Page 1
EN – 1
ENGLISH
SA51
LCD
Projector
User Manual
MODEL LVP-SA51U
FRANÇAIS
DEUTSCH
ITALIANO
ESPAÑOL
Page 2
EN – 2
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended
to alert the user to the presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to constitute a risk of electric
shock.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION:
TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION
CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO
PREVENT BLADE EXPOSURE.
NOTE:
SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET MUST BE INSTALLED NEAR THE EQUIPMENT AND SHOULD BE EASILY ACCESSIBLE.
WARNING
Use the attached specified power supply cord. If you
use another power-supply cord, it may cause interference with radio and television reception.
Use the attached RGB cable, RS-232C cable with this
equipment so as to keep interference within the limit
of a FCC Class A device.
This apparatus must be grounded.
The projector automatically shuts off when the
lamp is used up in about 2,000 hours and cannot
be used until the lamp is replaced and the internal timer is reset. See page 22.
DO NOT LOOK DIRECTLY INTO THE LENS
WHEN PROJECTOR IS IN THE POWER ON
MODE.
When using the projector in Europe
COMPLIANCE NOTICE
This LCD - Video Projector complies with the requirements of the EC Directive 89/336/EEC “EMC
Directive” as amended by Directive 93/68/EEC and
73/23/EEC “Low Voltage Directive” as amended by
Directive 93/68/EEC.
The electro-magnetic susceptibility has been chosen
at a level that gains proper operation in residential
areas, on business and light industrial premises and
on small-scale enterprises, inside as well as outside
of the buildings. All places of operation are
characterised by their connection to the public low
voltage power supply system.
WARNING
Use the attached RGB cable or RS-232C cable with
this equipment so as to keep interference within the
limits of a EN55022 Class B and EN55013. Please
follow WARNINGS instructions.
Page 3
EN – 3
ENGLISH
Contents
Important safeguards ...........................................................................4
Overview ............................................................................................... 6
Using the remote control ......................................................................8
Battery installation ......................................................................................................... 8
Installation ............................................................................................9
Basic connections ............................................................................... 10
Projector + AV equipment............................................................................................. 10
Projector + DVD player or HDTV decoder ................................................................... 10
Projector + personal computer ...................................................................................... 11
Preparing the projector for operation ............................................... 12
To operate projector power ON.......................................................... 13
Menu operation .................................................................................. 15
Picture adjustment............................................................................. 18
Specification of RGB signals in each computer mode of the projector ....................... 20
Advanced feature for presentation .................................................... 21
Expand ........................................................................................................................... 21
Still ................................................................................................................................. 21
Lamp replacement ............................................................................. 22
Maintenance ....................................................................................... 23
Troubleshooting .................................................................................. 24
Indicators ............................................................................................ 25
Specifications ...................................................................................... 26
Kensington Lock ............................................................................................................ 26
Connectors ..................................................................................................................... 27
Dimensional drawings .................................................................................................. 27
What’s included in the box............................................................................................ 27
Replacement part .......................................................................................................... 27
Trademark, Registered trademark
Macintosh is registered trademark of Apple Computer Inc.
IBM and VGA are trademarks or registered trademarks of International Business Machines Corporation.
MicroSaver and Kensington are registered trademarks of Kensington Technology Group.
Other brand or product names are trademarks or registered trademarks of their respective holders.
Page 4
EN – 4
Important safeguards
Please read all these instructions regarding your LCD
projector and retain them for future reference. Follow
all warnings and instructions marked on the LCD projector.
1. Read instructions
All the safety and operating instructions should
be read before the appliance is operated.
2. Retain instructions
The safety and operating instructions should be
retained for future reference.
3. Warnings
All warnings on the appliance and in the operating instructions should be adhered to.
4. Instructions
All operating instructions must be followed.
5. Cleaning
Unplug this projector from the wall outlet before cleaning it. Do not use liquid aerosol cleaners. Use a damp soft cloth for cleaning.
6. Attachments and equipment
Never add any attachments and/or equipment
without the approval of the manufacturer as
such additions may result in the risk of fire, electric shock or other personal injury.
7. Water and moisture
Do not use this projector near water or in contact with water.
8. Accessories
Do not place this projector on an unstable cart,
stand, tripod, bracket or table. Use only with a
cart, stand, tripod bracket, or table recommended
by the manufacturer or sold with the projector.
Any mounting of the appliance should follow the
manufacturer's instructions and should use a
mounting accessory recommended by the manufacturer.
10. Power sources
This projector should be operated only from the
type of power source indicated on the marking
label. If you are not sure of the type of power,
please consult your appliance dealer or local
power company.
11. Power-cord protection
Power-supply cords should be routed so that they
are not likely to be walked on or pinched by items
placed upon or against them. Pay particular attention to cords at plugs, convenience receptacles,
and points where they exit from the appliance.
12. Overloading
Do not overload wall outlets and extension cords
as this can result in a fire or electric shock.
13. Objects and liquids
Never push objects of any kind through openings of this projector as they may touch dangerous voltage points or short-out parts that could
result in a fire or electric shock. Never spill liquid of any kind on the projector.
14. Servicing
Do not attempt to service this projector yourself.
Refer all servicing to qualified service personnel.
15. Damage requiring service
Unplug this projector from the wall outlet and
refer servicing to qualified service personnel under the following conditions:
(a) If the power-supply cord or plug is dam-
aged.
(b) If liquid has been spilled, or objects have
fallen into the projector.
(c) If the projector does not operate normally
after you follow the operating instructions.
Adjust only those controls that are covered
by the operating instructions. An improper
adjustment of other controls may result
in damage and may often require extensive work by a qualified technician to restore the projector to its normal operation.
(d) If the projector has been exposed to rain
or water.
(e) If the projector has been dropped or the
cabinet has been damaged.
(f) If the projector exhibits a distinct change
in performance - this indicates a need for
service.
16. Replacement parts
When replacement parts are required, be sure
that the service technician has used replacement
parts specified by the manufacturer or parts
having the same characteristics as the original
part. Unauthorized substitutions may result in
fire, electric shock or other hazards.
17. Safety check
Upon completion of any service or repair to this
projector, ask the service technician to perform
safety checks determining that the projector is
in a safe operating condition.
An appliance and cart combination should be
moved with care. Quick stops, excessive force and
uneven surfaces may cause the appliance and
cart combination to overturn.
9. Ventilation
Slots and openings in the cabinet are provided
for ventilation, ensuring reliable operation of the
projector and to protect it from overheating. Do
not block these openings or allow them to be
blocked by placing the projector on a bed, sofa,
rug, or bookcase. Ensure that there is adequate
ventilation and that the manufacturer's instructions have been adhered to.
Page 5
EN – 5
ENGLISH
WARNING:
Unplug immediately if there is
something wrong with your projector.
Do not operate if smoke, strange noise or odor comes
out of your projector. It might cause fire or electric
shock. In this case, unplug immediately and contact
your dealer.
Never remove the cabinet.
This projector contains high voltage circuitry. An
inadvertent contact may result in an electric shock.
Except as specifically explained in the Owner's
Guide, do not attempt to service this product
yourself. Please contact your dealer when you want
to fix, adjust or inspect the projector.
Do not modify this equipment.
It can lead to fire or electric shock.
If you break or drop the cabinet.
Do not keep using this equipment if you break or
drop it. Unplug the projector and contact your dealer
for inspection. It may lead to fire if you keep using
the equipment.
Do not face the projector lens to the
sun.
It can lead to fire.
Use correct voltage.
If you use incorrect voltage, it can lead to fire.
Do not look into the lens when it is
operating.
It may hurt your eyes.Never let children look into
the lens when it is on.
Do not turn off the main power
abruptly or unplug the projector
during operation.
It can lead to lamp breakage, fire, electric shock or
other trouble. It is best to wait for the fan to turn off
before turning main power off.
Do not place the projector on uneven
surface.
Place the projection on a leveled and stable surface
only. Please do not place equipment on unstable
surfaces.
Do not touch Air outlet grill and
Bottom plate which becomes hot.
Do not touch them or put other equipment in front of
Air outlet grill. The heated Air outlet grill and Bottom plate may cause injury or damage to other equipment. Also, do not set the projector on the desk which
is easily affected by heat.
Clean the air-filter once a month.
Clean the air-filter frequently. If the filter or ventilation slots become clogged with dirt or dust, the temperature inside of the projector may rise and cause
some troubles, such as damage of inside parts, and
shortening the life of panel.
Place of installation
For safety’s sake, refrain from setting the projector at
any place subjected to high temperature and high
humidity. Please maintain an operating temperature,
humidity, and altitude as specified below.
• Operating temperature: between +41°F (+5°C) and
+95°F (+35°C)
• Operating humidity: between 30 and 90%
• Never put any heat-producing device under the pro-
jector so that the projector does not overheat.
• Do not attach the projector to a place that is unstable or subject to vibration.
• Do not install the projector near any equipment that
produces a strong magnetic field. Also refrain from
installing near the projector any cable carrying a
large current.
• Place the projector on a solid, vibration free surface: otherwise it may fall, causing serious injury
to a child or adult, and serious damage to the product.
• Do not stand the projector: it may fall, causing serious injury and damage to the projector.
• Place the projector within a slope of ±15˚. Slanting
the projector more than ±15˚ may cause trouble or
explosion of the lamp.
• Do not place the projector near air-conditioning unit
or heater to avoid hot air to the exhaust and ventilation hole of the projector.
COMPLIANCE NOTICE OF FCC
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his own expense.
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus as set
out in the interference-causing equipment standard entitled “Digital Apparatus”, ICES-003 of the Department of
Communications.
Changes or modifications not expressly approved by Mitsubishi could void the user's authority to operate this equipment.
COMPLIANCE NOTICE OF INDUSTRY CANADA
This Class A digital apparatus complies with Canadian ICES-003.
Page 6
EN – 6
Overview
1
2345
89101112
6
7
POWER
LAMP
VOLUME
TEMP
VIDEO
ENTER
MUTE
MENU
SOURCE
COMPUTER
AUTO POSITION
56910
314
11
12
13
8
7
2
1
2
3
45678
O
I
S-VIDEO
VIDEO
AUDIO L
(MONO)
AUDIO R
AC IN
MAIN
VIDEO IN
COMPUTER INCOMPUTER OUT
RS-232C
Control panel
Terminal board
1 Air inlet grill (Front)
2 Front height adjuster button
3 Air inlet grill (Side)
4 Terminal board
5 Speaker
6 Remote control sensor (Front)
7 Zoom ring
8 Focus ring
9 Control panel
10 Lens
11 Kensington Security Lock Standard connec-
tor
12 Remote control sensor (Rear)
13 Air outlet grill
1 LAMP indicator
2 TEMP (temperature) indicator
3 + , – (VOLUME) button
4 VIDEO button
5 MENU button
6 ENTER button
7 Direction buttons
8 MUTE (Audio/Video) button
9 AUTO POSITION button
10 COMPUTER button
11
Power button
12 Power indicator
1 Ground terminal
2 Power jack
3 Main power
I : ON
O : OFF
4 Video/audio input terminals
5 Reset button
6 COMPUTER IN terminal (Mini D-SUB 15P)
7 COMPUTER OUT terminal (Mini D-SUB 15P)
8 RS-232C (Mini DIN 8P) terminal
Page 7
EN – 7
ENGLISH
Bottom side
3
2
1
1 Adjustment foot (right and left)
2 Lamp cover
3 Adjustment foot (up and down)
Caution:
Do not replace the lamp right after using the projector. The
lamp will be very hot.
1
2
3
4
5
6
7
8
9
10
11
EXPAND
ENTER
MENU
COMPUTER
POWER
VIDEO
V
C
AUTO
POSITION
STILL
MUTE
VOLUME
Remote control
1 COMPUTER button
2 MENU button
3 AUTO POSITION button
4 STILL button
5 + , – (VOLUME) buttons
6 MUTE (Audio/Video) button
7 EXPAND button
8 ENTER button
9 Direction buttons
10 POWER button
11
VIDEO button
Page 8
EN – 8
Battery installation
Use two AAA size batteries.
1. Remove the back cover of the remote control by pushing the battery compartment door in the direction of the
arrow.
2. Load the batteries making sure that they are positioned correctly (+ to +, and - to -).
• Load the batteries from - spring side, and make sure to set them tightly.
3. Replace the back cover.
Important:
• Do not combine a new battery with an old one.
• Load batteries in the correct position.
• Do not heat, take apart, or throw batteries into fire.
• Do not try to recharge batteries. Do not use rechargeable batteries.
• If the solution of batteries comes in contact with your skin or clothes, rinse with water. If the solution comes
in contact with your eyes, rinse them with water and then consult your doctor.
Operation area
The range for operation is about 10 m (about 32 feet) when the remote control points to the projector. The distance to the screen back to the projector must be less than 6 m (about 20 feet). Depending on the type of the
screen, the distance will be different.
Important:
Avoid the direct sunlight or fluorescent light to the remote control sensor. Also keep the distance of more than 2 m
(6.5") between the remote control sensor and fluorescent lamp on the remote control may not work correctly.
20˚
15˚
20˚
15˚
30˚30˚
12 3
Using the remote control
Page 9
´ EN – 9
ENGLISH
Installation
Orientation of the projector
Picture size can be set by changing the distance between the screen and the projector.
Front projection
To find the approximate distance between the projector and screen:
Multiply the width of the screen
X 1.9 (min.) , Multiply the width of the
screen X 2.4 (max.).
• Refer to the chart for recommended
distances in maximum zoom and
minimum zoom.
Ceiling mount, Rear projection
Ask a specialist for installation. For more details,
consult your dealer.
Caution:
• Placing the projector on a carpet reduces ventilation from the fan at the bottom and might cause
problems. Place a hard board or similar item
under the projector to facilitate ventilation of the
unit.
• Place the projector more than 50 cm (20 inch)
from the wall to prevent blocking the intake,
exhaust slots and ventilation of this projector
because hot air comes out of it.
• Do not use the projector under the following
circumstances, which may cause fire or electric
shock.
• in a dusty or humid place
• while the projector is lying sideways or upside
down
• near a heater
• in a kitchen or oily, smoky or damp place
• in direct sunlight
• with high temperature, such as a closed car
• where the temperature is lower than 41°F or
higher than 95°F
Important:
• Do not add stress on the lens, as this may cause
damage.
L
(between the screen and
the head of the projector)
Screen
H
Screen
Width
Height
A
A=B
B
• The above numbers are approximate, and may be slightly different from the actual measurements.
Diagonal size
(inch)
40 "
60 "
80 "
100 "
120 "
140 "
160 "
180 "
200 "
250 "
300 "
Height inches
(inch)
24 "
36 "
48 "
60 "
72 "
84 "
96 "
108 "
120 "
150 "
180 "
Width feet
(inch)
32 "
48 "
64 "
80 "
96 "
112 "
128 "
144 "
160 "
200 "
240 "
Screen
Distance from screen (L) / (approximate)
Maximum
zoom (WIDE)
(cm)
6.1
9.1
12.2
15.2
18.3
21.3
24.4
27.4
30.5
38.1
45.7
(inch)
2.4 "
3.6 "
4.8 "
6.0"
7.2 "
8.4 "
9.6 "
10.8 "
12.0 "
15.0 "
18.0 "
Minimum
zoom (TELE)
Height projected
image (H)
(cm)
155
235
315
394
474
554
634
713
793
993
1192
(cm)
188
284
380
476
572
668
765
861
957
1197
1437
(inch)
61 "
93 "
124 "
155 "
187 "
218 "
250 "
281 "
312 "
391 "
469 "
(inch)
74 "
112 "
150 "
187 "
225 "
263 "
301 "
339 "
377 "
471 "
566 "
Page 10
EN – 10
Basic connections
This projector can be connected to equipment such as PC, VCRs, video cameras and DVD players.
Important:
• Make sure that your equipment is turned off before connection.
• Plug in firmly and unplug by holding the plug, not by pulling the AC power cord.
• If connected units are set too close to one another, the image may be affected.
• Refer to the user manual of each component for details of connections.
Projector + AV equipment
Important:
• Match the color of video and audio plugs on the AV cable with the connections.
• S-video signals take priority over video signals. If you input both S-video signals and normal video signals at
the same time, the normal video input automatically is inhibited.
O
I
S-VIDEO
VIDEO
AUDIO L
(MONO)
AUDIO R
AC IN
MAIN
VIDEO IN
COMPUTER INCOMPUTER OUT
RS-232C
Connect either one of these.
to S-video input
to S-video output
to video input
to audio input
to video output
to audio output
VCR etc.
• Speaker output is mono.
• Select AUDIO MODE 2 to hear and to sound for the VIDEO. (Refer to page 16).
• When connecting audio output of equipment which audio output is mono, connect to audio input L terminal.
Projector + DVD player or HDTV decoder
Some DVD players have output terminal for 3 line fitting (Y, CB, CR). When connecting them to the projector,
connect to COMPUTER IN of the projector.
DVD player generally has SDTV system component video output (Y, CB, CR) terminals. HDTV decoder has HDTV
system component video output (Y, PB, PR) terminals. When connecting the projector with DVD player or HDTV
decoder, the signal cuircuit automaticaly applied to either of them. In this case, the COMPUTER INPUT in the
SIGNAL menu becomes [Y, CB, CR/Y, PB, PR].
O
I
S-VIDEO
VIDEO
AUDIO L
(MONO)
AUDIO R
AC IN
MAIN
VIDEO IN
COMPUTER INCOMPUTER OUT
RS-232C
B G R
C
B(PB
)Y CR(PR)
HD/CS VD
DVD player or HDTV decoder
No connection
BNC - RCA connector
(optional)
Mini D-SUB 15 pin-BNC
conversion cable (optional)
to AUDIO IN
to AUDIO OUT
AUDIO cable
to COMPUTER
IN
• Y, PB, PR is an example of the terminal names for a HDTV decoder.
• The terminal name is different depending on the connected equipment.
• Use mini D-SUB 15 pin-BNC conversion cable for connection.
• Some DVD players may not project the image correctly.
• When connecting with HDTV equipment which has R, G, B output, set RGB for the COMPUTER INPUT in
the SIGNAL setting menu.
• Change the setting in the SIGNAL menu, when 525p signal is inputted. (Refer to page 20).
Page 11
´ EN – 11
ENGLISH
AUDIO OUT
MONITOR OUTPUT
to COMPUTER IN
to AUDIO IN
to monitor
port
to COMPUTER
OUT
to PC audio
output
PC audio cable (option)
When outputting to both a PC monitor and the projector.
RGB cable for PC
RGB cable for PC (option)
computer
O
I
S-VIDEO
VIDEO
AUDIO L
(MONO)
AUDIO R
AC IN
MAIN
VIDEO IN
COMPUTER INCOMPUTER OUT
RS-232C
Projector + Personal computer
Important:
• Connectors or analog RGB output adapters may be necessary depending on the PC connected to this projector.
Please contact your dealer.
• The audio input for this projector is a stereo pin jack. (Speaker output is mono.) Please check the available
cable for the audio input terminal of the PC. Some personal computer may not have the audio output terminal.
• Select AUDIO MODE 1 to hear and to sound for the COMPUTER. (Refer to page 16).
• When connecting audio output of a personal computer which audio output is mono, connect to the audio input
L terminal.
For using Macintosh
• A monitor output adapter is necessary for a Macintosh if it has no video port. Please contact your dealer.
• A MAC adapter for RGB cable may be necessary depending on the personal computer connected to this projec-
tor. Please contact your dealer.
Page 12
EN – 12
Adjustment foot
screen
Preparing the projector for operation
Getting ready for projection
1. Connect the power cord provided to the projector.
2. Connect the power cord to the wall power outlet.
3. Remove the lens cap.
Warning:
• Do not look directly into the lens when projector is
“ON”.
• The lens cap is for protecting the lens. If you leave
the power on with the cap on, the cap may be warped.
Please remove the lens cap when you turn the power
on.
• This projector is equipped with the power cords for
both U.S. and Europe. Use the appropriate power
cord for your country.
• A three-pin grounding type power plug is used with
the projector. Do not remove the grounding pin on
the power plug. If you are unable to insert the plug
into the outlet, contact your electrician to replace
your A/C outlet.
• The supplied power cord for U.S. is used for 120V
only. Never connect to any outlet or power supply
having a different voltage or frequency. If you
connect to the power supply having a different
voltage, please use the appropriate power cord.
• Use 100-240V AC 50/60Hz correct voltage otherwise it may lead to fire or electric shock.
• Do not place any objects on the power cord, and keep
the projector away from heat sources to avoid damaging the power cord. A damaged power cord can
cause fire or electric shock.
• Do not modify or alter the power cord otherwise it
may cause fire or electric shock.
Contact your dealer if the cord is damaged.
Caution:
• Plug in firmly and unplug by holding the plug, not
by pulling the cable out.
• Do not plug in or out with wet hands. It may cause
an electric shock.
Adjusting the angle of projection
For the best result, project onto a flat screen with a 90
degree angle to the floor. If necessary, tilt the projector
by adjusting two foot adjustments on the bottom of the
projector.
1. Lift the projector to the appropriate angle.
2. Press the Front height adjuster button, this will allow the adjustment foot (up and down) to slide out
to the position.
3. Release the Front height adjuster button to lock the
feet in that position.
After using the projector
4. Return the adjustment foot (up and down) into the
projector by pressing the Front height adjuster button.
When the left and right angles are different
Adjust the angles with adjustment feet (right and left),
which are on the bottom of the projector.
Important:
• Screen on a flat wall with a 90˚ angle to the floor.
• Align projector to produce a full screen display as
illustrated on page 9.
• The distance from the projector to the screen must
be compatible with screen size chart on page 9.
Note the distance from the screen chart.
A
djustment foot
(up and down)
Front height
adjuster button
Adjustment foot
(right and left)
Page 13
´ EN – 13
ENGLISH
To operate projector power ON
• When the lamp indicator is blinking red, the the
lamp should be replaced. Replace the lamp. See
pages 22 and 25.
• The picture might not be of optimum performance
in extreme hot or cold conditions. (The projector is
not malfunctioning.)
4. Select the desired external input source by using
the COMPUTER or VIDEO button.
• The COMPUTER or VIDEO buttons do not work
when MENU is displayed.
• The projector automatically selects the appropriate
signal format. The selected signal format is displayed on the screen.
• When selecting the COMPUTER input, the image
may flicker. Press the $ or % button to adjust the
image.
5. Adjust the image size with the zoom ring by turn-
ing it.
6. Adjust the focus with the focus ring by turning it.
1. Turn on the equipment connected to the projector.
2. Put the projector into standby mode by pressing the
main power switch. The POWER indicator lights up
red.
• The POWER indicator blinks red for 2, 3
seconds after the power switch ON. In this
time, the buttons will not work.
3. Turn the projector on by pressing the POWER button.
The light source lamp starts warming up, eventually turning completely on.
• When the light source lamp does not light up,
wait until the LAMP indicator is turned off, then
press the POWER button again.
• If the main power switch to the unit is turned
off within two minutes of turning off the light
source lamp, power will not be applied to the
lamp for one minute when the next time the
main unit power switch is turned on. When
this happens, the indicator lamp will blink for
one minute.
Condition
Indicator
LAMP POWER
Stand-by
-
Red
When light source lamp is on
Green
Green
Light source lamp held off temporarily
Red
-
Important:
• A darkened image may be seen right after pressing
the POWER button due to warming up of this projector. While warming up, no other commands can
be accepted.
EXPAND
ENTER
MENU
COMPUTER
POWER
VIDEO
V
C
AUTO
POSITION
STILL
MUTE
VOLUME
O
I
S-VIDEO
VIDEO
AUDIO L
(MONO)
AUDIO R
AC IN
MAIN
VIDEO IN
COMPUTER INCOMPUTER OUT
RS-232C
2 • 9
MUTE button
STILL button
4
4
3 • 7 •
8
POWER
LAMP
VOLUME
TEMP
VIDEO
ENTER
MUTE
MENU
SOURCE
COMPUTER
AUTO POSITION
AUTO POSITION
button
3 • 7 • 8 4
MUTE button
AUTO POSITION button
wide
zoom ring
tele
far
near
focus ring
Page 14
EN – 14
30
To operate projector power ON (Continue)
Turning off the projector
7. Press the POWER button.
The message “POWER OFF? YES : PRESS AGAIN”
appears on the screen.
• To exit from this mode, press any button except
POWER button.
8. Press the POWER button again.
The light source lamp will be turned off.
Pressing the POWER button second time will shut
off the light source lamp, but the exhaust fan continues to operate for 60 seconds to cool down the
light source lamp and LCD panels. In this time, the
lamp indicator will be turned off.
9. Turn off the main power switch. When turning off
the main switch, the POWER indicator turns off.
• In cases where the main power switch is accidentally turned off when either the intake/exhaust
fan or the power source lamp is in operation, allow
the unit to cool down for 10 minutes with the
power turned off. Repeat step 3 when turning on
the power source lamp. If the lamp does not turn
on immediately, repeat this step two or three
times. Replace the lamp if it should still fail to
turn on.
AUTO POSITION button
When the source is selected to COMPUTER and the
image is not in the right place, follow as shown below.
1. Set screen to the brightest display as possible
(e.g., full-screen display of the “Trash” window).
2. If the screen saver is running, turn off the screen saver.
3. Press the AUTO POSITION button.
• If the image is still not in the right place, adjust
the image position by using the SIGNAL menu.
The sound from the speaker
The sound from the speaker is mono.
• When inputting mono sound, connect to AUDIO L
terminal.
• The output sound is selected by changing the
setting of AUDIO MODE in the FEATURE menu.
See page 16 for details.
The volume from the speaker
Press the volume + or – button to change the volume
from the speaker.
The volume control bar will appear on the screen.
• The volume control bar will disappear about 4
seconds after releasing the volume buttons.
• The volume buttons do not work when MENU
selection bar or MENU is displayed.
AV mute
Image and audio are temporarily muted by pressing
the MUTE button. To restore the image and audio to
the normal mode, press the MUTE button again.
• To prevent the damage of the LCD, the image and
audio will be restored automatically to the normal
mode, 10 minutes after setting the AV mute mode.
Caution:
• When you have finished using this equipment, wait
60 seconds for the exhaust fans to stop. Then turn off
the main switch and unplug the power cable from the
wall outlet, for safety purposes.
• After the lamp is turned off, the lamp cannot be
switched on again for 60 seconds as a precautionary measure. If you wish to turn on the projector
again, wait until the indicator is off then press the
POWER button.
• The exhaust fan rotates faster when the temperature around the projector rises.
• When the temperature around the projector becomes
too high, the sign “TEMP!!” blinks red on the screen.
If the temperature stays too high, the lamp will be
shut off automatically .
The projector automatically shuts off when the
lamp is used up in about 2,000 hours and cannot
be used until the lamp is replaced and the internal timer is reset. See page 22.
Page 15
EN – 15
ENGLISH
Basic operation
Several settings can be adjusted using Menu.
EXAMPLE: Auto power off time setting
1. Press the MENU button.
2. Press the $ or % button to select the INSTALLA-
TION menu.
3. Press the ENTER button (or } button).
4. Press the { or } button to select AUTO POWER
OFF.
5. Press the $ or % button to adjust auto power off
time.
6. Exit the menu system by pressing the MENU but-
ton several times.
• If the menu operation is not working, press the
RESET button on the terminal board using a suitable sharp object, push gently.
• The settings with 2 mark, you should press the
ENTER button after selecting.
Menu operation
Opt
IMAGE
XGA60
Opt
INSTALLATION
XGA60
Opt
INSTALLATION
AUTO POWER
ON
OFF
OFF
AUTO POWER
OFF
OFF
XGA60
IMAGE REVERSE
AUTO POWER
ON
OFF
OFF
AUTO POWER
OFF
OFF
IMAGE REVERSE
AUTO POWER
ON
OFF
OFF
AUTO POWER
OFF
30 min
IMAGE REVERSE
IMAGE CONTRAST ± 30
BRIGHTNESS ± 30
1
COLOR MATRIX
SHARPNESS ± 10
TINT ± 10
COLOR ± 10
RED ± 30
CYAN ± 30
GREEN ± 30
YELLOW ± 30
BLUE ± 30
MAGENTA
(Displays only when the source is selected to VIDEO)
(Displays only when the source is selected to VIDEO)
(AUTO : When the source is selected to COMPUTER)
± 30
CONTRAST R ± 30
CONTRAST B ± 30
BRIGHTNESS R ± 30
BRIGHTNESS B ± 30
EXPAND MODE 1 - 2
RESET ALL OK
1=Upper left, 2=Lower right
INSTALLATION
IMAGE REVERSE OFF, MIRROR, INVERT, MIRROR INVERT
AUTO POWER ON ON, OFF
AUTO POWER OFF
1 - 3
ON, OFF
FEATURES MENU POSITION
OFF, 5, 10, 15, 30, 60 min
VIDEO SIGNAL
AUDIO MODE
ANAMORPHIC
AUTO, NTSC, PAL, SECAM, 4.43NTSC, PAL-M, PAL-N, PAL-60
LANGUAGE
SIGNAL MEMORY CALL AUTO, USER1, USER2
HORIZ.POSITION 0 - 999
VERT.POSITION 0 - 999
FINE SYNC. 0 - 39
TRACKING
USER
0 - 9999
CLAMP POSITION 0 - +63
CLAMP WIDTH 0 - +63
HORIZ. PIXELS 0 - 9999
VERT LINES 0 - 9999
PLL
AUTO, 0 - 7
SHUTTER (L)
0 - 299
SHUTTER (U)
0 - 299
SHUTTER (RS)
0 - 398
SHUTTER (LS)
0 - 398
VERT. SYNC
AUTO, ON, OFF
2
USER
USER
OFF
STANDARD
HIGH
LOW
COLOR TEMP.
USER
MEMORIZE
*
*
*
HOLD AUTO
USER1, USER2
DELETE
USER1, USER2
DEFAULT
ON
BEGIN -1 - -99
END 1 - 99
OFF
COMPUTER INPUT RGB, YCBCR / YPBP
R
*
*
*
*
* : Setting range is different
according to the type of
the signal.
, English, Español, Deutsch, Français, Italiano,
3
Page 16
EN – 16
Opt
INSTALLATION
AUTO POWER
ON
OFF
OFF
AUTO POWER
OFF
OFF
XGA60
IMAGE REVERSE
A
Ë
?
Opt
A
A
MENU POSITION
FEATURE
VIDEO SIGNAL AUTO
LANGUAGE English
RESET ALL OK
ANAMORPHIC OFF
XGA60
EXPAND MODE 1.
AUDIO MODE
1.
2
1 IMAGE
CONTRAST ........ Adjusts the picture contrast. The contrast becomes higher
as the number increases.
BRIGHTNESS .... Adjusts image brightness. The image becomes brighter as
the number increases.
COLOR MATRIX. ......
Adjusts color balance in each color of the image. See page
18.
COLOR TEMP... . Adjusts color temperature. See page 18.
SHARPNESS ...... Adjusts the picture sharpness. The sharpness becomes
sharper as the number increases.
TINT .................... Adjusts the color balance of the image. The color balance
of the image shifts green as the number increases and
shifts to purple as the number decreases (displays only when the source is selected to
VIDEO).
• When the TV50 (PAL, SECAM) signal is inputted, you cannot adjust the TINT.
COLOR ................ Adjusts the color intensity of the image (displays only when the source is selected to VIDEO).
2 INSTALLATION
AUTO POWER ON .....
To select whether to boot up automatically when the power is
turned on external to the projector. In this case, the main
power switch of the projector has to be ON. Set this when the
projector is hanging on the ceiling.
• The projector is in stand-by mode when the lamp is not
on. In this case, use the remote control to turn on the
lamp.
AUTO POWER OFF ..
Use to select the length of time before projector switches to stand-by when there is no input
signal selected source.
IMAGE REVERSE
Use to reverse or invert the projected image. MIRROR is used to rear projection. MIRROR
INVERT is for ceiling-mount.
3 FEATURES
MENU POSITION .
Use to select the position where the menu is displayed,
(upper left) or (lower right).
EXPAND MODE Selects the mode of enlarging screen. See page 21.
AUDIO MODE .......
Select 1 (COMPUTER mode) to output the sound which is
inputted to audio input terminal only when the source is
selected to COMPUTER. Select 2 (VIDEO mode) to output
the sound which is inputted to audio input terminal only
when the source is selected to VIDEO. Select 3
(PARMANENT mode) to output the sound which is
inputted to audio input terminal at all time.
VIDEO SIGNAL . When AUTO is set, the appropriate video format is
automatically selected according to the input signal. If the image does not appear correctly,
select the desired video format manually.
ANAMORPHIC... Set ON when displaying DVD discs which are recorded in letter boxed images.
LANGUAGE ....... Use to select the language for the projector display such as menu. ( / English / Español
/ Deutsch / Français / Italiano / )
RESET ALL ........ Use to reset the MENU setting (except LANGUAGE).
Opt
CONTRAST
IMAGE
0
BRIGHTNESS 0
COLOR TEMP. STANDARD
TINT 0
COLOR 0
SHARPNESS 0
XGA60
COLOR MATRIX
USER
Menu operation (continued)
Page 17
EN – 17
ENGLISH
4 SIGNAL
MEMORY CALL ........
Use to select AUTO, USER 1 or USER 2. See below.
HORIZ. POSITION ....
Use to adjust the horizontal position of the image.
VERT. POSITION .....
Use to adjust the vertical position of the image.
FINE SYNC. ....... Use to synchronize the projector with PC input signals so
that the image is not blurred.
TRACKING ......... Use to avoid image noise such as wide stripes.
COMPUTER INPUT ....
The unit adjusts itself automatically when connected to a
DVD player with component video output (Y, CB, CR ) or
equipment with HDTV SIGNAL output (Y, PB, PR). In the
case the projector is connected to equipment that includes
RGB output terminal, adjust to RGB mode.
HOLD .................. Adjusts the image when flagging occurs near the top of the
screen.
5 SIGNAL - USER (Normally, there is no need for adjustments.)
CLAMP POSITION/
CLAMP WIDTH .........
If you use something similar, the brighter colors of the
projected image may become blurred. In this case, adjust
CLAMP POSITION or CLAMP WIDTH.
HORIZ.PIXELS .. Use to adjust the width of the image. The image size
grows wider as the number increases. (Adjust to the
horizontal pixels of the input signal for normal setting.)
VERT.LINES ...... Use to adjust the height of the image. The image size
grows higher as the number increases. (Adjust to the
vertical lines of the input signal for normal setting.)
PLL ...................... Use to adjust the image when skewed on top. Select
AUTO for normal setting.
VERT.SYNC. ...... Use to adjust the image when its motion does not run
smoothly. Select AUTO for normal setting.
SHUTTER(U) ..... Use to adjust the image when the noise etc. appears on top part of image.
SHUTTER(L) ...... Use to adjust the image when the noise etc. appears on bottom part of image.
SHUTTER(LS) .... Use to adjust the image when the noise etc. appears on left side of image.
SHUTTER(RS) ... Use to adjust the image when the noise etc. appears on right side of image.
User memory for signal setting
This projector can memorize the maximum of 2 signal menu settings.
Memorizing the setting
1. Select MEMORIZE in the SIGNAL menu, and press the ENTER button.
2. Press the $ or % button to select the memory which you wish to record (USER 1 or USER 2).
3. Press the ENTER button.
Initialite the setting which has been changed (Default)
Select RESET in the SIGNAL menu, and press the ENTER button.
• When initializing, selection buttons will not work for about 2 - 18 seconds.
Select the user setting
Select MEMORY CALL in SIGNAL menu, and press the $ or % button to select the memory (USER 1 or USER 2).
Reset the recorded setting
1. Select DELETE in the SIGNAL menu, and press the ENTER button.
2. Press the $ or % button to select the memory which you wish to reset (USER 1 or USER 2).
3. Press the ENTER button.
The recorded setting will be reset.
?
CLAMP POSITION
SIGNAL-USER
0
CLAMP WIDTH 0
HORIZ. PIXELS 0
PLL AUTO
SHUTTER(RS) 0
VERT. LINES 0
VERT. SYNC. AUTO
SHUTTER(LS) 0
SHUTTER(L) 0
SHUTTER(U) 0
R G B
R G B
A
U
Opt
MEMORY CALL
SIGNAL
AUTO
HORIZ. POSITION 0
VERT. POSITION 0
TRACKING 0
COMPUTER INPUT RGB
FINE SYNC. 0
HOLD AUTO
USER MEMORIZE DELETE DEFAULT
XGA60
Page 18
EN – 18
Adjusting the image
You can adjust the picture by using the IMAGE menu.
To control the level of white-to-black in the image :
Adjust CONTRAST in IMAGE menu. Press the %
button to increase the contrast and the $ button to
reduce it.
To control the light level of the image :
Adjust BRIGHTNESS in IMAGE menu. Press the %
button to lighten the image and the $ button to
darken the image.
To adjust the detail and clarity of the image :
Adjust SHARPNESS in IMAGE menu. Press the %
button to make the picture seem sharper and the $
button to make it softer.
To determine the intensity of the color :
Adjust COLOR in IMAGE menu. Press the %
button to increase the amount of color in the image
and the $ button to decrease it.
To adjust the red-green color balance of the image :
Adjust TINT in IMAGE menu. Press the % button
to increase the amount of green in the image and the
$ button to increase the amount of red in the image.
Color matrix
This feature adjusts the color balance in each color of
RGB (Red, Green, Blue), and their neutral colors
(yellow, cyan, magenta) by using Color correction
adjustment. Use Color correct adjustment when
enphasizing a specific color, or when only a certain
color balance is not correctly adjusted.
1. Select COLOR MATRIX in IMAGE menu.
2. Press the ENTER button.
3. Press the $ or % button to select USER }.
4. Press the { or } button to select the desired color.
5. Press the $ or % button to adjust the color balance
of the color.
6. Repeat steps 4 and 5 for more adjustments.
Picture adjustment
CONTRAST R
COLOR TEMP.-USER
0
CONTRAST B 0
BRIGHTNESS R 0
BRIGHTNESS B 0
Opt
CONTRAST
IMAGE
0
BRIGHTNESS 0
COLOR TEMP. STANDARD
TINT 0
COLOR 0
SHARPNESS 0
XGA60
COLOR MATRIX
USER
About color temperature
There are different kinds of white color. Color temperature is
a way to show the differences. The white, which temperature
is low, becomes reddish white. When the color temperature is
higher, the white becomes more bluish. This projector sets
this color temperature by changing the numbers of contrast
blue and red.
To set the color temperature high:
Set the contrast B (Blue) number high, and the contrast R
(Red) number low.
To set the color temperature low:
Set the contrast B (Blue) number low, and the contrast R
(Red) number high.
7. Exit the menu system by pressing the MENU button several times.
• When using the setting which has been already
prepared, select desired position 1, 2 or 3 in step 3.
When the source is selected to VIDEO, 1 will be
selected automatically. When the source is selected
to COMPUTER, 3 will be selected automatically.
• When not using Color matrix adjustment, select
OFF in step 3.
Color temperature
1. Select COLOR TEMP in IMAGE menu.
2. Press the $ or % button to select USER 2.
3. Press the ENTER button.
4. Press the { or } button to select the desired item.
5. Press the $ or % button to adjust the item.
6. Repeat steps 4 and 5 for more adjustments.
7. Exit the menu system by pressing the MENU button several times.
COLOR MATRIX
RED 0
0
0
0
0
GREEN
BLUE
YELLOW
CYAN
1 2 3 USER OFF
MAGENTA 0
Page 19
EN – 19
ENGLISH
Adjustment from personal computer
Although this projector sets proper signal systems
automatically for the image signal from personal
computers, it cannot be applied to some of personal
computers. In this case, press the AUTO POSITION
button. If the images are still not projected correctly,
use the MENU display to adjust the projected images.
Image moved to right or left :
Adjust HORIZ. POSITION in SIGNAL menu. Press
the % button to move the image to left. Press the $
button to move the image to right.
Image moved to up or down :
Adjust VERT. POSITION in SIGNAL menu. Press
the % button to move the image to upward. Press
the $ button to move the image to down.
Image flickers / Image is out of focus :
Adjust FINE SYNC. in SIGNAL menu.
Wide stripes appear :
Adjust CLAMP POSITION or CLAMP WIDTH of
each menu in SIGNAL - USER menu.
Noise appears on the right or left side of image :
Adjust HORIZ. PIXELS of the menu in SIGNAL USER menu.
R G B
R G B
A
U
Opt
MEMORY CALL
SIGNAL
AUTO
HORIZ. POSITION 0
VERT. POSITION 0
TRACKING 0
COMPUTER INPUT RGB
FINE SYNC. 0
HOLD AUTO
USER MEMORIZE DELETE DEFAULT
XGA60
?
CLAMP POSITION
SIGNAL-USER
0
CLAMP WIDTH 0
HORIZ. PIXELS 0
PLL AUTO
SHUTTER(RS) 0
VERT. LINES 0
VERT. SYNC. AUTO
SHUTTER(LS) 0
SHUTTER(L) 0
SHUTTER(U) 0
Noise etc. appears on top or bottom part of image :
Adjust SHUTTER (U), SHUTTER (L) or VERT.
LINES of the menu in SIGNAL - USER menu.
Noise etc. appears on left or right side of image :
Adjust SHUTTER (LS) or SHUTTER (RS) of the
menu in SIGNAL - USER menu.
Top part of image curves :
Change the setting of HOLD in SIGNAL menu or
PLL in SIGNAL - USER menu.
HOLD ...Select ON, and adjust BEGIN or END
for image which top part is the least
curved.
PLL ....... Select 0 - 7 for an image in which top
part is the least curved. Select AUTO for
normal setting.
Image does not move naturally :
Adjust VERT. SYNC. of the menu in SIGNAL USER menu. Select AUTO for normal setting.
curved. Select AUTO for normal setting.
• Do not change each menu setting in USER
menu for normal setting.
Simple adjustment method
1. Select HORIZ. POSITION in SIGNAL menu.
2. Press the$ or % button to adjust the horizontal
start position (the left side of image).
3. Select TRACKING in SIGNAL menu.
4. Press the$ or % button to adjust the horizontal
end position (the right side of image).
5. Repeat steps 1 to 4 for fine adjustment.
6. Select VERT. POSITION in SIGNAL menu.
7. Press the$ or % button to adjust the vertical
start position (the top end of image).
Page 20
EN – 20
Specification of RGB signals in each computer mode of the projector
• When the EXPAND MODE of FEATURE menu is
set to real screen display, by pressing the EXPAND
button on the remote control, it will switch to the
screen displaying the picture as its original size (real
screen display). In the real screen display, pictures
will be black-framed when picture resolution is lower
than 800 x 600.
Important:
• Some computers may not be compatible with the
projector.
• The projector's maximum resolution is 800 x 600 pix-
els. It may not display correctly for the pictures of
higher resolutions than 800 x 600.
• The picture with a SYNC on G (Green) signal may
jitter.
• The picture with a SYNC on G (Green) signal may
be tinged with green.
• If the resolution and frequency of your computer
are not shown on the table, change the resolution
of your computer. You may find the compatible resolution and frequency.
• Set the COMPUTER INPUT in SIGNAL menu to RGB,
when inputting the HDTV signal as RGB signal.
• Set the SIGNAL menu and USER menu as shown
below, when 525p signal is inputted.Set TRACKING first.
HORIZ. POSITION .............................
143
VERT. POSITION................................
54
TRACKING ............................. 800
COMPUTER INPUT ............... YC
BCR/YPBPR
CLAMP POSITION .............................
+9
CLAMP WIDTH ..................................
+3
HORIZ.PIXELS ....................... 620
VERT.LINES ........................... 444
VERT.SYNC. ........................... ON
HOLD ...................................... ON2 BEGIN -1
END 8
Picture adjustment (continued)
Signal mode resolution horizontal Vertical Normal mode Real mode
(H x V) frequency (kHz) frequency (Hz) (H x V) (H x V)
TV60 – 15.73 59.94 800 x 600 –
TV50 – 15.63 50.00 800 x 600 –
1080i – 33.75 60.00 800 x 450 –
720p – 45.00 60.00 800 x 450 –
PC98 640 x 400 24.82 56.42 800 x 500 640 x 400
CGA70 640 x 400 31.47 70.09 800 x 500 640 x 400
CGA84 640 x 400 37.86 84.14 800 x 500 640 x 400
CGA85 640 x 400 37.86 85.08 800 x 500 640 x 400
VGA60 640 x 480 31.47 59.94 800 x 600 640 x 480
VGA72 640 x 480 37.86 72.81 800 x 600 640 x 480
VGA75 640 x 480 37.50 75.00 800 x 600 640 x 480
VGA85 640 x 480 43.27 85.01 800 x 600 640 x 480
SVGA56 800 x 600 35.16 56.25 800 x 600 800 x 600
SVGA60 800 x 600 37.88 60.32 800 x 600 800 x 600
SVGA72 800 x 600 48.08 72.19 800 x 600 800 x 600
SVGA75 800 x 600 46.88 75.00 800 x 600 800 x 600
SVGA85 800 x 600 53.67 85.06 800 x 600 800 x 600
XGA43i 1024 x 768 35.52 86.96 800 x 600 800 x 600
XGA60 1024 x 768 48.36 60.00 800 x 600 800 x 600
XGA70 1024 x 768 56.48 70.07 800 x 600 800 x 600
XGA75 1024 x 768 60.02 75.03 800 x 600 800 x 600
XGA85 1024 x 768 68.68 85.00 800 x 600 800 x 600
MAC13 640 x 480 35.00 66.67 800 x 600 640 x 480
MAC16 832 x 624 49.72 74.55 800 x 600 800 x 600
MAC19 1024 x 768 60.24 75.02 800 x 600 800 x 600
MAC21 1152 x 870 68.59 74.96 800 x 600 800 x 600
HP75 1024 x 768 62.94 74.92 800 x 600 800 x 600
Page 21
EN – 21
ENGLISH
Advanced features for presentation
Expand
By pressing the EXPAND button on the remote control, you can magnify the detailed image of the picture.
You can also view the screen displaying the picture as
its original size (native resolution display).
Setting the Expand mode
1. Press the MENU button.
2. Press the $ or % to select the FEATURE menu.
3. Press the ENTER button.
4. Press the { or } button to select EXPAND MODE.
5. Press the $ or % to set the EXPAND MODE.
6. Press the MENU button twice to exit the menu system.
Still
How to stop the picture temporarily (still picture).
1. Press the STILL button on the remote control.
The picture will freeze temporarily.
To resume picture activity.
2. Press the STILL button on the remote control
again.
Using the Expand mode
1. Press the EXPAND button.
• You can magnify different areas of the active pic-
ture by pressing the {, }, $, % button.
• You can change the magnification of the zoomed area
by pressing the + or - button.
2. Press the EXPAND button on the remote control
again.
The normal screen display will appear on the screen.
• Display enlargement does not work with
video input or S-video input.
REAL screen display
• During REAL mode, Press the $ or % buttons
for fine adjustment. The { and } buttons are
not working at this time.
(EXPAND MODE 1) (EXPAND MODE 2)
Real screen display
Zooming
image
EXPAND MODE
Page 22
EN – 22
The lamp is designed to project the image on the LCD
panels. When the lamp no longer functions, replace it
with a new one.
Caution:
• Do not remove the lamp immediately after turning
off the lamp of the projector, you may get burned
because of the high temperature of the lamp.
• For lamp replacement, press the power button to
power off, then wait for 60 seconds in stand-by mode
to allow the lamp and LCD panels to cool. Then turn
off the main switch, unplug the power cord from
the outlet, and wait one hour so that the lamp is
cooled to the touch.
• Do not remove the lamp except for replacement.
Careless treatment can cause injury or fire.
• Do not touch the lamp element directly. It may break
and cause you to injure or burn yourself.
• Be sure not to drop the lamp lid screw into the projector. Also be sure not to insert metal or any flammable objects, it may cause fire or electric shock. If
any objects are inserted, please unplug and contact
your dealer.
• Install the lamp securely, failure may cause a fire.
1. Reverse the projector gently.
2. Loosen the screws of the lamp lid on the top cover
using a phillips screwdriver (+) , and remove
the lid.
• Remove the lamp
cover in the direction
of the arrow as
indicated.
3. Loosen screws (a) using a
phillips screwdriver (+).
4. Pull up the handle.
5. Hold onto the projector by the
handle as you pull out the
lamp.
• Pull out the lamp straight
upward.
• Once the lamp has been re-
moved, do not spill liquid
on it, place it near flammable objects or where
children can touch it.
Otherwise, it will
cause injury or fire.
6. Insert the new lamp securely into the projector
body in the right direction.
• Make sure that the two positioning bosses (b) fit to
the lamp positioning holes before inseting the lamp.
7. Put the handle back to the
holding point.
• Make sure that the
handle is locked.
8. Tighten up the screws (a)
using a phillips screwdriver
(+).
9. Tighten up the screws of the
lamp lid using a phillips
screwdriver (+).
How to reset the operation time meter
Plug in the power cord, switch on the projector, and
reset lamp time by pressing the $, % and POWER
buttons simultaneously.
Caution:
• Do not spill liquid on the lamp or place it near flammable objects or where children can touch it. Otherwise, it could cause injury or fire.
• Be sure that the projector guide is firmly inserted
between the right and left lamp guides.
Important:
• The projector will not turn on if you do not secure
the lamp lid.
• You must reset the operation time meter after
you replace the lamp.
• Do not reset the operation time meter unless the
lamp has been replaced.
Interval of the lamp replacement
The interval of the lamp replacement about 2,000 hours
of consecutive use. Replacement span may differ according to operating environment, and may be shorter
than 2,000 hours. Decreases in luminescence and/or
color brightness will indicate that the light source lamp
needs to be replaced. When lamp operation time exceeds 1,500 hours, the indicator will flash alternately
between green and red (while the lamp is in operation;
when the lamp is not in operation, the indicator will
appear red only). When the lamp has been used for
about 1,900 hours, the message “LAMP!!.” will appear
on the screen for one minute. When the lamp has been
used for about 2,000 hours, the projector will automatically shut off for safety and the power indicator light
will be red. The projector cannot be used until the lamp
has been replaced and operation timer has been reset.
Caution:
• The lamp is fragile. If broken, be careful not to cut
yourself with glass fragments.
• The replacement span of the lamp depends on the
environment. For replacement lamps, please contact your dealer.
The projector automatically shuts off when the
lamp is used up in about 2,000 hours and cannot
be used until the lamp is replaced and the internal timer is reset.
Lamp replacement
Screw of the lamp lid
(a)
(b)
(a)
Page 23
EN – 23
ENGLISH
Maintenance
Caution:
Be sure to turn off the projector and unplug the power
cord from the wall outlet before you perform any maintenance on the projector.
Cleaning the air-filter
Clean the air-filter frequently (about once a month). If
the filter or ventilation slots become clogged with dirt
or dust, the temperature inside of the projector may
rise and cause some troubles, such as damage of inside parts, and shortening the life of panel.
• When the temperature inside of the projector
rises, the TEMP indicator blinks in red, and the
power will be shut off to be stand-by which LAMP
indicator is turned off.
For side air outlet grill
1. To remove the filter cover, press the ridged area gently,
push the cover in the direction of the arrow and lift.
2. Remove the air-filter from
the filter cover.
3. Wash the air-filter.
• Use water or a mild
detergent diluted with
water to clean the filter.
Rinse the filter thoroughly and let it dry
completely.
4. Attach the filter to the cover.
5. Reinstall the filter cover.
Important:
• If the filter is damaged or becomes extremely
dirty, contact your dealer for replacement.
• The power will not turn on if the air-filter cover is
improperly installed.
Caution:
Be sure to use the projector with an air-filter. If not,
dust may get inside the projector, causing a fire or a
breakdown.
Cleaning the projector and the ventilation
grill
Use a soft cloth to clean the projector and the ventilation grill. When the grill become dirty, wipe them with
a soft cloth dampened with a diluted mild detergent,
and then wipe them with a dry cloth.
To protect the surface of the projector from fading or
deteriorating:
• Do not spray insecticide on or inside the projector.
• Do not use benzine or thinner to clean it.
• Do not let rubber or plastic materials come into
contact with the projector.
Cleaning the lens
Use a standard lens-cleaning brush or a piece of lens
tissue dampened with lens cleaning fluid. The lens surface is fragile. Use only recommended, nonabrasive
lens-cleaning materials. Do not touch the lens with your
fingers.
Filter
Filter cover
Page 24
EN – 24
Troubleshooting
The following offers solutions to some of the common problems you may encounter. We suggest that you consult
this chart before contacting your dealer.
CAUSE
• The air inlet grill, outlet grill or air filter is
clogged with dust or some objects.
POWER indicator does not light up.
• Power cord is unplugged from the outlet.
• Power cord is disconnected from the projector.
• The main switch is turned off.
• The lamp lid is open.
POWER indicator blinks red.
• The projector has been turned on again too soon
after having been turned off.
• When the power switch was turned off while
the fan was running, during or after lamp
operation.
• The room temperature is too high.
(Does the LAMP indicator show an unusual
condition?)
•
Lamp is no longer working.
POWER indicator blinks between red and green.
• The filter cover is not closed.
• When the LAMP indicator or the TEMP
indicator is either on or blinking, the main unit
requires repairs.
•
Lens is covered by lens cap.
• When the LAMP indicator or the TEMP
indicator is either on or blinking, the main unit
requires repairs.
•
The equipment connected to this projector is not
turned on.
•
Hookup is not made correctly with other equipment.
•
The input source is not selected correctly.
• The air inlet grill, outlet grill or air filter is
clogged with dust or some objects.
(In this case, the TEMP indicator does not light up.)
•
The projector is not at a right angle to the screen.
•
Brightness, tint and color are not adjusted correctly.
•
The projecting distance is beyond the focused area.
•
Lens is dirty.
•
Screen size exceeds screen size specifications.
•
Brightness and contrast are not adjusted correctly.
•
FINE adjustment is not made correctly.
• Tracking is not adjusted.
•
The projector is not at a right angle to the screen.
•
Remove the object.
•
Plug the power cord into the outlet.
• Insert the power cord into the projector.
•
Turn the main switch on.
• Close the lamp lid.
•
Wait for the lighting sequence.
• Turn the power switch on and off several times.
•
Refer to "Indicators" on page 25.
•
Replace the lamp with a new one.
•
Close the cover correctly.
•
Contact your dealer.
•
Take the lens cap off.
•
Replace the lamp with a new one.
•
Turn on the connected equipment.
• Confirm the hookup.
•
Select the correct source according to the equipment connected to this projector.
•
Remove the object and turn off the main power
switch. After about 10 minutes, Turn the projector on.
•
Adjust the angle of the projector to make a right
angle to the screen. See page 12.
•
Adjust brightness, tint and color correctly.
•
Adjust the projecting distance. See page 9.
•
Clean lens.
•
Reduce screen size to within 40" to 300".
•
Adjust brightness, contrast.
•
Make FINE adjustment.
• Adjust tracking.
•
Adjust the angle of the projector to make a
right angle to the screen. See page 12.
•
When you see the stationary image for a long time, it may remain on the screen if you change the
image. It is not a breakdown. The blurred image will disappear in a few minutes.
•
It is normal.
•
The cable for connection with other equipment
is not plugged securely into the terminal.
•
The projector is installed too close to other
equipment.
•
Volume is not turned up.
•
Connection to other equipment is not made correctly.
•
The PC monitor is not turned on.
•
This is typical of the LCD projector.
•
The operation is incorrectly made due to noise or
interference.
•
Plug the connecting cable securely into the
terminal. See pages 10-11.
•
Install the projector far away from other equipment.
•
Turn up the volume.
• Check connections. See pages 10-11.
•
Turn on the monitor.
•
Press the reset button on the Terminal board.
See page 15.
POSSIBLE SOLUTIONS
PROBLEMS
The power is off.
No picture appears
on the screen.
The image is
turned off.
The image is
distorted.
The image is dark.
The image is
blurred.
Red, blue or green dots are
viewed on the text of image.
The image remains
blurred.
The image is distorted on the screen
and noise is heard.
No sound is heard.
Adjustments cannot be
made.
Warm air comes out of
the exhaust vents.
Nothing is displayed on
the PC monitor.
Page 25
EN – 25
ENGLISH
Indicators
The projector has three LED Indicators which shows the working condition of the projector.
The following offers solutions to possible problems. If a problem persists, turn the projector off and consult your
dealer.
Normal condition
Abnormal condition
Steady
red
Steady
green
Steady
green
Blinking
green
Steady
green
POWER LAMP TEMP
CONDITION Notes
The POWER is ON. (Normal condition)
Lamp stand-by (about for 1 minute) The power button cannot be used to switch
ON and OFF
Stand-by
OffOff
Off
Off
➝
➝
LAMP indicator
POWER indicator
TEMP indicator
POWER
LAMP
VOLUME
TEMP
VIDEO
ENTER
MUTE
MENU
SOURCE
COMPUTER
AUTO POSITION
Steady
green
Blinking
green/red
Blinking
green/red
Blinking
green/red
Steady
red
Steady
green
Steady
green
Blinking
red
Blinking
red
POWER LAMP TEMP
CONDITION POSSIBLE SOLUTIONS
Lamp duration warning. (Lightning duration total
about 1, 500 hours.When the POWER is ON.)
Steady
red
Blinking
red
Lamp duration warning. (Lightning duration total
about 1, 500 hours.When the POWER is OFF.)
Steady
red
Lamp duration warning. (Lightning duration total
about 2,000 hours.)
The lamp or filter cover is not closed.
The protection circuit is working or lamp is abnormal.
Close the cover correctly.
or or
Blinking Blinking
Abnormal. Contact your dealer.
Off
Off
Steady
red
Blinking
green
Off
Off
Off
Off
Off
Steady
red
Steady
Steady
Unusual temperature
• The ventilation slits or air filter is clogged with
dust or debris.
• The fan has stopped due to an impediment.
• The room temperature is too high.
• The filter is dirty.
• Remove the object from the ventilation
slits.
•
Pull out the power plug andremove the
object. If you cannot, consult your dealer.
• Relocate the projector to a cooler place.
• Clean the filter.
Replace the lamp.
Exchange with a new lamp if the same
problem recurs.
• Wait until the LAMP indicator is turned
off, then press the POWER button.
• Replace the lamp.
➝
➝
➝
➝
➝
➝
➝
➝
➝
➝
➝
➝
➝
➝
➝
➝
➝
➝
Page 26
EN – 26
Specifications
LCD projector
LVP-SA51U
AC100V ~ 240V, 50 / 60Hz
2.3 A
0.9-inch LCD panel: 3 pieces (for R, G, B)
Pixels 800 × 600 = 480,000 pixels
Total 1,440,000 pixels
Active pixel rate: 99.99 % or more (each panel)
16,770,000 colors
F 2.3~2.6 f = 36.0 mm ~ 43.2 mm
150 W UHP (2, 000 Hours)
40 inch ~ 300 inch (aspect ratio 4:3)
Resolution : 640 x 400 - 800 x 600 + Compressed 1024 x 768
Sync on Green available
NTSC / NTSC 4.43 / PAL (including PAL-M, N) / SECAM, PAL-60
DVD (Component) / HDTV (1080i) / 720p / (525p)
1 W mono
3 cm x 4 cm square type (8Ω 1W)
Luminance signal: Vp-p=1.0V 75Ω (negative sync.)
Chroma signal: Vp-p=0.286V 75Ω (burst signal)
Vp-p=1.0V 75Ω (negative sync.)
350 mVrms, 10kΩ or more
RGB: Vp-p=0.7V 75Ω (negative sync.)
YCBCR: Y: Vp-p=1.0V (negative sync.) CBCR: Vp-p=0.7V
HD/CS : TTL level (positive or negative)
VD : TTL level (positive or negative)
Serial (Mini DIN 8P female connector) RS-232C standards
242 mm × 79 mm × 294 mm (9.5 inch × 3.1 inch × 11.6 inch)
(width × height × depth)
Approx. 3.4 kg (7.5 lbs)
2.9m (9.5 feet)
+41°F (+5°C) ~ +95°F (+35°C), 30~90%
Type
Model
Rated power supply
Rated input
LCD panels
Colors
Projection lens
Light source lamp
Picture size
PC compatibility
Video compatibility
Audio output
Speaker
S-video input
Video input
Audio inputs
Analog RGB input
(mini D-SUB 15P)
Control connector
Outside dimensions
Weight
Length of power cord
Temperature, humidity
(performance guarantee)
Legs and lens are not included.
Kensington Lock
This projector has a Kensington Security Standard connector for use with a Kensington MicroSaver Security
System. Refer to the information that came with the Kensington System for instructions on how to use it to
secure the projector. Please contact to Kensington Technology Group as shown below.
Kensington Technology Group
2855 Campus Drive
San Mateo, CA 94403, U.S.A.
Phone : (650)572-2700 Fax : (650)572-9675
Page 27
EN – 27
ENGLISH
Connectors
PC analog RGB input
Use to input video signals (analog
RGB) of a personal computer.
(Pin assignment of Mini D-SUB 15P jack)
PIN NO. SPEC PIN NO. SPEC
1 R(RED)/CR 9–
2
G(GREEN)/Y
10 GROUND
3
B(BLUE)/CB
11 GROUND
4 GROUND 12 –
5 GROUND 13 HD/CS
6 GROUND 14 VD
7 GROUND 15 –
8 GROUND
1
5
10
11
15
RS-232C input
Use to control the projector with the
personal computer, or control the
personal computer with remote control. Use the provided RS-232C cable (Mini
DIN 8P-D-SUB 9P) for the connection.
PIN NO. NAME I/O
1 TXD IN
2 RTS IN
3 DTR IN
4 GND –
5 CTS/5V IN / OUT
6 DCD/CLOCK OUT
7 RXD OUT
8 RI/DATA OUT
12
6 8
5
3
1 Remote control 939P840-10
1 User manual 871D305-10
1 Quick reference card 857B033-10
2 Battery for remote –
1 Carrying case 772P032-30
Replacement part
(Option / Not included in the box)
Spare Mercury lamp 499B024-10
(VLT-PX1LP)
What’s included in the box
2 AC power cord 246C383-10
246C383-20
1 AV(Audio/Video) cable 246C381-10
1 RGB cable for PC 246C394-10
1 RS-232C cable 246C366-10
f72.5
265 11
89.5
79
47.5
(10.5)
f18
122.3
242 7
294 26.5
155
f26
147.5 31.5
f26
Dimensional drawings
(mm)
Page 28
1
Control projector by using a personal computer
1) Interface
This projector can be controlled by connecting a personal computer with RS-232C terminal.
Functions can be controlled by a personal computer:
• Turn the ON or OFF
• Changing input signals
• Menu setting
Connection
Projector + IBM PC or IBM PC compatibles
O
I
S-VIDEO
VIDEO
AUDIO L
(MONO)
AUDIO R
AC IN
MAIN
VIDEO IN
COMPUTER INCOMPUTER OUT
RS-232C
to Com1
Comport
to RS-232C
terminal
RS-232C cable
D-SUB 9PMini DIN 8P
Important:
• Make sure that your computer and projector are turned off before connection.
• Turn on the projector after the computer is started up.
(If you do not follow this order, the Comport may not function.)
• If your PC (IBM or IBM compatible) is equipped only with a 25-pin serial port connector, a 25-pin serial port
adapter is required. Contact your dealer for details.
O
I
S-VIDEO
VIDEO
AUDIO L
(MONO)
AUDIO R
AC IN
MAIN
VIDEO IN
COMPUTER INCOMPUTER OUT
RS-232C
to RS-232C
terminal
RS-232C adaptor
for Macintosh (optional)
to modem port
or printer port
D-SUB 9P D-SUB 9P Mini DIN 8PMini DIN 8P
RS-232C cable
PROTOCOL RS-232C
BAUD RATE 9600 [bps]
DATA LENGTH 8 [bits]
PARITY BIT NONE
STOP BIT 1 [bit]
FLOW CONTROL NONE
This projector uses RXD, TXD and GND lines for RS-232C control.
For RS-232C cable,the reverse type cable should be used.
2) Control command diagram
The command is structured by the address code, function code, data code and end code. The length of the
command is different by each function.
Address code Function code Data code End code
HEX 30h 30h Function Data 0Dh
ASCII '0' '0' Function Data
[Address code] 30h 30h (In ASCII code, '0' '0') fixed.
[Function code] A code of each fixed control move.
[Data code] A code of each fixed control data (number) and not always indicated.
[End code] 0Dh (In ASCII code, ' ') fixed.
LCD Projector
LVP-SA51U
Projector + Macintosh
Page 29
2
3) Control sequence
(1) Send the command from a personal computer to the projector. (The commands must be sent at least
400ms apart.)
(2) The projector will send a return command 400ms* after it has received an end code. If the command is
not received correctly, the projector will not send the return command.
(3) The personal computer checks the command and confirms if the command which has been sent has been
executed or not.
(4) This projector sends various codes other than the return code. When having a control sequence by RS-
232C, reject other codes from personal computer side.
• * : The sending time of return command may delay depending on the condition (during changing the
input signal, etc.).
[Example] Turn the power ON (' 'is for ASCII code)
Sending commands Status code from Meaning
from the PC etc. projector
30 30 21 0D Command for POWER ON
'0' '0' '!' ' '
30 30 21 0D Command received
'0' '0' '!' ' ' (Command echo back)
Sending commands Status code from Meaning
from the PC etc. projector
30 30 5F 72 31 0D Command for setting the input
'0' '0' '_' 'r' '1' ' ' signal to COMPUTER
30 30 5F 72 31 0D Command received
'0' '0' '_' 'r' '1' ' ' (Command echo back)
Operation
ASCII HEX
POWER ON ! 21h
POWER OFF " 22h
INPUT COMPUTER _r1 5Fh 72h 31h
INPUT VIDEO _v1 5Fh 76h 31h
4) Operation commands
The operation commands execute the basic operation setting of this projector. It may not operate when changing the signal.
• POWER OFF command will not work for 1 minute after the power is turned on.
• POWER ON command will not work for 1 minute after the power is turned off.
[Example] Set the input signal to COMPUTER (' 'is for ASCII code)
5) Volume commands
The volume commands execute the volume setting of this projector with the value.
[Example] Set the volume to 30 (Standard value) (' 'is for ASCII code)
Sending commands Status code from Meaning
from the PC etc. projector
30 30 56 4C 33 30 0D Command for setting the volume
'0' '0' 'V' 'L' '3' '0' ' '
30 30 56 4C 33 30 0D Command received
'0' '0' 'V' 'L' '3' '0' ' ' (Command echo back)
ITEM ASCII HEX VALUE
VOLUME VL 56h 4Ch 00 - 60
How to set the grade
Use ASCII letters code to set the grade for setting data. Please refer to the table below for HEX code.
ASCII '0' '1' '2' '3' '4' '5' '6' '7' '8' '9'
HEX 30h 31h 32h 33h 34h 35h 36h 37h 38h 39h
Page 30
3
Sending commands Status code from Meaning
from the PC etc. projector
30 30 72 35 34 0D Command as same as MENU button
'0' '0' 'r' '5' '4' ' '
30 30 72 35 34 0D Command received
'0' '0' 'r' '5' '4' ' ' (Command echo back)
[Example] Display MENU selection bar. (' 'is for ASCII code)
Button's name on remote
ASCII HEX
+ VOLUME r06 72h 30h 36h
– VOLUME r07 72h 30h 37h
EXPAND r02 72h 30h 32h
MUTE ra6 72h 61h 36h
{ r53 72h 35h 33h
} r2b 72h 32h 62h
$ r4f 72h 34h 66h
% r59 72h 35h 39h
MENU r54 72h 35h 34h
ENTER r10 72h 31h 30h
AUTO POSITION r09 72h 30h 39h
STILL ra4 72h 61h 34h
6) Remote commands
Some remote control operations can be done by remote command codes.
7) Reading command diagram
Monitor projector operation status. The power ON, OFF and input terminal settings can be monitored.
ASCII HEX
Function Data (Receive) Function Data (Receive)
POWER ON vP 1 76h 50h 31h
POWER OFF vP 0 76h 50h 30h
INPUT COMPUTER vI r1 76h 49h 72h 31h
INPUT VIDEO vI v1 76h 49h 76h 31h
Sending commands Status code from Meaning
from the PC etc. projector
30 30 76 49 OD Command to confirm input
'0' '0' 'v' 'I' ' '
30 30 76 49 76 31 0D Command (Input is Video)
'0' '0' 'v' 'I' 'v' '1' ' ' carrired out
When a personal computer sends the command, data code will not be attached. On the other hand, the projector
which has received a command will attach the recent operating status and then send.
[Example ] Input was Video when the operating status of the input terminal was confirmed.
8) Menu setting commands
The menu setting commands execute the menu setting of this projector. If the personal computer doesn’t send
the commands without attaching the data code, the projector which has received the command replays the
setting data as data code.
ITEM ASCII HEX VALUE
CONTRAST P 50h ±30±30±30 (R from G+Main data+B from G)
BRIGHTNESS Q 51h ±30±30±30 (R from G+Main data+B from G)
COLOR MATRIX (MODE)
CMT 43h 4Dh 54h 1, 2, 3, 4 (USER), 5 (OFF)
COLOR MATRIX (R, G, B)
MRGB 4Dh 52h 47h 42h ±30±30±30 (R+G+B)
COLOR MATRIX (Y, C, M)
MYCM 4Dh 59h 43h 4Dh ±30±30±30 (Y+C+M)
COLOR TEMP. A 41h 1 (Standard), 2 (High), 3 (Low), 4 (User)
SHARPNESS R 52h ±10
TINT S 53h ±10
COLOR T 54h ±10
Page 31
4
ITEM ASCII HEX VALUE
AUTO POWER ON APON 41h 50h 4Fh 4Eh 0 (OFF), 1 (ON)
AUTO POWER OFF APOF 41h 50h 4Fh 46h 00 (Off) , 05, 10, 15, 30, 60
IMAGE REVERSE IR 49h 52h 0 (OFF), 1 (Mirror), 2 (Invert), 3 (Mirror invert)
MENU POSITION MP 4Dh 50h 0 (Upper left), 1 (Lower right)
EXPAND MODE EX 45h 58h 1 - 2
AUDIO MODE AU 41h 55h 1 (COMPUTER), 2 (VIDEO), 3 (COMPUTER & VIDEO)
VIDEO SIGNAL VS 56h 53h 0 (AUTO), 1 (NTSC), 2 (PAL), 3 (SECAM) ,
4 (4.43NTSC), 5 (PAL-M), 6 (PAL-N), 7 (PAL-60)
ANAMORPHIC SC 53h 43h 0 (OFF), 1 (ON)
LANGUAGE LG 4Ch 47h 0 (
), 1 (English), 2 (Español), 3 (Deutsch) ,
4 (Frençais), 5 (Italiano), 6 ( )
RESET ALL
RSTALL
52h 53h 54h 41h 4Ch 4Ch
MEMORY CALL MMC 4Dh 4Dh 43h 0 (AUTO), 1 (USER1), 2 (USER2)
HORIZ. POSITION HP 48h 50h + (increase), – (decrease)
VERT. POSITION VP 56h 50h + (increase), – (decrease)
FINE SYNC. FN 46h 4Eh 00 - 39
TRACKING TRK 54h 52h 4Bh + (increase), – (decrease)
COMPUTER INPUT CIN 67h 49h 4Eh 0 (RGB), 1 (YCBCR/YPBPR)
HOLD HLD 48h 4Ch 44h 0 (AUTO), 1 (ON), 2 (OFF)
HOLD BEGIN HLB 48h 4Ch 42h –01 - –99
HOLD END HLE 48h 4Ch 45h 01 - 99
CLAMP POSITION CLP 43h 4Ch 50h 00 - 63
CLAMP WIDTH CLW 43h 4Ch 57h 01 - 63
HORIZ. PIXELS HPL 48h 50h 4Ch 0000 - 9999
VERT LINES VLN 56h 4Ch 4Eh 0000 - 9999
PLL PLL 50h 4Ch 4Ch 0 (AUTO), 1 (0), 2 (1), 3 (2), 4 (3), 5 (4), 6 (5), 7 (6), 8 (7)
VERT.SYNC VSC 56h 53h 43h 0 (AUTO), 1 (ON), 2 (OFF)
SHUTTER (U) SHU 53h 48h 55h 000 - 299
SHUTTER (L) SHL 53h 48h 4Ch 000 - 299
SHUTTER (LS) SHLS 53h 48h 4Ch 53h 000 - 398
SHUTTER (RS) SHRS 53h 48h 52h 53h 000 - 398
How to set the grade
Use ASCII letters code to set the grade for setting data. Please refer to the table below for HEX code.
ASCII '+' '–' '0' '1' '2' '3' '4' '5' '6' '7' '8' '9'
HEX 2Bh 2Dh 30h 31h 32h 33h 34h 35h 36h 37h 38h 39h
[Example 1] Set the AUTO POWER ON to ON.
[Example 2] Set the difference data of R from G to +10, the setting main data to 0 and the difference data of
B from to -5.
Sending commands Status code from Meaning
from the PC etc. projector
30 30 50 2B 31 30 2B 30 30 2D 30 35 0D Command for setting the
'0' '0' 'P' '+' '1' '0' '+' '0' '0' '-' '0' '5' ' ' picture control
30 30 50 2B 31 30 2B 30 30 2D 30 35 0D Command received
'0' '0' 'P' '+' '1' '0' '+' '0' '0' '-' '0' '5' ' ' (Command echo back)
Sending commands Status code from Meaning
from the PC etc. projector
30 30 41 50 4F 4E 30 0D Command for setting the
'0' '0' 'A' 'P' 'O' 'N' '1' ' ' AUTO POWER ON to ON
30 30 41 50 4F 4E 30 0D Command received
'0' '0' 'A' 'P' 'O' 'N' '1' ' ' (Command echo back)
The data code of CONTRAST and BRIGHTNESS is structured by the difference data of R from G, the main data and the difference
data of B from G.
[Example 3] The TINT was set to +10 when the setting status was confirmed.
Sending commands Status code from Meaning
from the PC etc. projector
30 30 53 0D Command to confirm
'0' '0' 'S' ' ' setting of TINT
30 30 53 2B 31 30 0D Command (setting of TINT
'0' '0' 'S' '+' '1' '0' ' ' is +10) carried out
Loading...