Mitsubishi Electric FR-A7AD, FR-A720-55K, FR-A720-75K, FR-A740-55K, FR-A740-75K Instruction Manual
INVERTER
Plug-in option
FR-A7AD
INSTRUCTION MANUAL
High-speed analog output function
PRE-OPERATION
INSTRUCTIONS
1
Digital output function
INSTALLATION AND WIRING
PARAMETER LIST
HIGH-SPEED ANALOG OUTPUT
DIGITAL OUTPUT
2
3
4
5
Thank you for choosing this Mitsubishi Inverter plug-in option.
This Instruction Manual gives handling information and
precautions for use of this equipment. Incorrect handling might
cause an unexpected fault. Before using the equipment, please
read this manual carefully to use the equipment to its optimum.
Please forward this manual to the end user.
This section is specifically about
safety matters
Do not attempt to install, operate, maintain or inspect this
product until you have read through this Instruction Manual and
appended documents carefully and can use the equipment
correctly. Do not use this product until you have a full
knowledge of the equipment, safety information and
instructions.
In this Instruction Manual, the safety instruction levels are
classified into "WARNING" and "CAUTION".
Incorrect handling may cause
WARNING
CAUTION
The level may even lead to a serious
consequence according to conditions. Both instruction levels
must be followed because these are important to personal
safety.
CAUTION
hazardous conditions, resulting in
death or severe injury.
Incorrect handling may cause
hazardous conditions, resulting in
medium or slight injury, or may cause
only material damage.
SAFETY INSTRUCTIONS
1. Electric Shock Prevention
WARNING
• While power is ON or when the inverter is running, do not
open the front cover. You may get an electric shock.
• Do not run the inverter with the front cover or wiring cover
removed. Otherwise, you may access the exposed highvoltage terminals and charging part and get an electric shock.
• Even if power is OFF, do not remove the front cover except
for wiring or periodic inspection. You may accidentally touch
the charged inverter circuits and get an electric shock.
• Before wiring or inspection, power must be switched OFF. To
confirm that, LED indication of the operation panel must be
checked. (It must be OFF.) Any person who is involved in
wiring or inspection shall wait for at least 10 minutes after the
power supply has been switched OFF and check that there
are no residual voltage using a tester or the like. The
capacitor is charged with high voltage for some time after
power OFF, and it is dangerous.
• Any person who is involved in wiring or inspection of this
equipment shall be fully competent to do the work.
• The plug-in option must be installed before wiring. Otherwise,
you may get an electric shock or be injured.
• Do not touch the plug-in option or handle the cables with wet
hands. Otherwise you may get an electric shock.
• Do not subject the cables to scratches, excessive stress,
heavy loads or pinching. Otherwise you may get an electric
shock.
A-1
2. Injury Prevention
3) Usage
CAUTION
• The voltage applied to each terminal must be the ones
specified in the Instruction Manual. Otherwise burst, damage,
etc. may occur.
• The cables must be connected to the correct terminals.
Otherwise burst, damage, etc. may occur.
• Polarity must be correct. Otherwise burst, damage, etc. may
occur.
• While power is ON or for some time after power-OFF, do not
touch the inverter as they will be extremely hot. Doing so can
cause burns.
3. Additional Instructions
Also the following points must be noted to prevent an accidental
failure, injury, electric shock, etc.
1) Transportation and mounting
CAUTION
• Do not install or operate the plug-in option if it is damaged or
has parts missing.
• Do not stand or rest heavy objects on the product.
• The mounting orientation must be correct.
• Foreign conductive objects must be prevented from entering
the inverter. That includes screws and metal fragments or
other flammable substances such as oil.
2) Trial run
CAUTION
• Before starting operation, each parameter must be confirmed
and adjusted. A failure to do so may cause some machines to
make unexpected motions.
WARNING
• Do not modify the equipment.
• Do not perform parts removal which is not instructed in this
manual. Doing so may lead to fault or damage of the inverter.
CAUTION
•
When parameter clear or all parameter clear is performed, the
required parameters must be set again before starting
operations because all parameters return to the initial value.
• Static electricity in your body must be discharged before you
touch the product. Otherwise the product may be damaged.
4) Maintenance, inspection and parts replacement
CAUTION
• Do not test the equipment with a megger (measure insulation
resistance).
5) Disposal
CAUTION
• This inverter plug-in option must be treated as industrial
waste.
6) General instruction
Many of the diagrams and drawings in this Instruction Manual
show the inverter without a cover or partially open for
explanation. Never operate the inverter in this manner. The
cover must be reinstalled and Instruction manual of the inverter
must be followed when operating the inverter.
A-2
— CONTENTS —
1 PRE-OPERATION INSTRUCTIONS 1
1.1 Inverter Model ....................................................................................................................................1
1.2 Unpacking and Product Confirmation .............................................................................................2
1.2.1 Product confirmation.......................................................................................................................................2
1.3 Parts ....................................................................................................................................................3
1.4 Specifications.....................................................................................................................................4
2 INSTALLATION AND WIRING 5
2.1 Pre-Installation Instructions .............................................................................................................5
2.2 Installation Procedure .......................................................................................................................6
2.3 Wiring..................................................................................................................................................8
3 PARAMETER LIST 11
4 HIGH-SPEED ANALOG OUTPUT 12
4.1 Wiring Example ................................................................................................................................12
4.2 Terminals ..........................................................................................................................................13
4.3 Calibration procedure......................................................................................................................14
4.3.1 Calibration of voltmeter.................................................................................................................................14
4.3.2 Monitor setting..............................................................................................................................................17
4.3.3 Scale setting.................................................................................................................................................21
4.3.4 High-speed analog output filter setting.........................................................................................................21
4.4 Instructions ......................................................................................................................................22
I
5 DIGITAL OUTPUT 23
5.1 Terminals ..........................................................................................................................................23
5.2 Output Signal List ............................................................................................................................24
II
1 PRE-OPERATION INSTRUCTIONS
1.1 Inverter Model
The inverter model numbers of 55K and 75K stated in this Instruction Manual differ according to -NA, -EC,
-CH(T) versions. Refer to the following correspondence table for each inverter model. (Refer to the
Instruction Manual of each inverter for the inverter model.)
For example, "for the 75K or higher" indicates "for the FR-A740-01440-NA or higher" in the case of FRA740 of NA version.
NA EC CH
FR-A720-55K FR-A720-02150-NA ⎯⎯
FR-A720-75K FR-A720-02880-NA ⎯⎯
FR-A740-55K
FR-A740-75K
FR-A740-01100-NA
(FR-A760-00840-NA)
FR-A740-01440-NA
(FR-A760-01040-NA)
FR-A740-01800-EC FR-A740-55K-CHT
FR-A740-02160-EC FR-A740-75K-CHT
1
1
PRE-OPERATION INSTRUCTIONS
1.2 Unpacking and Product Confirmation
Take the plug-in option out of the package, check the product name, and confirm that the product is as you
ordered and intact.
This product is a plug-in option for the FR-A700 series manufactured in December 2011 or later.
Check the SERIAL number specified on the inverter rating plate or package.
SERIAL number check
z
Refer to Instruction manual of the inverter for the location of the rating plate.
Rating plate example
Symbol Year Month Control number
The SERIAL consists of one symbol, two characters indicating production year and month,
and six characters indicating control number.
The last digit of the production year is indicated as the Year, and the Month is indicated by
1 to 9, X (October), Y (November), or Z (December).
1 Z {{{{{{
SERIAL
1.2.1 Product confirmation
Check the enclosed items.
Plug-in option
......................................... 1
Mounting screw (M3 × 6mm)
.............. 2 (Refer to page 6.)
Hex-head screw for option
mounting (5.5mm)
...............1 (Refer to page 6.)
5.5mm
2
1.3 Parts
PRE-OPERATION INSTRUCTIONS
Terminal
block
Mounting
hole
Front view
Switch for manufacturer
setting
Do not change from initially-
set status (OFF: ).
Terminal layout
5
5
5
5
5
5
DD3
SW1
DA2
DA3
DA4
DA5
DD0
DD1
DD2
Mounting
hole
N
O
SW1
Rear view
Connector
Connect to the inverter
Mounting hole
option slot
(Refer to page 6)
1
3
PRE-OPERATION INSTRUCTIONS
1.4 Specifications
(1) Output signals
High-speed analog output (across the terminal 5’s and the terminals DA2 to DA5), 0VDC to ±10VDC
(12-bit output resolution)
Digital output (across the terminal 5’s and the terminals DD0 to DD3), 3V to 6V for HI, 0V to 2V for LOW
(2) Output accuracy (reference value)
±10% of the full-scale output value.
Depends on the output signal type.
(3) Meters used
DC voltmeter Full-scale ±10V (internal impedance 10kΩ or more)
Wiring length Maximum 30m
4
2 INSTALLATION AND WIRING
2.1 Pre-Installation Instructions
Make sure that the input power of the inverter is off.
CAUTION
With input power on, do not install or remove the plug-in option. Otherwise, the inverter and
plug-in option may be damaged.
Static electricity in your body must be discharged before you touch the product. Otherwise the
product may be damaged.
2
5
INSTALLATION AND WIRING
2.2 Installation Procedure
1)Remove the inverter front cover.
1)
Screw hole for
option mounting
Inverter side
option
connector
3)
Screw hole for
option mounting
(on earth plate)
Hex-head screw
for option mounting
REMARKS
• Remove a plug-in option after removing two screws on both left and right sides.
(When the plug-in option is mounted in the connector 3, it is easier to remove the plug-in option after removing a
control circuit terminal block.)
2)
4) Mounting
screws
2)Mount the hex-head screw for option
mounting into the inverter screw hole
(on earth plate). (size 5.5mm,
tightening torque 0.56N⋅m to 0.75N⋅m)
3)Securely fit the connector of the plug-in
option to the inverter connector along
the guides.
4)Securely fix the both right and left sides
of the plug-in option to the inverter with
the accessory mounting screws.
(Tightening torque 0.33N⋅m to
0.40N⋅m) If the screw holes do not lineup, the connector may not have been
plugged snugly. Check for loose
plugging.
6
Loading...