Mitsubishi Electric MR-385EK, MR-420EKL, MR-455EK, MR-385EKL, MR-455EKL Operating Instructions Manual
...
MR-385EK, MR-385EKL,
MR-420EK, MR-420EKL,
MR-455EK, MR-455EKL
SERIES MODEL
OPERATING INSTRUCTIONS
It is strongly recommended to use only lukewarm water and a soft cloth when cleaning.
Cleaning agents can cause cracking to the plastic components of your refrigerator.
Cleaning Instruction - Important!
2
Safety Precautions
The types of danger that
can result from improper
handling are explained in
the sections below.
Warning
Caution
Warning
Caution
Mishandling can lead to
serious injury or death.
Mishandling can lead to
bodily injury or loss of home
and household contents.
The symbols illustrated below
have the following meanings.
Do not do
Do not touch
Do not take apart,
repair or convert
Do not get wet
Do not touch with
wet hands
Always follow
instructions
Always connect
an earth wire
Always unplug
electrical plug
from socket
When something abnormal or
unusual occurs, turn off immediately
and consult with “the store where
you purchased the unit” or with a
“Mitsubishi Electric repair counter.”
When installing your unit
About the electrical outlet and electrical plug
Installing and Transporting About Using
Page 5
Page 5
Page 10
Page 5
Allow some space around the refrigerator.
If the refrigerant (gas)
leaks, it can remain in
the area and there’s a
risk that it may cause
a fire or explosion.
Leave space around unit
Do not install in an outdoor area where water
can get on it or where there is a lot of moisture.
Due to insulation failure,
it may cause an electric
shock or fire.
Do not get wet
If the power cord is damaged.
If the power cord is damaged call
Mitsubishi Electric Service Centre
for a technician to replace power cord.
The power cord should be designed
for this model.
Service Call
When replacing the interior refrigerator
light or when taking care of the unit, pull
out the electrical plug.
Not doing so can result
in an electric shock or
injury.
Pull out the plug
Do not use damaged cords or plugs
or loose outlets.
Using them can result
in an electric shock or
injury.
Do not use
Remove dust from the electrical plug.
Not doing so can
cause a fire from
insulation failure.
Remove dust
Install on a strong level floor and adjust
the adjustable legs to fix firmly.
The refrigerator may
move and cause injury.
Make sure it’s level
When carrying, use the handles made
for carrying.
If other parts are
held while carrying,
it can cause injury.
Use carrying handles
Do not force food items into the refrigerator.
Do not use force to pull out shelves.
Food items may
fall out, causing
injury.
Do not do
Do not touch foods or containers in the
freezer compartment with wet hands.
Doing so can
cause freezer
burn.
Do not use wet hands
Do not push the electrical plug with the
back of the refrigerator. Do not damage
the electrical cord.
If the plug is pressed by the refrigerator,
or if the cord is bent, bundled, or a
heavy object is placed on it, it can
cause an electric shock or a fire.
Do not do
Do not remove the electrical plug by
pulling the cord.
The cord can become
damaged and can
cause an electric
shock or a fire.
Do not do
Do not plug or unplug the electrical plug
with wet hands.
It can cause an
electric shock.
Do not use wet hands
Use a dedicated outlet for the power supply that meets the
rating specified on the rating label.(The rating label is located
on the door-liner of the refrigerator compartment.)
Using an extention cord or plugging
in too many power cords into the
outlet can cause heat
buildup or a fire.
Only use on outlet that meets
the specified rating.
Keep the electrical plug cord facing downwards
and insert the plug in fully.
If it is plugged with the cord
facing upward, extra pressure
gets exerted on it which can
cause it to heat up or ignite.
Plug with cord downward
Page 5
3
Do not put any vessels, jars, etc. that
contain water on top of the refrigerator.
If water gets onto
electrical parts, it
will cause an electric
shock or a fire.
Do not get wet
Do not place items on top of the refrigerator.
Items may drop from
opening and closing
the door and can
cause injury.
Do not do
Do not hang on the door or door handle, and
do not get on compartment
drawer-type doors.
The refrigerator can
topple over causing injury.
Do not do
If you sense a gas leakage, do not touch
the refrigerator. Open the window and
ventilate the room.
A spark from the electrical
contact can cause an
explosion or a fire.
Ventilate the room
Do not use in a shed or a garage.
If small animals damage the
wiring, it can cause an electric
shock or a fire.
Do not use
Do not use electrical products inside
the refrigerator unit.
If the refrigerant (gas) is leaking
inside the unit, there is a risk that
a spark from the electrical product’s
contact can be a source for ignition or explosion.
Do not do
Do not store pharmaceuticals or scientific
test material.
Anything that needs strict
supervision must not be
stored in a home-use
refrigerator.
Do not store
When opening and closing the door,
be careful not to let it hit any
surrounding furniture.
There is a risk of injury and
the door or furniture is damaged.
Prohibited
Do not wash with water or spill liquid
food items on the unit.
If water and food liquids get
on the unit, it can cause an
electric shock or a fire. If that
happens, dry off immediately.
Do not get wet
Do not store volatile products that
can easily ignite.
Benzine, cosmetics and
hair styling products can
be the cause for igniting
fires and explosion.
Do not store
Do not damage the refrigerant circuit (piping)
of the refrigerator; do not drive in screws.
Because a flammable
refrigerant (gas) is used,
there is the danger of
igniting or explosion.
Do not do
Do not use flammable sprays nearby.
A spark from the
electrical contact
can ignite and
cause a fire.
Do not use
If the refrigerant circuit (piping) is damaged,
do not touch the refrigerator, open the window
and ventilate the room.
When the refrigerant circuit is
damaged, please consult the store
in which the unit was purchased.
Ventilate the room
If there is a possible danger of a child getting
trapped inside while the refrigerator is not in use,
please pull off the door seal.
It is dangerous if the
child gets shut inside.
Remove the door seal
If something abnormal occurs (such as a
burning smell), pull out the electrical plug
and stop the refrigerator from running.
If it continues to run in an
abnormal state, it can cause
an electrical shock or a fire.
Pull out the plug
If you will not be using the refrigerator for a long
period of time, after pulling out the electrical plug,
open the door and let the interior dry out.
If it is not dried adequately, the cooling unit may
corrode causing the refrigerant (gas) to leak which
can then cause the danger of ignition or explosion.
Dry properly
Do not take apart, repair or convert.
Do not continue to use with damaged parts.
This can cause injury,
an electric shock or
a fire.
Do not take apart
When disposing of the unit, transfer it to the
store that you purchased it or to the municipality.
If it is neglected and refrigerant (gas)
leaks, ignition or an explosion may be
caused due to heat from a fire.
Transfer it over
Do not store bottles in the freezer
compartment.
If the center freezes
and bottles crack,
it will cause injury.
Do not store
Do not place your hands or feet
under the refrigerator.
You can get injured
from something such
as the steel plate.
Do not touch
Do not eat foods that have a bad smell
or are discolored.
Doing so may cause
food poisoning or
other illnesses.
Do not do
Close the door by holding the handle.
Hold it in a way so that
you don’t get your fingers
caught in the door.
Not doing this may cause injury.
Hold the handle
When opening and closing the door.
Do not open or close the door while
someone else is in the way.
Do not place your fingers at the top of
drawer-type doors when closing the door.
Do not close the lower drawers with
your foot (as it may get caught).
Do not open or close the door
forcefully (food items may
fall and cause injuries)
Do not do
Warning
Caution
About using your refrigerator
About Malfunctions / Long Term Care
About Using Your Unit
This appliance is not intended for use by young children or infirm persons unless they have been
adequately supervised by a responsible person to ensure that they can use the appliance safely.
Young children should be supervised to ensure that they do not play with the appliance.
This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance by a person responsible for
their safety. Children should be supervised to ensure that they do not play with the appliance.
WARNING - Do not use mechanical devices or
other means to accelerate the defrosting process,
other than those recommended by the manufacturer.
WARNING - Do not use electrical appliances
inside the food storage compartments of
the appliance, unless they are of the type
recommended by the manufacturer.
4
1. Components
This illustration shows series models MR-385EK, MR-420EK, MR-455EK
Toe Grille
(MR-385EK/420EK:3 PCS.)
(MR-455EK
:4 PCS.)
Sliding case
LED Light
Drain Pan
Vegetable Case
Glass Shelf
Temperature Control
(refrigerator compartment)
Temperature Control
(freezer compartment)
Shelf
Ice Tray
Ice Cube Box
Bottle Stopper
(MR-385EK/420EK:2 PCS.)
(MR-455EK
:3 PCS.)
Free Pocket
Door Gasket
Leveling Legs
Bottle Pocket
Adjustable Pocket
Freezer Pocket
Door Gasket
Egg Rack
This illustration shows series models MR-385EKL, MR-420EKL, MR-455EKL
Toe Grille
(
MR-385EKL/420EKL
:3 PCS.)
(MR-455EKL
:4 PCS.)
Sliding case
LED Light
Drain Pan
Vegetable Case
Glass Shelf
Temperature Control
(refrigerator compartment)
Temperature Control
(freezer compartment)
Shelf
Ice Tray
Ice Cube Box
Bottle Stopper
(
MR-385EKL/420EKL
:2 PCS.)
(MR-455EKL
:3 PCS.)
Free Pocket
Door Gasket
Leveling Legs
Bottle Pocket
Adjustable Pocket
Freezer Pocket
Door Gasket
Egg Rack
5
2. Installation
3. Electrical Connections
50mm
454mm
1334mm
20mm 20mm
100mm
Toe Grille
Leveling Leg
Install on a completely flat and rigid surface.
Using the two front adjustable feet, ensure that the
refrigerator is positioned firmly and level on the floor.
Now open the doors approximately half way,
and extend the front adjustable feet equally until
the doors close by themselves.
To ensure adequate ventilation for your refrigerator,
spaces of 20mm on both sides, 50mm at the rear,
and 100mm above the refrigerator are recommended.
Insufficient spacing will decrease cooling efficiency,
resulting in unnecessary energy consumption.
Choose a location which is not exposed to sunlight,
is relatively free from dust, heat and humidity,
and offers good ventilation in order to guarantee
that heat radiation will not be impaired.
During Transport
Before transporting, wipe dry the evaporating
pan, which is located at the rear.
Carry the refrigerator holding the handles
located at the rear and bottom.
Important: For personal safety, this appliance must be properly grounded.
The refrigerator should always be plugged into its own individual electrical outlet.
This is recommended for best performance and also in order to prevent the overloading of household wiring
circuits, which may cause a fire hazard. Extension cords are not recommended.
Make sure that the outlet provides the correct voltage.
If your refrigerator has a grounding plug, use it correctly. The 3-point plug must be inserted into a mating
3-point grounded receptacle. If the installation location does not have a proper 3-point grounding wall
receptacle, the proper type must be installed. The ground point should never be cut or removed.
If your refrigerator has an ungrounding plug, connect the ground wire to the ground connection screw
provided at the lower rear side of the refrigerator.
Corrosion control treatment may be required for the refrigerant circuit (pipe) due to generation of corrosive gases.
Contact the retail store where you purchased the refrigerator.
Use in hot spring areas
Do not obstruct the refrigerator vents or the space around the refrigerator.
If refrigerant leaks, it may accumulate and catch fire or explode.
Warning
Warning
Although R600a refrigerants are combustible, the refrigerant circuit is hermetically sealed and normally leaks will not occur.
Then, contact the retail store where you purchased the refrigerator.
Should the refrigerant circuit be damaged:
1. Do not use flames or electrical appliances nearby.
2. Open the windows to fully ventilate the room.
Do not damage the refrigerant circuit (pipes) or drive screws into it.
Remove the energy label carefully. A glue residue may remain,
particularly if the label has been in place for a long period of time.
Apply either Eucalyptus or Tea Tree oil directly on any residue.
Do not allow the oil to run or drip onto plastic parts as it may
cause the plastic to degrade and potentially crack over time.
Allow the oil to sit for approximately 1-2 minutes,
or until the glue residue has softened.
Wipe off with a damp cloth.
If any residue remains, repeat the above process.
Rinse with clear water.
Dry thoroughly.
How to remove the energy label
4. Operation
Temperature Control of the Refrigerator Compartment
Temperature Control of the Freezer Compartment
6
2. Automatic Defrosting
3. Ice-making
1. Temperature Control
Both the freezer compartment and the refrigerator compartment have a temperature control.
“MID” is recommended for normal usage.
Turn the dial to “COLDER” when storing a large quantity of frozen foods, ice cream etc., in the freezer compartment.
Turn the dial to “FREEZER” when only using the freezer compartment to make ice.
“MID” is recommended for normal usage.
If you would like items in the refrigerator compartment to be colder, turn the dial to “COLDER”.
If the items are too cold or freeze in the refrigerator compartment, turn the dial to “REFRIGERATOR”.
Pour water up to the water line in each of the ice tray sections. Insert the tray completely into the ice tray
holder. If too much water is added, the ice cubes cannot be easily separated from the ice tray.
Once the ice cubes have been made, turn the lever until they fall into the ice cube storage box.
If you attempt to make ice directly in the ice cube storage box, the box will break.
The defrosting heater provides automatic defrosting in the refrigerator according to the accumulated time
calculated by the microcomputer,
so there is no need to defrost it manually. Water produced during defrosting passes through the drainage
hose at the rear and collects in the drain pan in the lower rear part of the refrigerator. Then, it automatically
evaporates with heat from the refrigerant pipe, which is utilized as a radiator.
7
Fig. 1 Fig. 2
Sliding case
Open by pulling the case out.
Lid
CAUTION:
Before closing the refrigerator compartment door, make sure that the sliding case is pushed
all the way in (and the lid is closed correctly).
This sliding case is cooled to a low temperature in order to preserve the freshness of foods stored for long periods.
4. Sliding Case
Remove the lid and sliding case as shown in the illustration and proceed with cleaning.
Pull the case out. Open the lid and then pull out holding the right and left hand sides (Fig. 1).
Pull the case out all the way. Pull out by holding and lifting the edge of the case upwards (Fig. 2).
5. Ice-making Corner Shelf
The shelf may be adjusted vertically in order to store food of various sizes.
6. Shelf (refrigerator)
The shelves may be adjusted vertically in order to store food of various sizes.
8
Fig. 1 Fig. 2 Fig. 3
The door racks may be used to store all those little items that seem to get in the way. If you put all the
small items in one place, you’ll find that there’s more space inside the refrigerator for larger items.
7. Door Racks
Many eggs may be stored in the free pocket (Fig. 1).
If you turn half the egg tray over, small items may be stored together with the eggs (Fig. 2).
You can even turn the whole egg tray over and store small items in the free pocket instead of eggs (Fig. 3).
Free Pocket with Egg Tray
The shelves may be adjusted vertically in order to store food of various sizes.
Large containers such as beer bottles may be accommodated in the upper bottle pocket if the
adjustable pocket is installed in the upper position.
Adjustable Pocket
Even large bottles may be stored in this pocket.
Bottle Pocket
Some types of commercial water cooler bottles may touch the shelf or foodstuffs when placed in the
door pocket, preventing the door from closing firmly.
Free Pocket Adjustable Pocket Bottle Pocket
Remove the door racks as shown in the illustration in order to proceed with cleaning.
This pocket may be removed by pushing it gently upwards.
8. How to Remove the Pockets
9
5. Maintenance
CAUTION
Do not apply water directly onto the refrigerator.
This may result in malfunction, power leakage or fire.
The drain pan becomes dirty very easily and if not cleaned regularly, produces bad odours. Get into the habit
of cleaning this pan regularly.
Dip a soft cloth into cold or lukewarm water, wring it out well and wipe.
If you do not clean the door gasket (especially the lower part) when it is dirty, the gasket will easily become
damaged. Therefore, keep it clean at all times.
Do not clean with cleanser, acids, benzine, thinner, boiling water, soap powder, chemical cloths or neutral
detergent. These will damage the paint finish and external surfaces of your refrigerator.
When performing maintenance, make absolutely sure that the power plug is first disconnected from the power outlet.
How to Replace the LED Light
In the event that the LED light is damaged or malfunctions, please refrain from adjusting
or repairing it by yourself.
Please contact the service center instead.
6. How to attach and insert vegetable case cover
Refrigerator compartment shelf
Vegetable case cover
Attach Vegetable case cover with compartment shelf. Insert the Vegetable case cover into the rails of
Refrigerator compartment shelf, after that slide up the
Vegetable case cover and fit to the compartment shelf.
As shown in the picture.
Insert the attached Vegetable case cover and compartment shelf into the rails (both left and right) upon
the vegetable case.
Then insert the vegetable case.
10
When the refrigerator fails to operate
Check for a power failure.
Check if the power cord is plugged into the power outlet.
Check that the fuse (or circuit-breaker) has not blown.
7. What to do in these situations
8. Troubleshooting
When the refrigerator is cooling excessively
The temperature control dial may be set too high.
If you place foodstuffs containing a lot of moisture directly under the cool air outlets, they will freeze easily.
This does not indicate a malfunction.
When you hear a sound similar to flowing water
The sound of flowing water is the flow of refrigerant (cooling gas). This does not indicate a malfunction.
When noise is produced by the fan grill of the refrigerator
The noise produced by the fan grill will stop at a certain fixed temperature. The airflow cooling system
inside the refrigerator is powered by the operation of the fan motor and fan grill.
When noise is produced while the refrigerator door is open
When you open a door panel, plastic components switch swiftly between hot and cold, and this may
produce noise. When the door is closed, the noise will remain until the difference in temperature is
reduced.
When there’s a power failure.
Minimize opening/closing of doors and avoid putting in more food.
When not in use for a long time.
Clean the Ice cube box and Ice tray, clean the interior after unplugging the refrigerator,
and keep the door open for 2 - 3 days to let it get dry.
If not allowed to dry properly, mold and odors can occur, or refrigerant (gas)
may leak due to corrosion of the cooling unit.
When transporting.
When moving the unit / when changing the direction of the unit.
1. Discard the water/ice from the Ice cube box and the Ice tray.
2. Use protective gear (protective gloves).
3. Lay towels under the water discharge outlet and under the back corners of the refrigerator,
and place a container or tray on the floor that’s about 3 cms high to catch water.
1.
Lift the adjustable legs.
2.
Move in a forward or backward direction. If moved other than a in forward or backward direction, there’s a risk of damaging the floor.
3. When changing the direction of the unit, please use caster wheels or place a protective cloth under the back legs.
Do not damage the refrigerant circuit, do not drive in screws, etc.
The unit uses a flammable refrigerant, so if the gas leaks out, there is the risk of ignition or an explosion.
4. Slowly tilt the refrigerator back to an angle of over 30 degrees, discharge water of the evaporator
tray through the water discharge outlet (the evaporator tray is not visible from the outside.)
5. With more than 2 persons, calmly and slowly transport the unit by grasping the
front side’s lower section inner edge and the back side’s upper section handle.
Towels prevent water from spilling on the floor and damage to the floor.
Have 2 or more persons do this work because the unit is heavy.
Avoid having young children or those without confidence do this work.
Please seek advice from a moving company.
Do not lay or load on its side (it will cause damage to the compressor.)
Water discharge outlet
Page 4
Page 5
Front side - lower
section inner edge
Back side - upper
section handle
Warning
11
CAUTION
1. This appliance is designed for use in ambient temperature listed below.
The internal temperatures could be affected by such factors as the location of the refrigerating appliance, ambient
temperature and the frequency of door opening, and, if appropriate, a warning that the setting of any temperature
control device might have to be varied to allow for these factors.
2.
A rise in temperature of the frozen food during manual defrosting, maintenance or cleaning could shorten the storage life.
3. Food to be frozen is not to be placed in direct contact with food in storage and, if appropriate, that it could be
necessary to reduce the quantity to be frozen if freezing every day is anticipated.
4. The electrical power failure for 1-2 hour will only slightly effect the inside temperature. However, open & close of
the door results in the temperature loss. In case there is more than 24 hours electrical power failure, the food
should be taken out from the fridge.
5. In case you are leaving or there is no food in the fridge for more than 3 weeks, The fridge should be unplugged
and cleaned.
MODEL NAME AMBIENT TEMPERATURE RANGE CLIMATIC CLASS
MR-385EK/EKL, 420EK/EKL, 455EK/EKL-A 16
o
C ~ 43 oC T
MR-385EK/EKL, 420EK/EKL, 455EK/EKL-NZ 16
o
C ~ 43 oC T
When the refrigerator is not cooling sufficiently
The food may be packed too tightly together, which blocks the flow of cool air.
You may have put hot or too many items into the refrigerator.
The door may not have been closed properly.
The door gasket may be damaged.
The refrigerator may not be well-ventilated.
There may be insufficient clearance between the refrigerator and the surfaces immediately beside and above.
The temperature control dial may not be properly set.
When the front of the refrigerator cabinet heats up
In order to safeguard against condensation, there is an anti-condensation pipe which heats up the front of
the cabinet when actuated. When the front of the cabinet is warm, this does not indicate a malfunction.
The more often the door is opened and closed, the more often the anti-condensation pipe is actuated.
It is also actuated immediately after the refrigerator has been installed. In other words, the front of the
cabinet often heats up.
When condensation forms on the exterior of the refrigerator
Condensation may form on the exterior when humidity is high, such as during the wet season.
This is comparable to condensation forming on the outside of a glass when chilled water is poured in;
therefore, it does not indicate a failure. Wipe dry with a dry cloth.
When the power plug is disconnected and reconnected, and the compressor ceases to rotate
When the power plug is disconnected from the power outlet and then immediately plugged in again, the
compressor may not restart. Therefore, when unplugging the refrigerator, always wait at least 5 minutes
before plugging it in again. If the compressor ceases to rotate completely, keep the refrigerator unplugged
and wait at least 5 minutes before plugging it in again.
When the side panel of the cabinet heats up
The side panel of the cabinet will heat up when the door is opened and closed frequently, when installing
the unit and when the unit operates in summer in high temperatures. In such cases, do not touch the panel.
This heat buildup is due to the dissipation of heat absorbed from inside the cabinet over the whole of the
side panel and does not indicate something wrong with the unit.
NZ79C000H01
348 Victoria Road, Rydalmere NSW 2116
For more information and support contact
www.mitsubishielectric.com.au
Call 1300 651 808
SOLE AGENT in Australia
MITSUBISHI ELECTRIC AUSTRALIA PTY LTD.
(Incorporated in New South Wales) ABN 58 001 215 792
Wellington Office (Head Office)
1 Parliament Street Lower Hutt PO Box 30772 Phone: (04) 560 9147, Fax: (04) 560 9133
Auckland Office
Unit 1, 4 Walls Road Penrose PO Box 12726 Phone: (09) 526 9347, Fax: (09) 526 9348
Christchurch Office
44 Halwyn Drive Hornby PO Box 16904 Phone: (03) 341 2837, Fax: (03) 341 2838
SOLE AGENT in New Zealand
BLACK DIAMOND TECHNOLOGIES LIMITED (BDT)
This refrigerator uses flammable foaming gas for
insulation.
Please deliver the unit to specialized industrial
waste dealer when you do away it.
Please follow the rules in your country.
WARNING - Do not use mechanical devices or
other means to accelerate the defrosting process,
other than those recommended by the manufacturer.
WARNING - Do not use electrical appliances
inside the food storage compartments of the
appliance, unless they are of the type
recommended by the manufacturer.
WARNING - Just in case of having damaged the
refrigerant circuit, do not use electric items or
fire equipments near by, and open the window
to ventilate the room. And contact the retail
store at which you purchased it or the following
MITSUBISHI ELECTRIC SERVICE CENTRE.
The appliance is not intended for use by young
children or infirm persons without supervision.
Young children should be supervised to ensure
that they do not play with the appliance.
The refrigeration system behind and inside the
refrigerator contains refrigerant.
Do not allow any sharp objects to come into
contact with the refrigeration system.
The refrigerator contains flammable refrigerant
(R600a: isobutane).
The user manual should be handed over to any
person who would use or handle the refrigerator
whenever the refrigerator would be transferred to
another location and delivered to a recycling plant.
Do not block the openings on the circumstances
of the refrigerator.
Do not store explosive substances such as aerosol
cans with a flammable propellant in this appliance.
This appliance is intended to be used in household
application only.
If an abnormality or malfunction occurs, stop operation immediately and contact the retail store where
you purchased the refrigerator or a MITSUBISHI ELECTRIC SERVICE CENTRE or its service agent.
R600a Refrigerant Warning
NOTE: MITSUBISHI ELECTRIC AUSTRALIA PTY LTD. DO NOT ALLOW SERVICE
TO THE REFRIGERATION CIRCUIT OF THIS APPLIANCE.
This appliance contains a small quantity of R600a refrigerant which is flammable.
During transportation and installation, ensure that the tubing of the refrigerant circuit is not damaged.
Leaking refrigerant can ignite and may damage the eyes.
In the event any damage does occur, avoid exposure to open fires and any device which creates a spark.
Disconnect the appliance from the mains power.
Thoroughly ventilate the room in which the appliance is located for several minutes.
Notify Mitsubishi Electric Australia Pty Ltd. for necessary action and advice.
The room for installing the appliance must be at least 1 cubic metre per 8 grams of refrigerant.
The refrigerant quantity contained in this appliance is noted on the Rating Label of the appliance.
If your Mitsubishi Electric Refrigerator should require service, please contact Mitsubishi Electric Australia
Pty Ltd see back page of this user manual for contact details.
Loading...