Page 1
Operator’s Manual
user manual, maintenance instructions and spare parts
650DX / 750DX Premium+ Hedgetrimmer
www.mitox.co.uk
Read this manual carefully before operating the machine
Original Instructions Version June 16
650DX+/750DX+_080616
Page 2
650DX / 750DX Premium+ Hedgetrimmer
2
Original Instructions Version June 16
650DX+/750DX+_080616
Component Location
1. Front handle
2. Fuel tank
3. Starter
4. Rear handle
5. Throttle lever
PRODUCT DESCRIPTION
This Hedgetrimmer is a 2 stroke fast running power tool and is designed to be used in a domestic
application for trimming new growth on hedges.
1.
2.
3.
4.
5.
6.
7.
8.
9.
6. Ignition switch
7. Muer
8. Blade
9. Blade guard
Page 3
650DX / 750DX Premium+ Hedgetrimmer
3
Original Instructions Version June 16
650DX+/750DX+_080616
Warnings in the Manual
This mark indicates instructions which must be followed in order to prevent accidents which could
lead to serious bodily injury or death.
This mark indicates instructions which must be followed or it leads to mechanical failure,
breakdown, or damage.
This mark indicates hints or useful directions in the use of the product.
Safety Symbols
(1) Read operator’s instruction book before operating this machine.
(2) Appropriate ear, eye, and head protection must be worn.
(3) Handling this machine improperly could result in accidents causing
serious injury or death. Read this manual carefully and practice
using the hedgetrimmer until you are fully acquainted with all
operations and have learned to use it correctly.
(4) This is extremely sharp and can easily cause cuts.
(5) Directive 2000-14/CE. Guaranteed noise levels.
(6) Danger: risk of exhaust fumes intoxication.
IMPORTANT
!
NOTE
Page 4
650DX / 750DX Premium+ Hedgetrimmer
4
Original Instructions Version June 16
650DX+/750DX+_080616
Taking Care of Warning Labels
Always keep warning labels clean and free of scratches, which might make them illegible or
dicult to read. If the warning labels provided with your hedgetrimmer become damaged, peel
o, or otherwise become illegible or dicult to read, order new labels from the authorised
servicing dealer and replace the damaged labels. When applying new labels, first wipe away any
dirt and dry the surface before applying the new label in the same place as the original label.
Explanation of Symbols on the Machine
For safe operation and maintenance, symbols are carved in relief on the machine:•
FUEL TANK
Fuel tank 2 stroke mix
Position: Fuel cap
CHOKE OPERATION
Starting mode when the engine is hot (choke o).
Position: Air cleaner cover.
Starting mode when the engine is cold (choke on).
Position: Air cleaner cover.
Safety Precautions
Introduction
Read this Owner/Operator Manual carefully. Be sure you understand how to operate this
hedgetrimmer properly before you use it. Failure to do so could result in serious injury.
Page 5
650DX / 750DX Premium+ Hedgetrimmer
5
Original Instructions Version June 16
650DX+/750DX+_080616
Keep this manual handy so that you may refer to it later whenever any questions arise. Also note
that you are able to contact the dealer from whom you purchased the product for assistance.
Always include this manual when selling, lending, or otherwise transferring the ownership of this
product.
This product has been designed to be used as a hedge trimmer power tool as described
previously and it should never be used for any other purpose; doing so could result in unforeseen
accidents and injuries occurring. Only approved Mitox accessories should be used with this
product.
This hedgetrimmer is equipped with extremely sharp blades, always wear sturdy gloves when
handling the blades and fit the safety guards when not in use.
When using this hedgetrimmer for the first time, take the hedge trimmer to a wide, clear, open
space, start the engine, and practice handling the hedge trimmer until you are sure that you will
be able to handle it properly in actual operation.
You should never use this hedgetrimmer when under the influence of alcohol, suering from
exhaustion or lack of sleep, suering from drowsiness as a result of having taken medicine, or at
any other time when your judgment might be impaired or that you might not be able to operate
the hedgetrimmer properly and in a safe manner.
Never allow children or anyone unable to fully understand the directions given in this manual to
use this hedgetrimmer.
When planning your work schedule, allow plenty of time to perform the work and allow plenty of
time for rest. Limit the amount of time you continuously use the hedgetrimmer to 30~40 minutes
per session, and take 10~20 minutes of rest between work sessions. Also try to keep the total
amount of work performed in a single day to 2 hours.
Avoid running the engine indoors, the exhaust gases contain harmful carbon monoxide.
Page 6
650DX / 750DX Premium+ Hedgetrimmer
6
Original Instructions Version June 16
650DX+/750DX+_080616
Never use the Hedgetrimmer in conditions as described
below:
When the ground is slippery or when other conditions exist which might make it dicult to
maintain a steady posture while using the hedgetrimmer.
At night, at times of heavy fog, or at any other times when your field of vision is limited and it
would be dicult to gain a clear view of the area where the hedgetrimmer is to be used.
In heavy rain, during lightning storms, at times of strong or gale-force winds, or at any other
times when weather conditions might make it unsafe to use this product.
Lack of sleep, tiredness, or physical exhaustion results in lower attention spans, and this in turn
can lead to accidents and injury.
Work Clothing and Safety Equipment
When using the product, you should wear proper clothing and protective equipment.
• Helmet
• Protection goggles or face protector
• Ear protectors
• Thick work gloves
• Non-slip sole work boots
Safety and Operation
This hedge trimmer is equipped with very sharp blades, and when used incorrectly the blades can
be extremely dangerous.
Page 7
650DX / 750DX Premium+ Hedgetrimmer
7
Original Instructions Version June 16
650DX+/750DX+_080616
Improper handling can cause accidents which may in turn lead to serious injury or death. For this
reason, you should always be careful to adhere to the following instructions when using your
hedgetrimmer. Never hold the hedge trimmer in a way in which the blades are pointing towards
someone else.
Never allow the blades to come into contact with your body.
Always turn o the engine before adjusting the hedgetrimmer, removing branches which have
become stuck in the blades, or at any other time when coming into close proximity with the
blades.
Always wear thick work gloves when adjusting the hedgetrimmer.
Always place the blade cover provided over the blades when not in use.
Falling branches may fall onto the operator’s body or head, resulting in injuries, scratches and
cuts, and for this reason you should always wear a helmet when operating the hedgetrimmer.
Safe Handling of Fuel
The engine of the hedge trimmer is designed to run on a two-stroke oil/fuel mixture. This fuel
is highly flammable, never store cans of fuel or refill the fuel tank in any place where there is a
source of heat or fire which might ignite the fuel.
Do not smoke whilst operating the hedge trimmer or refilling, keep lit cigarettes away from the
hedge trimmer at all times.
When refilling the fuel tank always stop the engine first and carefully make sure that there are no
sparks or open flames anywhere nearby before refuelling.
If any fuel spillage occurs during refuelling, use a dry rag to wipe any fuel which has been spilled
onto the hedgetrimmer before starting the engine.
After refuelling, screw the fuel cap back tightly onto the fuel tank and carry the hedgetrimmer to a
spot 5 metres or more away from where it was refuelled before starting the engine.
Page 8
650DX / 750DX Premium+ Hedgetrimmer
8
Original Instructions Version June 16
650DX+/750DX+_080616
Before Operating the Hedgetrimmer
Before beginning work, carefully check the work area and remove any obstacles.
Within a perimeter of 15 metres of the work area should be considered a hazardous area into
which no-one should enter while the hedgetrimmer is being used, and when necessary this area
should be marked with a warning rope, warning signs, or other forms of warning.
When work is to be performed simultaneously by two or more operators, care should also be
taken to constantly look around to check the presence and locations of other operators within the
work area to maintain a safe distance between each operator.
Before beginning work, each component of the hedgetrimmer should be checked to make sure
that it is in proper working order, make sure that there are no loose screws or bolts, fuel leaks,
ruptures, dents, or any other problems which might interfere with safe operation. Be especially
careful to check that there is no damage to the blades.
Keep all parts of your body away from the hedgetrimmer blades when the engine is running.
Before Starting the Engine
Carefully check the work area to make sure that no obstacles exist within a perimeter of 15
metres around the hedge trimmer before starting the engine.
To start the engine, place the hedgetrimmer onto the ground in a flat clear area and hold it firmly
in place to ensure that neither the blades nor the throttle come into contact with any obstacles
when the engine starts.
After starting the engine, make sure that the blades stop moving when the throttle trigger is
released (idle). If the blades continue to move when the engine is at idle, adjust the idle screw
on the carburettor to a point where the blades stop moving, if this cannot be achieved, take the
hedgetrimmer to your authorised servicing dealer for adjustment.
Page 9
650DX / 750DX Premium+ Hedgetrimmer
9
Original Instructions Version June 16
650DX+/750DX+_080616
Avoid Noise Problems
Check and follow the local regulations for sound levels and hours of operation for garden
machinery.
In general, operate hedgetrimmers between 8 am and 5 pm on week days and 9 am to 5 pm at
weekends. Avoid using the hedge trimmer late at night and/or early in the morning.
Safety when using the Hedgetrimmer
When using the hedgetrimmer, grip the handles firmly with both hands, place your feet slightly
apart so your weight is distributed evenly across both legs, and always maintain a steady even
posture while working. Do not use on ladders or if the ground surface is slippery or uneven. Never
attempt to cut directly overhead or with one hand.
• Maintain full engine speed when cutting.
• Never allow other persons to come within the work area as doing so might expose
them to danger.
• Keep work area clear of all persons, particularly small children and pets. Injury may
result from flying debris.
• If a branch or other object gets caught in the hedgetrimmer during operation, always
stop the engine before removing the object.
• To protect yourself against injury from falling branches, wear the required safety
equipment.
• Never touch the spark plug or plug HT cable while the engine
is in operation, doing so may result in an electrical shock.
• Never touch the exhaust, spark plug, or any metallic parts
while the engine is in operation or immediately after shutting
down the engine. These parts reach high temperatures during
operation and doing so could result in serious burns.
• When you finish cutting in one location and wish to continue work in another area, stop
the engine, place the protective cover over the blades, and turn the hedge trimmer so
that the blade faces behind your body before carrying it to the new location.
• Always remove fuel from the fuel tank before transportation to prevent fuel spillage.
• Never leave the hedgetrimmer exposed to direct sunlight as this can heat the fuel tank
and may cause a discharge of fuel, and flood the engine.
Page 10
650DX / 750DX Premium+ Hedgetrimmer
10
Original Instructions Version June 16
650DX+/750DX+_080616
Two-Stroke Fuel
Fuel is very flammable. Do not smoke or bring any flame or sparks near fuel. Always stop the
engine and allow it cool before refuelling. Refuel outdoors on bare ground, restart the engine at
least 5m away from the refuelling stop.
The engine is lubricated by oil mixed into petrol. Prepare a mixture of unleaded petrol and semi-
synthetic two-stroke oil that meets the specifications of: API TC, ISO-L-EGC, JASO FC (Low Smoke)
oil.
Recommended mixing ratio is 40:1.
FUEL WITH NO OIL (RAW PETROL) will cause severe damage to the engine which is not
covered by the manufacturer’s warranty.
Use fresh, unleaded petrol (95 RON) and semi-synthetic oil specially made for high performance
two-stroke engines. Mix in a ratio of 40 parts petrol to 1 part of oil.
By using two-stroke oil specially made for two-stroke engines you will reduce the formation of ash
and carbon deposits on the spark plug, piston, exhaust muer and cylinder as well as reducing
emissions of harmful exhaust gases.
Oil FOR 4-CYCLE ENGINES should not be used as two stroke lubrication oil as it can cause fouling of
the spark plug, exhaust port blocking, piston ring sticking and other internal engine damage.
Page 11
650DX / 750DX Premium+ Hedgetrimmer
11
Original Instructions Version June 16
650DX+/750DX+_080616
Fuel Storage
Mixed two-stroke fuel which has been left unused for a period of one month or more may
damage the carburettor and result in the engine failing to start or operate correctly.
When storing the hedge trimmer for a period of more than one month, empty the fuel tank, and
run the engine to empty the carburettor of fuel.
Two stroke fuel can cause deterioration of rubber and/or plastic components during prolonged
storage.
It is important to only use good quality, fresh fuel mix.
Fuelling
Shake the fuel container to thoroughly mix the two-stroke oil and petrol.
Clean dirt from around the fuel cap before removing.
Pour two-stroke fuel into the fuel tank with a filtered funnel, up to 80% of the fuel tank’s capacity.
Replace the fuel cap and tighten securely. Spilled fuel must be wiped away from the hedge
trimmer before starting the engine.
Move at least 5m away from the refuelling area before restarting the engine.
When refilling the tank, always turn o the engine and allow it to cool down. Take a careful look
around to make sure that there are no sparks or open flames anywhere nearby before refuelling.
Page 12
650DX / 750DX Premium+ Hedgetrimmer
12
Original Instructions Version June 16
650DX+/750DX+_080616
Operation
Keep clear of the blades as they may start moving when
engine starts.
Starting the Engine
CAUTION do not pull the starter cord all the way out and do not let go of the starter handle when
the cord is extended, this can damage the starter mechanism.
Cold Engine Starting
Rest the unit on a flat, firm surface. Keep the blades o the ground and clear of surrounding
objects as they may start moving upon starting the engine.
Fig 1 - Push the air purge bulb (a) until fuel
is visible in the clear return fuel line (b).
Fig 1 Fig 2
(a)
(c)
(b)
Fig 2 - Move the choke lever
to the on position (c).
Page 13
650DX / 750DX Premium+ Hedgetrimmer
13
Original Instructions Version June 16
650DX+/750DX+_080616
Fig 3 - While holding the unit firmly, pull out the
starter rope firmly until engine fires
(indicated by a cough from the engine).
After the engine has started, briefly apply the throttle to set the engine to idle. Allow the engine to
warm up before use. When cutting, always use the hedgetrimmer on full throttle.
Hot Engine Starting
Fig 3 - Pull the starter rope until the engine starts.
If the engine does not start after 5 pulls, use the cold start procedure.
Overchoking
Should the engine become flooded due to overchoking, turn the ignition switch o, unscrew
the spark plug, wipe it dry or replace, pull the recoil starter several times without the spark plug
in place and with choke in the oo position. This will help clean and ventilate the combustion
chamber.
NOTE
Fig 4 - Move the choke lever to the o
position (d).
Pull the starter rope until the engine starts.
Fig 3 Fig 4
(d)
Page 14
650DX / 750DX Premium+ Hedgetrimmer
14
Original Instructions Version June 16
650DX+/750DX+_080616
Stopping the Engine
Set the engine to idling by releasing the throttle lever.
Set the ignition switch to the o position ‘’O’’ (STOP).
After the engine has stopped, wait at least 30 seconds
before attempting to restart.
If the engine fails to stop, set the choke lever to the on
position to stall the engine; do not use the machine until
the ignition switch is repaired.
Running In
During the first ten hours of work, avoid running the engine at maximum speed for a prolonged
period until all the components have bedded in, after the engine has been run in, it will reach its
maximum power.
IMPORTANT
After every use, check that all nuts bolts and screws are securely fastened and tighten if necessary.
Rear Handle
To reduce fatigue when trimming hedges, the handle can be swivelled 90° to the left or right.
Do not use the throttle during this operation!
Proceed as follows:
Free the rear handle by pressing the
locking lever (a).
Turn the rear handle (b) until the locking
lever clicks into place.
When the handle is locked in its new
position you can apply the throttle (c).
NOTE
(a)
(b)
(c)
Page 15
650DX / 750DX Premium+ Hedgetrimmer
15
Original Instructions Version June 16
650DX+/750DX+_080616
Transportation
Never transport the hedgetrimmer with the engine running. An engine that is running
could be accidently accelerated causing the blade to engage.
Make sure the blade safety guards are in place when transporting the hedge trimmer.
When carrying by hand, the cutting head should be pointing backwards.
Ensure the Hedgetrimmer is secure when transporting in a vehicle and the tank is drained of fuel.
Hedge Trimming Techniques
Trim the sides of a hedge first, and then the top.
VERTICAL CUT:
Use an arcing cut from the bottom upwards, then downwards to use both sides of the blades.
Page 16
650DX / 750DX Premium+ Hedgetrimmer
16
Original Instructions Version June 16
650DX+/750DX+_080616
HORIZONTAL CUT:
In order to get the best cutting results, slightly tilt the blade 5 to 10° towards the cutting direction.
Cut slowly, especially when cutting thick hedges.
The hedgetrimmer must only be used to trim hedges or small bushes. It is not to cut
other types of material. Do not use the hedgetrimmer as a lever to lift, move or break
objects. Avoid cutting thick branches, which will damage the blades and shorten the life of the
drive system. Always keep your body to the carburettor side of your hedgetrimmer, never on the
muer side.
Maintenance
IMPORTANT
After every use, check that all nuts, bolts and screws are securely fastened and tighten if
necessary.
In the event of an accident, breakdown or blockage, ensure the engine is turned o before any
work is carried out to rectify this.
Make sure the engine has stopped and is cool before performing any service to the machine.
Contact with a moving cutting head or hot muer may result in a personal injury.
Page 17
650DX / 750DX Premium+ Hedgetrimmer
17
Original Instructions Version June 16
650DX+/750DX+_080616
Always wear heavy-duty gloves when handling the blades.
Blades
Check blades for damage before using the hedgetrimmer.
Clean any residue from the blades using a cleaning agent.
Lubricate the blades with spray oil before and after use.
Sharpening
Always keep the file at an angle of 45° to the blade, and always file in the direction of the cutting
edge.
Note: Files cut only in one direction; lift the file from the blade when returning to start a new pass.
Remove as little material as possible.
Do not try to sharpen a damaged blade; change it or take it to a service dealer.
Page 18
650DX / 750DX Premium+ Hedgetrimmer
18
Original Instructions Version June 16
650DX+/750DX+_080616
Safety Lock
The safety lock is to prevent the throttle lever
from accidentally being engaged.
The throttle lever (a) can only be operated,
if the safety lock (b) is held down.
Check if the safety lock and throttle levers return
to their original position and the engine returns to
idling when you release your hand from the handle.
Gearbox
Every 15 hours of operation apply 3 pumps of grease
using a grease gun and a lithium multi purpose grease,
do not force grease into the gearbox (c) as too much
pressure will damage the seals.
Fuel Filter
Every 15 hours of operation using a wire hook, take the
fuel filter from the fuel tank and clean or replace
with a new fuel filter.
Spark Plug
Poor starting or misfiring is often caused by a fouled or
defective spark plug, clean and reset the gap to 0.65 mm,
or replace the spark plug with NGK: BPMR7A as necessary.
(a)
(b)
(c)
Page 19
650DX / 750DX Premium+ Hedgetrimmer
19
Original Instructions Version June 16
650DX+/750DX+_080616
Air Filter
Before using the hedgetrimmer, check the foam air
filter (a) and pre-filter (b). Being clogged, will reduce
the engine performance.
Clean the filter element in warm, soapy water, dry
completely before installing. If the element is broken
or shrunk, replace with a new one.
Carburettor
The carburettor mixture setting has been set at the
factory and will not need adjusting.
Adjusting the idle speed, if adjustment is
necessary turn the T screw (c) clockwise until the blades
start to move, then turn the screw T anticlockwise
until the blades stop.
If the idle speed cannot be adjusted to stop the
blades moving at idle, contact your dealer for
repair before use.
Storage
Oil the blades to prevent rust.
Remove the spark plug, pour a small amount of 2-stroke oil into the cylinder. Rotate the
crankshaft several times using the starting rope in order to distribute the oil. Put the spark plug
back in.
Remove the fuel from the machine.
(a)
(b)
(c)
(c)
Page 20
650DX / 750DX Premium+ Hedgetrimmer
20
Original Instructions Version June 16
650DX+/750DX+_080616
Troubleshooting
Engine will not start, power loss:
• Check that the fuel tank is not empty. Fill with mixed fuel.
• The fuel does not reach the carburettor. Change the fuel filter in the fuel tank.
• There is water in the fuel. Drain and clean the fuel system.
• The air filter is dirty. Clean or replace the air filter.
• There are carbon deposits in the exhaust muer restricting the engine. Clean or change
the muer.
• Spark plug is worn. Replace spark plug.
Page 21
650DX / 750DX Premium+ Hedgetrimmer
21
Original Instructions Version June 16
650DX+/750DX+_080616
Component Procedure
Before
Use
Every
25
Hours
Every
50
Hours
Every
100
Hours
Note
Fuel Leaks / Fuel
Spillage
Clean Up
•
Fuel Tank / Fuel
Filter
Inspect / Clean
•
Replace if
Neccessary
Idle Adjusting
Screw
See Adjusting
Carburettor
•
Adjust if
Neccessary
Spark Plug Clean and
Readjust Plug
Gap
•
Gap 0.025in (0.6-
0.7mm) Replace if
Neccessary
Cylinder Fins /
Intake Air Cooling
Vent
Clean
•
Muer / Spart
Arrester / Cylinder
Exhaust Port
Clean
•
Throttle Lever /
Ignition Switch
Check Operation
•
Air Filter Clean •
Screws / Nuts /
Bolts
Tighten/Replace Except Adjusting
Screws
Vibration
Elements
Check for
Damage
• •
Replace as
Necessary
Blades Clean and Oil
•
Check for Damage
& Replace as
Necessary
Service Schedule
Page 22
650DX / 750DX Premium+ Hedgetrimmer
22
Original Instructions Version June 16
650DX+/750DX+_080616
Specifications
Model .................................................................................................................. 650DX+ / 750DX+
Type ....................................................................................... Double / Single Sided Hedgetrimmer
Blade length (from the tip of Gear Case)
650DX+ ............................................................................................................................ 600 mm
750DX+ ............................................................................................................................. 750 mm
Eective cutting length
650DX+ ............................................................................................................................. 550 mm
750DX+ ........................................................................................................................... 690 mm
Engine
Model ................................................................................................................................. 1E33F
Displacement .................................................................................................................. 22.2 cm3
Carburettor ............................................................................................................ Diaphragm type
Ignition system ........................................................................ I.C.controlled flywheel magneto
Spark plug ............................................................................................ CDK CMR6A / NGK CMR6A
Fuel ................................... mixture (Gasoline 40 : Oil 1) (using JASO FC or ISO EGC grade oil)
Fuel tank capacity .............................................................................................................. 0.44 L
Starter ..................................................................................................................... Recoil starter
Clutch ................................................................................................................ Centrifugal type
Reduction ratio.......................................................................................................................5:11
Dry weight
650DX+ .......................................................................................................................... 5.2 Kg
750DX+ ......................................................................................................................... 5.4 Kg
Sound pressure level at operation position (EN ISO 10517:2009+A1) LpA: …...... 94.2dB(A)
Uncertainty of stated value (2006/42EC) KpA: …………………………….............. 3.0 dB(A)
Sound power level (EN ISO 10517:2009+A1) LWAd: ………………………... 107.0dB(A)
Total equivalent vibration value:
Front handle ……………………………….........................................................…... 2.12m/s2
Rear handle …………………….........................…………................................... 2.91m/s2
Uncertainty of stated value (2006/42EC): …………….......................………...1.5 m/s
Specifications are subject to change without notice.
Page 23
650DX / 750DX Premium+ Hedgetrimmer
23
Original Instructions Version June 16
650DX+/750DX+_080616
EC Declaration of Conformity
We Mitox (Rochford Garden Machinery Ltd) - BA9 9RS (importer) declare that the
product(s):
Designation: Petrol Powered Hedgetrimmer
Model(s):
650DX Premium + / 750DX Premium +
Type/Serial No: s per rating label on machine
Complies with the following directive(s):
2006/42/EC Machinery Directive
2004/108/EC EMC Directive
97/68/EC Directive as last amended by 2012/26/EU NRMM
2000/14/EC and 2005/88/EC Noise Directive for outdoor equipment use
The conformity assessment procedure followed was in accordance with:
EN ISO 10517:2009 + 1:2013
EN ISO 14982:2009
Notified Body:
Intertek Testing Services
Address:
Building No. 86, 1198 Qinzhou Road (North) Shanghai 200233, China
Measured Sound Power Level:
104.3 dB ()
Guaranteed Sound Power Level: 107 dB ()
Authorised Signatory and Technical File Holder
Date: 06/06/2016
Signature:
Name: Stewart nderson
Position: Managing Director
Company: Mitox (Rochford Garden Machinery Ltd)
Address:
Wincanton Business Park
Wincanton
Somerset
B9 9RS
Page 24
650DX / 750DX Premium+ Hedgetrimmer
24
Original Instructions Version June 16
650DX+/750DX+_080616
650DX+ BSE UNIT
Page 25
650DX / 750DX Premium+ Hedgetrimmer
25
Original Instructions Version June 16
650DX+/750DX+_080616
ITEM PRT NUMBER DESCRIPTION QTY
2 MIGB/T845 ST4.8X25 TPPING SCREW ST4.8X25 2
3 MIGJB25D.00.00-13 WSHER 5X12X1.5 12
4 MIHT2360D.00.00-1 FRONT HNDLE 1
5 MIHT2360D.01.09.03-00 COVER 1
6 MIHT2360D.04.00-2 GER BOX COVER 1
7 MIGB/T97.1 M5 WSHER M5 8
8 MIGB/T93 M5 SPRING WSHER M5 12
9 MIGB/T6191 M5X18 SCREW M5X18 8
10 MIHT2360D.00.00-2 BLDE DRIVE CSE (BSE) 1
11 MIGB/T845 ST4.2X14 TPPING SCREW ST4.2X14 6
12 MIHT2360D.05.00-2 RER HNDLE LEFT COVER 1
13 MIHT2360D.00.00-7 O-RING SEL (43.8X3.1) 1
14 MIHT2360D.05.00-9 RETURN SPRING 1
15 MIHT2360D.05.00-8 ROTTION CONTROL LEVER 1
16 MIHT2360D.05.00-3 THROTTLE TRIGGER 1
17 MIHT2360D.05.00-6 THROTTLE TRIGGER LOCKOUT 1
18 MIHT2360D.05.00-1 RER HNDLE RIGHT COVER 1
19 MIHT2360D.05.01-00 GRIP SKIN 1
20 MIHT2360D.00.04-00 ENGINE SWITCH 1
21 MI23151-B001-0000 WTER RESISTNT CP 1
22 MIHT2360D.00.03-00 GROUND CONNECTING WIRE 1
23 MIHT2360D.00.02-00 SWITCH CONNECTING WIRE 1
24 MIHT2360D.05.00-7 THROTTLE RETURN SPRING 1
25 MIHT2360D.05.00-5 RETURN SPRING 1
26 MIHT2360D.05.00-4 POSITION BLOCK 1
27 MIHT2360D.00.00-9 RER THROTTLE CBLE TUBE 1
28 MIHT2360D.00.00-3 COVER 1
29 MIHT2360D.00.00-8 FRONT THROTTLE CBLE TUBE 1
30 MIHT2360D.00.01-00 THROTTLE CBLE 1
31 MIGB/T6191 M5X14 SCREW M5X14 2
32 MIHT2360D.00.00-6 WSHER 2
33 MIHT2360D.00.00-5 RER BSORBER SPRING 2
34 MIGB/T845 ST4.8X19
TPPING SCREW ST4.8X19 6
35 MIHT2360D.00.00-4 FRONT BSORBER SPRING 2
36 MIGJB25D.04.00-11 CON ROD 2
37 MIGB/T276 61805-2Z BERING 61805-2Z 25X37X7 2
38 MIGJB25D.04.00-7 ECCENTRIC GER 1
39 MIGJB25D.04.00-9 GER CSE GSKET 1
40 MIGB/T276 608-2RS BERING 608-2RS 8X22X7 1
Page 26
650DX / 750DX Premium+ Hedgetrimmer
26
Original Instructions Version June 16
650DX+/750DX+_080616
ITEM PRT NUMBER DESCRIPTION QTY
41 MIHT2360D.04.00-5 OUTPUT SHFT 1
42 MIGB/T276 6001-2RS BERING 6001-2RS 12X28X8 1
43 MIGB/T6191 M6X22 SCREW M6X22 3
44 MIGB/T93 M6 LOCK WSHER M6 3
45 MIGB/T97.1 M6 FLT WSHER M6 4
46 MIHT2360D.04.00-1 BLDE DRIVE CSE (TOP) 1
47 MIGJB25D.04.01-00 GRESE NIPPLE 1
48 MIHT2360D.04.01-00 CLUTCH DRUM 1
49 MIGB/T6191 M5X12 SCREW M5X12 2
50 MIHT2360D.00.05-00 EXHUST PIPE 1
51 MIGB/T6187.1 M5 NUT M5 11
52 MIGJB25D.04.00-6 LINK ROD PLTE 2
53 MIGB/T2672 M4X10 SCREW M4X10 4
54 MIGB/T119.2 3X9 PIN 3X9 2
55 MIGB/T119.2 6X35 PIN 6X35 1
56 MIHT2360D.06.01-00 BLDE 2
57 MIGJB25D.06.00-3 BUSH 10
58 MIHT2360D.06.00-3 BOTTOM GRIPPER PLTE 1
59 MIHT2360D.04.00-4 FELT 1
60 MIHT2360D.06.00-2 PLTE 1
61 MIHT2360D.06.00-1 UPPER GRIPPER PLTE 1
62 MIHT2360D.06.00-7 SCREW M5X44 1
63 MIHT2360D.06.00-10 SQURE NUT M5 7
64 MIHT2360D.06.00-4 BUSH 6X8X3 5
65 MIHT2360D.06.00-6 SCREW M5X40 1
66 MIHT2360D.06.00-11 PLTE 1
67 MIGB/T6186 M5 NUT M5 1
68 MIHT2360D.06.00-5 TIP GURD 1
69 MIHT2360D.06.00-9 SCREW M5X17 1
70 MIHT2360D.06.00-8 SCREW M5X25 7
71 MIHT2375D.00.00-11 BLDE COVER 1
72 MI12.01.0557. HNDLE SSY 1
Page 27
650DX / 750DX Premium+ Hedgetrimmer
27
Original Instructions Version June 16
650DX+/750DX+_080616
750DX+ BSE UNIT
Page 28
650DX / 750DX Premium+ Hedgetrimmer
28
Original Instructions Version June 16
650DX+/750DX+_080616
ITEM PRT NUMBER DESCRIPTION QTY
2 MIGB/T845 ST4.8X25 TPPING SCREW ST4.8X25 2
3 MIGJB25D.00.00-13 WSHER 5X12X1.5 12
4 MIHT2360D.00.00-1 FRONT HNDLE 1
5 MIHT2360D.01.09.03-00 COVER 1
6 MIHT2360D.04.00-2 GER BOX COVER 1
7 MIGB/T97.1 M5 WSHER M5 8
8 MIGB/T93 M5 SPRING WSHER M5 12
9 MIGB/T6191 M5X18 SCREW M5X18 8
10 MIHT2360D.00.00-2 BLDE DRIVE CSE (BSE) 1
11 MIGB/T845 ST4.2X14 TPPING SCREW ST4.2X14 6
12 MIHT2360D.05.00-2 RER HNDLE LEFT COVER 1
13 MIHT2360D.00.00-7 O-RING SEL (43.8X3.1) 1
14 MIHT2360D.05.00-9 RETURN SPRING 1
15 MIHT2360D.05.00-8 ROTTION CONTROL LEVER 1
16 MIHT2360D.05.00-3 THROTTLE TRIGGER 1
17 MIHT2360D.05.00-6 THROTTLE TRIGGER LOCKOUT 1
18 MIHT2360D.05.00-1 RER HNDLE RIGHT COVER 1
19 MIHT2360D.05.01-00 GRIP SKIN 1
20 MIHT2360D.00.04-00 ENGINE SWITCH 1
21 MI23151-B001-0000 WTER RESISTNT CP 1
22 MIHT2360D.00.03-00 GROUND CONNECTING WIRE 1
23 MIHT2360D.00.02-00 SWITCH CONNECTING WIRE 1
24 MIHT2360D.05.00-7 THROTTLE RETURN SPRING 1
25 MIHT2360D.05.00-5 RETURN SPRING 1
26 MIHT2360D.05.00-4 POSITION BLOCK 1
27 MIHT2360D.00.00-9 RER THROTTLE CBLE TUBE 1
28 MIHT2360D.00.00-3 COVER 1
29 MIHT2360D.00.00-8 FRONT THROTTLE CBLE TUBE 1
30 MIHT2360D.00.01-00 THROTTLE CBLE 1
31 MIGB/T6191 M5X14 SCREW M5X14 2
32 MIHT2360D.00.00-6 WSHER 2
33 MIHT2360D.00.00-5 RER BSORBER SPRING 2
34 MIGB/T845 ST4.8X19
TPPING SCREW ST4.8X19 6
35 MIHT2360D.00.00-4 FRONT BSORBER SPRING 2
36 MIGJB25D.04.00-11 CON ROD 2
37 MIGB/T276 61805-2Z BERING 61805-2Z 25X37X7 2
38 MIGJB25D.04.00-7 ECCENTRIC GER 1
39 MIGJB25D.04.00-9 GER CSE GSKET 1
40 MIGB/T276 608-2RS BERING 608-2RS 8X22X7 1
Page 29
650DX / 750DX Premium+ Hedgetrimmer
29
Original Instructions Version June 16
650DX+/750DX+_080616
ITEM PRT NUMBER DESCRIPTION QTY
41 MIHT2360D.04.00-5 OUTPUT SHFT 1
42 MIGB/T276 6001-2RS BERING 6001-2RS 12X28X8 1
43 MIGB/T6191 M6X22 SCREW M6X22 3
44 MIGB/T93 M6 LOCK WSHER M6 3
45 MIGB/T97.1 M6 FLT WSHER M6 4
46 MIHT2360D.04.00-1 BLDE DRIVE CSE (TOP) 1
47 MIGJB25D.04.01-00 GRESE NIPPLE 1
48 MIHT2360D.04.01-00 CLUTCH DRUM 1
49 MIGB/T6191 M5X12 SCREW M5X12 2
50 MIHT2360D.00.05-00 EXHUST PIPE 1
51 MIGB/T6187.1 M5 NUT M5 11
52 MIGJB25D.04.00-6 LINK ROD PLTE 2
53 MIGB/T2672 M4X10 SCREW M4X10 4
54 MIGB/T119.2 3X9 PIN 3X9 2
55 MIGB/T119.2 6X35 PIN 6X35 1
56 MIHT2375D.06.01-00 BLDE 2
57 MIGJB25D.06.00-3 BUSH 10
58 MIHT2375D.06.00-3 BOTTOM GRIPPER PLTE 1
59 MIHT2360D.04.00-4 FELT 1
60 MIHT2375D.06.00-2 PLTE 1
61 MIHT2375D.06.00-1 UPPER GRIPPER PLTE 1
62 MIHT2360D.06.00-7 SCREW M5X44 1
63 MIHT2360D.06.00-10 SQURE NUT M5 7
64 MIHT2360D.06.00-4 BUSH 6X8X3 5
65 MIHT2360D.06.00-6 SCREW M5X40 1
66 MIHT2360D.06.00-11 PLTE 1
67 MIGB/T6186 M5 NUT M5 1
68 MIHT2360D.06.00-5 TIP GURD 1
69 MIHT2360D.06.00-9 SCREW M5X17 1
70 MIHT2360D.06.00-8 SCREW M5X25 7
71 MIHT2375D.00.00-1 BLDE COVER 1
72 MI12.01.0557. HNDLE SSY 1
Page 30
650DX / 750DX Premium+ Hedgetrimmer
30
Original Instructions Version June 16
650DX+/750DX+_080616
650DX+ / 750DX+ ENGINE
Page 31
650DX / 750DX Premium+ Hedgetrimmer
31
Original Instructions Version June 16
650DX+/750DX+_080616
ITEM PRT NUMBER DESCRIPTION QTY
1 MIHT2360D.01.08.02-00 HND SCREW 1
2 MIHT2360D.01.08.00-1 IR FILTER COVER 1
3 MIHT2360D.01.08.00-3 IR FILTER 1
4 MIHT2360D.01.08.00-2 SPONGE FILTER 1
5 MIGB/T9074.4 M5X65 SCREW M5×65 2
6 MIHT2360D.01.08.00-4 BLOCK 1
7 MIHT2360D.01.00.00-15 BUSH 5X6.5X9 2
8 MIHT2360D.01.00.00-10 LOCK PLTE 1
9 MIHT2360D.01.08.03-00 IR FILTER CASE 1
10 MIHT2360D.01.00.00-9 GSKET (IR FILTER) 2
11 MIHT2360D.01.00.00-4 CBLE SUPPORT FRME 1
12 MIHT2360D.01.06.00-00 CRBURETTOR 1
13 MIGJB25D.01.00.00-6 GSKET 1
14 MIHT2360D.01.00.00-16 SPCER PLTE 1
15 MIHT2360D.01.00.00-6 GSKET 1
16 MIGB/T6191 M5X18 SCREW M5X18 5
17 MIGB/T93 M5 SPRING WSHER M5 13
18 MIGB/T97.1 M5 WSHER M5 7
19 MIHT2360D.01.00.00-14 BUSH 5X6.3X7 3
20 MIHT2360D.01.00.01-00 INTKE PIPE 1
21 MIHT2360D.01.00.00-5 GSKET (INTKE) 1
22 MIYD25.01.00.00-2 IGNITION GSKET 2
23 MIGB/T97.1 M4 PLIN WSHER M4 2
24 MIGB/T93 M4 WSHER M4 2
25 MIGB/T6191 M4X20 SCREW M4X20 2
26 MIHT2360D.01.11.03-00 GROUND WIRE 1
27 MIHT2360D.01.11.01-00 IGNITION COIL 1
28 SPCMR6A SPRK PLUG 1
29 MIHT2360D.01.00.00-13 BUSH 1
30 MIGJB25D.00.00-13 WSHER 5X12X1.5 1
31 MIHT2360D.01.00.00-2 CYLINDER COVER 1
32 MIHT2360D.06.00-10 SQURE NUT M5 1
33 MIHT2360D.01.00.00-3
MUFFLER COVER 1
34 MIGB/T6191 M5X14 SCREW M5X14 4
35 MIGB/T6191 M5X50 SCREW M5X50 2
36 MIGJB25D.01.00.00-17 COPPER WSHER M5 2
37 MIHT2360D.01.09.03-00 COVER 1
38 MIGB/T818 M5X5 SCREW M5X5 1
39 MIGB/T818 M4X5 SCREW M4X5 3
Page 32
650DX / 750DX Premium+ Hedgetrimmer
32
Original Instructions Version June 16
650DX+/750DX+_080616
ITEM PRT NUMBER DESCRIPTION QTY
40 MIHT2360D.01.09.02-00 EXHUST PIPE 1
41 MIHT2360D.01.09.00-1 GSKET (EXHUST) 1
42 MIHT2360D.01.09.01-00 EXHUST 1
43 MIHT2360D.01.00.00-7 GSKET (EXHUST) 1
44 MIGB/T6191 M5X20 SCREW M5X20 4
45 MIHT2360D.01.02.00-00 CYLINDER COVER 1
46 MIHT2360D.01.00.00-8 GSKET (CYLINDER) 1
47 MIHT2360D.01.03.00-1 PISTON RING 2
48 MIHT2360D.01.03.02-00 PISTON 1
49 MIYD36.01.03.00-4 PISTON PIN CIRCLIPS 2
50 MIHT2360D.01.03.01-00 CRNKSHFT 1
51 MIGB/T276 6000/P6 BERING 6000/P6 2
52 MIGB/T119.2 5X10 PIN 5X10 2
53 MIHT2360D.01.01.00-3 GSKET (CRNKCSE) 1
54 MIHT2360D.01.01.00-2 BOTTOM CRNKCSE 1
55 MIGJB25D.01.00.06-00 OIL SELS 10X20X5 2
56 MIYD25.01.13.00-2 CLUTCH WSHER 1
59 MIYD25.01.13.01-3 CLUTCH SPRING 2
60 MIYD25.01.13.01-00 CLUTCH 1
61 MIYD38-3.03.00-4 PRIMER SSY 1
62 MIHT2360D.01.00.00-12 PRIMER TUBE 2.5X5X75 1
63 MIHT2360D.01.13.00-3 RETURN TUBE 2.5X5X100 1
64 MIGJB25D.03.00-1 GROMMET 1
65 MIHT2360D.01.13.00-2 FUEL TUBE 2.5X5X230 1
66 MIYD45.01.01.01-3 CIRCLIP 1
67 MIYD38-3.03.04-00 FUEL FILTER 1
68 MIGB/T96 M5 WSHER M5 1
69 MIHT2360D.01.13.00-1 FUEL TNK 1
70 MIHT2360D.01.00.00-11 FUEL TNK BSORBER 2
71 MIHT2360D.01.13.01-00 FUEL CP 1
72 MIGJB25D.03.01-6 CP RETINER 1
79 MIHT2360D.01.00.00-1 TOP COVER 1
80 MIGB/T2672 M4X12
SCREW M4×12 1
81 MIGB/T96 M4 WSHER M4 1
82 MITHT245D.02.00-6 RTCHET GER 1
83 MITHT245D.02.00-7 TORQUE SPRING 1
84 MITHT245D.02.00-1 RECOIL PULLEY 1
85 MITBC261D.01.12.00-5 RECOIL SPRING 1
86 MIHT2360D.01.12.01-00 STRTER COVER 1
Page 33
650DX / 750DX Premium+ Hedgetrimmer
33
Original Instructions Version June 16
650DX+/750DX+_080616
ITEM PRT NUMBER DESCRIPTION QTY
87 MIGB/T845 ST4X14 TPPING SCREW ST4.2X14 1
88 MITCS6200.02.00-3 STRTER HNDLE 1
89 MIGJB25D.02.00-3 ROPE 1
90 MIHT2360D.01.12.00-00 STRTER 1
91 MIGB/T6187.1 M6 HEXGON NUT WITH FLNGE M6 1
92 MIHT2360D.01.10.00-00 FLYWHEEL 1
93 MIGB/T6191 M5X25 SCREW M5X25 1
94 MIHT2360D.01.01.00-1 TOP CRNKCSE 1
95 MIGB/T1099 3X3.5X10 SEMI-CIRCULR KEY 3X3.5X10 1
96 MIHT2360D.01.03.03-00 BERING 8X11X10 1
97 MIHT2360D.01.03.00-2 PISTON PIN 1
Page 34
650DX / 750DX Premium+ Hedgetrimmer
34
Original Instructions Version June 16
650DX+/750DX+_080616
Page 35
650DX / 750DX Premium+ Hedgetrimmer
35
Original Instructions Version June 16
650DX+/750DX+_080616
Page 36
650DX / 750DX Premium+ Hedgetrimmer
36
Original Instructions Version June 16
650DX+/750DX+_080616
CONDITIONS OF WARRANTY
The manufacturer warrants the product against faulty materials and workmanship for a standard
1 year period and thereafter for the set period specific to each range from the date of purchase.
Warranty does not extend to failure due to fair wear and tear.
SP - 1 Year
SELECT - 3 Years (Subject to yearly servicing)
PREMIUM - 5 Years (Subject to yearly servicing)
PRO - 5 Years Domestic / 3 Years Commercial (Subject to yearly servicing)
(Extended warranty is subject to online registration and yearly servicing)
SP, SELECT and PREMIUM ranges used for commercial purposes have a warranty period of 3
months from the date of purchase.
The manufacturer undertakes to replace any spare parts that are classified as defective by an
appointed Mitox service dealer. The manufacturer will not accept liability for the replacement of
the machine, either partially or wholly, and /or consequential damages and /or interest charges
either directly or indirectly.
Warranty does not cover failure due to:
Insucient maintenance.
Incorrect fuel mixture and stale fuel.
bnormal use or accidental damage.
Incorrect assembly, adjustment or operation of the product.
Spare parts that are subject to wear e.g. bag, blades, bearings, cables, guards, deflectors,
spark plugs, air filters etc.
Neither does warranty extend to:
Freight and packing costs.
Use of non-genuine spare parts i.e. those from another manufacturer.
Use of the machine for any other purpose than that for which it was designed.
Use and maintenance of the machine in a manner not described in the owner’s manual.
s part of our policy of continuous product improvement, we reserve the right to alter or
amend this specification without notice. s a result, the product may dier from the information
contained herein but any alteration will only be implemented without notice if it is classified as an
improvement to the above specification.
READ THE MANUAL CAREFULLY BEFORE OPERATING THE MACHINE
When ordering spare parts, please quote the part number, this can be found in the parts list
included in this manual.
Retain your proof of purchase, without which no warranty can be oered.
Mitox Garden Machinery, Wincanton Business Park, Wincanton, Somerset, B9 9RS
Loading...