Mitsubishi M62230FP Datasheet

DESCRIPTION
PIN CONFIGURATION (TOP VIEW)
The M62230FP is a semiconductor circuit for LCD matrix regulator, which will generate the diveded-voltage to drive LCD matrix. By changing the connection of R pin(i.e.,Change the internal resistor ratio), M62230FP can support divided voltage ratio ranging from 1/5 bias to 1/13 bias. The high stability and any desired voltage levels is possible, since the variable voltage regulator for Vref is built-in.
FEATURES
•Adjustable type voltage divider. (The setting range of internal resistor is from 1/5 bias to 1/13 bias)
•5 resident buffer-Amp. (5 divided output)
•Low power dissipation(1.8 mA Typ.)
•Resident voltage-variable regulator for Vref.
MITSUBISHI (Dig./Ana. INTERFACE)
M62230FP
LCD MATRIX REGULATOR
R6 R5
R4 R3 R2 R1
REGOUT
REGIN
VIN3 VIN2
1 2 3 4 5 6 7 8 9
10
Outline 20P2N-A
VREF
20
VIN5
19
VCC
18
VO5
17
VO4
16
VO3
15
VO2
14
VO1
13 12
GND
11
VIN
APPLICATION
To drive LCD.
RECOMMEND OPERATING CONDITIONS (Ta=25°C)
Supply voltage range : GND-Vcc :(if V 1 > -1V, it is necessary to
support V IN)........ -30 to -10V
Recommend input voltage GND-VREF :VREF Vcc........ -30 to -6V
(To set Vcc, VREF, in order that both I 0-V2 I & I VCC-V5 I are larger than 1V)
BLOCK DIAGRAM
R1 R2 R3 R4
6
REGIN
VIN3
VIN2
GND
REGOUT
7
8
-1.38V
9
10
12
R R
R R
R
4R
R R
45
3
R
2
R5
R
1
R6
20
R
VREF
19
VIN5
11
VIN
13 14 15 16
VO1 VO2 VO3 VO4 VO5
( / 4 )
1
17
18
VCC
EXPLANATION OF TERMINALS
Pin No.
1 2 3 4 5 6 7 8 9
10
11
12 13 14 15 16 17 18 19 20
Symbol R6 R5 R4 R3 R2 R1 REGOUT REGIN VIN3 VIN2
VIN GND
VO1 VO2 VO3 VO4 VO5 VCC
VIN5 VREF
If the voltage of each pin can satisfy the following condition:
these pins will be used. Please refer to page. 4 to set the bias ratio.
Regulator output for VREF to use The inverting input pin of REG OP-Amp VIN3 Input VIN2 Input
VIN Power GND Pin
Divided-voltage output pin To set VCC & VREF, in order that 0 - V2 1V
To set VCC & VREF, in order that V5 - VCC 1V
VCC Power (-Power) VIN5 input Reference voltage input pin
MITSUBISHI (Dig./Ana. INTERFACE)
M62230FP
LCD MATRIX REGULATOR
Function
VO6 VO5 VO4 VO3 VO2 VO1
if V1 > -1.0V, it is necessary to support VIN if V1 < -1.0V, this pin connect to GND
( / 4 )
2
Loading...
+ 2 hidden pages