SERIAL INPUT PLL FREQUENCY SYNTHESIZER FOR TV/VCR
DESCRIPTION
The M64893 is a semiconductor integrated circuit consisting of
PLL frequency synthesizer for TV/VCR using Bip process. It
contains the prescaler with operating up to 1.3GHz, 4 band drivers
and Op. Amp for direct tuning.
FEATURES
4 integrated PNP band drivers
•
(Io=40mA,Vsat=0.2V typ@Vcc
•
Built-in Op. Amp for direct tuning voltage output (33V)
•
Low power dissipation (Icc=20mA, Vcc
•
Built-in prescaler with input amplifier (Fmax=1.3GHz)
•
PLL lock/unlock status display out put
(Built-in pull up resistor )
•
X’tal 4MHz is used to realize 1 type of tuning steps
(Division ratio 1/640)
•
Serial data input. (3 wire bus )
•
Built-in Power on reset system
•
Small package (SOP/SSOP)
1
to 13.2V)
=5V)
1
MITSUBISHI IC
M64893FP/GP
PIN CONFIGURATION (TOP VIEW)
PRESCALER
INPUT
GND
SUPPLY
VOLTAGE 1
SUPPLY
VOLTAGE 2
BAND
SWITCHING
OUTPUTS
1
fin
GND
2
3
4
16P2Z-A (GP)
M64893FP/GP
CC1
V
CC2
V
BS4
BS3
BS2
BS1
Outline 16P2S-A (FP)
16
15
14
13
125
116
107
98
Xin
ENA
DATA
CLK
LD/ftest
V
Vtu
Vin
CRYSTAL
OSCILLATOR
ENABLE
INPUT
DATA INPUT
CLOCK INPUT
LD/ftest
OUTPUT
SUPPLY
CC3
VOLTAGE 3
TUNING
OUTPUT
FILTER INPUT
(TV)
S
APPLICATION
TV , VCR tuners
RECOMMENDED OPERATING CONDITION
Supply voltage range..............................................V
Rated supply voltage...........................................................V
V
CC2
CC1
=4.5 to 5.5V
=V
CC1
CC3
V
=28 to 35V
V
V
to 13.2V
CC1
=5V
=12V
CC2
CC3
=33V
FUNCTION
2-modulus prescaler (1/32 and 1/33)
•
Built-in 4MHz crystal oscillator and reference divider
•
Programmable divider (10-bit M counter, 5-bit S counter)
•
Tri-state phase comparator
•
Lock detector
•
Band switch driver
•
Op. Amp for direct tuning
•
1
BLOCK DIAGRAM
CRYSTAL
OSCILLATOR
Xin ENA DATA CLK
16 15 14 13 12 11 10 9
OSC
DIVIDER
1/32,1/33
1/8
ENABLE
SERIAL INPUT PLL FREQUENCY SYNTHESIZER FOR TV/VCR
DATA INPUT
19-BIT SHIFT
REGISTER LATCH
10-BIT M COUNTER
5-BIT S COUNTER
P.O
RESET
MITSUBISHI IC
M64893FP/GP
CLOCK LD/ftest SUPPLY TUNING FILTER
BIAS
OUTPUT
10
5
LD/ftest
VCC1
4
V
CC3 Vtu Vin
LOCK
DETECTOR
PHASE
DETECTOR
BAND DRIVER
AMP
CHARGE
PUMP
INPUTOUTPUTVOLTAGE 3INPUTINPUT
(TV)
S
AMP
fin GND VCC1 VCC2 BS4 BS3 BS2 BS1
PRESCALER
INPUT
SUPPLY
VOLTAGE 1
SUPPLY
VOLTAGE 2
BAND SWITCHING
OUTPUTS
87654321
2
°
°
M64893FP/GP
SERIAL INPUT PLL FREQUENCY SYNTHESIZER FOR TV/VCR
DESCRIPTION OF PIN
Pin No. Symbol Pin name Function
1 fin Prescaler input Input for the VCO frequency.
2 GND GND Ground to 0V.
3V
4V
5
6
7
8
CC1
CC2
BS4
BS3
BS2
BS1
9 Vin
10 Vtu Tuning output This supplies the tuning voltage.
11 V
CC3
12 LD/ftest Lock detect/Test port
13 CLK Clock input Data is read into the shift register when the clock signal falls.
14 DATA Data input Input for band SW and programmable freq. divider set up.
15 ENA Enable input
16 Xin
Power supply voltage 1 Power supply voltage terminal. 5.0V ± 0.5V
Power supply voltage 2 Power supply for band switching, Vcc
to 13.2V
1
PNP open collector method is used.
Band switching outputs
When the band switching data is "H", the output is ON.
When it is "L", the output is OFF.
This is the output terminal for the LPF input and charge pump output. When the
Filter input
(Charge pump output)
phase of the programmable divider output (f 1/N) is ahead compared to the
reference frequency (fref), the "source" current state becomes active.
If it is behind, the "sink" current becomes active.
If the phases are the same, the high impedance state becomes active.
Power supply voltage 3 Power supply voltage for tuning voltage 28 to 35V
When 19 bit data is input,lock detector is output.
When 27 bit data is input, lock detector is output, the programmable freq.
Divider output and reference freq.
Output is selected by the test mode.
This is normally at a "L". When this is at "H", data and clock signals are received.
Data is read into the latch when the 19th pulse of the clock signal falls.
This is connected to the
crystal oscillator
4.0MHz crystal oscillator is connected.
MITSUBISHI IC
(TV)
S
ABSOLUTE MAXIMUM RATINGS
(Ta=-20 ° C to +75 ° C, unless otherwise noted)
Symbol Parameter Conditions Ratings Unit
CC1
V
CC2
V
CC3
V
I
V
O
V
V
BSOFF
I
BSON
BSON
t
d
P
T
opr
T
stg
RECOMMENDED OPERATING CONDITIONS
Supply voltage 1 Pin3 6.0 V
Supply voltage 2 Pin4 14.4 V
Supply voltage 3 Pin11 36.0 V
Input voltage Not to exceed V
CC1
6.0 V
Output voltage LD output 6.0 V
Voltage applied when the band output is
OFF
14.4 V
Band output current Per 1 band output circuit 50.0 mA
ON the time when the band output is ON
50mA per 1 band output circuit
3circuit are pn at same time
10 sec
Power dissipation Ta=+75 ° C 470 mW
Operating temperature -20 to +75
Storage temperature -40 to +125
(Ta=-20 ° C to +75 ° C, unless otherwise noted)
Symbol Parameter Conditions Ratings Unit
V
V
V
f
opr1
f
opr2
CC1
CC2
CC3
Supply voltage 1 Pin3 4.5 to 5.5 V
Supply voltage 2 Pin4 V
to 13.2 V
CC1
Supply voltage 3 Pin11 28 to 35 V
Operating frequency (1) Crystal oscillation circuit 4.0 MHz
Operating frequency (2) 80 to 1,300 MHz
Normally 1 circuit is on. 2 circuits on at the
BDL
I
Band output current 5 to 8
same time is max. It is prohibited to have
0 to 40 mA
3 or more circuits turned on at the same time.
C
C
3