Global LCD Panel Exchange Center
www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
Revision Status for Products Specification
Products name COLOR TFT-LCD
Type name AA150XJ01
www.panelook.com
Rev. Description Rev.Date Prepared
First First Revision Apr.22,’03 M.Nishimura
Checked
Approved
T.Kawato
S.Yachi
Products Specification Rev.No.
ADPS - AA150XJ01- 01 - 01 --
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Vision Bank Corp.
15.0”XGA
TECHNICAL SPECIFICATION
AA150XJ01
MITSUBISHI / ADI
Date: Apr.22,’03
MITSUBISHI / ADI Confidential
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
(1/23)
AA150XJ01_02_01_First
www.panelook.com
Global LCD Panel Exchange Center
No. Item Page
www.panelook.com
CONTENTS
CONTENTS
CONTENTSCONTENTS
-- COVER 1
-- CONTENTS 2
1 OVERVIEW 3
2 ABSOLUTE MAXIMUM RATINGS 4
3 ELECTRICAL CHARACTERISTICS 4, 5, 6
4 INTERFACE PIN CONNECTION 7, 8
5 INTERFACE TIMING 9, 10, 11, 12
6 BLOCK DIAGRAM 13
7 MECHANICAL SPECIFICATION 14, 15
8 OPTICAL CHARACTERISTICS 16, 17
9 RELIABILITY TEST CONDITION 18
10 INSPECTION STANDARDS 19
11 HANDLING PRECAUTIONS FOR TFT-LCD MO DULE 20, 21, 22
12 REVISION STATUS 23
MITSUBISHI / ADI Confidential
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
(2/23)
AA150XJ01_02_01_First
www.panelook.com
Global LCD Panel Exchange Center
1. OVERVIEW
AA150XJ01 is 15.0” color TFT-LCD (Thin Film Transistor Liquid Crystal Display) modules
composed of LCD panel, driver ICs, control circuit, and backlight unit.
By applying 8 bit digital data, 1024 × 768, 16.7M-color images are displayed on the 15.0” diagonal
screen. Input power voltages are 5.0 V for LCD driving.
The type of data and control signals are digital, and 2 pixel data are transmitted per Typ. 32.5
MHz clock cycle.
General specifications are summarized in the following table:
ITEM SPECIFICATION
www.panelook.com
Display Area (mm)
Number of Dots
Pixel Pitch (mm)
Color Pixel Arrangement RGB vertical stripe
Display Mode Normally white TN
Number of Color 16.7 M(8 bits/color)
Brightness
Wide Viewing Angle Technology Optical Compensation Film
Viewing Angle -75~75° (H) -60~50° (V)
Surface Treatment Anti-glare and hard-coating 3H
Electrical Interface CMOS(VI = 3~5 V, 2 pixel / clock)
Optimum Viewing Angle(Contrast ratio) 6 o’clock
Module Size (mm)
Module Mass (g) 1070
304.1 (H) × 228.1 (V)
(15.0-inch diagonal)
1024 × 3 (H) × 768 (V)
0.297 (H) × 0.297 (V)
250 cd/m
320.0 (W) × 250.0 (H) × 12.5 (D)
2
（Typ.）
Backlight Unit CCFL, 2-tubes, edge-light
Sign “( )”represents preliminary value. Characteristic value without any note is typical value.
The LCD product described in this specification is designed and manufactured for the standard
use in OA equipment and consumer products, such as computers, communication equipment,
industrial robots, AV equipment and so on.
Do not use the LCD product for the equipment that require the extreme high level of reliability,
such as aerospace applications, submarine cables, nuclear power control systems and medical or
other equipment for life support.
ADI assumes no responsibility for any damage resulting from the use of the LCD product in
disregard of the conditions and handling precautions in this specification.
If customers intend to use the LCD product for the above items or other no standard items,
please contact our sales persons in advance.
MITSUBISHI / ADI Confidential
(3/23)
AA150XJ01_02_01_First
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
g
2. ABSOLUTE MAXIMUM RATINGS
ITEM SYMBOL MIN. MAX. UNIT
Power Supply Voltage for LCD VCC 0 7.0 V
Logic Input Voltage VI -0.5 6. 1 V
Lamp Voltage VL 0 2500 Vrms
Lamp Current IL 0 10.0 mArms
Lamp Frequency FL -- 100 kHz
www.panelook.com
Operation Temperature *) T
Storage Temperature *) T
op
stg
0 50 °C
-20 60 °C
[Note]
*) Top,Tstg
≤ 40°C : 90% RH max. without condensation
Top,Tstg > 40°C : Absolute humidity shall be less than the value of 90% RH at 40°C without
condensation.
3. ELECTRICAL CHARACTERISTICS
(1) TFT- LCD Ambient Temperature : Ta = 25°C
ITEM SYMBOL MIN. TYP. MAX. UNIT Remarks
Power Supply Voltages for LCD VCC 4.5 5.0 5.5 V *1)
Power Supply Currents for LCD ICC -- 300 500 mA *2)
Permissive Input Ripple Voltage VRP -- -- 100 mVp-p VCC = +5.0 V
Logic Input High VIH 2.2 3.3 5.5 V
Voltage Low VIL 0 -- 0.8 V
*1) Power and signals sequence:
t1
≤ 10 ms
0 < t2
0 < t3
0 < t4
≤ 10 ms
≤ 1 s
≤ 50 ms
1 s
≤ t5
200 ms
0
≤ t7
≤ t6
4.5V
LCD Power Supply
Lo
ic Signal
Backlight Power Supply
0.5V
Data: RGB DATA, DCLK, HD, VD, DENA
MITSUBISHI / ADI Confidential
VCC
4.5V
data
t2
t1
VL
t6 t7
t3
(4/23)
2.2V
0.5V
t4
t5
AA150XJ01_02_01_First
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
VCC-dip conditions:
1) When VCCMIN ≥ 3.6 V, td
2) When VCCMIN < 3.6 V
VCC-dip conditions should also follow the power and signals sequence.
td
*2) Typical current condition:
256- gray- bar-pattern
768 line mode
VCC = 5.0 V, f
= 48.4 kHz, fV= 60 Hz, f
H
www.panelook.com
10 ms
≤
VCC
4.5V
VCCMIN
CLK
= 32.5 MHz
(2) Backlight Ta = 25°C
ITEM SYMBOL MIN. TYP. MAX. UNIT Remarks
Lamp Voltage VL -- 600 -- Vrms IL = 7.0 mArms
Lamp Current IL 3.5 7.0 8.0 mArms *1)*4)
Lamp Frequency FL 40 -- 70 kHz *2)
1550 -- -- Vrms Ta = 0°C
Starting Lamp Voltage VS
1350 --
--
Vrms Ta = 25°C
*3), IL = 7.0 mArms,
Lamp Life Time LT -- 50000 -- h
Continuous
Operation
*1) Lamp Current measurement method (The current meter is inserted in low voltage line.)
CTL
CTH
LCD
Module
CTL
CTH
A
Power
A
Inverter
Supply
*2) Lamp frequency of inverter may produce interference with horizontal synchronous frequency,
and this may cause horizontal beat on the display. Therefore, please adjust lamp frequency,
and keep inverter as far from module as possible or use electronic shielding between inverter
and module to avoid the interference.
*3) Lamp life time is defined as the time either when the brightness becomes 50% of the initial
value, or when the starting lamp voltage does not meet the value specified in this table.
MITSUBISHI / ADI Confidential
(5/23)
AA150XJ01_02_01_First
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
*4) Please use the inverter which has symmetrical current wave form as follows,
The degree of unbalance: less than 10%
www.panelook.com
The ratio of wave height: less than
I
PH
I
PL
CURRENT WAVE FORM
±10%
2
IPH: High side peak
: Low side peak
I
PL
The degree of unbalance = |IPH - IPL| / Irms
The ratio of wave height =
(or IPL) / Irms
I
PH
100(%)
×
MITSUBISHI / ADI Confidential
(6/23)
AA150XJ01_02_01_First
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
4. INTERFACE PIN CONNECTION
(1) CN 1(Data Signal and Power Supply)
Used Connector: IL-FHR-BF40S-HF (JAE)
Pin No. Symbol Function
1 GND
2 VCC
3 VCC
4 RO 0 Red odd data(LS B)
5 RO 1 Red odd data
6 RO 2 Red odd data
7 RO 3 Red odd data
8 GND
9 RO 4 Red odd data
10 RO5 Red odd data
11 RO6 Red odd data
12 RO7 Red odd data(MSB)
13 GND
14 GO0 Green odd data(LSB)
15 GO1 Green odd data
16 GO2 Green odd data
17 GO3 Green odd data
18 GND
19 GO4 Green odd data
20 GO5 Green odd data
21 GO6 Green odd data
22 GO7 Green odd data(MSB)
23 GND
24 BO0 Blue odd data(LSB)
25 BO1 Blue odd data
26 BO2 Blue odd data
27 BO3 Blue odd data
28 GND
29 BO4 Blue odd data
30 BO5 Blue odd data
31 BO6 Blue odd data
32 BO7 Blue odd data(MSB)
33 GND
34 NC This pin should be open or GND.
35 HD Horizontal Sync
36 VD Vertical Sync
37 DENA Data enable
38 GND
39 DCLK Dot Clock
40 GND
www.panelook.com
MITSUBISHI / ADI Confidential
(7/23)
AA150XJ01_02_01_First
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
(2) CN 2 (Data signal)
Used Connector: IL-FHR-BF36S-HF (JAE)
Pin No. Symbol Function
2 TEST This pin should be open. Test signal output for only internal test
3 TEST This pin should be open. Test signal output for only internal test
4 TEST This pin should be open. Test signal output for only internal test
5 GND
6 GND
7 RE0 Red even data(LSB)
8 RE1 Red even data
9 RE2 Red even data
10 RE3 Red even data
11 GND
12 RE4 Red even data
13 RE5 Red even data
14 RE6 Red even data
15 RE7 Red even data(MSB)
16 GND
17 GE0 Green even data(LSB)
18 GE1 Green even data
19 GE2 Green even data
20 GE3 Green even data
21 GND
22 GE4 Green even data
23 GE5 Green even data
24 GE6 Green even data
25 GE7 Green even data(MSB)
26 GND
27 BE0 Blue even data(LSB)
28 BE1 Blue even data
29 BE2 Blue even data
30 BE3 Blue even data
31 GND
32 BE4 Blue even data
33 BE5 Blue even data
34 BE6 Blue even data
35 BE7 Blue even data(MSB)
36 GND
www.panelook.com
(3) CN 3, 4(Backlight)
Backlight-side connector: BHR-03VS-1(JST)
Inverter-side connector: SM02(8.0)B-BHS-1(JST)
Pin No. Symbol Function
1 CTH
3 CTL
[Note] VBLH-VBLL = VL
MITSUBISHI / ADI Confidential
VBLH（High Voltage）
VBLL（Low Voltage）
(8/23)
AA150XJ01_02_01_First
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
5. INTERFACE TIMING
(1) Timing Specifications
ITEM SYMBOL MIN. TYP. MAX. UNIT
www.panelook.com
DCLK
*1) *4)
DATA *1)
(R,G,B,DENA,
HD, VD)
Horizontal Active Time t
DENA
*3)
Vertical Back Porch t
HD
*2)*4)
Frequency f
Period t
Low Width t
High Width t
Set up time t
Hold time t
Horizontal Front Porch t
Horizontal Back Porch t
Vertical Active Time t
Vertical Front Porch t
Frequency f
Period t
Low Width t
CLK
CLK
WCL
WCH
DS
DH
HA
HFP
HBP
VA
VFP
VBP
H
H
WHL
30 32.5 40 MHz
25.0 30.8 33.3 ns
8 -- -- ns
8 -- -- ns
2.3 -- -- ns
7.3 -- -- ns
512 512 512 t
0 12 -- t
6 148 -- t
768 768 768 t
0 3 -- t
4 35 -- t
CLK
CLK
CLK
H
H
H
-- 48.4 62.5 kHz
16 20.7 --
1 68 -- t
μs
CLK
VD *2)
Frequency f
Period t
Low Width t
V
V
WVL
55 60 75 Hz
13.3 16.7 18.2 ms
1 6 -- t
[Note]
*1) DATA is latched at fall edge of DCLK in this specification.
*2) Polarities of HD and VD are negative in this specification.
*3) DENA (Data Enable) should always be positive polarity as shown in the timing
specification.
*4) DCLK should appear during all invalid period, and HD should appear during invalid period
of frame cycle.
H
MITSUBISHI / ADI Confidential
(9/23)
AA150XJ01_02_01_First
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
V
(2) Timing Chart
www.panelook.com
a. Pixel Timing Chart
DCLK
DATA
(R,G,B,ODD,EVEN),
DENA, HD , V D
b. Horizontal Timing Chart
DCLK
ODD DATA
Invalid Data
(R,G,B)
EVEN DATA
Invalid Data
(R,G,B)
t
HFP
t
HBP
t
WCH
t
DS
123
t
CLK
t
WCL
t
DH
First Data
4
2.2V
0.8V
2.2V
0.8V
5
6
t
HA
1021
1022
1023
1024
Invalid Data
Invalid Data
Last Data
DENA
t
WHL
HD
c. Vertical Timing Chart
HD
LINE DATA
t
VFP
DENA
D
tH=1/f
H
Invalid Data Invalid Data
t
VBP
t
WVL
12 7677683
t
VA
tV=1/f
V
MITSUBISHI / ADI Confidential
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
(10/23)
AA150XJ01_02_01_First
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
(3) Color Data Assignment
R DATA G DATA BDATA
COLOR R7 R6 R5 R4 R3 R2 R1 R0 G7 G6 G5 G4 G3 G2 G1 G0 B7 B6 B5 B4 B3 B2 B1 B0
BASIC
COLOR
RED
GREEN
BLUE
INPUT
DATA
BLACK
RED(255)
GREEN(255)
BLUE(255)
CYAN
MAGENTA
YELLOW
WHITE
RED(0)
RED(1)
RED(2)
RED(254)
RED(255)
GREEN(0)
GREEN(1)
GREEN(2)
GREEN(254)
GREEN(255)
BLUE(0)
BLUE(1)
BLUE(2)
BLUE(254)
BLUE(255)
MSB LSB MSB LSB MSB LSB
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
[Note]
*1) Definition of gray scale
Color (n) --- n indicates gray scale level.
Higher n means brighter level.
*2) Data
1:High, 0: Low
MITSUBISHI / ADI Confidential
(11/23)
AA150XJ01_02_01_First
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
(4) Data Mapping
D( 1, 1) D( 2, 1) --- D( X, 1) --- D(1023, 1) D(1024, 1)
D( 1, 2) D( 2, 2) --- D( X, 2) --- D(1023, 2) D(1024, 2)
¦ ¦ + ¦ + ¦ ¦
D( 1, Y) D( 2, Y) --- D( X, Y) --- D(1023, Y) D(1024, Y)
¦ ¦ + ¦ + ¦ ¦
D( 1,767) D( 2,767) --- D( X,767) --- D(1023,767) D(1024,767)
D( 1,768) D( 2,768) --- D( X,768) --- D(1023,768) D(1024,768)
www.panelook.com
MITSUBISHI / ADI Confidential
(12/23)
AA150XJ01_02_01_First
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
6. BLOCK DIAGRAM
TFT-LCD Module
CN2
CN1
Timing
Controller
Voltage Supply
for Gray Levels
and Vcom
DC/DC
Converter
Backlight
Source Driver
LCD Panel
Gate Driver
1024 X 3 X 768
Backlight CN4
CN3
BACKLIGHT
CCFL
CN3, 4
1
3
MITSUBISHI / ADI Confidential
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
(13/23)
AA150XJ01_02_01_First
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
7. MECHANICAL SPECIFICATIONS
(1)Front side
MITSUBISHI / ADI Confidential
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
(14/23)
AA150XJ01_02_01_First
(Unit:mm)
www.panelook.com
Global LCD Panel Exchange Center
(2)Rear side
www.panelook.com
[Note]
We recommend you referring to the detailed drawing for your design.
Please contact our company sales representative when you need the detailed drawing.
MITSUBISHI / ADI Confidential
(15/23)
AA150XJ01_02_01_First
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
(Unit: mm)
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
8. OPTICAL CHARACTERISTICS
Ta = 25°C, VCC = 5.0 V, Input Signals: Typ. Values shown in Section 5
ITEM SYMBOL CONDITION MIN. TYP. MAX. UNIT Remarks
Contrast Ratio CR
Luminance Normal Lw
Uniformity
ΔLw θ = φ = 0°
Response Time tr
Horizontal
Viewing Vertical
Angle Horizontal
Vertical
tf
φ CR ≥ 10
θ
φ CR ≥ 5
θ
θ = φ = 0°
θ = φ = 0°
θ = φ = 0°
θ = φ = 0°
--
--
300 450 -200 250 --
-- -- 30
-- 6 --
-- 19 --
--
-75∼75
-60∼50
--
-80∼80
-80∼70
--
--
--
--
Image Sticking tis 2 h -- -- 2 s
Red Rx 0.616 0.646 0.676
Ry 0.300 0.330 0.360
Color Green Gx 0.252 0.282 0.312
Coordinates Gy
θ = φ = 0°
0.560 0.590 0.620
Blue Bx 0.115 0.145 0.175
White Wx 0.283 0.313 0.343
By 0.030 0.060 0.090
Wy 0.299 0.329 0.359
[Note]
These items are measured using CS1000(MINOLTA) for color coordinates, EZContrast(ELDIM) for
viewing angle, and CS1000 or BM-5A(TOPCON) for others under the dark room condition (no
ambient light) after more than 30 minutes from turning on the lamp unless noted.
--
cd/m
%
ms
ms
°
°
°
°
--
2
*1)*3)
*2)*3)
*2)*3)
*3)*4)
*3)*4)
*3)
*3)
*3)
*3)
*5)
*3)
Condition: IL = 7.0 mArms, Inverter frequency: 60 kHz
*1) Definition of Contrast Ratio
CR=ON(White) Luminance / OFF(Black) Luminance: average of 5 points shown in a figure
below
*2) Definition of Luminance and Luminance Uniformity
Lw=ON (White) Luminance: average of 5 points shown in a figure below
ΔLw=[Lw(MAX)/Lw(MIN)-1] × 100
(1,1)
192
384
576
256 512 768
1
5
3
2
4
(1024,768)
MEASUREMENT POINT
MITSUBISHI / ADI Confidential
(16/23)
AA150XJ01_02_01_First
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
*3) Definition of Viewing Angle( θ , φ)
*4) Definition of Response Time
www.panelook.com
White
90%90%
Luminance
10%10% Black
tr
tf
*5) Image Sticking
Continuously display the test pattern shown in the figure below for two-hours. Then display a
completely white screen. The previous image shall not persist more than two seconds at 25°C.
Cols 510-514
White
Area
Rows 382-386
Black
Lines
TEST PATTERN FOR IMAGE STICKING TEST
MITSUBISHI / ADI Confidential
(17/23)
AA150XJ01_02_01_First
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
9. RELIABILITY TEST CONDITION
(1) Temperature and Humidity
TEST ITEM CONDITIONS
HIGH TEMPERATURE 40°C, 90% RH, 240h
HIGH HUMIDITY OPERATION (No condensation)
HIGH TEMPERATURE OPERATION 50°C, 240 h
LOW TEMPERATURE OPERATION 0°C, 240 h
www.panelook.com
THERMAL SHOCK
(Non-Operation)
HIGH TEMPERATURE STORAGE 60°C, 240 h
LOW TEMPERATURE STORAGE -20°C, 240 h
(2) Shock & Vibration
ITEM CONDITIONS
Shock level: 980 m/s
SHOCK Waveform: half sinusoidal wave, 2 ms
(NON-OPERATION) Number of shocks: one shock input in each direction of three mutually
Perpendicular axes for a total of six shock inputs
Vibration level: 9.8 m/s
Waveform: sinusoidal
VIBRATION Frequency range: 5 to 500 Hz
(NON-OPERATION) Frequency sweep rate: 0.5 octave /min
Duration: one sweep from 5 to 500 Hz in each of three mutually
2
(100 G）
BETWEEN -20°C (1h) and 60°C(1h),
5 CYCLES
2
(1.0 G）zero to peak
perpendicular axis(each x,y,z axis: 1 hour, total 3 hours)
(3) Judgment standard
The judgment of the above tests should be made as follow:
Pass: Normal display image with no obvious non-uniformity and no line defect.
Partial transformation of the module parts should be ignored.
Fail: No display image, obvious non-uniformity, or line defects.
MITSUBISHI / ADI Confidential
(18/23)
AA150XJ01_02_01_First
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
10. INSPECTION STANDARDS
Inspection condition is as follows:
Viewing distance is approximately 35 cm.
Viewing angle is normal to the LCD panel.
Ambient temperature is approximately 25°C.
Ambient light is from 300 to 500 lx.
Bright Dot is defined as follows:
Visible through 5% transmission ND filter under the condition that black image (color 0) is on
the display.
DEFECT TYPE LIMIT
SCRATCH
DENT
VISUAL
DEFECT
ELECTRICAL
DEFECT
*1) W: width,L: length,φ : diameter,N: number
*2) DEFINITION OF ADJACENT
BLACK SPOT
BUBBLE
BRIGHT DOT
DARK DOT
TOTAL DOT
TWO ADJACENT DOT
BRIGHT DOT
DARK DOT
THREE OR MORE
ADJACENT DOT
DISTANCE BETWEEN
DEFECTS
BRIGHT DOT
DARK DOT
LINE DEFECT NOT ALLOWED
LINT
www.panelook.com
0.01 mm < W ≤ 0.05 mm
L ≤ 10 mm
0.01 mm < W
10 mm < L
0.05 mm < W N = 0
0.2 mm < φ≤ 0.4 mm N ≤ 4
0.4 mm < φ
0.2 mm < φ ≤ 0.4 mm N ≤ 5
0.4 mm < φ
L ≤ 3 mm
W ≤ 0.1 mm
3 mm < L
W ≤ 0.1 mm
0.1 mm < W
ACCORDING TO
BLACK SPOT
N ≤ 4
N ≤ 4
N ≤ 4
≤ 2 PAIRS
≤ 2 PAIRS
NOT ALLOWED
≥ 15 mm
≥ 15 mm
N ≤ 4
N = 0
N = 0
N = 0
N ≤ 4
N = 0
GRBRGB RGB
Defective Dot
GRBRGB RGB
Adjacent Dots
GRBRGB RGB
The defects that are not defined above and considered to be problem shall be reviewed and discussed
by both parties.
MITSUBISHI / ADI Confidential
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
(19/23)
AA150XJ01_02_01_First
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
11. HANDLING PRECAUTIONS FOR TFT-LCD MODULE
Please pay attention to the followings in handling TFT-LCD products;
(1) ASSEMBLY PRECAUTION
a. Please mount the LCD module by using mounting hole with a screw clamping torque less than
0.5 Nm. Please do not bend or wrench the LCD module in assembling. Please do not drop, bend
or twist the LCD module in handling. Please mount the invertor circuit board by using
mounting hole of rear side with a screw clamping torque less than 0.2 Nm.
b. Please design display housing in accordance with the following guide lines.
(a) Housing case must be designed carefully so as not to put stresses on LCD all sides and not to
wrench module. The stresses may cause non-uniformity even if there is no non-uniformity
statically.
(b) Keep sufficient clearance between LCD module back surface and housing when the LCD
module is mounted. Approximately 1.0mm of the clearance in the design is recommended
taking into account the tolerance of LCD module thickness and mounting structure height on
the housing.
(c) When some parts, such as, FPC cable and ferrite plate, are installed underneath the LCD
module, still sufficient clearance is required, such as 0.5mm. This clearance is, especially, to
be reconsidered when the additional parts are implemented for EMI countermeasure.
(d) Design the inverter location and connector position carefully so as not to give stress to lamp
cable, or not to interface the LCD module by the lamp cable.
(e) Keep sufficient clearance between LCD module and the others parts, such as inverter and
speaker so as not to interface the LCD module. Approximately 1.0mm of the clearance in the
design is recommended.
c. Please do not push or scratch LCD panel surface with anything hard. And do not soil LCD panel
surface by touching with bare hands. (Polarizer film, sur f ace of LCD panel is easy t o be f law ed. )
d. Please do not press any parts on the rear side such as source TCP, gate TCP, control circuit
board and FPCs during handling LCD module. If pressing rear part is unavoidable, handle the
LCD module with care not to damage them.
e. Please wipe off LCD panel surface with absorbent cotton or soft cloth in case of it being soiled.
f. Please wipe off drops of adhesives like saliva and water on LCD panel surface immediately. They
might damage to cause panel surface variation and color change.
g. Please do not take a LCD module to pieces and reconstruct it. Resolving and reconstructing
modules may cause them not to work well.
h. Please do not touch metal frames with bare hands and soiled gloves. A color change of the metal
frames can happen during a long preservation of soiled LCD modules.
i. Please handle metal frame carefully to avoid getting hurt because edge of metal frame is very
sharp.
MITSUBISHI / ADI Confidential
(20/23)
AA150XJ01_02_01_First
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
j. Please pay attention to handling lead wire of backlight so that it is not tugged in connecting with
inverter.
k. Please connect the metal frame of LCD module to GND in order to minimize the effect of
external noise and EMI.
l. Be sure to connect the cables and the connectors correctly.
(2) OPERATING PRECAUTIONS
a. Please be sure to turn off the power supply before connecting and disconnecting signal input
cable.
b. Please do not change variable resistance settings in LCD module. They are adjusted to the most
suitable value. If they are changed, it might happen LCD does not satisfy the characteristics
specification.
www.panelook.com
c. LCD backlight takes longer time to become stable of radiation characteristics in low temperature
than in room temperature.
d. A condensation might happen on the surface and inside of LCD module in case of sudden change
of ambient temperature.
e. Please pay attention not to display the same pattern for very long time. Image might stick on
LCD. Even if image sticking happens, it may disappear as the operation time proceeds.
f. Please obey the same safe instructions as ones being prepared for ordinary electronic products.
(3) PRECAUTIONS WITH ELECTROSTATICS
a. This LCD module use CMOS-IC on circuit board and TFT-LCD panel, and so it is easy to be
affected by electrostatics. Please be careful with electrostatics by the way of your body
connecting to the ground and so on.
b. Please remove protection film very slowly from the surface of LCD module to prevent from
electrostatics occurrence.
(4) STORAGE PRECAUTIONS
a. Please do not leave the LCDs in the environment of high humidity and high temperature such
as 60°C90% RH.
b. Please do not leave the LCDs in the environment of low temperature; below -20°C.
(5) SAFETY PRECAUTIONS
a. When you waste damaged or unnecessary LCDs, it is recommended to crush LCDs into pieces
and wash them off with solvents such as acetone and ethanol, which should later be burned.
MITSUBISHI / ADI Confidential
(21/23)
AA150XJ01_02_01_First
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
b. If any liquid leaks out of a damaged glass cell and comes in contact with the hands, wash off
thoroughly with soap and water.
c. Be sure to turn off the power supply when inserting or disconnecting the cable.
d. Inverter should be designed carefully so as not to keep working in case of detecting over current
or open circuit on the lamp.
(6) OTHERS
a. A strong incident light into LCD panel might cause display characteristics changing inferior
because of polarizer film, color filter, and other materials becoming inferior. Please do not
www.panelook.com
expose LCD module direct sunlight and strong UV rays.
b. Please pay attention to a panel side of LCD module not to contact with other materials in
preserving it alone.
c. For the packaging box, please pay attention to the followings;
(a) Packaging box and inner case for LCD are designed to protect the LCDs from the damage or
scratching during transportation. Please do not open except picking LCDs up from the box.
(b) Please do not pile them up more than 5 boxes. (They are not d esigned so.) A nd please do not
turn over.
(c) Please handle packaging box with care not to give them sudden shock and vibrations. And
also please do not throw them up.
(d) Packaging box and inner case for LCDs are made of cardboard. So please pay attention not
to get them wet. (Such like keeping them in high humidity or wet place can occur getting
them wet.)
MITSUBISHI / ADI Confidential
(22/23)
AA150XJ01_02_01_First
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
12. REVISION STATUS
Rev.
First First Revision Apr.22,’03 M.Nishimura
Description Date Prepared Checked
Approved
T.Kawato
S.Yachi
MITSUBISHI / ADI Confidential
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
(23/23)
AA150XJ01_02_01_First
www.panelook.com
Loading...