Mitsubishi Electronics JT-SB216JSH-H-E, JT-SB216JSH-S-E, JT-SB216KSN-W-E, JT-SB216JSH-W-E User Manual

Hand dryer

GB

MODEL

JT-SB216JSH-W-E
JT-SB216JSH-H-E
JT-SB216JSH-S-E
JT-SB216KSN-W-E Heater-less Model

Heater Model

1109875HD4101

Model Name
Display Position
Power voltage
display position.

Appliance color -W

(White)

INSTALLATION MANUAL

Read this manual thoroughly before beginning installation to ensure the appliance is installed safely and correctly.

Local installation standards should be obeyed and installation should be performed by the dealer or a qualified
professional.

The "INSTRUCTION MANUAL" is for the customer. Be sure to hand it to the customer.

(Dark grey)

, -H

, -S

(Silver)

Single-phase 220-240VAC

For Dealers and Installers

INDEX
Safety Precautions …………………………………………………… 2

Pre-installation checks ……………………………………………… 3

■ Checking the installation environment

■ Checking the appliance, accessories, and items required for installation

………………………………… 3

… 3

Names of parts and external dimensions ………………………… 4
Installation conditions ………………………………………………… 5

■ Required space for installation

■ Suitable walls

■ Making the appliance easier to use

……………………………………………………… 5

……………………………………… 5

………………………………… 5

Installation method ……………………………………………… 6~10
Test Run ……………………………………………………………… 11

− 1 −

Safety Precautions

󱾁

󱾁

Prohibited

󱾁

Do not

disassemble

󱾁

Do not use in the

bathroom/

shower room

Warning

Do not install in locations where salt damage may
occur, or where corrosive, neutral, or reductive
gases are present.

This may cause malfunctions.

Do not scratch, damage, process, excessively
bend, pull, twist or bundle the power cable, and
do not place heavy objects onto it or trap it.

Doing so may damage the power cable, causing fires or
electric shocks.

Do not attempt any disassembly or modification
of the appliance that is not expressly stated in this
manual.

Doing so may result in fires, electric shocks or injuries.

Do not use in a hot location such as a shower
room, where condensation may form on the
appliance, or where water may splash directly
onto the appliance.

This may cause electric shocks or malfunctions.

The following may lead to death or serious personal
injury if the appliance is handled incorrectly.

Follow

instructions

Electrical wiring work should be done by a certified

󱾁

professional in conformance with the technical
standards for the equipment or official standards.

Incorrect wiring can cause electric shocks and fires.

Use single-phase 220-240V power.

󱾁

Using the incorrect power supply may cause fires, electric
shocks or malfunctions.

Use exclusive wiring

󱾁

Using this appliance with other devices on a branch
socket may cause abnormal heat, which may cause fires.

Be sure to install a ground-fault circuit interrupter.

󱾁

Not doing so may result in electric shocks.

A means for disconnection must be incorporated

󱾁

in the fixed wiring in accordance with the wiring
rules.

Prohibited

Cautions

Do not install when the product (power cable) is

󱾁

electrified.

Doing so may result in electric shocks.

The following may lead to injury or damage to
property if the appliance is handled incorrectly.

Install securely in a location strong enough to

󱾁

support the weight of the appliance.

Injuries may be caused if the appliance falls off the wall.

Follow

instructions

Wear gloves when installing the appliance.

󱾁

Not doing so may result in injuries.

− 2 −

Pre-installation checks

■ Checking the installation environment
Do not install in the following types of location.

(This may cause malfunctions.)

󱾁 Outdoors 󱾁 Locations where the temperature could be lower than 0ºC. 󱾁 Locations where there is a lot of dust
󱾁 Locations where the temperature could be higher than 40ºC 󱾁 Locations where there is a lot of condensation
󱾁 Locations where salt damage could occur 󱾁 Vehicles (including ships and airplanes)
󱾁 Locations where corrosive, neutral, or reductive gases are present
󱾁 Near food or tableware 󱾁 Kitchens 󱾁 Locations where the appliance may come into direct contact with water

(Where there is a risk of water splashing)

󱾁 Locations where the appliance is direct sunlight or strong light.

(May cause the sensor to malfunction)

󱾁

Rooms that have a sterilization basin, swimming pools, bathrooms.

■ Check the appliance, accessories, and items required for installation

Product

Main unit

Required items

Screwdriver

Longer than 150mm

Mounting screws (5 x 30 Type 1 tapping screws)… 6

Installation panel…1

Cord clip …1

Clip mounting screw…1

Drain tank

Air filter

Pen
To mark position to insert metal

screw plugs in the wall

Ferrite core…1

Switch door screw…1

Accessories

■ Prepare if required
Single wire for internal wiring

(Cable core: between 1.0mm
and 2.5mm2)

※ Not needed if the

internal wiring is
c

omplete

2

SCREW ANCHOR…6

※ Use on concrete walls

Wall reinforcement

※ Reinforces walls made

of materials other than
concrete

■ Check the heater settings and air speed settings (JT-SB216JSH type only)
Check the heater ON/OFF settings and air speed HIGH/STANDARD settings with the customer beforehand.

(The customer cannot adjust the settings after installation is complete.)

− 3 −

Names of parts and external dimensions

168

Terminal block

Power cable hole
(rear)

Terminal block

Drain tank

Air filter (air intake)

393

10

267

80

263

68

（79.5）

300

（103.5）

※

Installation
panel

670

658

※ Maximum width

of main unit

219

93

77

189

Unit (mm)

2

50 (Insertable dimensions)

■ Front

■ Rear

Power control section

Switch door

Power

ON
OFF

Power switch

Display

Heater type
(JSH)

Heater-less type
(KSN)

Power Heater

Power lamp

Heater lamp

Power Check

Check lamp Power lamp

Power cable hole

Front panel

Front panel
mounting scre

Terminal block

ws

Clip hole

− 4 −

Installation conditions

■ Required space for installation

Cautions

󱾁 Be sure to secure at least the distances

listed in the right-hand table from walls,
flammable (combustible) materials and
so on.

󱾁 Ensure a distance of at least 130mm from

the floor. Failure to do so may result in dirt
or water entering the appliance, causing
damage.

󱾁 Ensure there is at least 150mm on

both sides of the appliance to allow for
maintenance.

■ Suitable walls

󱾁 Flat walls with no unevenness.
󱾁 Walls that can support the weight of the appliance.
󱾁 Reinforce any walls made with materials other than

concrete.

󱾁 When installing on a concrete wall, use commercially

available metal screw anchors.

Left

150

130

Below

Installation position guide

150

Wall

Right

Location Clearance

Top Open

Left 150mm
Right 150mm
Front Open

Below 130mm

Unit (mm)

■ Making the appliance easier to use

󱾁 Refer to the "Installation position guide".
󱾁 Leave at least 200mm clearance on the left to make

maintenance easier.

󱾁 Avoid locations where people or doors might bump

into the appliance.

For men: 925mm
For women: 905mm

− 5 −

Installation method

Warning

󱾁 Use single-phase 220-240V power.

Using the incorrect power supply may cause fires,
electric shocks or malfunctions.

󱾁 Do not install when the product (power cable) is

electrified.

Doing so may result in electric shocks.

Caution

Check

□ Single-phase 220-240V power is being used.
□ Make sure that a ground-fault circuit interrupter is installed in the fixed wiring.

□ A single wire (cable core: between 1.0mm2 and 2.5mm2) is being used for the power cable.

Make sure that a means for
disconnection is incorporated in the fixed

Power cable

wiring in accordance with the wiring rules.

󱾁 Follow the illustration on the right for the internal

wiring.

28.5

Approx. 500mm

267

1

Conduit box

Power cable hole (rear face)

Terminal block

15

6.5

68

230
207
164

57.5

Recommended

635

installation heights
For men: 925mm
For women: 905mm

Fix the installation panel to the wall using
the 4 mounting screws.

󱾁 The position illustrated on the right is

recommended.

󱾁 Use commercially available screw anchors when

installing the appliance on a concrete wall.

󱾁 Reinforce any walls made with materials other

than concrete before installation.

2

󱾁 Leave a space of at least 130mm below

the appliance.
Dirt or water sucked into the appliance
may damage it.

Appliance external shape

Appliance mounting screw
position

Unit (mm)

Mounting screws
(Included)

Installation
panel

Appliance shape

28.5

15

6.5

103.5

9.5

7

7

Detailed view of
installation holes

230
207
164

57.5

15.5

10

7

R3.5

Recommended

635

installation heights
For men: 925mm
For women: 905mm

R3.5

− 6 −

Appliance mounting
screw position

Unit (mm)

79.5 103.5

Installation (Continued)

1.Remove the drain tank and air filter.

2.Remove the front panel mounting screws (2),
and remove the front panel.

Air filter

Front panel mounting screws

Drain tank

Groove

3

3.Remove the terminal cover mounting screw (1),
and remove the terminal cover.

※ Be careful not to lose the rubber bushing.

Front panel

Rubber bushing

Termial cover
mounting screw

Terminal
cover

Terminal block

− 7 −

Installation (Continued)

Run the power cable through the hole in the back
of the appliance, and pull it through the appliance.

4

Warning

󱾁 Use single-phase 220-240V power.

Using the incorrect power supply may cause fires, electric shocks or
malfunctions.

Wire it to the terminal block. (No polarity)

1.Remove 15mm of wire sheath

2.Screw the power cable to the terminal block.

󱾁 Proper torque is 1.2Nm(11 lbf·in)

from the end.

Power cable

15mm

Hole

Power cable

70mm

Terminal
block

Screw

Power cable

.Check that the power cable is securely fixed

3

5

to the terminal block.

4.Wire the ground wire to the center terminal
of the terminal block.

󱾁 Proper torque is 1.2Nm(11 lbf·in)

Power
cable

Terminal
block

Terminal
block

screw

Ground wire

5.Clip and screw the power cable into the
position shown on the right.

Power cable hole

Power cable

Cord clip
(Included)

Mounting
screw

Cord clip mounting screw hole

− 8 −

Installation (Continued)

1.Run the power cable through the rubber
bushing, and attach the rubber bushing to
the terminal cover.

2.Attach the terminal cover to the main unit
using the terminal cover mounting screw.

3.Move the power cable to the left side of the
terminal cover.

4.Check that the power cable and wires are
not pinched anywhere.

6

Move the power
cable to the
left side of the
terminal cover.

Terminal cover
mounting screw

Rubber
bushing

Terminal
block

Terminal cover

5.Open the ferrite core.

6. Pass the power cable through the ferrite
core, and clos

󱾁 Place the ferrite core on the outside of the terminal

cover.

e it.

7. Check that the ferrite core is securely
installed.

Fix the main unit in place.

1.Engage the panel hooks of the installation
panel (2 hooks) on the back of the
appliance.

󱾁 If the wall is concrete, use commercially available

metal screw plugs.

󱾁 See "Plug Positioning" for details of where to insert

the plugs.

󱾁 Use a screwdriver that is longer than 150mm.

2.Check that the power cable is not trapped
behind the main unit.

󱾁 Adjust the length of the power cable in the switch

7

box so that the power cable does not become
trapped.

3.Gently press the appliance onto the wall,
and fix it in place using 2 mounting screws.

Cautions

󱾁 If you are using commercially

available φ 4 screws, use a washer
(external diameter φ 10 or less) to
prevent looseness.

Ferrite core
(Included)

Power cable

Mounting screws
(Included)

Longer than 150mm

Terminal cover

Installation panel

Panel hooks

Power cable

Plug positioning

− 9 −

Mark the wall in 2 places

■ Switching the air speed switch and heater switch settings

Check the heater ON/OFF settings and air speed HIGH/STANDARD settings with the
customer beforehand.

(The user cannot adjust the settings after installation is complete.)
(The JT-SB216KSN-W-E does not have an air volume switch or heater switch.)

Cautions

1.Remove the mounting screw (1) from

the switch box cover, and remove the
switch box cover.

8

2.Change the settings.

3.After checking the switches, fix the

switch box cover back in its original
position.

󱾁 Do not install when the product (power cord) is electrified.

Doing so may result in electric shocks.

Switches

Switch box cover

OFF

STANDARD

※

Factory default settings

ON

HIGH

HEATER

AIR SPEED

Mounting
screws

Settings

HEATER

AIR SPEED

OFF / ON

STANDARD / HIGH

1.Engage the groove of the front panel on
the appliance.

2.Reattach the front panel with the front
panel mounting screw

s (2).

3.Check that the front panel is fitted securely.

9

4.Attach the air filter.

5.Check that the air filter is inserted correctly,

all the way to the back.

6.Attach the drain tank.

Groove

Front panel

Front panel
mounting
screws

Drain tank

Main unit

Air filter

− 10 −

Test Run

Step What to check for Check

1

Check the power supply voltage

2 Turn the ground-fault circuit

interrupter on

3 Turn the power switch "ON". Is the power lamp in the display on?

4 Insert your hands to check if air is

being blown.

5

Insert your hands to check if warm
air is being blown.

T-

(Only with the J
when the heater is "ON".)
(The JT-SB216KSN model does not
have a heater)

6 Is the appliance mounted secure

※ Do not turn the power on while hands or other objects are inside the hand drying area.
※ If the display lamp flashes, turn the power switch "OFF", check that all of the lamps on the display section are off, and

then wait for 1 minute before switching the power back "ON".

SB216JSH type

Is single-phase 220-240V power being used?
Incorrect power supply may cause malfunctions.

Is the air blowing?

Is warm air blowing?
( If the room temperature is above 30ºC, for safety reasons

the heater will not operate even if the heater switch is
turned on.）

※ As the heater is a simple heater, if the room temperature

is less than 18ºC, the air may feel cold.

Is the heater lamp in the display on?

ly without any vibration or

abnormal noises?

− 11 −

Information on Disposal

Eng

Note: This symbol mark is for EU countries only.
This symbol mark is according to the directive 2002/96/EC Article 10 Information for users and Annex IV,
and/or to the directive 2006/66/EC Article 20 Information for end-users and Annex II.

lish

Your MITSUBISHI ELECTRIC product is designed and
manufactured with high quality materials and components which
can be recycled and/or reused.
This symbol means that electrical and electronic equipment,
batteries and accumulators, at their end-of-life, should be
disposed of separately from your household waste.
If a chemical symbol is printed beneath the symbol shown
above, this chemical symbol means that the battery or
accumulator contains a heavy metal at a certain concentration.
This will be indicated as follows:

Hg: mercury (0,0005%), Cd: cadmium (0,002%),

Pb: lead (0,004%)
In the European Union there are separate collection systems for
used electrical and electronic products, batteries and
accumulators.
Please, dispose of this equipment, batteries and accumulators
correctly at your local community waste collection/recycling
centre.
Please, help us to conserve the environment we live in!

Deutsch

Ihr MITSUBISHI ELECTRIC-Produkt wurde unter Einsatz von
qualitativ hochwertigen Materialien und Komponenten
konstruiert und gefertigt, die für Recycling und/oder
Wiederverwendung geeignet sind.
Dieses Symbol bedeutet, dass elektrische und elektronische
Geräte sowie Batterien und Akkus am Ende ihrer
Nutzungsdauer von Hausmüll getrennt zu entsorgen sind.
Wenn ein chemisches Symbol unterhalb des oben abgebildeten
Symbols erscheint, bedeutet dies, dass die Batterie bzw. der
Akku ein Schwermetall in einer bestimmten Konzentration
enthält. Dies wird wie folgt angegeben:

Hg: Quecksilber (0,0005 %), Cd: Cadmium (0,002 %),

Pb: Blei (0,004 %)
In der Europäischen Union gibt es unterschiedliche
Sammelsysteme für gebrauchte Elektrik- und Elektronikgeräte
einerseits sowie Batterien und Akkus andererseits.
Bitte entsorgen Sie dieses Gerät, Batterien und Akkus
vorschriftsmäßig bei Ihrer kommunalen Sammelstelle oder im
örtlichen Recycling-Zentrum.
Bitte helfen Sie uns, die Umwelt zu erhalten, in der wir leben!

Italiano

Questo prodotto MITSUBISHI ELECTRIC è stato progettato e
fabbricato con materiali e componenti di alta qualità, che possono
essere riciclati e/o riutilizzati.
Questo simbolo significa che i prodotti elettrici ed elettronici, le
batterie e gli accumulatori, devono essere smaltiti separatamente
dai rifiuti casalinghi alla fine della loro vita di servizio.
Se sotto il simbolo mostrato sopra è stampato un simbolo chimico, il
simbolo chimico significa che la batteria o l’accumulatore contiene
un metallo pesante con una certa concentrazione. Ciò viene
indicato come segue:

Hg: mercurio (0,0005%), Cd: cadmio (0,002%),

Pb: piombo (0,004%)
Nell’Unione Europea ci sono sistemi di raccolta differenziata per i
prodotti elettrici ed elettronici, le batterie e gli accumulatori usati.
Per disfarsi di questo prodotto, delle batterie e degli accumulatori,
portarli al centro locale di raccolta/riciclaggio dei rifiuti.
Aiutateci a conservare l’ambiente in cui viviamo!

Français

Votre produit Mitsubishi Electric est conçu et fabriqué avec des
matériels et des composants de qualité supérieure qui peuvent être
recyclés et/ou réutilisés.
Ce symbole signifie que les équipements électriques et électroniques,
les batteries et les accumulateurs, à la fin de leur durée de service,
doivent être éliminés séparément des ordures ménagères.
Si un symbole chimique est imprimé sous le symbole illustré
ci-dessus, il signifie que la batterie ou l'accumulateur contient une
certaine concentration de métal lourd. Elle sera indiquée comme
suit : Hg : mercure (0,0005%), Cd : cadmium (0,002%),

Pb : plomb (0,004%)
Dans l’Union Européenne, il existe des systèmes sélectifs de
collecte pour les produits électriques et électroniques, les batteries
et les accumulateurs usagés.
Nous vous prions donc de confier cet équipement, ces batteries et
ces accumulateurs à votre centre local de collecte/recyclage.
Aidez-nous à conserver l’environnement dans lequel nous vivons !

Les machines ou appareils électriques et électroniques contiennent
souvent des matières qui, si elles sont traitées ou éliminées de
manière inappropriée, peuvent s’avérer potentiellement
dangereuses pour la santé humaine et pour l’environnement.
Cependant, ces matières sont nécessaires au bon fonctionnement
de votre appareil ou de votre machine.
Pour cette raison, il vous est demandé de ne pas vous débarrasser
de votre appareil ou machine usagé avec vos ordures ménagères.

Español

Su producto MITSUBISHI ELECTRIC está diseñado y fabricado
con materiales y componentes de alta calidad que pueden ser
reciclados y/o reutilizados.
Este símbolo significa que el aparato eléctrico y electrónico, las
pilas, baterías y los acumuladores, al final de su ciclo de vida, se
deben tirar separadamente del resto de sus residuos domésticos.
Si hay un símbolo químico impreso debajo del símbolo mostrado
arriba, este símbolo químico significa que la pila, batería o el
acumulador contienen un metal pesado con cierta concentración.
Esto se indicará de la forma siguiente:

Hg: mercurio (0,0005%), Cd: cadmio (0,002%),

Pb: plomo (0,004%)
En la Unión Europea existen sistemas de recogida específicos para
productos eléctricos y electrónicos, pilas, baterías y acumuladores
usados.
Por favor, deposite los aparatos mencionados, las pilas, baterías y
acumuladores en el centro de recogida/reciclado de residuos de su
lugar de residencia local cuando quiera tirarlos.
i Ayúdenos a conservar el medio ambiente!

Português

O seu produto MITSUBISHI ELECTRIC foi concebido e produzido
com materiais e componentes de alta qualidade que podem ser
reciclados e/ou reutilizados.
Este símbolo significa que o equipamento eléctrico e electrónico, as
baterias e os acumuladores, no final da sua vida útil, devem ser
deitados fora separadamente do lixo doméstico.
Se houver um símbolo químico impresso por baixo do símbolo
mostrado acima, o símbolo químico indica que a bateria ou
acumulador contém metais pesados numa determinada
concentração. Isto aparecerá indicado da maneira seguinte:

Hg: mercúrio (0,0005%), Cd: cádmio (0,002%),

Pb: chumbo (0,004%)
Na União Europeia existem sistemas de recolha separados para
produtos eléctricos e electrónicos, baterias e acumuladores usados.
Por favor, entregue este equipamento, as baterias e os
acumuladores correctamente, no seu ponto local de
recolha/reciclagem.
Por favor, ajude-nos a conservar o ambiente em que vivemos!

Svenska

Denna produkt från MITSUBISHI ELECTRIC är designad och
tillverkad av material och komponenter med hög kvalitet som kan
återvinnas och/eller återanvändas.
Denna symbol betyder att förbrukade elektriska och elektroniska
produkter, batterier och ackumulatorer skall sorteras och hanteras
separat från hushållsavfall.
Om det finns en kemisk beteckning tryckt under ovanstående
symbol betyder det att batteriet eller ackumulatorn innehåller en
tungmetall med en viss koncentration. Detta anges på följande sätt:

Hg: kvicksilver (0,0005%), Cd: kadmium (0,002%),

Pb: bly (0,004%)
Inom den Europeiska Unionen finns det separata insamlingssystem
för begagnade elektriska och elektroniska produkter, batterier och
ackumulatorer.
Var vänlig lämna denna produkt, batterier och ackumulatorer hos
din lokala mottagningsstation för avfall och återvinning.
Var snäll och hjälp oss att bevara miljön vi lever i!

Dansk

Dit produkt fra MITSUBISHI ELECTRIC er designet og fremstillet
med kvalitetsmaterialer og komponenter, der kan genindvindes
og/eller genbruges.
Dette symbol viser, at elektrisk eller elektronisk udstyr, batterier og
akkumulatorer ikke må bortskaffes sammen med almindeligt
husholdningsaffald efter endt levetid.
Hvis der er trykt et kemisk symbol under symbolet ovenfor, betyder
det, at batteriet eller akkumulatoren indeholder en bestemt
koncentration af et tungmetal. Dette angives som følger:

Hg: kviksølv (0,0005 %), Cd: cadmium (0,002 %),

Pb: bly (0,004 %)
I EU er der særlige indsamlingsordninger for brugte elektriske og
elektroniske produkter, batterier og akkumulatorer.
Bortskaf udstyret, batterier og akkumulatorer korrekt på en lokal
affalds-/genbrugsplads.
Hjælp os med at bevare det miljø, vi lever i!

Norsk

For norske brukere:
Dette produktet fra MITSUBISHI ELECTRIC er konstruert og
produsert med materialer og komponenter av høy kvalitet, som kan
resirkuleres og/eller brukes om igjen.
Dette symbolet betyr at elektrisk og elektronisk utstyr, batterier og
akkumulatorer, ikke bør kasseres sammen med
husholdningsavfallet når de har nådd slutten av sin levetid.
Hvis det er trykt et kjemisk symbol under det symbolet som er vist
over, betyr det kjemiske symbolet at batteriet eller akkumulatoren
inneholder et tungmetall i en viss konsentrasjon. Dette vil vises som
følger:

Hg: kvikksølv (0,0005 %), Cd: kadmium (0,002 %),

Pb: bly (0,004 %)
I Norge finnes det egne innsamlingssystemer for brukte elektriske
og elektroniske produkter, batterier og akkumulatorer.

Kasser dette utstyret, batteriene og akkumulatorene ved den
lokale gjenbruks- eller resirkuleringsstasjonen.
Hjelp oss å bevare det miljøet vi lever i!

Suomi

Tämä MITSUBISHI ELECTRIC -tuote on suunniteltu ja valmistettu
korkealuokkaisista materiaaleista ja/tai osista, jotka voidaan
kierrättää ja käyttää uudelleen.
Tämä symboli tarkoittaa, että sähkö- ja elektroniikkalaitteet, paristot
ja akut täytyy niiden käyttöiän jälkeen hävittää erillään
talousjätteistä.
Jos yllä olevan symbolin alapuolelle on painettu kemiallinen symboli,
se tarkoittaa, että paristolla tai akulla on tietty raskasmetallipitoisuus.
Se ilmoitetaan seuraavasti:

Hg: elohopea (0,0005 %), Cd: kadmium (0,002 %),

Pb: lyijy (0,004 %)
Käytetyillä sähkö- ja elektroniikkalaitteilla, paristoilla ja akuilla on
Euroopan Yhteisössä omat keräysjärjestelmänsä.
Toimita tämä laite, paristot ja akut paikalliseen
jätehuolto-/kierrätyskeskukseen.
Auta meitä suojelemaan ympäristöä, jossa elämme!

Nederlands

Mitsubishi Electric producten zijn ontwikkeld en gefabriceerd uit
eerste kwaliteit materialen. De onderdelen kunnen worden
gerecycled en/of worden hergebruikt.
Het symbool betekent dat de elektrische en elektronische
onderdelen, batterijen en accu’s op het einde van de gebruiksduur
gescheiden van het huishoudelijk afval moeten worden ingezameld.
Wanneer er onder het bovenstaande symbool een chemisch
symbool staat gedrukt, betekent dit dat de batterij of accu zware
metalen in een bepaalde concentratie bevat. Dit wordt als volgt
aangeduid:

Hg: kwik (0,0005%), Cd: cadmium (0,002%),

Pb: lood (0,004%)
In de Europese Unie worden elektrische en elektronische producten,
batterijen en accu’s afzonderlijk ingezameld.
Breng deze apparatuur, batterijen en accu’s dan naar het
gemeentelijke afvalinzamelingspunt.
Help ons mee het milieu te beschermen!

Ελληνικά

Το προϊόν MITSUBISHI ELECTRIC που διαθέτετε είναι σχεδιασμένο
και κατασκευασμένο από υλικά και εξαρτήματα υψηλής ποιότητας,
τα οποία μπορούν να ανακυκλωθούν ή/και να χρησιμοποιηθούν
ξανά.
Το σύμβολο αυτό σημαίνει ότι ο ηλεκτρικός και ηλεκτρονικός
εξοπλισμός, οι μπαταρίες και οι συσσωρευτές, στο τέλος της
διάρκειας ζωής τους, θα πρέπει να απορριφτούν ξεχωριστά από τα
υπόλοιπα οικιακά απορρίμματά σας.
Αν έχει εκτυπωθεί ένα χημικό σύμβολο κάτω από το σύμβολο που
απεικονίζεται ανωτέρω, αυτό το χημικό σύμβολο σημαίνει ότι η
μπαταρία ή ο συσσωρευτής περιέχει ένα βαρύ μέταλλο σε ορισμένη
συγκέντρωση. Αυτό θα υποδεικνύεται ως ακολούθως:

Hg: υδράργυρος (0,0005%), Cd: κάδμιο (0,002%),

Pb: μόλυβδος (0,004%)

Στην Ευρωπαϊκή Ένωση υπάρχουν ξεχωριστά συστήματα
συλλογής για τα χρησιμοποιημένα ηλεκτρικά και ηλεκτρονικά
προϊόντα, τις μπαταρίες και τους συσσωρευτές.
Παρακαλούμε διαθέστε αυτόν τον εξοπλισμό, τις μπαταρίες και τους
συσσωρευτές στο τοπικό σας κοινοτικό κέντρο
συλλογής/ανακύκλωσης απορριμμάτων.
Βοηθήστε μας να προστατεύσουμε το περιβάλλον στο οποίο ζούμε!

0904874HK5201