Mitsubishi A1S62TCRTBW-S2, A1S62TCRT-S2, A1S62TCTT-S2, A1S62TCTTBW-S2 User Manual

Thank you for purchasing the Mitsubishi general-purpose
programmable controller MELSEC-A series.

Prior to use, please read this manual thoroughly and
familiarize yourself with the product.

z

zz

z SAFETY PRECAUTIONS z

zz

z

(Read these precautions before using.)

When using Mitsubishi equipment, thoroughly read this manual and
the associated manuals introduced in the manual. Also, pay careful
attention to safety and handle the module properly.

These precautions apply only to Mitsubishi equipment. Refer to the
CPU module user's manual for a description of the PC system safety
precautions.

These zSAFETY PRECAUTIONSz classify the safety precautions
into two categories: "DANGER" and "CAUTION".

Procedures which may lead to a dangerous
condition and cause death or serious injury if not
carried out properly.

Procedures which may lead to a dangerous
condition and cause superficial to medium
injury, or physical damage only, if not carried out
properly.

Depending on circumstances, procedures indicated by

CAUTION

may also be linked to serious results.
In any case, it is important to follow the directions for usage.
Store this manual in a safe place so that you can take it out and read

it whenever necessary. Always forward it to the end user.

[Design precautions]

DANGER

z Configure a safety circuit external to the PC, so that the entire system

operates safety even if there is an external power error or if the PC is
malfunctioning.

CAUTION

z Do not bu ndle, or near the control cables and communicati on cables

with the main circuit and power cables. Keep them at least 100mm
(3.94inc h) away from such cables. N oise may cause malfuncti on.

[Installation precautions]

CAUTION

z Use the PC in the env iro nme nt g i ven in the ge ner a l spec if ica ti o ns of

the this manual. Using the PC outside the range of the general
specifications may result in electric shock, fire or malfunctioning. or
may damage or degrade the module.

z Insert the tabs at th e bot tom of th e mod ul e int o th e mou nt ing ho l es in

the base module before installing the module, and after tightening the
module fixing screws with specified torque. If the connector is not
property installed and tightened. If may result in malfunctioning, failure
or cause the module to lam out.

Tightening the screws too far may cause damage to the screw and/or

the module, resulting in fall out, short circuit or malfunctions.

z Do not direct ly touc h t h e modu le ’ s conduc t iv e part s o r el ect ro nic

components. Doing so could cause malfunction or fa ilu re i n t he
module.

z Insert the wire breakage detection connector installation screw into the

mounting holes in the module, and after tightening the connector
installation screw with specified toque. If the connect or is not pro perty
installed and tightened, it may result in error detetion of wire breakage.

[Wiring precautions]

CAUTION

z Be sure to ground the shield wire with a special PC ground of Type III

or above. Not do ing so co uld r esu lt i n malf un ct io n.

z When wiring in th e P C, be su re t hat it is don e cor r ect l y by chec k ing t he

product's rated voltage and the terminal layout. Connecting a power
supply that is different from the rating or incorrectly wiring the product
could result in fire or failure.

z Tighten the termina l s crews with s pecified torque. Loose t erminal

screws may cause a short circuit, fire, or m alfu nct ion.

Tighteni ng the terminal screws too far may cause damage to the screw

and/or the module, resulting in short ci rc uit, o r m alfu nct ions.

z Be sure that cuttings, wire chips, or ot her fo rei gn matt e r do not e nt er

the modul e. Foreign matt er may start a fire or ca use failure or
malfunctions.

z Be sure to fix communication cables and power cables leading from

the modul e by placing them in the d uc t or clamping them. Cabl es not
placed in the duct or without clamping may hang or shift, allowing them
to be accident al l y pul led, whic h may res ult i n a modu le ma lf unc t ion
and cable damage.

z When det ac hing the comm unication cable from t he module, do not pull

the cable portion. For cables with connectors, hold the connector at
the junction to the module, then detach it. For cables wit hout
connectors, first loosen the screw at th e ju nct ion, t h en detach t o th e
cable. Pul ling the c abl e po rt ion whi le it is con nec t ed to th e mod ul e
may cause a m alfunction or damage to the module and cable.

[Starting and maintenance precautions]

CAUTION

z Do not touch the terminal while the power is on.
It may cause malfunction.
z Make sure to switch all phases of the external power supply off before

cleaning or re-tightening the terminal screws. If you do not switch off
the external power supply, it will cause failure or malfunction of the
module.

z Never disassemble or modify the module. This may cause failure,

malfunctioning, injury and/or fire.

z Make sure to switch all phases of the external power supply off before

mounting or r emov i ng t he m od ul e. I f y ou d o not s witc h of f t he e xt ern al
power supply, it will cause failure or malfunction of the module.

[Disposal precaution]

CAUTION

z When dis posing of this product, handle it as i ndustrial was te.

DANGER

CAUTION

A1S62TCRT-S2 Heating-Cooling

Temperature Control Module

A1S62TCRTBW-S2 Heating-Cooling

Temperature Control Module with Wire

Breakage Detection Function

Mitsubishi General-Purpose Programmable Controller

User’s Manual

(Hardware)

C 1997 MITSUBISHI ELECTRIC CORPORATION

Type A1S62TCRT-U-HW-E
Type

Code

13JL33

IB(NA)-66801-C(0210)MEE

About This Manual

The following product manuals are available. Please use this table as
a reference to request the appropriate manual as necessary.

Detailed manual

Manual name

Manual No.

(Model Code)
A1S62TCRT-S2 Heating-Cooling Temperature Control Module
A1S62TCRTBW-S2 Heating-Cooling Temperature Control
Module with Wire Breakage Detection Function User's Manual

SH-3644
(13JL36)

Please read A1S62TCRT-S2 Heating-Cooling Temperature Control Module
A1S62TCRTBW-S2 Heating-Cooling Temperature Control Module with Wire
Breakage Detection Function User's Manual (Detailed edition) when using this
unit.

1. General Description

This user's manual describes the specification, name of each part,
wiring, etc. of the A1S62TCRT-S2 Heating-Cooling Temperature Control
Module (Hereafter abbreviated as A1S62TCRT-S2 ) A1S62TCRTBW-S2
Heating-Cooling Temperature Control Module with Wire Breakage
Detection Function (Hereafter abbreviated as A1S62TCRTBW-S2)
A1S62TCRT-S2 and A1S62TCRTBW-S2 abbreviated as A1S62TC.
After unpacking, confirm that there is the following products.

Item

A1S62TCRT-S2

Main body

A1S62TCRTBW-S2

Main body

A1S62TCRT-S2 1 -

A1S62TCRTBW-S2 - 1

2. Performance Specification

The A1S62TC performance specification is indicated in Table 2.1.

Table 2.1 A1S62TC performance specification

Specification

Item

A1S62TCRT-S2 A1S62TCRTBW-S2
Control output Transistor output
Temperature input points 2-channel/module
Supported platinum tem pe rat ur e­measuring resistor

Refer to Table 2.2.

Ambient temperature:
23

5

Full scale ( 0.3%) 1 digit*1

Specification
accuracy

Ambient temperature:
0 to 55

Full scale ( 0.7%) 1 digit*1

Sampling period

0.5s/2-channel (It is not connected with the

number of channels used)
Heating control output period
Cooling control output period

1 to 100s
Sensor current 0.25mA

Allowable input wire resistor effects

Less than 20Ω
Input filter 0 to 100s (0: input filter off)
Sensor compensation value setting -50.00 to 50.00%
Operation when sensor input is
disconnected

Upscale processing
Temperature control method PID on/off pulse

PID constant setting Auto-tuning setting is possible
Heating proportional band
(Ph)
Cooling proportional band
(Pc)

0.1 to 1000.0%

Integral time (I) 1 to 3600s

PID
constant
range

Derivative time (D) 0 to 3600s (0: PI control)

Set value setting range

Within the temperature range set by the

platinum temperature-measuring resistor

to be used.
Cooling method setting Air cooling/water cooling

Output signal ON/OFF pulse
Rated load voltage 10.2 to 30.0VDC (peak voltage : 30.0VDC)

Maximum load current

0.1A/1 point

0.4A/common
Max i mu m i nr u sh c ur r en t 0.4A 10ms
Maximum current when
OFF

Less than 0.1mA

Maximum voltage drop
when ON

1.0VDC (TYP) 0.1A

2.5VDC (MAX) 0.1A

Transistor
output

Response time

OFF

ON: Less than 2ms

ON

OFF: Less than 2ms (resistor load)

Insulation method

Between the input and grounding:
transformer insulation
Between the input and channel:
transformer insulation

Table 2.1 A1S62TC performance specification (continued)

Specification

Item

A1S62TCRT-S2 A1S62TCRTBW-S2

Current sensor

URD manufactured
current sensor*2
CTL-12-S36-8
(0.0 to 100.0A)
CTL-6-P-H
(0.00 to 20.00A)
(Former mode l,
CTL-6-P is also
applicable.)

Input method

Multiplex method
A/D conversion

Heater wire
breakage
disconnection
specification

Number of alert
delays

-

3 to 255

I/O occupied points Special 32 points
Connection terminal 20 po ints terminal block
Supported cable size (mm) [inch] 0.7 5 to 1.5 [0 .0 3 0 t o 0 .0 5 9]
Supported solder-less terminal R1.25-3, 1.25-YS3, RAV1.25-3, V1.25-YS3A
Internal consumed current (5VDC)
[A]

0.19 0.28

Weight (kg) [lb] 0.25 [0.55] 0.28 [0.62]

For the noise resistance, dielectric withstand voltage, and insulation
resistance for the PC system which uses this module, refer to the power
module specification found in the CPU Module User’s Manual.

*1: “

1 digit” error depends on the input range.

For setting unit of 1

, 1 For setting unit of 0.1 , 0.1

*2: Only the URD International, Ltd. current sensor can be used.

Sales channels for current sensors manufactures by URD
International Ltd. are listed as follows:

U.S.A. Julia Industries Inc.

Tel:[phone]

BRAZIL Ananda Industial Lt da.

Tel:[phone]
UNITED
KINGDOM Omni Components

Tel:[phone]
GERMANYAllied Electronics Gm bH

Tel:[phone]
FRANCE Diltronic S.A.

Tel:[phone]
ITALY ELNET s.n.c.

Tel:[phone]

KOREA Joyang Trading Co.

Tel:[phone]
Sewon Tech Co.,Ltd.
Tel:[phone]
Keum Ho Corporation
Tel:[phone]

HONG-KONG Weltronics Components Ltd.

Tel:[phone]

TAIWAN Tope Co.,Ltd.

Tel:[phone]

INDIA AmtechElectronics PVT.Ltd.

Tel:[phone]

Table 2.2 The types of supported platinum temperature-measuring

resistor and the measured temperature range

°F

Platinum

temperature-

measuring

resistor

Measured

temperature

range

Data

resolution

Measured

temperature range

Data

resolution

-300 to 1100 1

Pt 100

-200.0 to 600.0

-200.0 to 200.0

0.1

-300.0 to 300.0 0.1

-300 to 900 1

JPt100

-200.0 to 500.0

-200.0 to 200.0

0.1

-300.0 to 300.0 0.1

For the general specifications, refer to the User’s Manual for the PC
CPU used.