for 1 sec. × 2
U0–UP Outdoor unit error Double beep × 1 Lit for 0.4 sec. + 0.4 sec. × 1
F1–FA Outdoor unit error Double beep × 1 Lit for 0.4 sec. + 0.4 sec. × 1
E0–E5 Signal error between remote controller and indoor units Sounds other than above Lights other than above
E6–EF Communication error between indoor and outdoor units Sounds other than above Lights other than above
– – No alarm history No sound Not lit
F F F F No unit Triple beep Not lit

• On wireless remote controller

2 The continuous buzzer sounds from receiving section of indoor unit.
3 Blink of operation lamp

• On wired remote controller

1 Check code displayed in the LCD.

• If the unit cannot be operated properly after the above test run has been performed, refer to the following table to remove the cause.

Wired remote controller LED 1, 2 (PCB in outdoor unit)

H0

H0 → Error code

Display messages do not appear even
when operation switch is turned ON
(operation lamp does not light up).

Symptom

For about 2
minutes following
power-on

After about 2
minutes has
expired following
power-on

After LED 1, 2 are lighted, LED 2 is turned off,
then only LED 1 is lighted. (Correct operation)

Only LED 1 is lighted. → LED 1, 2 blink.

Only LED 1 is lighted. → LED 1 blinks twice,
LED 2 blinks once.

• For about 2 minutes following power-on, operation of the
remote controller is not possible due to system start-up. (Cor­rect operation)

• Connector for the outdoor unit’s protection device is not con­nected.

• Reverse or open phase wiring for the outdoor unit’s power
terminal block (L1, L2, L3)

• Incorrect wiring between indoor and outdoor units (incorrect
polarity of S1, S2, S3)

• Remote controller wire short

Cause

On the wireless remote controller with condition above, following phenomena takes place.

• No signals from the remote controller are accepted.

• OPE lamp is blinking.

• The buzzer makes a short piping sound.

Note:
Operation is not possible for about 30 seconds after cancellation of function selection. (Correct operation)

For description of each LED (LED1, 2, 3) provided on the indoor controller, refer to the following table.

LED1 (power for microcomputer) Indicates whether control power is supplied. Make sure that this LED is always lit.

LED2 (power for remote controller) Indicates whether power is supplied to the remote controller. This LED lights only in the case of the

LED3 (communication between indoor and outdoor units) Indicates state of communication between the indoor and outdoor units. Make sure that this LED is

indoor unit which is connected to the outdoor unit refrigerant address “0”.

always blinking.

9

This product is designed and intended for use in the residential,

commercial and light-industrial environment.

The product at hand is
based on the following
EU regulations:

• Low Voltage Directive 73/23/ EEC

• Electromagnetic Compatibility Directive 89/

336/ EEC

Please be sure to put the contact address/telephone number on

this manual before handing it to the customer.

HEAD OFFICE: MITSUBISHI DENKI BLDG., 2-2-3, MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN

BG79U334H01

Printed in Japan