Mitsubishi MH8S72BALD-7, MH8S72BALD-8, MH8S72BALD-10 Datasheet
Preliminary Spec.
Some contents are subject to change without notice.
DESCRIPTION
The MH8S72BALD is 8388608 - word by 72-bit
Synchronous DRAM module. This consists of nine
industry standard 8Mx8 Synchronous DRAMs in
TSOP and one industory standard EEPROM in
TSSOP.
The mounting of TSOP on a card edge Dual Inline
package provides any application where high
densities and large quantities of memory are
required.
This is a socket type - memory modules, suitable for
easy interchange or addition of modules.
FEATURES
Frequency
-7
-8
-10
Utilizes industry standard 8M x 8 Synchronous DRAMs
TSOP and industry standard EEPROM in TSSOP
168-pin (84-pin dual in-line package)
single 3.3V±0.3V power supply
100MHz
CLK Access Time
(Component SDRAM)
6.0ns(CL=3)
6.0ns(CL=3)100MHz
8.0ns(CL=3)100MHz
MITSUBISHI LSIs
MH8S72BALD -7,-8,-10
603979776-BIT (8388608 - WORD BY 72-BIT)SynchronousDRAM
85pin
94pin
95pin
124pin
125pin
Back side
1pin
10pin
11pin
Front side
40pin
41pin
Clock frequency 100MHz
Fully synchronous operation referenced to clock rising
edge
4 bank operation controlled by BA0,1(Bank Address)
/CAS latency- 2/3(programmable)
Burst length- 1/2/4/8/Full Page(programmable)
Burst type- sequential / interleave(programmable)
Column access - random
Auto precharge / All bank precharge controlled by A10
Auto refresh and Self refresh
4096 refresh cycle /64ms
LVTTL Interface
Discrete IC and module design conform to
PC100 specification.
(module Spec. Rev. 1.0 and
SPD 1.2A(-7,-8), SPD 1.0(-10))
APPLICATION
PC main memory
168pin
84pin
MIT-DS-0225-0.4
MITSUBISHI
ELECTRIC
( / 55 )
1
29.Oct.1998
Preliminary Spec.
Some contents are subject to change without notice.
PIN NO. PIN NAME PIN NO. PIN NAME PIN NO. PIN NAME PIN NO. PIN NAME
1
2 DQ0 44 NC
3 DQ1 45 /S2
4 DQ2 46 DQMB2
5 DQ3 47 DQMB3
6 VDD 48 NC
7 DQ4 49 VDD
8 DQ5 50 NC
9 DQ6 51 NC
10 DQ7 52
11 DQ8 53
12
13 DQ9 55 DQ16
14 DQ10 56 DQ17
15 DQ11 57 DQ18
16 DQ12 58 DQ19
17 DQ13 59 VDD
18 VDD 60 DQ20
19 DQ14 61 NC
20 DQ15 62 NC
21
22 64 VSS
23 VSS 65 DQ21
24 NC 66 DQ22
25 NC 67 DQ23
26 VDD 68
27
28 DQMB0 70 DQ25
29 DQMB1 71 DQ26
30 /S0 72 DQ27
31 NC 73 VDD
32 VSS 74 DQ28
33 A0 75 DQ29
34 A2 76 DQ30
35 A4 77 DQ31
36 A6 78 VSS
37 A8 79
38
39
40 VDD 82 SDA
41 VDD 83 SCL
42 CK0 84 VDD
VSS
VSS
CB0
CB1
/WE0
A10
BA1
43
54 VSS
63
69 DQ24
80 NC
81
MITSUBISHI LSIs
MH8S72BALD -7,-8,-10
603979776-BIT (8388608 - WORD BY 72-BIT)SynchronousDRAM
VSS 85
86
87
88
89
90
91
92
93
CB2
CB3
NC
VSS 110
CK2
WP
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
VSS 127
DQ32 128
DQ33 129
DQ34 130 DQMB6
DQ35 131 DQMB7
VDD 132
DQ36 133 VDD
DQ37 134 NC
DQ38 135 NC
DQ39 136
DQ40 137
VSS 138 VSS
DQ41 139 DQ48
DQ42 140 DQ49
DQ43 141 DQ50
DQ44 142 DQ51
DQ45 143 VDD
VDD 144 DQ52
DQ46 145 NC
DQ47 146 NC
CB4
CB5
VSS 149 DQ53
NC 150 DQ54
NC 151 DQ55
VDD 152 VSS
/CAS 153 DQ56
DQMB4 154 DQ57
DQMB5 155 DQ58
NC
/RAS 157 VDD
VSS 158 DQ60
A1 159 DQ61
A3 160 DQ62
A5 161 DQ63
A7 162 VSS
A9 163
BA0
A11
VDD 166 SA1
CK1 167 SA2
NC
147 NC
148 VSS
156 DQ59
164 NC
165 SA0
168 VDD
VSS
CKE0
NC
NC
CB6
CB7
CK3
NC = No Connection
MIT-DS-0225-0.4
MITSUBISHI
ELECTRIC
( / 55 )
2
29.Oct.1998
Preliminary Spec.
Some contents are subject to change without notice.
Block Diagram
/S0
DQMB0 DQMB4
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
DQMB1 DQMB5
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
I/O 0
I/O 1
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
I/O 0
I/O 1
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
D0
D1
MITSUBISHI LSIs
MH8S72BALD -7,-8,-10
603979776-BIT (8388608 - WORD BY 72-BIT)SynchronousDRAM
DQM /CSDQM /CS
DQ32
DQ33
DQ34
DQ35
DQ36
DQ37
DQ38
DQ39
DQ40
DQ41
DQ42
DQ43
DQ44
DQ45
DQ46
DQ47
I/O 0
I/O 1
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
DQM /CSDQM /CS
I/O 0
I/O 1
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
D4
D5
/RAS
/CAS
/WE
Vcc
Vss
DQM /CS
I/O 0
I/O 1
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
DQM
/CS
I/O 0
I/O 1
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
DQM
/CS
I/O 0
I/O 1
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
D8
D2 D6
D3
D0 - D8
D0 - D8
D0 - D8
D0 - D8
D0 - D8
CB0
CB1
CB2
CB3
CB4
CB5
CB6
CB7
/S2
DQMB2 DQMB6
DQ16
DQ17
DQ18
DQ19
DQ20
DQ21
DQ22
DQ23
DQMB3 DQMB7
DQ24
DQ25
DQ26
DQ27
DQ28
DQ29
DQ30
DQ31
BA0,BA1,A<11:0> D0 - D8
CK,DQ=10Ω
CK0
CK2
CK1
DQ48
DQ49
DQ50
DQ51
DQ52
DQ53
DQ54
DQ55
DQ56
DQ57
DQ58
DQ59
DQ60
DQ61
DQ62
DQ63
10Ω
10Ω 10Ω
5SDRAMs
4SDRAMs+3.3pF
CK3
10pF 10pF
DQM
/CS
I/O 0
I/O 1
I/O 2
I/O 3
I/O 4
I/O 5
I/O 6
I/O 7
DQM
/CS
I/O 0
I/O 1
I/O 2
I/O 3
I/O 4
I/O 5
D7
I/O 6
I/O 7
CKE0 D0 - D8
SERIAL PD
SCL
WP
47K
A0 A1 A2
SA0 SA1 SA2
SDA
MIT-DS-0225-0.4
MITSUBISHI
ELECTRIC
( / 55 )
3
29.Oct.1998
Preliminary Spec.
Some contents are subject to change without notice.
PIN FUNCTION
MITSUBISHI LSIs
MH8S72BALD -7,-8,-10
603979776-BIT (8388608 - WORD BY 72-BIT)SynchronousDRAM
CK
(CK0 ,2)
CKE0 Input
/S
(/S0,2)
/RAS,/CAS,/WE Input Combination of /RAS,/CAS,/WE defines basic commands.
A0-11 Input
Input
Input
Master Clock:All other inputs are referenced to the rising
edge of CK
Clock Enable:CKE controls internal clock.When CKE is
low,internal clock for the following cycle is ceased. CKE is
also used to select auto / self refresh. After self refresh
mode is started, CKE becomes asynchronous input.Self
refresh is maintained as long as CKE is low.
Chip Select: When /S is high,any command means
No Operation.
A0-11 specify the Row/Column Address in conjunction with
BA.The Row Address is specified by A0-11.The Column
Address is specified by A0-8.A10 is also used to indicate
precharge option.When A10 is high at a read / write
command, an auto precharge is performed. When A10 is
high at a precharge command, both banks are precharged.
BA0,1 Input
DQ0-63,
CB0-7
DQMB0-7 Input
Vdd,Vss
SCL
SDA
SA0-3
Input/Output
Power Supply Power Supply for the memory mounted module.
Input
Output
Input
Bank Address:BA0,1 is not simply BA.BA specifies the
bank to which a command is applied.BA0,1 must be set
with ACT,PRE,READ,WRITE commands
Data In and Data out are referenced to the rising edge of
CK
Din Mask/Output Disable:When DQMB is high in burst
write.Din for the current cycle is masked.When DQMB is high
in burst read,Dout is disabled at the next but one cycle.
Serial clock for serial PD
Serial data for serial PD
Address input for serial PD
MIT-DS-0225-0.4
MITSUBISHI
ELECTRIC
( / 55 )
4
29.Oct.1998
Preliminary Spec.
Some contents are subject to change without notice.
MITSUBISHI LSIs
MH8S72BALD -7,-8,-10
603979776-BIT (8388608 - WORD BY 72-BIT)SynchronousDRAM
BASIC FUNCTIONS
The MH8S72BALD provides basic functions,bank(row)activate,burst read / write,
bank(row)precharge,and auto / self refresh.
Each command is defined by control signals of /RAS,/CAS and /WE at CK rising edge. In
addition to 3 signals,/S,CKE and A10 are used as chip select,refresh option,and
precharge option,respectively.
To know the detailed definition of commands please see the command truth table.
CK
/S Chip Select : L=select, H=deselect
/RAS Command
/CAS Command
/WE
CKE
A10
Command
Refresh Option @refresh command
Precharge Option @precharge or read/write command
define basic commands
Activate(ACT) [/RAS =L, /CAS = /WE =H]
ACT command activates a row in an idle bank indicated by BA.
Read(READ) [/RAS =H,/CAS =L, /WE =H]
READ command starts burst read from the active bank indicated by BA.First output
data appears after /CAS latency. When A10 =H at this command,the bank is
deactivated after the burst read(auto-precharge,READA).
Write(WRITE) [/RAS =H, /CAS = /WE =L]
WRITE command starts burst write to the active bank indicated by BA. Total data
length to be written is set by burst length. When A10 =H at this command, the bank is
deactivated after the burst write(auto-precharge,WRITEA).
Precharge(PRE) [/RAS =L, /CAS =H,/WE =L]
PRE command deactivates the active bank indicated by BA. This command also
terminates burst read / write operation. When A10 =H at this command, both banks are
deactivated(precharge all, PREA).
Auto-Refresh(REFA) [/RAS =/CAS =L, /WE =CKE =H]
REFA command starts auto-refresh cycle. Refresh address including bank address are
generated internally. After this command, the banks are precharged automatically.
MIT-DS-0225-0.4
MITSUBISHI
ELECTRIC
( / 55 )
5
29.Oct.1998
Preliminary Spec.
Some contents are subject to change without notice.
COMMAND TRUTH TABLE
COMMAND MNEMONIC
Deselect DESEL H X H X X X X X X
No Operation NOP H X L H H H X X X
MITSUBISHI LSIs
MH8S72BALD -7,-8,-10
603979776-BIT (8388608 - WORD BY 72-BIT)SynchronousDRAM
CKE
n-1
CKE
n
/S
/RAS
/CAS
/WE BA0,1 A10
A11
X
X
A0-9
Row Adress Entry &
Bank Activate
Single Bank Precharge PRE H X L L H L V L X
Precharge All Bank
Column Address Entry
& Write
Column Address Entry
& Write with Auto-
Precharge
Column Address Entry
& Read
Column Address Entry
& Read with Auto
Precharge
Auto-Refresh REFA H H L L L H X X X
Self-Refresh Entry REFS H L L L L H X X X
Self-Refresh Exit REFSX L H H X X X X X X
Burst Terminate TERM
Mode Register Set
ACT H X L L H H V V V
PREA
WRITE
WRITEA H X L H L L V H V
READ H X L H L H V L V
READA H X L H L H V H V
MRS
H X L L H L X H X
H X L H L L V L V
L H L H H H X X X
H X L H H L X X X
H X L L L L L L
V
X
X
X
X
X
X
X
X
X
X
X
L
V*1
H =High Level, L = Low Level, V = Valid, X = Don't Care, n = CK cycle number
NOTE:
1.A7-9 = 0, A0-6 = Mode Address
MIT-DS-0225-0.4
MITSUBISHI
ELECTRIC
( / 55 )
6
29.Oct.1998
Preliminary Spec.
Some contents are subject to change without notice.
FUNCTION TRUTH TABLE
MITSUBISHI LSIs
MH8S72BALD -7,-8,-10
603979776-BIT (8388608 - WORD BY 72-BIT)SynchronousDRAM
Current State /S /RAS /CAS /WE Address
IDLE H X X X X DESEL NOP
L H H H X NOP NOP
L H H L
L H L X
L L H H
L L H L
L L L H X REFA
L L L L
ROW ACTIVE H X X X X DESEL NOP
L H H H X NOP NOP
L H H L BA
L H L H BA,CA,A10 READ/READA
L H L L BA,CA,A10
L L H H BA,RA ACT Bank Active/ILLEGAL*2
L L H L BA,A10 PRE/PREA Precharge/Precharge All
L L L H X REFA ILLEGAL
L L L L
READ H X X X X DESEL NOP(Continue Burst to END)
L H H H X NOP NOP(Continue Burst to END)
L H H L
L H L H BA,CA,A10 READ/READA
L H L L BA,CA,A10 WRITE/WRITEA
L L H H BA,RA ACT Bank Active/ILLEGAL*2
L L H L BA,A10 PRE/PREA Terminate Burst,Precharge
L L L H X REFA ILLEGAL
L L L L
BA TBST ILLEGAL*2
BA,CA,A10
BA,RA
BA,A10 PRE/PREA NOP*4
Op-Code,
Mode-Add
Op-Code,
Mode-Add
BA
Op-Code,
Mode-Add
Command
READ/WRITE ILLEGAL*2
ACT Bank Active,Latch RA
Auto-Refresh*5
MRS Mode Register Set*5
TBST
WRITE/
WRITEA
MRS ILLEGAL
TBST Terminate Burst
MRS ILLEGAL
NOP
Begin Read,Latch CA,
Determine Auto-Precharge
Begin Write,Latch CA,
Determine Auto-Precharge
Terminate Burst,Latch CA,
Begin New Read,Determine
Auto-Precharge*3
Terminate Burst,Latch CA,
Begin Write,Determine AutoPrecharge*3
Action
MIT-DS-0225-0.4
MITSUBISHI
ELECTRIC
( / 55 )
7
29.Oct.1998
Preliminary Spec.
Some contents are subject to change without notice.
MH8S72BALD -7,-8,-10
603979776-BIT (8388608 - WORD BY 72-BIT)SynchronousDRAM
FUNCTION TRUTH TABLE(continued)
MITSUBISHI LSIs
Current State /S /RAS /CAS /WE Address
WRITE H X X X X DESEL NOP(Continue Burst to END)
L H H H X NOP NOP(Continue Burst to END)
L H H L BA TBST Terminate Burst
L H L H BA,CA,A10
L H L L BA,CA,A10
L L H H BA,RA ACT Bank Active/ILLEGAL*2
L L H L BA,A10 PRE/PREA Terminate Burst,Precharge
L L L H X REFA ILLEGAL
L L L L
READ with H X X X X DESEL NOP(Continue Burst to END)
AUTO L H H H X NOP NOP(Continue Burst to END)
PRECHARGE L H H L BA TBST ILLEGAL
L H L H BA,CA,A10 READ/READA ILLEGAL
L H L L BA,CA,A10
L L H H BA,RA ACT Bank Active/ILLEGAL*2
L L H L BA,A10 PRE/PREA ILLEGAL*2
L L L H X REFA ILLEGAL
L L L L
WRITE with H X X X X DESEL NOP(Continue Burst to END)
AUTO L H H H X NOP NOP(Continue Burst to END)
PRECHARGE L H H L
L H L H BA,CA,A10 READ/READA ILLEGAL
L H L L BA,CA,A10
L L H H
L L H L BA,A10 PRE/PREA ILLEGAL*2
L L L H X REFA ILLEGAL
L L L L
Op-Code,
Mode-Add
Op-Code,
Mode-Add
BA
BA,RA
Op-Code,
Mode-Add
Command
Terminate Burst,Latch CA,
READ/READA
WRITE/
WRITEA
MRS ILLEGAL
WRITE/
WRITEA
MRS ILLEGAL
TBST ILLEGAL
WRITE/
WRITEA
ACT Bank Active/ILLEGAL*2
MRS ILLEGAL
Begin Read,Determine AutoPrecharge*3
Terminate Burst,Latch CA,
Begin Write,Determine AutoPrecharge*3
ILLEGAL
ILLEGAL
Action
MIT-DS-0225-0.4
MITSUBISHI
ELECTRIC
( / 55 )
8
29.Oct.1998
Preliminary Spec.
Some contents are subject to change without notice.
MH8S72BALD -7,-8,-10
603979776-BIT (8388608 - WORD BY 72-BIT)SynchronousDRAM
FUNCTION TRUTH TABLE(continued)
MITSUBISHI LSIs
Current State /S /RAS /CAS /WE Address
PRE - H X X X X DESEL NOP(Idle after tRP)
CHARGING L H H H X NOP NOP(Idle after tRP)
L H H L BA TBST ILLEGAL*2
L H L X BA,CA,A10 READ/WRITE ILLEGAL*2
L L H H BA,RA ACT ILLEGAL*2
L L H L BA,A10 PRE/PREA NOP*4(Idle after tRP)
L L L H X REFA ILLEGAL
Op-Code,
L L L L
Mode-Add
ROW H X X X X DESEL NOP(Row Active after tRCD
ACTIVATING L H H H X NOP NOP(Row Active after tRCD
L H H L BA TBST ILLEGAL*2
L H L X BA,CA,A10 READ/WRITE ILLEGAL*2
L L H H BA,RA ACT ILLEGAL*2
L L H L BA,A10 PRE/PREA ILLEGAL*2
L L L H X REFA ILLEGAL
Op-Code,
L L L L
Mode-Add
Command
MRS ILLEGAL
MRS ILLEGAL
Action
WRITE RE- H X X X X DESEL NOP
COVERING L H H H X NOP NOP
L H H L BA TBST ILLEGAL*2
L H L X BA,CA,A10 READ/WRITE ILLEGAL*2
L L H H BA,RA ACT ILLEGAL*2
L L H L BA,A10 PRE/PREA ILLEGAL*2
L L L H X REFA ILLEGAL
L L L L
MIT-DS-0225-0.4
Op-Code,
MRS ILLEGAL
Mode-Add
MITSUBISHI
ELECTRIC
29.Oct.1998
( / 55 )
9
Preliminary Spec.
Some contents are subject to change without notice.
MH8S72BALD -7,-8,-10
603979776-BIT (8388608 - WORD BY 72-BIT)SynchronousDRAM
FUNCTION TRUTH TABLE(continued)
Current State /S /RAS /CAS /WE Address Command Action
RE- H X X X X DESEL NOP(Idle after tRC)
FRESHING L H H H X NOP
L H H L BA TBST ILLEGAL
L H L X BA,CA,A10 READ/WRITE ILLEGAL
L L H H BA,RA ACT ILLEGAL
L L H L BA,A10 PRE/PREA ILLEGAL
L L L H X REFA ILLEGAL
NOP(Idle after tRC)
MITSUBISHI LSIs
L L L L
MODE H X X X X DESEL NOP(Idle after tRSC)
REGISTER L H H H X NOP NOP(Idle after tRSC)
SETTING L H H L BA TBST ILLEGAL
L H L X BA,CA,A10 READ/WRITE ILLEGAL
L L H H BA,RA ACT ILLEGAL
L L H L BA,A10 PRE/PREA ILLEGAL
L L L H X REFA ILLEGAL
L L L L
Op-Code,
MRS ILLEGAL
Mode-Add
Op-Code,
MRS ILLEGAL
Mode-Add
ABBREVIATIONS:
H = Hige Level, L = Low Level, X = Don't Care
BA = Bank Address, RA = Row Address, CA = Column Address, NOP = No Operation
NOTES:
1. All entries assume that CKE was High during the preceding clock cycle and the current
clock cycle.
2. ILLEGAL to bank in specified state; function may be legal in the bank indicated by BA,
depending on the state of that bank.
3. Must satisfy bus contention, bus turn around, write recovery requirements.
4. NOP to bank precharging or in idle state.May precharge bank indicated by BA.
5. ILLEGAL if any bank is not idle.
ILLEGAL = Device operation and / or date-integrity are not guaranteed.
MIT-DS-0225-0.4
MITSUBISHI
ELECTRIC
( / 55 )
10
29.Oct.1998
Preliminary Spec.
Some contents are subject to change without notice.
MH8S72BALD -7,-8,-10
603979776-BIT (8388608 - WORD BY 72-BIT)SynchronousDRAM
FUNCTION TRUTH TABLE FOR CKE
MITSUBISHI LSIs
Current State
SELF - H X X X X X X
REFRESH*1 L H H X X X X
POWER H X X X X X X
DOWN L H X X X X X
ALL BANKS H H X X X X X
IDLE*2 H L L L L H X
ANY STATE H H X X X X X
other than H L X X X X X
listed above L H X X X X X
CKE
CKE
n-1
L H L H H H X
L H L H H L X
L H L H L X X
L H L L X X X
L L X X X X X
L L X X X X X
H L H X X X X
H L L H H H X
H L L H H L X
H L L H L X X
H L L L X X X
L X X X X X X
L L X X X X X
n
/RAS /CAS /WE Add
/S
Action
INVALID
Exit Self-Refresh(Idle after tRC)
Exit Self-Refresh(Idle after tRC)
ILLEGAL
ILLEGAL
ILLEGAL
NOP(Maintain Self-Refresh)
INVALID
Exit Power Down to Idle
NOP(Maintain Self-Refresh)
Refer to Function Truth Table
Enter Self-Refresh
Enter Power Down
Enter Power Down
ILLEGAL
ILLEGAL
ILLEGAL
Refer to Current State = Power Down
Refer to Function Truth Table
Begin CK0 Suspend at Next Cycle*3
Exit CK0 Suspend at Next Cycle*3
Maintain CK0 Suspend
ABBREVIATIONS:
H = High Level, L = Low Level, X = Don't Care
NOTES:
1. CKE Low to High transition will re-enable CK and other inputs asynchronously.
A minimum setup time must be satisfied before any command other than EXIT.
2. Power-Down and Self-Refresh can be entered only from the All banks idle State.
3. Must be legal command.
MIT-DS-0225-0.4
MITSUBISHI
ELECTRIC
( / 55 )
11
29.Oct.1998
Preliminary Spec.
Some contents are subject to change without notice.
603979776-BIT (8388608 - WORD BY 72-BIT)SynchronousDRAM
SIMPLIFIED STATE DIAGRAM
MITSUBISHI LSIs
MH8S72BALD -7,-8,-10
SELF
REFRESH
REFS
REFSX
WRITE
SUSPEND
MODE
REGISTER
SET
CLK
SUSPEND
TBST(for Full Page) TBST(for Full Page)
CKEL
WRITE
CKEH
WRITEA READA
MRS
CKEH
WRITE
CKEL
WRITEA
WRITE
WRITEA
IDLE
ACT
ROW
ACTIVE
READ
REFA
CKEL
CKEH
READ
READA
READ
READA
AUTO
REFRESH
POWER
DOWN
CKEL
CKEH
READ
SUSPEND
POWER
APPLIED
MIT-DS-0225-0.4
WRITEA
SUSPEND
CKEL
CKEH
POWER
ON
WRITEA
PRE
PRE
PRE PRE
PRE
CHARGE
MITSUBISHI
ELECTRIC
( / 55 )
12
READA
CKEL
CKEH
READA
SUSPEND
Automatic Sequence
Command Sequence
29.Oct.1998
Preliminary Spec.
Some contents are subject to change without notice.
MITSUBISHI LSIs
MH8S72BALD -7,-8,-10
603979776-BIT (8388608 - WORD BY 72-BIT)SynchronousDRAM
POWER ON SEQUENCE
Before starting normal operation, the following power on sequence is necessary to prevent a
SDRAM from damaged or malfunctioning.
1. Apply power and start clock. Attempt to maintain CKE high, DQMB0-7 high and NOP
condition at the inputs.
2. Maintain stable power, stable clock, and NOP input conditions for a minimum of 500us.
3. Issue precharge commands for all banks. (PRE or PREA)
4. After all banks become idle state (after tRP), issue 8 or more auto-refresh commands.
5. Issue a mode register set command to initialize the mode register.
After these sequence, the SDRAM is idle state and ready for normal operation.
MODE REGISTER
Burst Length, Burst Type and /CAS Latency can be programmed by setting the mode
register(MRS). The mode register stores these date until the next MRS command, which may
be issue when both banks are in idle state. After tRSC from a MRS command, the SDRAM is
ready for new command.
LATENCY
MODE
00
CL
0 0 0
0 0 1
0 1 0
0 1 1
1 0 0
1 0 1
1 1 0
1 1 1
A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0BA1BA0
0 0
/CAS LATENCY
WM
R
R
2
3
R
R
R
R
0 0
LTMODE BT BL
BURST
LENGTH
BURST
TYPE
BA0,1 A11-0
BL
0 0 0
0 0 1
0 1 0
0 1 1
1 0 0
1 0 1
1 1 0
1 1 1
0
1
CK
/S
/RAS
/CAS
/WE
BT= 0 BT= 1
1
2
4
8
R
R
R
FP
SEQUENTIAL
INTERLEAVED
V
1
2
4
8
R
R
R
R
WRITE
MODE
MIT-DS-0225-0.4
BURST
0
1
SINGLE BIT
MITSUBISHI
R:Reserved for Future Use
FP: Full Page
29.Oct.1998
ELECTRIC
( / 55 )
13
Preliminary Spec.
Some contents are subject to change without notice.
MITSUBISHI LSIs
MH8S72BALD -7,-8,-10
603979776-BIT (8388608 - WORD BY 72-BIT)SynchronousDRAM
[ /CAS LATENCY]
/CAS latency,CL,is used to synchronize the first output data with the CLK frequency,i.e.,the
speed of CLK determines which CL should be used.First output data is available after CL
cycles from READ command.
/CAS Latency Timing(BL=4)
CK
Command
Address
ACT
tRCD
X
READ
Y
DQ
CL=2
DQ
Q0 Q1 Q2 Q3
CL=3
Q0 Q1 Q2 Q3
CL=2
CL=3
[ BURST LENGTH ]
The burst length,BL,determines the number of consecutive wrutes or reads that will be
automatically performed after the initial write or read command.For BL=1,2,4,8,full page the
output data is tristated(Hi-Z) after the last read.For BL=FP (Full Page),the TBST (Burst
Terminate) command should be issued to stop the output of data.
Burst Length Timing(CL=2)
tRCD
CK
Command
Address
ACT
X
READ
Y
DQ
DQ
DQ
DQ
DQ
MIT-DS-0225-0.4
Q0
Q0 Q1
Q0 Q1 Q2 Q3
Q0 Q1 Q2 Q3 Q5 Q6Q4 Q7
Q0 Q1 Q2 Q3 Q5 Q6Q4 Q7
m=511
MITSUBISHI
ELECTRIC
( / 55 )
14
Q8
Qm Q0 Q1
Full Page counter rolls over
and continues to count.
BL=1
BL=2
BL=4
BL=8
BL=FP
29.Oct.1998
Preliminary Spec.
Some contents are subject to change without notice.
CK
Command
Read
MITSUBISHI LSIs
MH8S72BALD -7,-8,-10
603979776-BIT (8388608 - WORD BY 72-BIT)SynchronousDRAM
Write
Address
DQ
Initial Address
A2 A1 A0
0 0 0
0 0 1
0 1 0
0 1 1
1 0 0
CL= 3
BL= 4
BL
8
Y
Q0 Q1 Q2 Q3
/CAS Latency Burst Length Burst Length
Burst Type
Column Addressing
Sequential Interleaved
0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7
1 2 3 4 5 6 7 0 1 0 3 2 5 4 7 6
2 3 4 5 6 7 0 1 2 3 0 1 6 7 4 5
3 4 5 6 7 0 1 2 3 2 1 0 7 6 5 4
4 5 6 7 0 1 2 3 4 5 6 7 0 1 2 3
Y
D0 D1
D2
D3
1 0 1
1 1 0
1 1 1
- 0 0
- 0 1
- 1 0
- 1 1
- - 0
- - 1
MIT-DS-0225-0.4
5 6 7 0 1 2 3 4 5 4 7 6 1 0 3 2
6 7 0 1 2 3 4 5 6 7 4 5 2 3 0 1
7 0 1 2
0 1 2 3
1 2 3 0
4
2 3 0 1
3 0
0 1
2
1 0
3 4 5 6 3 2 1 0
1 2
7 6 5 4
0 1 2 3
1 0 3 2
2 3 0 1
3 2
0 1
1 0
1 0
MITSUBISHI
ELECTRIC
29.Oct.1998
( / 55 )
15
Preliminary Spec.
Some contents are subject to change without notice.
MITSUBISHI LSIs
MH8S72BALD -7,-8,-10
603979776-BIT (8388608 - WORD BY 72-BIT)SynchronousDRAM
OPERATION DESCRIPTION
BANK ACTIVATE
The SDRAM has four independent banks. Each bank is activated by the ACT command with
the bank address(BA0,1). A row is indicated by the row address A11-0. The minimum
activation interval between one bank and the other bank is tRRD.The number of banks which
are active concurrently is not limited.
PRECHARGE
The PRE command deactivates indicated by BA. When both banks are active, the precharge
all command(PREA,PRE + A10=H) is available to deactivate them at the same time. After tRP
from the precharge, an ACT command can be issued.
Bank Activation and Precharge All (BL=4, CL=3)
CLK
Command
A0-9
A10
2ACT command/tRCmin
ACT
tRRD
Xa
Xa
ACT
Xb
tRCD
Xb
READ
Y
0
tRCmin
tRAS
PRE
1
ACT
tRP
Xb
Xb
A11
BA0,1
DQ
Xa
00
Xb Xb
00
01
Qa0 Qa1 Qa2 Qa3
Precharge all
01
READ
After tRCD from the bank activation, a READ command can be issued. 1st output date is
available after the /CAS Latency from the READ, followed by (BL-1) consecutive date when
the Burst Length is BL. The start address is specified by A8-0, and the address sequence of
burst data is defined by the Burst Type. A READ command may be applied to any active bank,
so the row precharge time(tRP) can be hidden behind continuous output data(in case of BL=8)
by interleaving the dual banks. When A10 is high at a READ command, the
auto-precharge(READA) is performed. Any command (READ, WRITE, PRE, ACT) to the
same bank is inhibited till the internal precharge is complete. The internal precharge start at
BL after READA. The next ACT command can be issued after (BL + tRP) from the previous
READA.
MIT-DS-0225-0.4
MITSUBISHI
ELECTRIC
( / 55 )
16
29.Oct.1998
Preliminary Spec.
Some contents are subject to change without notice.
Multi Bank Interleaving READ (BL=4, CL=3)
CK
Command
A0-9
ACT
tRCD
Xa
MITSUBISHI LSIs
MH8S72BALD -7,-8,-10
603979776-BIT (8388608 - WORD BY 72-BIT)SynchronousDRAM
READ
Y
ACT
Xb
READ
Y
PRE
A10
A11
BA0,1
DQ
Xa
Xa Xb
00
0
00
/CAS latency
Xb
10
Qa0 Qa1 Qa2 Qa3 Qb0 Qb1 Qb2
0
0
10
00
Burst Length
READ with Auto-Precharge (BL=4, CL=3)
CK
BL + tRP
Command
A0-9
A10
A11 Xa Xa
BA0,1
ACT
Xa
Xa
00
READ
tRCD tRP
Y
1
00
BL
ACT
Xa
Xa
00
DQ
CK
Command
CL=3
CL=2
MIT-DS-0225-0.4
Qa0 Qa1 Qa2 Qa3
Internal precharge begins
READ Auto-Precharge Timing (BL=4)
ACT READ
BL
DQ Qa0 Qa1 Qa2 Qa3
DQ Qa0 Qa1 Qa2 Qa3
Internal Precharge Start Timing
MITSUBISHI
ELECTRIC
29.Oct.1998
( / 55 )
17
Loading...