8BIT 12CH I C BUS D–A CONVERTER WITH BUFFER AMPLIFIERS
GENERAL DESCRIPTION
The M62398P,FP is a 12V type CMOS 12-channel D–A
converters with output buffer amplifiers.
It can communicate with a microcontroller via few wiring
thanks to the adoption of the two-line I2C BUS.
The output buffer amplifier employs AB class output with
sinking and sourcing capability of more than 2.5mA ,and an
output voltage range is nearly between ground and VrefU.
Maximum 8 ICs can be connected to a bus by using three
chip-set pins , so that it is possible to handle up to 96
channels.
FEATURES
• I2C BUS serial data method
• Wide output range
Nearly between ground and VrefU(0~12V).
• High output current drive capability
Over ±2.5mA
• 2 setting voltage ranges by dual input pins for upper
voltage references (VrefU1,U2)
MITSUBISHI <Dig./Ana. INTERFACE>
M62398P,FP
2
PIN CONFIGURATION (TOP VIEW)
R
SCL
SDA
Ao7
Ao8
Ao9
Ao10
Ao11
Ao12
VrefL
VrefU1
GND
1
2
3
4
M62398P,FP
5
6
7
8
9
10
11
12 13
Outline
24P4D (P)
24P2N-B (FP)
24
23
22
21
20
19
18
17
16
15
14
CS0
CS1
CS2
VDD
VCC
Ao6
Ao5
Ao4
Ao3
Ao2
Ao1
VrefU2
APPLICATION
Conversion from digital control data to analog control data for both consumer and industrial equipment.
Gain control and automatic adjustment of DISPLAY-MONITOR or CTV.
BLOCK DIAGRAM
VrefU2Vcc Ao1Ao2Ao3Ao4Ao5Ao6VDDCS2CS1CS0
2324
22
CHIP SELECT
ADDRESS
DECODER
I2C BUS TRANSCEIVER
2021
19
8bit upper
segment R-2R
8bit Latch
8
8bit Latch
8bit upper
segment R-2R
R2
R1
8bit upper
segment R-2R
8bit Latch
8bit Latch
8bit upper
segment R-2R
R1
R2
R1
8bit upper
segment R-2R
8bit Latch
8bit Latch
8bit upper
segment R-2R
R1
1415
R2
R1
R2
R1
R1
18
R2
R1
8bit upper
segment R-2R
8bit Latch
8bit Latch
8bit upper
segment R-2R
R1
R2
R1
8bit upper
segment R-2R
8bit Latch
8bit Latch
8bit upper
segment R-2R
R1
1617
R2
R1
8bit upper
segment R-2R
8bit Latch
8bit Latch
8bit upper
segment R-2R
R1
GND
1213
=2.4
R2
2
1
R
SCL SDA VrefLAo7 Ao8 Ao9 Ao10 Ao11 Ao12
3
4 5 6
R2
R2
R2
7
R2
8
MITSUBISHI ELECTRIC
R2
9 10
1997-5-28D.rev
11
VrefU1
( / 7)
1
EXPLANATION OF TERMINALS
MITSUBISHI <Dig./Ana. INTERFACE>
M62398P,FP
8BIT 12CH I C BUS D–A CONVERTER WITH BUFFER AMPLIFIERS
2
PIN No. Symbol
3
1
2
14
15
16
17
18
19
4
5
6
7
8
SDA
R
SCL
Ao1
Ao2
Ao3
Ao4
Ao5
Ao6
Ao7
Ao8
Ao9
Ao10
Ao11
F u n c t i o n
Serial data input terminal
Reset signal input terminal
Serial clock input terminal
8bit D–A converter output terminal
9
20 Analog power supply terminal
21
12
10
11
13
22
23
24
Ao12
VCC
VDD
GND
VrefL
VrefU1
VrefU2
CS2
CS1
CS0
Digital power supply terminal
Analog and digital common GND
D–A converter low level reference voltage input terminal
D–A converter high level reference voltage input terminal 1
D–A converter high level reference voltage input terminal 2
Chip select data input terminal 2
Chip select data input terminal 1
Chip select data input terminal 0
MITSUBISHI ELECTRIC
1997-5-28D.rev
( / 7)
2
ABSOLUTE MAXIMUM RATINGS
MITSUBISHI <Dig./Ana. INTERFACE>
M62398P,FP
8BIT 12CH I C BUS D–A CONVERTER WITH BUFFER AMPLIFIERS
2
Symbol
VCC
VDD
VrefU1,2
VinD
Pd
Topr
Tstg
Supply voltage
Supply voltage
D–A converter
upper reference voltage
Digital input voltage
Power dissipation
Operating temperature
Storage temperature
Parameter Conditions
Ratings
–0.3~13.5
–0.3~7.0
V
DD
–0.3~VDD+0.3
465(DIP) /421(FP)
–20~85
–40~125
ELECTRIC CHARACTERISTICS
< >
Symbol
VDD Supply voltage
IDD Supply current mA
IILK Input leak current
(VCC=13V,VDD=Vref U1,2=+5V±10%,GND=VrefL=0V,Ta=–20~85°C,unless otherwise noted)Digital part
Parameter Test conditions
MIN TYP MAX
Ratings
4.5 5.0 5.5
CLK=1MHz operation
IAO=0µA
VIN=0~VDD
–10 10
Unit
V
V
V
V
mW
°C
°C
Unit
V
1
µ A
VIL Input low voltage
VIH Input high voltage
0.8VDD
0.2VDD
V
V
Analog part< >(VCC=13V,VDD=VrefU1,2=+5V±10%,GND=VrefL=0V,Ta=–20~85°C,unless otherwise noted)
Symbol Parameter Test conditions
VCC
ICC
IrefU
VrefU
VrefL
VAO
IAO
SDL
Supply voltage
Supply current
D–A converter upper
reference voltage input current
D–A converter upper
reference voltage range
D–A converter lower
reference voltage range
Buffer amplifier
output voltage range
Buffer amplifier
output drive range
Differential nonlinearity error
CLK=1MHz Operation
IAO=0µA
VrefU=5V,VrefL=0V
Data condition:
at maximum current
The output dose not
necessarily be the values
within the reference
voltage setting range.
IAO=±500µA
IAO=±1.0mA
Upper side saturation
voltage=0.3V
Lower side saturation
voltage=0.2V
MIN
2.4VDD
3.5 V
GND 1.5 V
0.1 VCC-0.1 V
0.2
–2.5 2.5 mA
–1.0 1.0
Ratings
TYP MAX
13 V
2.0 4.0
1.2 2.5
VDD
VCC-0.2
Unit
mA
mA
V
LSB
VrefU=4.79V
SL
Nonlinearity error
VrefL=0.95V
–1.5 1.5
LSB
VCC=13V(36mV/LSB)
SZERO
Zero code error
without load (IAO=0)
–2.0 2.0
LSB
SFULL
SR
Full scale error
Output slew rate
–2.0 2.0
MITSUBISHI ELECTRIC
0.2
LSB
V/µs
1997-5-28D.rev
( / 7)
3