Operator’s Manual
user manual, maintenance instructions and spare parts
26L/U, 33L/U,43U, 53U Brushcutter
www.mitox.co.uk
Read this manual carefully before operating the machine
Original Instructions Version June 16
26LU-33LU-43U-53U_210616
26L/U, 33L/U, 43U, 53U
2
Original Instructions Version June 16
PRODUCT DESCRIPTION
This Brushcutter is a 2 stroke fast running power tool and is designed to be used in a domestic
application for trimming grass and light brush.
8
10
9
11
13
1
2
3
3
19
4
5
5
6
7
8
8
10
10
12
12
14
15
16
16
17
18
18
4
20
20
26L/U, 33L/U, 43U, 53U
3
Original Instructions Version June 16
Warnings in the Manual
This mark indicates instructions which must be followed in order to prevent accidents which could
lead to serious bodily injury or death.
This mark indicates instructions which must be followed or it leads to mechanical failure,
breakdown, or damage.
This mark indicates hints or useful directions in the use of the product.
IMPORTANT
!
NOTE
Component Location
1 BLADE 3 Point blade for grass, weed or brush cutting applications.
2 DRIVE SHAFT Contains the drive shaft.
3 THROTTLE TRIGGER Spring loaded to return to idle when released.
4 IGNITION SWITCH Slide switch, forward to run, back to stop.
5 SAFETY LEVER Prevents accidental operation of the throttle.
6 HANDLE This handle can be adjusted for maximum comfort
7 HARNESS ASSEMBLY Fully adjustable for maximum comfort
8 PETROL CAP
9 PURGE BULB Push the purge bulb to remove the air from the fuel system.
10 FUEL TANK Contains fuel and fuel filter
11 AIR CLEANER Contains replaceable filter
12 CHOKE To help in cold starting
13 STARTER HANDLE Pull to start the engine
14 DEBRIS SHIELD Helps protect the operator from debris
15 CUT-OFF KNIFE Cuts the nylon line to the correct length
16 NYLON CUTTER HEAD Contains replaceable nylon trimming line
17 FRONT HANDLE This handle can be adjusted for maximum comfort
18 GEARBOX For attaching a blade or nylon head to
19 REAR HANDLE Incorporating throttle trigger, switch, and safety lever
20 HARNESS FIXING POINT Fixing point to attach the harness
26L/U, 33L/U, 43U, 53U
4
Original Instructions Version June 16
Safety Symbols
Warning: Danger, Caution
Read the documentation and safety instructions which are
provided in this user manual.
When operating this machine, use protective equipment such
as goggles, helmet and ear defenders.
Wear security shoes and gloves.
Check the condition of working area to avoid any accident
by hitting hidden obstacles such as stumps, stones, cans, or
broken glass.
Hot surface: Risk of burn.
Danger: Risk of intoxication.
Danger: Risk of fire or explosion
Directive 2000-14/CE. Guaranteed noise levels
Beware of objects being thrown from the operating zone
Warning: Keep all people, animals and vulnerable objects at
least 15 metres from the working area.
26L/U, 33L/U, 43U, 53U
5
Original Instructions Version June 16
Taking Care of Warning Labels
Always keep warning labels clean and free of scratches, which might make them illegible or
dicult to read. If the warning labels provided with your Brushcutter become damaged, peel
o, or otherwise become illegible or dicult to read, order new labels from the authorised
servicing dealer and replace the damaged labels. When applying new labels, first wipe away any
dirt and dry the surface before applying the new label in the same place as the original label.
Explanation of Symbols on the Machine
For safe operation and maintenance, symbols are carved in relief on the machine:
FUEL TANK
Fuel tank 2 stroke mix
Position: Fuel cap
CHOKE OPERATION
<RUN>
Starting mode when the engine is hot (choke o).
Position: Air cleaner cover.
<START>
Starting mode when the engine is cold (choke on).
Position: Air cleaner cover.
Never modify the cutter in any way. Improper use of any
cutter can cause serious or fatal injury.
Beware of blade thrust
26L/U, 33L/U, 43U, 53U
6
Original Instructions Version June 16
Safety Precautions
Introduction
Read this Owner/Operator Manual carefully. Be sure you understand how to operate this
Brushcutter properly before you use it. Failure to do so could result in serious injury.
Keep this manual handy so that you may refer to it later whenever any questions arise. Also note
that you are able to contact the dealer from whom you purchased the product for assistance.
Always include this manual when selling, lending, or otherwise transferring the ownership of this
product.
This product has been designed to be used as a Brushcutter power tool as described previously
and it should never be used for any other purpose; doing so could result in unforeseen accidents
and injuries occurring. Only approved Mitox accessories should be used with this product.
This Brushcutter is equipped with extremely sharp blades, always wear sturdy gloves when
handling the blades and fit the safety guards when not in use.
When using this Brushcutter for the first time, take the Brushcutter to a wide, clear, open space,
start the engine, and practice handling the Brushcutter until you are sure that you will be able to
handle it properly in actual operation.
You should never use this Brushcutter when under the influence of alcohol, suering from
exhaustion or lack of sleep, suering from drowsiness as a result of having taken medicine, or at
any other time when your judgement might be impaired or that you might not be able to operate
the Brushcutter properly and in a safe manner.
Never allow children or anyone unable to fully understand the directions given in this manual to
use this Brushcutter
When planning your work schedule, allow plenty of time to perform the work and allow plenty of
time for rest. Limit the amount of time you continuously use the Brushcutter to 30~40 minutes
per session and take 10~20 minutes of rest between work sessions. Also, try to keep the total
amount of work performed in a single day to 2 hours.
Never run the engine indoors as the exhaust gases contain harmful carbon monoxide.
26L/U, 33L/U, 43U, 53U
7
Original Instructions Version June 16
Never use the Brushcutter in conditions as described
below:
When the ground is slippery or when other conditions exist which might make it dicult to
maintain a steady posture while using the Brushcutter.
At night, at times of heavy fog, or at any other times when your field of vision is limited and it
would be dicult to gain a clear view of the area where the Brushcutter is to be used. In heavy
rain, during lightning storms, at times of strong or gale-force winds, or at any other times when
weather conditions might make it unsafe to use this product.
Lack of sleep, tiredness, or physical exhaustion results in lower attention spans, and this in turn
can lead to accidents and injury.
Work Clothing and Safety Equipment
When using the product, you should wear proper clothing and protective equipment.
• Helmet
• Protection goggles or face protector
• Ear protectors
• Thick work gloves
• Non-slip sole work boots
• When using your Brushcutter, always wear strong, durable, work clothing; shirts
should be long-sleeved and trousers should be full-length.
Safety and Operation
This Brushcutter is equipped with a very sharp blade, and when used incorrectly the blade can be
extremely dangerous.
Improper handling can cause accidents which may in turn lead to serious injury or death. For
26L/U, 33L/U, 43U, 53U
8
Original Instructions Version June 16
this reason, you should always be careful to adhere to the following instructions when using your
Brushcutter.
Never hold the Brushcutter in a way in which the cutting head is pointing towards someone else.
Never allow the blade to come into contact with your body.
Always turn o the engine before adjusting the Brushcutter, or at any time when coming into
close proximity with the cutting head.
Always wear thick work gloves when adjusting the Brushcutter.
Safe Handling of Fuel
The engine of the Brushcutter is designed to run on a two stroke oil/fuel mixture.
This fuel is highly flammable, never store cans of fuel or refill the fuel tank in any place where
there is a source of heat or fire, which might ignite the fuel.
Do not smoke whilst operating the Brushcutter or refilling, keep lit cigarettes away from the
Brushcutter at all times.
When refilling the fuel tank always stop the engine first and carefully make sure that there are no
sparks or naked flames anywhere nearby before refuelling.
If any fuel spillage occurs during refuelling, use a dry rag to wipe any fuel which has been spilled
onto the Brushcutter before starting the engine.
After refuelling, screw the fuel cap back tightly onto the fuel tank and carry the Brushcutter to a
spot 5 metres or more away from where it was refuelled before starting the engine.
26L/U, 33L/U, 43U, 53U
9
Original Instructions Version June 16
Before Operating the Brushcutter
Before beginning work, carefully check the work area and remove any obstacles. Within a
perimeter of 15 metres of the work area should be considered a hazardous area into which no-
one should enter while the Brushcutter is being used, and when necessary this area should be
marked with a warning rope, warning signs, or other forms of warning.
When work is to be performed simultaneously by two or more operators, care should also be
taken to constantly look around to check the presence and locations of other operators within the
work area to maintain a safe distance between each operator.
Before beginning work, each component of the Brushcutter should be checked to make sure
that it is in proper working order, make sure that there are no loose screws or bolts, fuel leaks,
ruptures, dents, broken guards or any other problems which might interfere with safe operation.
Keep all parts of your body away from the cutting head when the engine is running.
Before Starting the Engine
Carefully check the work area to make sure that no obstacles exist within a perimeter of 15
metres around the Brushcutter before starting the engine.
To start the engine, place the Brushcutter onto the ground in a flat clear area and hold it firmly
in place to ensure that neither the cutting head nor the throttle come into contact with any
obstacles when the engine starts.
After starting the engine, make sure that the cutting head stops moving when the throttle trigger
is released (idle). If the cutting head continues to move when the engine is at idle, adjust the
idle screw on the carburettor to a point where the cutting head stops moving, if this cannot be
achieved, take the Brushcutter to your authorised service dealer for adjustment.
26L/U, 33L/U, 43U, 53U
10
Original Instructions Version June 16
Avoid Noise Problems
Check and follow the local regulations for sound levels and hours of operation for garden
machinery.
In general, operate Brushcutters between 8 am and 5 pm on weekdays and 9 am to 5 pm at
weekends.
Avoid using the Brushcutter late at night and/or early in the morning.
Safety when using the Brushcutter
When using the Brushcutter, grip the handles firmly with both hands, place your feet slightly apart
so your weight is distributed evenly across both legs, and always maintain a steady even posture
while working.
• Maintain full engine speed when cutting.
• Never allow other persons to come within the work area as doing so might expose
them to danger.
• Keep work area clear of all persons, particularly small children and pets. Injury may
result from flying debris.
• If grass or other objects get caught in the Brushcutter during operation, always stop
the engine before removing the object.
• Never touch the spark plug or plug HT cable while the engine is in
operation, doing so may result in an electrical shock.
• Never touch the exhaust, spark plug, or any metallic parts while the
engine is in operation or immediately after shutting down the engine.
These parts reach high temperatures during operation and doing so
could result in serious burns.
• When you finish cutting in one location and wish to continue work in another area, stop
the engine.
• Always remove fuel from the fuel tank before transportation to prevent fuel spillage.
• Never leave the Brushcutter exposed to direct sunlight as this can heat the fuel tank
and may cause a discharge of fuel, and flood the engine.
• Be careful not to hit the nylon cutting head against stones or the ground.
26L/U, 33L/U, 43U, 53U
11
Original Instructions Version June 16
Two-Stroke Fuel
Fuel is very flammable. Do not smoke or bring any flame or sparks near fuel.
Always stop the engine and allow it to cool before refuelling.
Refuel outdoors on bare ground, restart engine at least 5m away from the refuelling stop.
The engine is lubricated by oil mixed into petrol. Prepare a mixture of unleaded petrol and semi-
synthetic two-stroke oil that meets the specifications of: API TC, ISO-L-EGC, JASO FC (Low Smoke)
oil.
Recommended mixing ratio is 40:1
FUEL WITH NO OIL (RAW PETROL) will cause severe damage to the engine which is not
covered by manufacturer’s warranty.
Use fresh, unleaded petrol (95 RON) and semi-synthetic oil specially made for high performance
two-stroke engines. Mix in a ratio of 40 parts petrol to 1 part of oil.
By using two-stroke oil specially made for two-stroke engines you will reduce the formation of ash
and carbon deposits on the spark plug, piston, exhaust muer and cylinder as well as reducing
emissions of harmful exhaust gases.
Oil FOR 4-CYCLE ENGINES should not be used as two-stroke lubrication oil as it can cause fouling
of the spark plug, exhaust port blocking, piston ring sticking and other internal engine damage.
NOTE
Due to increased Ethanol content in petrol we
recommend the use of B3C Ethanol Shield
2-Stroke Oil, and Ethanol Shield Fuel Stabiliser
to protect your MITOX® engine against the
harmful eects of Ethanol.
www.b3cfuel.co.uk
26L/U, 33L/U, 43U, 53U
12
Original Instructions Version June 16
Fuel Storage (Without Ethanol Shield)
Mixed two-stroke fuel which has been left unused for a period of one month or more may
damage the carburettor and result in the engine failing to start or operate correctly.
When storing the Hedgetrimmer for a period of more than one month, empty the fuel tank, and
run the engine to empty the carburettor of fuel.
Two stroke fuel can cause deterioration of rubber and/or plastic components during prolonged
storage.
It is important to only use good quality, fresh fuel mix.
Fuelling
Shake the fuel container to thoroughly mix the two-stroke oil and petrol.
Clean dirt from around the fuel cap before removing.
Pour two-stroke fuel into the fuel tank with a filtered funnel, up to 80% of the fuel tank’s capacity.
Replace the fuel cap and tighten securely. Spilled fuel must be wiped away from the
Hedgetrimmer before starting the engine.
Move at least 5m away from the refuelling area before restarting the engine.
When refilling the tank, always turn o the engine and allow it to cool down. Take a careful look
around to make sure that there are no sparks or open flames anywhere nearby before refuelling.
26L/U, 33L/U, 43U, 53U
13
Original Instructions Version June 16
Assembly of the Brushcutter
The blade fitted to the guard is sharp and can cause injury, always wear gloves.
Installing the Guard
• Place the Brushcutter with the head facing down.
• Fit the shield using the bracket and 2 X M5x16 screws
26L/U, 33L/U, 43U, 53U
14
Original Instructions Version June 16
Installing the Nylon Head
• Lay the Brushcutter on its back with the gearbox shaft facing up.
Rotate the gear box shaft until the hole
in the holder A lines up with the slot in
the metal guard.
Insert an Allen key or screwdriver into
the hole in the gearbox cover and into
holder A.
Screw the nylon head anti-clockwise
(turn left) onto the threaded shaft on the
end of the gearbox.
Make sure that the nylon head is
securely locked in position and remove
the Allen key.
A
A
26L/U, 33L/U, 43U, 53U
15
Original Instructions Version June 16
Installing the 3 Tooth Blade
• Lay the Brushcutter on its back with the gearbox shaft facing up.
THE BLADE MUST BE CORRECTLY POSITIONED ON THE UPPER BLADE CLAMP
OTHERWISE SERIOUS DAMAGE AND INJURY TO PERSONS AND PROPERTY COULD
RESULT.
Rotate the
gear box shaft
until the hole
in the holder A
lines up with
the slot in the
metal guard.
Insert an
Allen key or
screwdriver
into the hole
in the gearbox
cover and into
holder A.
Place the 3 tooth
blade on the
holder A, centring
the blade on the
raised centre.
Fit the holder
B over the
blade.
Fit the domed nut
protector C over
holder B and the
blade.
Fit the nut anti-
clockwise (turn
left) and tighten
using the spanner
provided. Remove
the Allen key /
screwdriver.
A
A
A
B
C
26L/U, 33L/U, 43U, 53U
16
Original Instructions Version June 16
Using the Brushcutter
Choosing the cutting device
Choose the most suitable cutting device for the job to be done, according to these general
indications:
• The cutting line head can eliminate tall grass and non-woody vegetation
• The 3-point blade is suitable for cutting brushwood and small shrubs up to 2 cm in
diameter.
Nylon Head
• Cut the grass in 1.5 metre widths, keeping the machine well balanced.
• Avoid engaging stones, piles of earth, small pieces of wood or anything that could be
hidden or dicult to see in the grass. If a large object is accidentally struck, if the cutting
head gets blocked, overloaded or stringy material gets wrapped in the cutting head,
reduce the engine speed so the engine idles. Make sure that the cutting head has
stopped rotating switch o the engine and remove the material.
• Put the Brushcutter on the ground and check that the cutting head has not been
damaged. If necessary, change the cutting head. If the head is only wrapped by
vegetation, remove by hand and clean the cutting head.
• Always wear safety gloves for this operation and ensure the engine is switched o and
the head is stationary.
• When the 2 nylon cords become too short, accelerate the engine and bump the nylon
head on the ground. Automatically the 2 nylon cords will feed out and be cut to the
correct length. Repeat the operation if necessary.
26L/U, 33L/U, 43U, 53U
17
Original Instructions Version June 16
3-Point Blade
• Start cutting above the undergrowth and then move down with the blade so as to cut
the brush into small pieces.
• Avoid hitting stones, piles of earth, small pieces of wood or anything that could be
hidden or dicult to see in the grass.
26L/U, 33L/U, 43U, 53U
18
Original Instructions Version June 16
Installing the Loop Handle Assembly (L Models)
• Fix the Clamp to the Drive Shaft, then pinch the flat lugs together on the underside of
the Clamp and slide them into the slot in the Lower Handle.
• Fit the Rubber Block and Upper Handle over the Clamp, ensuring the arrow on the
Upper Handle points towards the Cutter Head.
• Insert the Fixing Screw through the Upper Handle, Lower Handle and Clamp, do not
tighten.
• Adjust the handle to a comfortable working position then tighten the Fixing Screw.
Upper Handle
Rubber Block
Fixing Screw
Clamp
Lower Handle
Drive Shaft To
Cutter Head
Drive Shaft
To Engine
Ensure Arrow
Points Towards
Cutter Head
26L/U, 33L/U, 43U, 53U
19
Original Instructions Version June 16
Installing the U Handle Assembly (U Models)
• Remove the upper bracket from the assembly by undoing the 4 bolts.
• Install the U handle assembly, reassemble the bracket assembly and secure using the
4 bolts .
• Ensure that the controls are located on the right and adjust the handle for maximum
comfort before securing.
Bolts
Upper Bracket
Left handle
Right handle
Lower Bracket
Drive Shaft To
Cutter Head
Drive Shaft
To Engine
26L/U, 33L/U, 43U, 53U
20
Original Instructions Version June 16
Operation
Keep clear of the cutter head as it may start moving when the engine starts.
Starting the Engine
CAUTION do not pull the starter cord all the way out and do not let go of the starter handle when
the cord is extended, this can damage the starter mechanism.
Cold Engine Starting
Rest the unit on a flat, firm surface. Keep the cutting head o the ground and clear of surrounding
objects as it may start moving when starting the engine.
Fig 4 - While holding the unit, pull out
the starter rope firmly until engine fires
(indicated by a ‘cough’ from the engine).
Fig 3 - Set the ignition switch (d) to the
START (I) position.
Fig 2 - Move the choke lever (c) to the
START ( ) position.
Fig 1 - Push the air purge bulb (a) until
fuel is visible in the clear return fuel
line (b)
(a)
(b)
ST
A
RT
RUN
STOP
COLD
ST
ART:
(c)
(d)
26L/U, 33L/U, 43U, 53U
21
Original Instructions Version June 16
Allow the engine to warm up before use. When cutting, always use the Brushcutter on
full throttle.
Hot Engine Starting
• Set the ignition switch to the START ( I ) position.
• Check the clear return fuel line. If the line is empty, push the air purge bulb until fuel is
visible in the clear return fuel line.
• Move the choke lever to the START ( ) position, then back to the RUN ( )
position. This will set the throttle to the hot start position.
• Pull the starter rope until the engine starts, then squeeze the throttle briefly to release
the fast idle control and return the engine to idle.
• If the engine does not start after 5 pulls, use the Cold Start procedure.
Overchoking
Should the engine become flooded due to overchoking, turn the ignition switch o, unscrew the
spark plug, wipe it dry or replace.
Stopping the Engine
Set the engine to idling by releasing the throttle lever.
Set the ignition switch to the o position ‘’O’’ (STOP).
If the engine fails to stop, set the choke lever to the closed position to stall the engine; do not use
the machine until the ignition switch is repaired.
NOTE
Fig 6 - Pull the starter rope until the engine
starts, then squeeze the throttle briefly to
release the fast idle control and return the
engine to idle.
Fig 5 - Move the choke lever (e) to the
RUN ( ) position.
ST
ART
RUN
STOP
COLD
(e)
26L/U, 33L/U, 43U, 53U
22
Original Instructions Version June 16
Running In
During the first ten hours of work, avoid running the engine at maximum speed for a prolonged
period until all the components have bedded in, after the engine has been run in, it will reach its
maximum power.
Transportation
Never transport the Brushcutter with the engine running. An engine that is running could
be accidently accelerated causing the blade to engage.
Make sure the blade safety guards are in place when transporting the Brushcutter.
When carrying by hand, the cutting head should be pointing backwards.
Ensure the Brushcutter is secure when transporting in a vehicle and the tank is drained of fuel.
Maintenance
IMPORTANT
After every use, check that all nuts, bolts and screws are securely fastened and tighten if
necessary.
In the event of an accident, breakdown or blockage, ensure the engine is turned o before any
work is carried out to rectify this.
Make sure the engine has stopped and is cool before performing any service to the machine.
Contact with moving cutting head or hot muer may result in a personal injury.
Fuel Filter
Every 15 hours of operation, using a wire hook, take the fuel filter from the fuel tank and clean or
replace with a new fuel filter.
26L/U, 33L/U, 43U, 53U
23
Original Instructions Version June 16
Spark Plug
Poor starting or misfiring is often caused by a fouled or defective spark plug, clean and reset the
gap to 0.65 mm, or replace the spark plug with RCJ7Y (Champion) as necessary.
Air Filter
Before using the Brushcutter, check the air filter (a). Being clogged, will reduce the engine
performance.
Remove the air filter cover by pressing on the filter cover release (b) and opening the filter
cover (c). Clean the filter element in warm, soapy water, dry completely before installing. If the
element is broken or shrunk, replace with a new one.
0.6 - 0.7mm
(b)
(c)
(a)
26L/U, 33L/U, 43U, 53U
24
Original Instructions Version June 16
Carburettor
The carburettor mixture setting has been set at the factory and will not need adjusting.
Adjusting the idle speed: If adjustment is necessary turn the T screw (a) clockwise until the
cutting head starts to move, then turn the screw T anticlockwise until the cutting head stops.
If the idle speed cannot be adjusted to stop the cutting head moving at idle, contact
your dealer for repair before use.
Safety Lock
The safety lock is to prevent the throttle lever from accidentally being engaged. The throttle lever
(b) can only be pressed in if the safety lock (c) is held down. Check if the safety lock and throttle
lever returns to its original position and the engine returns to idling when you release your hand
from the handle.
Any defects contact your nearest service agent for repairs before using the machine.
(b)
(c)
(b)
(c)
(a)
26L/U, 33L/U, 43U, 53U
25
Original Instructions Version June 16
Storage
• Remove the spark plug; pour a small amount of oil into the cylinder. Rotate the
crankshaft several times using the starting rope in order to distribute the oil. Put the
spark plug back in.
• Remove the fuel from the machine.
Gear Case
• Remove the bolt (a) on the gear case, top up the gearbox using Lithium grease and refit
the bolt, every 15 hours use.
(a)
26L/U, 33L/U, 43U, 53U
26
Original Instructions Version June 16
Replacing the Nylon Cord
Check to see if the nylon head is damaged before replacing the cord. If you can see serious traces
of wear or damage, you must replace the complete nylon head.
1. Stop the engine.
2. Open the nylon head by pushing on the catch, (a), and lifting the cover (b).
3. Pull the bobbin out of the nylon head and take out the rest of the nylon cords.
4. Cut a new length of cord, 2.4mm Ø and 5 metres long.
5. Fold the new cord in half and place the centre of the fold (c) into the clip (d) in the empty bobbin.
6. Wind the line in the direction of the arrows on the bobbin, with half of the line above and half
below the divider (e). Maintain an even and firm tension onto the bobbin, being careful not to twist
the line.
6. After winding the cord, insert both ends into the notches on the bobbin, (f).
7. Put the filled bobbin back into the carrier. Release the cords from the notches in the bobbin
and thread them into the eyelets in the carrier (g). The cords should stick out appx 15 cm either
side.
8. Refit the spool cover (b), ensuring it is securely clicked into place.
**NOTE** To watch a video on fitting the nylon cutting line visit www.mitox.co.uk
Never use a cutting device other than those supplied by the manufacturer. (Steel cord is never
allowed) Always use original spare parts in order to benefit from continuous warranty.
(a)
(b)
(g)
(f)
(c)
(d)
(e)
(g)
(f)
26L/U, 33L/U, 43U, 53U
27
Original Instructions Version June 16
Troubleshooting
Engine will not start, power loss:
• Check that the fuel tank is not empty. Fill with mixed fuel.
• The fuel does not reach the carburettor. Change the fuel filter in the fuel tank.
• There is water in the fuel. Drain and clean the fuel system.
• The air filter is dirty. Clean or replace the air filter.
• There are carbon deposits in the exhaust muer restricting the engine. Clean or change
the muer.
• Spark plug is worn. Replace spark plug.
26L/U, 33L/U, 43U, 53U
28
Original Instructions Version June 16
Service Schedule
Component Procedure Before
use
Every 15
Hours
Every 25
Hours
Every 50
Hours
Note
Fuel leaks /
spillage
Wipe up
X
Fuel tank, filter Inspect /
clean
X
Replace if
necessary
Idle adjust
screw
See p.24
X X
Adjust
carburettor
if necessary
Spark plug
RCJ7Y
Clean and
readjust
plug gap X
GAP .025”
(0.6-
0.7mm)
Replace, if
necessary
Cylinder fins,
Intake air cooling vent
Clean
X
Muer, Spark
arrestor, cylinder exhaust
port
Clean
X
Throttle lever,
ignition switch
Check
operation
X
Air filter Clean
X
Screws, nuts,
bolts
Tighten /
replace X
Not
adjustment
screws
Grease the
gear box
Check
X
26L/U, 33L/U, 43U, 53U
29
Original Instructions Version June 16
Specifications
Model 26L SELECT 26U SELECT
Engine type 1E34F-4 (air cooled 2-stroke petrol engine)
Power (max.) 0.75Kw
Engine displacement 25.4cc
Idling speed 3100 ± 300
Engine maximum speed no load Grass Trimmer 9000 rpm
Cutting diameter Nylon Head 430mm - 3 Tooth Blade 255mm
Cutting Line Diameter 2.4mm
Blade Centre Hole 25.4mm
Fuel Mixture (Petrol 40: Oil 1)
Fuel tank Volumes 0.9L
Net weight (without fuel/harness) 6.3 6.3
Noise LWA dB(A) 110.4
Spark plug RCJ7Y (Champion)
Carburetor Diaphragm Type
Model 33L SELECT 33U SELECT
Engine type 1E36F-2 (air cooled 2-stroke petrol engine)
Power (max.) 1.0Kw
Engine displacement 32.6cc
Idling speed 3100 ± 300
Engine maximum speed no load Grass Trimmer 9000 rpm
Cutting diameter Nylon Head 430mm - 3 Tooth Blade 255mm
Cutting Line Diameter 2.4mm
Blade Centre Hole 25.4mm
Fuel Mixture (Petrol 40: Oil 1)
Fuel tank Volumes 0.9L
Net weight (without fuel/harness) 7.1 7.1
Noise LWA dB(A) 109.7
Spark plug RCJ7Y (Champion)
Carburetor Diaphragm Type
26L/U, 33L/U, 43U, 53U
30
Original Instructions Version June 16
Specifications
Model 43U SELECT
Engine type 1E40F-5 (air cooled 2-stroke petrol engine)
Power (max.) 1.25Kw
Engine displacement 42.7cc
Idling speed 3100 ± 300
Engine maximum speed no load Grass Trimmer 8500 rpm
Cutting diameter Nylon Head 430mm - 3 Tooth Blade 255mm
Cutting Line Diameter 2.4mm
Blade Centre Hole 25.4mm
Fuel Mixture (Petrol 40: Oil 1)
Fuel tank Volumes 1.0L
Net weight (without fuel/harness) 7.9
Noise LWA dB(A) 110.0
Spark plug RCJ7Y (Champion)
Carburetor Diaphragm Type
Specifications
Model 53U SELECT
Engine type 1E44F-6 (air cooled 2-stroke petrol engine)
Power (max.) 1.5Kw
Engine displacement 51.7cc
Idling speed 3100 ± 300
Engine maximum speed no load Grass Trimmer 8500 rpm
Cutting diameter Nylon Head 430mm - 3 Tooth Blade 255mm
Cutting Line Diameter 2.4mm
Blade Centre Hole 25.4mm
Fuel Mixture (Petrol 40: Oil 1)
Fuel tank Volumes 1.0L
Net weight (without fuel/harness) 8.0
Noise LWA dB(A) 110.4
Spark plug RCJ7Y (Champion)
Carburetor Diaphragm Type
26L/U, 33L/U, 43U, 53U
31
Original Instructions Version June 16
Notes
26L/U, 33L/U, 43U, 53U
32
Original Instructions Version June 16
Engine Parts Drawing: 26L
26L/U, 33L/U, 43U, 53U
33
Original Instructions Version June 16
Engine Parts List: 26L
48 MITBC330D.01.00.00-6 PLASTIC PLATE 1
49 MIGB/T119.2 5X10 PIN 5X10 2
50 MITBC331D.01.01.00-4 FAN COVER 1
51 MIGB/T2671.2 M5X20 SCREW M5X20 4
52 MITBC430D.01.14.01-00 CLUTCH DRUM 1
53 MIGB/T893.1 35 CIRCLIP (SIZE 35) 1
54 MIGB/T276 6202-2Z BEARING 6202 1
55 MIGB/T894.1 15 STOP RING (SIZE 15) 1
56 MITBC331D.01.14.00-1 CLUTCH DRUM HOUSING 1
57 MIGB/T2671.2 M6X20 SCREW M6X20 4
58 MITBC430D.01.14.00-2 ANTIVIBE RUBBER 1
59 MITBC430D.01.14.00-4 CLAMP RH 1
60 MITBC430D.01.14.00-3 CLAMP LH 1
61 MIGB/T2671.2 M5X25 SCREW M5X25 2
62 MIGB/T2671.2 M5X12 SCREW M5X12 1
63 MIGB/T2671.2 M5X60 SCREW M5X60-10 2
64 MIGB/T2671.2 M5X12 SCREW M5X12 1
65 MITBC331D.01.00.00-7 MUFFLER COVER 1
66 MITBC330D.01.09.00-00 MUFFLER 1
67 MITBC331D.01.00.00-10 GASKET - MUFFLER 1
68 MITBC330D.01.00.00-5 GASKET - MUFFLER 1
69 MIGB/T2671.2 M5X12 SCREW M5X12 1
70 MIGB/T2671.2 M4X12 SCREW M4X12 1
71 MITBC330D.01.00.00-3 GASKET 1
72 MITBC331D.01.00.01-00 MANIFOLD 1
73 MITBC431D.01.00.00-12 STRAP 1
74 MIGB/T845 ST3.5X9.5 ST SCREW 3.5X9.5 1
75 MIGB/T2671.2 M5X22 SCREW M5X22 2
76 MIYD38-3.01.00-8 CARBURETTOR GASKET 1
77 MITBC331D.01.06.00-00 CARBURETOR 1
78 MITBC331D.01.08.00-00 AIR FILTER ASSEMBLY 1
79 MITBC431D.01.08.00-1 AIR BOX BASE 1
80 MIGB/T2671.2 M5X45 SCREW M5X45 2
81 MITBC431D.01.08.00-3 AIR FILTER 1
82 MITBC331D.01.08.00-2 AIR BOX COVER 1
83 MITBC431D.01.13.01 FUEL CAP ASSY 1
86 MITBC331D.01.13.00-1 TANK 1
87 MITBC431D.01.13.00-2 FUEL TANK RUBBER 4
88 MITBC331D.01.00.00-8 FUEL TANK BRACKET 1
89 MIGB/T2671.2 M5X25 SCREW M5X25 4
90 MIA45.0111.0200 VENT VALVE 1
91 MITBC431D.01.13.00-6 BREATHER PIPE 1
92 MITBC430D.01.13.00-4 FUEL PIPE 1
93 MITBC430D.01.13.00-5 RETURN PIPE 1
94 MIC43.1107.0003 FUEL GROMME T 1
95 MIA45.0102.0103 CIRCLIP 1
96 MIA38.0311.0500 FUEL FILTER 1
ID PART NUMBER DESCRIPTION QTY
1 MIGB/T2671.2 M5X20 SCREW M5X20 2
2 MIGB/T2671.2 M5X25 SCREW M5X25 2
3 MIYD62.02.00-3 STARTER HANDLE 1
4 MIYD25.02.01-2 ROPE GUIDE 1
6 MITBC431D.01.12.00-00 STARTER ASSEMBLY 1
7 MITBC430D.01.12.00-2 STARTER ROPE 1
8 MITBC430D.01.12.00-4 RECOIL SPRING 1
9 MITBC431D.01.12.00-3 STARTER PULLEY 1
10 MITBC430D.01.12.00-5 SPRING - STARTER 1
11 MITBC431D.01.12.00-6 RATCHET WHEEL 1
12 MIGB/T9074.19 ST4.8X19 ST SCREW 4.8X19 1
13 MIGB/T9074.19 5X16X1 PLATE WASHER 5X16X1 1
14 MITBC430D.01.00.00-6 STARTER GASKET 1
15 MIGB/T6175 M8 NUT M8 1
16 MITBC430D.01.00.02-00 STARTER RATCHET ASSY 1
17 MIGB/T97.1 M8 FLAT WASHER M8 1
18 MIYD38-3.01.01.02-00 OIL SEAL 12X22X7 1
19 MITBC330D.01.01.00-2 CRANKCASE RH 1
20 MITBC330D.01.01.00-3 GASKET - CRANKCASE 1
21 MIGB/T276 6201 BALL BEARING 6201 2
22 MITBC331D.01.03.01-00 CRANK SHAFT ASS'Y 1
23 MIGB/T1099 3X5X13 KEY 3X5X13 1
24 MITBC330D.01.03.03-00 BEARING 1
25 MITBC330D.01.03.00-3 CIRCLIP \ PISTON PIN 2
26 MITBC330D.01.03.00-2 PISTON PIN 1
27 MITBC330D.01.03.02-00 PISTON 1
28 MITBC330D.01.03.00-1 PISTON RING 2
29 MITBC330D.01.00.00-2 GASKET - CYLINDER 1
30 MITBC331D.01.00.00-1 CYLINDER 1
31 MIGB/T2671.2 M5X20 SCREW M5X20 4
32 SPBPMR7A SPARK PLUG (BPMR7A NGK) 1
33 MITBC331D.01.00.00-9 ENGINE COVER 1
34 MITBC330D.01.11.02-00 WIRE 1
35 MITBC431D.01.11.00-1 PLUG CAP 1
36 MIGB/T2671.2 M5X25 SCREW M5X25 2
37 MITBC330D.01.11.01-00 IGNITION COIL 1
38 MIGB/T119.2 5X10 PIN 5X10 2
39 MITBC330D.01.01.00-1 CRANKCASE LH 1
40 MIGB/T2671.2 M5X30 SCREW M5X30 4
41 MIYD38-3.01.01.02-00 OIL SEAL 12X22X7 1
42 MITBC330D.01.10.00-00 FLYWHEEL 1
43 MIGB/T6187 M8 FLANGE NUT M8 1
44 MITBC430D.01.00.00-9 FLAT WASHER 8X16X1.5 2
45 MITBC431D.01.00.04-00 CLUTCH ASSEMBLY 1
46 MIGB/T755 M10 SPRING WASHER 10 2
47 MITBC430D.01.00.00-8 BOLT - CLUTCH 2
26L/U, 33L/U, 43U, 53U
34
Original Instructions Version June 16
Appliance Parts Drawing: 26L
26L/U, 33L/U, 43U, 53U
35
Original Instructions Version June 16
Appliance Parts List: 26L
ID. PART No DESCRIPTION
1 MITBC431D.02.00-3 CLAMP 1
2 MITBC430D.03.02-00 HARNESS CLAMP LOOP 1
3 MIGB/T2671.2 M5X20 SCREW M5X20 1
4 MITBC430D.03.00-2 CLAMP 1
5 MIGB/T6170 M5 NUT M5 1
6 MITBC431S.03.01-00 OUTER SHAFT ASSEMBLY 1
9 MITBC431D.04.00-00 GEAR BOX ASSEMBLY 1
10 MIGB/T894.1 10 CIRCLIP (SIZE 10) 1
11 MIGB/T893.1 26 CIRCLIP (SIZE 26) 1
12 MIGB/T276 6000-2Z BALL BEARING 6000-2Z 2
13 MIC43.0116.0002 PINION 1
14 MITBC431D.04.00-1 GEARBOX 1
15 MIC43.0116.0007 TOP GUARD 1
16 MIGB/T70.1 M5X8 SCREW M5X8 3
17 MIGB/T276 6000-2Z BALL BEARING 6000-2Z 1
18 MIC43.0116.0004 GEAR 1
19 MITBC431D.04.00-3 GEAR SHAFT 1
20 MIGB/T276 6002-2Z BALL BEARING 6002-2Z 1
21 MIGB/T893.1 26 CIRCLIP (SIZE 26) 1
22 MITBC431D.04.00-6 BLADE CLAMP - LOWER 1
23 MITBC431D.04.00-5 BLADE CLAMP - UPPER 1
24 MITBC431D.04.00-8 NUT PROTECTOR 1
25 MIGB/T6177.2 M10X1.25 FLANGE NUT M10X1.25 LH 1
26 MIGB/T70.1 M6X12 SCREW M6X12 1
27 MIGB/T2671.2 M6X12 SCREW M6X12 1
28 MIGB/T2671.2 M6X25 SCREW M6X25 1
29 MITBC430D.03.00-1 DRIVE SHAFT 1
30 MITBC431D.06.01-1 SKIRT 1
31 MIGB/T845 ST4.8X13 TAPPING SCREW ST4.8X13 2
32 MITBC431D.06.00-2 LINE CUTTER 1
33 MITBC431D.06.02-00 DEBRIS GUARD 1
34 MIC43.1113.0102 SPACER 2
35 MITBC430D.06.00-1 CLAMP 26MM 1
36 MIGB/T2671.2 M6X20 SCREW M6X20 2
37 MITBC431S.05.01-1 FRONT HANDLE 1
38 MIGB/T6170 M5 NUT M5 2
39 MITBC431S.05.01-2 HANDLE BASE 1
ID. PART No DESCRIPTION
40 MITBC431S.05.01-3 HANDLE CLAMP 1
41 MITBC431S.05.01-4 HANDLE BAR 1
42 MIGB/T2671.2 M5X28 SCREW M5X28 2
43 MIGB/T93 M5 SPRING WASHER M5 2
44 MIGB/T97.1 5X12X1.5 PLATE WASHER 2
45 MIGB/T97.1 5X11X2 PLATE WASHER 1.5X11X2 1
46 MIGB/T97.1 5X12X1.5 PLATE WASHER 1
47 MIGB/T845 ST4.8X19 TAPPING SCREW ST4.8X19 2
48 MITBC022S.2.1 THROTTLE HANDLE LH 1
49 MITBC022S.2-7A FIXING CLAMP 1
50 MIGB/T70.1 M5X14 CAP HEAD SCREW M5X14 1
51 MITBC143S.05.02-12A/13A SWITCH WIRES 1
52 MITBC143S.05.02-11A CABLE SLEEVE 1
53 MITBC143S.05.02-10A THROT TLE CABLE ASSEMBLY 1
54 MITBC022S.2.2 THROTTLE HANDLE RH 1
55 MIGB/T845 ST4X10 SCREW ST4X10 4
56 MITBC022S.2-1 TRIGGER 1
57 MITBC022S.2-4 SPRING 1
58 MITBC022S.2-6 SPRING 1
59 MITBC022S.2-2 LOCK TRIGGER 1
60 MIGB/T70.1 M5X14 CAP HEAD SCREW M5X14 1
61 MITBC022S.2-7A FIXING CLAMP 1
62 MIYD38-3.01.11.04-00 ON/OFF SWITCH 1
63 MIC43.1311.0500 THR OTTLE ASSEMBLY 1
64 MITBC431D.02.00-2 BLADE COVER 1
65 MITBC430D.02.01-00 NYLON HEAD ASSEMBLY 1
66 MIC43.1100.0001 BLADE 1
67 MI00.07.06.0007 HARNESS - SINGLE STRAP 1
26L/U, 33L/U, 43U, 53U
36
Original Instructions Version June 16
Engine Parts Drawing: 26U
26L/U, 33L/U, 43U, 53U
37
Original Instructions Version June 16
Engine Parts List: 26U
48 MITBC330D.01.00.00-6 PLASTIC PLATE 1
49 MIGB/T119.2 5X10 PIN 5X10 2
50 MITBC331D.01.01.00-4 FAN COVER 1
51 MIGB/T2671.2 M5X20 SCREW M5X20 4
52 MITBC430D.01.14.01-00 CLUTCH DRUM 1
53 MIGB/T893.1 35 CIRCLIP (SIZE 35) 1
54 MIGB/T276 6202-2Z BEARING 6202 1
55 MIGB/T894.1 15 STOP RING (SIZE 15) 1
56 MITBC331D.01.14.00-1 CLUTCH DRUM HOUSING 1
57 MIGB/T2671.2 M6X20 SCREW M6X20 4
58 MITBC430D.01.14.00-2 ANTIVIBE RUBBER 1
59 MITBC430D.01.14.00-4 CLAMP RH 1
60 MITBC430D.01.14.00-3 CLAMP LH 1
61 MIGB/T2671.2 M5X25 SCREW M5X25 2
62 MIGB/T2671.2 M5X12 SCREW M5X12 1
63 MIGB/T2671.2 M5X60 SCREW M5X60-10 2
64 MIGB/T2671.2 M5X12 SCREW M5X12 1
65 MITBC331D.01.00.00-7 MUFFLER COVER 1
66 MITBC330D.01.09.00-00 MUFFLER 1
67 MITBC331D.01.00.00-10 GASKET - MUFFLER 1
68 MITBC330D.01.00.00-5 GASKET - MUFFLER 1
69 MIGB/T2671.2 M5X12 SCREW M5X12 1
70 MIGB/T2671.2 M4X12 SCREW M4X12 1
71 MITBC330D.01.00.00-3 GASKET 1
72 MITBC331D.01.00.01-00 MANIFOLD 1
73 MITBC431D.01.00.00-12 STRAP 1
74 MIGB/T845 ST3.5X9.5 ST SCREW 3.5X9.5 1
75 MIGB/T2671.2 M5X22 SCREW M5X22 2
76 MIYD38-3.01.00-8 CARBURETTOR GASKET 1
77 MITBC331D.01.06.00-00 CARBURETOR 1
78 MITBC331D.01.08.00-00 AIR FILTER ASSEMBLY 1
79 MITBC431D.01.08.00-1 AIR BOX BASE 1
80 MIGB/T2671.2 M5X45 SCREW M5X45 2
81 MITBC431D.01.08.00-3 AIR FILTER 1
82 MITBC331D.01.08.00-2 AIR BOX COVER 1
83 MITBC431D.01.13.01 FUEL CAP ASSY 1
86 MITBC331D.01.13.00-1 TANK 1
87 MITBC431D.01.13.00-2 FUEL TANK RUBBER 4
88 MITBC331D.01.00.00-8 FUEL TANK BRACKET 1
89 MIGB/T2671.2 M5X25 SCREW M5X25 4
90 MIA45.0111.0200 VENT VALVE 1
91 MITBC431D.01.13.00-6 BREATHER PIPE 1
92 MITBC430D.01.13.00-4 FUEL PIPE 1
93 MITBC430D.01.13.00-5 RE TURN PIPE 1
94 MIC43.1107.0003 FUEL GROMME T 1
95 MIA45.0102.0103 CIRCLIP 1
96 MIA38.0311.0500 FUEL FILTER 1
ID PART NUMBER DESCRIPTION QTY
1 MIGB/T2671.2 M5X20 SCREW M5X20 2
2 MIGB/T2671.2 M5X25 SCREW M5X25 2
3 MIYD62.02.00-3 STARTER HANDLE 1
4 MIYD25.02.01-2 ROPE GUIDE 1
6 MITBC431D.01.12.00-00 STARTER ASSEMBLY 1
7 MITBC430D.01.12.00-2 STARTER ROPE 1
8 MITBC430D.01.12.00-4 RECOIL SPRING 1
9 MITBC431D.01.12.00-3 STARTER PULLEY 1
10 MITBC430D.01.12.00-5 SPRING - STARTER 1
11 MITBC431D.01.12.00-6 RATCHET WHEEL 1
12 MIGB/T9074.19 ST4.8X19 ST SCREW 4.8X19 1
13 MIGB/T9074.19 5X16X1 PLATE WASHER 5X16X1 1
14 MITBC430D.01.00.00-6 STARTER GASKET 1
15 MIGB/T6175 M8 NUT M8 1
16 MITBC430D.01.00.02-00 STARTER RATCHET ASSY 1
17 MIGB/T97.1 M8 FLAT WASHER M8 1
18 MIYD38-3.01.01.02-00 OIL SEAL 12X22X7 1
19 MITBC330D.01.01.00-2 CRANKCASE RH 1
20 MITBC330D.01.01.00-3 GASKET - CRANKCASE 1
21 MIGB/T276 6201 BALL BEARING 6201 2
22 MITBC331D.01.03.01-00 CRANK SHAFT ASS'Y 1
23 MIGB/T1099 3X5X13 KEY 3X5X13 1
24 MITBC330D.01.03.03-00 BEARING 1
25 MITBC330D.01.03.00-3 CIRCLIP \ PISTON PIN 2
26 MITBC330D.01.03.00-2 PISTON PIN 1
27 MITBC330D.01.03.02-00 PISTON 1
28 MITBC330D.01.03.00-1 PISTON RING 2
29 MITBC330D.01.00.00-2 GASKET - CYLINDER 1
30 MITBC331D.01.00.00-1 CYLINDER 1
31 MIGB/T2671.2 M5X20 SCREW M5X20 4
32 SPBPMR7A SPARK PLUG (BPMR7A NGK) 1
33 MITBC331D.01.00.00-9 ENGINE COVER 1
34 MITBC330D.01.11.02-00 WIRE 1
35 MITBC431D.01.11.00-1 PLUG CAP 1
36 MIGB/T2671.2 M5X25 SCREW M5X25 2
37 MITBC330D.01.11.01-00 IGNITION COIL 1
38 MIGB/T119.2 5X10 PIN 5X10 2
39 MITBC330D.01.01.00-1 CRANKCASE LH 1
40 MIGB/T2671.2 M5X30 SCREW M5X30 4
41 MIYD38-3.01.01.02-00 OIL SEAL 12X22X7 1
42 MITBC330D.01.10.00-00 FLYWHEEL 1
43 MIGB/T6187 M8 FLANGE NUT M8 1
44 MITBC430D.01.00.00-9 FLAT WASHER 8X16X1.5 2
45 MITBC431D.01.00.04-00 CLUTCH ASSEMBLY 1
46 MIGB/T755 M10 SPRING WASHER 10 2
47 MITBC430D.01.00.00-8 BOLT - CLUTCH 2
26L/U, 33L/U, 43U, 53U
38
Original Instructions Version June 16
Appliance Parts Drawing: 26U
26L/U, 33L/U, 43U, 53U
39
Original Instructions Version June 16
Appliance Parts List: 26U
ID PART NUMBER DESCRIPTION QTY
1 MITBC431D.02.00-3 CLAMP 3
2 MITBC430D.03.02-00 HARNESS CLAMP LOOP 1
3 MIGB/T2671.2 M5X20 SCREW M5X20 1
4 MITBC430D.03.00-2 CLAMP 1
5 MIGB/T6170 M5 NUT M5 1
6 MITBC431S.03.01-00 OUTER SHAFT 1
9 MITBC431D.04.00-00 GEAR BOX ASSEMBLY 1
10 MIGB/T894.1 10 CIRCLIP (SIZE 10) 1
11 MIGB/T893.1 26 E CLIP (SIZE 26) 1
12 MIGB/T276 6000-2Z BALL BEARING 6000-2Z 2
13 MIC43.0116.0002 PINION 1
14 MITBC431D.04.00-1 GEAR BOX 1
15 MIC43.0116.0007 TOP GUARD 1
16 MIGB/T70.1 M5X8 SCREW M5X8 3
17 MIGB/T276 6000-2Z BALL BEARING 6000-2Z 1
18 MIC43.0116.0004 GEAR 1
19 MITBC431D.04.00-3 GEAR SHAFT 1
20 MIGB/T276 6002-2Z BALL BEARING 6002-2Z 1
21 MIGB/T893.1 26 E CLIP (SIZE 26) 1
22 MITBC431D.04.00-6 BLADE CLAMP - LOWER 1
23 MITBC431D.04.00-5 BLADE CLAMP - UPPER 1
24 MITBC431D.04.00-8 NUT PROTECTOR 1
25 GB/T6177.2 M10X1.25 NUT M10X1.25 1
26 MIGB/T70.1 M6X12 SCREW M6X12 1
27 MIGB/T2671.2 M6X12 SCREW M6X12 1
28 MIGB/T2671.2 M6X25 SCREW M6X25 1
29 MITBC430D.03.00-1 DRIVER SHAFT 1
30 MITBC431D.06.01-1 SKIRT 1
31 MIGB/T845 ST4.8X13 TAPPING SCREW ST4.8X13 2
32 MITBC431D.06.00-2 LINE CUTTER 1
33 MITBC431D.06.02-00 DEBRIS GUARD 1
ID PART NUMBER DESCRIPTION QTY
34 MIC43.1113.0102 SPACER 2
35 MITBC430D.06.00-1 CLAMP 26MM 1
36 MIGB/T2671.2 M6X20 SCREW M6X20 2
37 MITBC431D.05.00-2 RUBBER HANDLE 1
38 MITBC431D.05.00-1 AL TUBING 1
39 MIGB/T2671.2 M5X25 SCREW M5X25 4
40 MITBC431D.05.03-3 UPPER CLAMP 1
41 MITBC431D.05.03-1 MIDDLE CLAMP 1
42 MITBC431D.05.03-2 LOWER HANDLE CLAMP 1
43 MIGB/T2671.2 M5X25 SCREW M5X25 2
44 MITBC431D.05.01-00 CONTROL HANDLE ASSEMBLY 1
45 MIGB/T2671.2 M5X30 SCREW M5X30 1
46 MIGB/T97.1 M5 WASHER M5 1
47 MITBC431D.05.01-2 THROTTLE HOUSING LH 1
48 MITBC431D.05.01-5 LOCK TRIGGER 1
49 MITBC431D.05.01-7 CONDUIT 1
50 MITBC431D.05.07-00 WIRE CABLE A 1
51 MITBC431D.05.08-00 WIRE CABLE B 1
52 MITBC431D.05.05-00 THROTTLE CABLE ASSEMBLY 1
53 MIGB/T6170 M5 NUT M5 1
54 MIGB/T845 ST3.5X9.5 ST SCREW 3.5X9.5 2
55 MIGB/T845 ST4.2X10 ST SCREW 4.2X10 4
56 MITBC431D.05.01-1 THROTTLE HOUSING RH 1
57 MITBC431D.05.01-4 SPRING - TRIGGER 1
58 MITBC431D.05.01-3 TRIGGER 1
59 MITBC431D.05.01-6 SPRING - TRIGGER 1
60 MIYD38-3.01.11.04-00 ON/OFF SWITCH 1
61 MITBC431D.02.00-2 BLADE COVER 1
62 MITBC430D.02.01-00 NYLON HEAD ASSY 1
63 MIC43.1100.0001 BLADE 1
64 MI00.07.06.0008 HARNESS 1
26L/U, 33L/U, 43U, 53U
40
Original Instructions Version June 16
Engine Parts Drawing: 33L
26L/U, 33L/U, 43U, 53U
41
Original Instructions Version June 16
Engine Parts List: 33L
48 MITBC330D.01.00.00-6 PLASTIC PLATE 1
49 MIGB/T119.2 5X10 PIN 5X10 2
50 MITBC331D.01.01.00-4 FAN COVER 1
51 MIGB/T2671.2 M5X20 SCREW M5X20 4
52 MITBC430D.01.14.01-00 CLUTCH DRUM 1
53 MIGB/T893.1 35 CIRCLIP (SIZE 35) 1
54 MIGB/T276 6202-2Z BEARING 6202 1
55 MIGB/T894.1 15 STOP RING (SIZE 15) 1
56 MITBC331D.01.14.00-1 CLUTCH DRUM HOUSING 1
57 MIGB/T2671.2 M6X20 SCREW M6X20 4
58 MITBC430D.01.14.00-2 ANTIVIBE RUBBER 1
59 MITBC430D.01.14.00-4 CLAMP RH 1
60 MITBC430D.01.14.00-3 CLAMP LH 1
61 MIGB/T2671.2 M5X25 SCREW M5X25 2
62 MIGB/T2671.2 M5X12 SCREW M5X12 1
63 MIGB/T2671.2 M5X60 SCREW M5X60-10 2
64 MIGB/T2671.2 M5X12 SCREW M5X12 1
65 MITBC331D.01.00.00-7 MUFFLER COVER 1
66 MITBC330D.01.09.00-00 MUFFLER 1
67 MITBC331D.01.00.00-10 GASKET - MUFFLER 1
68 MITBC330D.01.00.00-5 GASKET - MUFFLER 1
69 MIGB/T2671.2 M5X12 SCREW M5X12 1
70 MIGB/T2671.2 M4X12 SCREW M4X12 1
71 MITBC330D.01.00.00-3 GASKET 1
72 MITBC331D.01.00.01-00 MANIFOLD 1
73 MITBC431D.01.00.00-12 STRAP 1
74 MIGB/T845 ST3.5X9.5 ST SCREW 3.5X9.5 1
75 MIGB/T2671.2 M5X22 SCREW M5X22 2
76 MIYD38-3.01.00-8 CARBURETTOR GASKET 1
77 MITBC331D.01.06.00-00 CARBURETOR 1
78 MITBC331D.01.08.00-00 AIR FILTER ASSEMBLY 1
79 MITBC431D.01.08.00-1 AIR BOX BASE 1
80 MIGB/T2671.2 M5X45 SCREW M5X45 2
81 MITBC431D.01.08.00-3 AIR FILTER 1
82 MITBC331D.01.08.00-2 AIR BOX COVER 1
83 MITBC431D.01.13.01 FUEL CAP ASSY 1
86 MITBC331D.01.13.00-1 TANK 1
87 MITBC431D.01.13.00-2 FUEL TANK RUBBER 4
88 MITBC331D.01.00.00-8 FUEL TANK BRACKET 1
89 MIGB/T2671.2 M5X25 SCREW M5X25 4
90 MIA45.0111.0200 VENT VALVE 1
91 MITBC431D.01.13.00-6 BREATHER PIPE 1
92 MITBC430D.01.13.00-4 FUEL PIPE 1
93 MITBC430D.01.13.00-5 RE TURN PIPE 1
94 MIC43.1107.0003 FUEL GROMME T 1
95 MIA45.0102.0103 CIRCLIP 1
96 MIA38.0311.0500 FUEL FILTER 1
ID PART NUMBER DESCRIPTION QTY
1 MIGB/T2671.2 M5X20 SCREW M5X20 2
2 MIGB/T2671.2 M5X25 SCREW M5X25 2
3 MIYD62.02.00-3 STARTER HANDLE 1
4 MIYD25.02.01-2 ROPE GUIDE 1
6 MITBC431D.01.12.00-00 STARTER ASSEMBLY 1
7 MITBC430D.01.12.00-2 STARTER ROPE 1
8 MITBC430D.01.12.00-4 RECOIL SPRING 1
9 MITBC431D.01.12.00-3 STARTER PULLEY 1
10 MITBC430D.01.12.00-5 SPRING - STARTER 1
11 MITBC431D.01.12.00-6 RATCHET WHEEL 1
12 MIGB/T9074.19 ST4.8X19 ST SCREW 4.8X19 1
13 MIGB/T9074.19 5X16X1 PLATE WASHER 5X16X1 1
14 MITBC430D.01.00.00-6 STARTER GASKET 1
15 MIGB/T6175 M8 NUT M8 1
16 MITBC430D.01.00.02-00 STARTER RATCHET ASSY 1
17 MIGB/T97.1 M8 FLAT WASHER M8 1
18 MIYD38-3.01.01.02-00 OIL SEAL 12X22X7 1
19 MITBC330D.01.01.00-2 CRANKCASE RH 1
20 MITBC330D.01.01.00-3 GASKET - CRANKCASE 1
21 MIGB/T276 6201 BALL BEARING 6201 2
22 MITBC331D.01.03.01-00 CRANK SHAFT ASS'Y 1
23 MIGB/T1099 3X5X13 KEY 3X5X13 1
24 MITBC330D.01.03.03-00 BEARING 1
25 MITBC330D.01.03.00-3 CIRCLIP \ PISTON PIN 2
26 MITBC330D.01.03.00-2 PISTON PIN 1
27 MITBC330D.01.03.02-00 PISTON 1
28 MITBC330D.01.03.00-1 PISTON RING 2
29 MITBC330D.01.00.00-2 GASKET - CYLINDER 1
30 MITBC331D.01.00.00-1 CYLINDER 1
31 MIGB/T2671.2 M5X20 SCREW M5X20 4
32 SPBPMR7A SPARK PLUG (BPMR7A NGK) 1
33 MITBC331D.01.00.00-9 ENGINE COVER 1
34 MITBC330D.01.11.02-00 WIRE 1
35 MITBC431D.01.11.00-1 PLUG CAP 1
36 MIGB/T2671.2 M5X25 SCREW M5X25 2
37 MITBC330D.01.11.01-00 IGNITION COIL 1
38 MIGB/T119.2 5X10 PIN 5X10 2
39 MITBC330D.01.01.00-1 CRANKCASE LH 1
40 MIGB/T2671.2 M5X30 SCREW M5X30 4
41 MIYD38-3.01.01.02-00 OIL SEAL 12X22X7 1
42 MITBC330D.01.10.00-00 FLYWHEEL 1
43 MIGB/T6187 M8 FLANGE NUT M8 1
44 MITBC430D.01.00.00-9 FLAT WASHER 8X16X1.5 2
45 MITBC431D.01.00.04-00 CLUTCH ASSEMBLY 1
46 MIGB/T755 M10 SPRING WASHER 10 2
47 MITBC430D.01.00.00-8 BOLT - CLUTCH 2
26L/U, 33L/U, 43U, 53U
42
Original Instructions Version June 16
Appliance Parts Drawing: 33L
26L/U, 33L/U, 43U, 53U
43
Original Instructions Version June 16
Appliance Parts List: 33L
ID. PART No DESCRIPTION
1 MITBC431D.02.00-3 CLAMP 1
2 MITBC430D.03.02-00 HARNESS CLAMP LOOP 1
3 MIGB/T2671.2 M5X20 SCREW M5X20 1
4 MITBC430D.03.00-2 CLAMP 1
5 MIGB/T6170 M5 NUT M5 1
6 MITBC431S.03.01-00 OUTER SHAFT ASSEMBLY 1
9 MITBC431D.04.00-00 GEAR BOX ASSEMBLY 1
10 MIGB/T894.1 10 CIRCLIP (SIZE 10) 1
11 MIGB/T893.1 26 CIRCLIP (SIZE 26) 1
12 MIGB/T276 6000-2Z BALL BEARING 6000-2Z 2
13 MIC43.0116.0002 PINION 1
14 MITBC431D.04.00-1 GEARBOX 1
15 MIC43.0116.0007 TOP GUARD 1
16 MIGB/T70.1 M5X8 SCREW M5X8 3
17 MIGB/T276 6000-2Z BALL BEARING 6000-2Z 1
18 MIC43.0116.0004 GEAR 1
19 MITBC431D.04.00-3 GEAR SHAFT 1
20 MIGB/T276 6002-2Z BALL BEARING 6002-2Z 1
21 MIGB/T893.1 26 CIRCLIP (SIZE 26) 1
22 MITBC431D.04.00-6 BLADE CLAMP - LOWER 1
23 MITBC431D.04.00-5 BLADE CLAMP - UPPER 1
24 MITBC431D.04.00-8 NUT PROTECTOR 1
25 MIGB/T6177.2 M10X1.25 FLANGE NUT M10X1.25 LH 1
26 MIGB/T70.1 M6X12 SCREW M6X12 1
27 MIGB/T2671.2 M6X12 SCREW M6X12 1
28 MIGB/T2671.2 M6X25 SCREW M6X25 1
29 MITBC430D.03.00-1 DRIVE SHAFT 1
30 MITBC431D.06.01-1 SKIRT 1
31 MIGB/T845 ST4.8X13 TAPPING SCREW ST4.8X13 2
32 MITBC431D.06.00-2 LINE CUTTER 1
33 MITBC431D.06.02-00 DEBRIS GUARD 1
34 MIC43.1113.0102 SPACER 2
35 MITBC430D.06.00-1 CLAMP 26MM 1
36 MIGB/T2671.2 M6X20 SCREW M6X20 2
37 MITBC431S.05.01-1 FRONT HANDLE 1
38 MIGB/T6170 M5 NUT M5 2
39 MITBC431S.05.01-2 HANDLE BASE 1
ID. PART No DESCRIPTION
40 MITBC431S.05.01-3 HANDLE CLAMP 1
41 MITBC431S.05.01-4 HANDLE BAR 1
42 MIGB/T2671.2 M5X28 SCREW M5X28 2
43 MIGB/T93 M5 SPRING WASHER M5 2
44 MIGB/T97.1 5X12X1.5 PLATE WASHER 2
45 MIGB/T97.1 5X11X2 PLATE WASHER 1.5X11X2 1
46 MIGB/T97.1 5X12X1.5 PLATE WASHER 1
47 MIGB/T845 ST4.8X19 TAPPING SCREW ST4.8X19 2
48 MITBC022S.2.1 THROTTLE HANDLE LH 1
49 MITBC022S.2-7A FIXING CLAMP 1
50 MIGB/T70.1 M5X14 CAP HEAD SCREW M5X14 1
51 MITBC143S.05.02-12A/13A SWITCH WIRES 1
52 MITBC143S.05.02-11A CABLE SLEEVE 1
53 MITBC143S.05.02-10A THROT TLE CABLE ASSEMBLY 1
54 MITBC022S.2.2 THROTTLE HANDLE RH 1
55 MIGB/T845 ST4X10 SCREW ST4X10 4
56 MITBC022S.2-1 TRIGGER 1
57 MITBC022S.2-4 SPRING 1
58 MITBC022S.2-6 SPRING 1
59 MITBC022S.2-2 LOCK TRIGGER 1
60 MIGB/T70.1 M5X14 CAP HEAD SCREW M5X14 1
61 MITBC022S.2-7A FIXING CLAMP 1
62 MIYD38-3.01.11.04-00 ON/OFF SWITCH 1
63 MIC43.1311.0500 THR OTTLE ASSEMBLY 1
64 MITBC431D.02.00-2 BLADE COVER 1
65 MITBC430D.02.01-00 NYLON HEAD ASSEMBLY 1
66 MIC43.1100.0001 BLADE 1
67 MI00.07.06.0007 HARNESS - SINGLE STRAP 1
26L/U, 33L/U, 43U, 53U
44
Original Instructions Version June 16
Engine Parts Drawing: 33U
26L/U, 33L/U, 43U, 53U
45
Original Instructions Version June 16
48 MITBC330D.01.00.00-6 PLASTIC PLATE 1
49 MIGB/T119.2 5X10 PIN 5X10 2
50 MITBC331D.01.01.00-4 FAN COVER 1
51 MIGB/T2671.2 M5X20 SCREW M5X20 4
52 MITBC430D.01.14.01-00 CLUTCH DRUM 1
53 MIGB/T893.1 35 CIRCLIP (SIZE 35) 1
54 MIGB/T276 6202-2Z BEARING 6202 1
55 MIGB/T894.1 15 STOP RING (SIZE 15) 1
56 MITBC331D.01.14.00-1 CLUTCH DRUM HOUSING 1
57 MIGB/T2671.2 M6X20 SCREW M6X20 4
58 MITBC430D.01.14.00-2 ANTIVIBE RUBBER 1
59 MITBC430D.01.14.00-4 CLAMP RH 1
60 MITBC430D.01.14.00-3 CLAMP LH 1
61 MIGB/T2671.2 M5X25 SCREW M5X25 2
62 MIGB/T2671.2 M5X12 SCREW M5X12 1
63 MIGB/T2671.2 M5X60 SCREW M5X60-10 2
64 MIGB/T2671.2 M5X12 SCREW M5X12 1
65 MITBC331D.01.00.00-7 MUFFLER COVER 1
66 MITBC330D.01.09.00-00 MUFFLER 1
67 MITBC331D.01.00.00-10 GASKET - MUFFLER 1
68 MITBC330D.01.00.00-5 GASKET - MUFFLER 1
69 MIGB/T2671.2 M5X12 SCREW M5X12 1
70 MIGB/T2671.2 M4X12 SCREW M4X12 1
71 MITBC330D.01.00.00-3 GASKET 1
72 MITBC331D.01.00.01-00 MANIFOLD 1
73 MITBC431D.01.00.00-12 STRAP 1
74 MIGB/T845 ST3.5X9.5 ST SCREW 3.5X9.5 1
75 MIGB/T2671.2 M5X22 SCREW M5X22 2
76 MIYD38-3.01.00-8 CARBURETTOR GASKET 1
77 MITBC331D.01.06.00-00 CARBURETOR 1
78 MITBC331D.01.08.00-00 AIR FILTER ASSEMBLY 1
79 MITBC431D.01.08.00-1 AIR BOX BASE 1
80 MIGB/T2671.2 M5X45 SCREW M5X45 2
81 MITBC431D.01.08.00-3 AIR FILTER 1
82 MITBC331D.01.08.00-2 AIR BOX COVER 1
83 MITBC431D.01.13.01 FUEL CAP ASSY 1
86 MITBC331D.01.13.00-1 TANK 1
87 MITBC431D.01.13.00-2 FUEL TANK RUBBER 4
88 MITBC331D.01.00.00-8 FUEL TANK BRACKET 1
89 MIGB/T2671.2 M5X25 SCREW M5X25 4
90 MIA45.0111.0200 VENT VALVE 1
91 MITBC431D.01.13.00-6 BREATHER PIPE 1
92 MITBC430D.01.13.00-4 FUEL PIPE 1
93 MITBC430D.01.13.00-5 RE TURN PIPE 1
94 MIC43.1107.0003 FUEL GROMME T 1
95 MIA45.0102.0103 CIRCLIP 1
96 MIA38.0311.0500 FUEL FILTER 1
Engine Parts List: 33U
ID PART NUMBER DESCRIPTION QTY
1 MIGB/T2671.2 M5X20 SCREW M5X20 2
2 MIGB/T2671.2 M5X25 SCREW M5X25 2
3 MIYD62.02.00-3 STARTER HANDLE 1
4 MIYD25.02.01-2 ROPE GUIDE 1
6 MITBC431D.01.12.00-00 STARTER ASSEMBLY 1
7 MITBC430D.01.12.00-2 STARTER ROPE 1
8 MITBC430D.01.12.00-4 RECOIL SPRING 1
9 MITBC431D.01.12.00-3 STARTER PULLEY 1
10 MITBC430D.01.12.00-5 SPRING - STARTER 1
11 MITBC431D.01.12.00-6 RATCHET WHEEL 1
12 MIGB/T9074.19 ST4.8X19 ST SCREW 4.8X19 1
13 MIGB/T9074.19 5X16X1 PLATE WASHER 5X16X1 1
14 MITBC430D.01.00.00-6 STARTER GASKET 1
15 MIGB/T6175 M8 NUT M8 1
16 MITBC430D.01.00.02-00 STARTER RATCHET ASSY 1
17 MIGB/T97.1 M8 FLAT WASHER M8 1
18 MIYD38-3.01.01.02-00 OIL SEAL 12X22X7 1
19 MITBC330D.01.01.00-2 CRANKCASE RH 1
20 MITBC330D.01.01.00-3 GASKET - CRANKCASE 1
21 MIGB/T276 6201 BALL BEARING 6201 2
22 MITBC331D.01.03.01-00 CRANK SHAFT ASS'Y 1
23 MIGB/T1099 3X5X13 KEY 3X5X13 1
24 MITBC330D.01.03.03-00 BEARING 1
25 MITBC330D.01.03.00-3 CIRCLIP \ PISTON PIN 2
26 MITBC330D.01.03.00-2 PISTON PIN 1
27 MITBC330D.01.03.02-00 PISTON 1
28 MITBC330D.01.03.00-1 PISTON RING 2
29 MITBC330D.01.00.00-2 GASKET - CYLINDER 1
30 MITBC331D.01.00.00-1 CYLINDER 1
31 MIGB/T2671.2 M5X20 SCREW M5X20 4
32 SPBPMR7A SPARK PLUG (BPMR7A NGK) 1
33 MITBC331D.01.00.00-9 ENGINE COVER 1
34 MITBC330D.01.11.02-00 WIRE 1
35 MITBC431D.01.11.00-1 PLUG CAP 1
36 MIGB/T2671.2 M5X25 SCREW M5X25 2
37 MITBC330D.01.11.01-00 IGNITION COIL 1
38 MIGB/T119.2 5X10 PIN 5X10 2
39 MITBC330D.01.01.00-1 CRANKCASE LH 1
40 MIGB/T2671.2 M5X30 SCREW M5X30 4
41 MIYD38-3.01.01.02-00 OIL SEAL 12X22X7 1
42 MITBC330D.01.10.00-00 FLYWHEEL 1
43 MIGB/T6187 M8 FLANGE NUT M8 1
44 MITBC430D.01.00.00-9 FLAT WASHER 8X16X1.5 2
45 MITBC431D.01.00.04-00 CLUTCH ASSEMBLY 1
46 MIGB/T755 M10 SPRING WASHER 10 2
47 MITBC430D.01.00.00-8 BOLT - CLUTCH 2
26L/U, 33L/U, 43U, 53U
46
Original Instructions Version June 16
Appliance Parts Drawing: 33U
26L/U, 33L/U, 43U, 53U
47
Original Instructions Version June 16
Appliance Parts List: 33U
ID PART NUMBER DESCRIPTION QTY
1 MITBC431D.02.00-3 CLAMP 3
2 MITBC430D.03.02-00 HARNESS CLAMP LOOP 1
3 MIGB/T2671.2 M5X20 SCREW M5X20 1
4 MITBC430D.03.00-2 CLAMP 1
5 MIGB/T6170 M5 NUT M5 1
6 MITBC431S.03.01-00 OUTER SHAFT 1
9 MITBC431D.04.00-00 GEAR BOX ASSEMBLY 1
10 MIGB/T894.1 10 CIRCLIP (SIZE 10) 1
11 MIGB/T893.1 26 E CLIP (SIZE 26) 1
12 MIGB/T276 6000-2Z BALL BEARING 6000-2Z 2
13 MIC43.0116.0002 PINION 1
14 MITBC431D.04.00-1 GEAR BOX 1
15 MIC43.0116.0007 TOP GUARD 1
16 MIGB/T70.1 M5X8 SCREW M5X8 3
17 MIGB/T276 6000-2Z BALL BEARING 6000-2Z 1
18 MIC43.0116.0004 GEAR 1
19 MITBC431D.04.00-3 GEAR SHAFT 1
20 MIGB/T276 6002-2Z BALL BEARING 6002-2Z 1
21 MIGB/T893.1 26 E CLIP (SIZE 26) 1
22 MITBC431D.04.00-6 BLADE CLAMP - LOWER 1
23 MITBC431D.04.00-5 BLADE CLAMP - UPPER 1
24 MITBC431D.04.00-8 NUT PROTECTOR 1
25 GB/T6177.2 M10X1.25 NUT M10X1.25 1
26 MIGB/T70.1 M6X12 SCREW M6X12 1
27 MIGB/T2671.2 M6X12 SCREW M6X12 1
28 MIGB/T2671.2 M6X25 SCREW M6X25 1
29 MITBC430D.03.00-1 DRIVER SHAFT 1
30 MITBC431D.06.01-1 SKIRT 1
31 MIGB/T845 ST4.8X13 TAPPING SCREW ST4.8X13 2
32 MITBC431D.06.00-2 LINE CUTTER 1
33 MITBC431D.06.02-00 DEBRIS GUARD 1
ID PART NUMBER DESCRIPTION QTY
34 MIC43.1113.0102 SPACER 2
35 MITBC430D.06.00-1 CLAMP 26MM 1
36 MIGB/T2671.2 M6X20 SCREW M6X20 2
37 MITBC431D.05.00-2 RUBBER HANDLE 1
38 MITBC431D.05.00-1 AL TUBING 1
39 MIGB/T2671.2 M5X25 SCREW M5X25 4
40 MITBC431D.05.03-3 UPPER CLAMP 1
41 MITBC431D.05.03-1 MIDDLE CLAMP 1
42 MITBC431D.05.03-2 LOWER HANDLE CLAMP 1
43 MIGB/T2671.2 M5X25 SCREW M5X25 2
44 MITBC431D.05.01-00 CONTROL HANDLE ASSEMBLY 1
45 MIGB/T2671.2 M5X30 SCREW M5X30 1
46 MIGB/T97.1 M5 WASHER M5 1
47 MITBC431D.05.01-2 THROTTLE HOUSING LH 1
48 MITBC431D.05.01-5 LOCK TRIGGER 1
49 MITBC431D.05.01-7 CONDUIT 1
50 MITBC431D.05.07-00 WIRE CABLE A 1
51 MITBC431D.05.08-00 WIRE CABLE B 1
52 MITBC431D.05.05-00 THROTTLE CABLE ASSEMBLY 1
53 MIGB/T6170 M5 NUT M5 1
54 MIGB/T845 ST3.5X9.5 ST SCREW 3.5X9.5 2
55 MIGB/T845 ST4.2X10 ST SCREW 4.2X10 4
56 MITBC431D.05.01-1 THROTTLE HOUSING RH 1
57 MITBC431D.05.01-4 SPRING - TRIGGER 1
58 MITBC431D.05.01-3 TRIGGER 1
59 MITBC431D.05.01-6 SPRING - TRIGGER 1
60 MIYD38-3.01.11.04-00 ON/OFF SWITCH 1
61 MITBC431D.02.00-2 BLADE COVER 1
62 MITBC430D.02.01-00 NYLON HEAD ASSY 1
63 MIC43.1100.0001 BLADE 1
64 MI00.07.06.0008 HARNESS 1
26L/U, 33L/U, 43U, 53U
48
Original Instructions Version June 16
Engine Parts Drawing: 43U
26L/U, 33L/U, 43U, 53U
49
Original Instructions Version June 16
Engine Parts List: 43U
ID PART NUMBER DESCRIPTION QTY
1 MIGB/T2671.2 M5X20 SCREW M5X20 2
2 MIGB/T2671.2 M5X25 SCREW M5X25 2
3 MIA62.0110.0002 STARTER HANDLE 1
4 MIYD25.02.01-2 ROPE GUIDE 1
6 MITBC431D.01.12.00-00 STARTER ASSEMBLY 1
7 MITBC430D.01.12.00-2 STARTER ROPE 1
8 MITBC430D.01.12.00-4 RECOIL SPRING 1
9 MITBC431D.01.12.00-3 STARTER PULLEY 1
10 MITBC430D.01.12.00-5 SPRING - STARTER 1
11 MITBC431D.01.12.00-6 RATCHET WHEEL 1
12 MIGB/T9074.19 ST4.8X19 ST SCREW 4.8X19 1
13 MIGB/T9074.19 5X16X1 PLATE WASHER 5X16X1 1
14 MITBC430D.01.00.00-6 STARTER GASKET 1
15 MIGB/T6175 M8 NUT M8 1
16 MITBC430D.01.00.02-00 STARTER RATCHET ASSY 1
17 MIGB/T97.1 M8 FLAT WASHER M8 1
18 MIYD38-3.01.01.02-00 OIL SEAL 12X22X7 1
19 MITBC430D.01.01.00-2 CRANKCASE RH 1
20 MITBC430D.01.01.00-3 GASKET - CRANKCASE 1
21 MIGB/T276 6202 BALL BEARING 6202-2Z 2
22 MITBC430D.01.03.01-00 CRANKSHAFT 1
23 MIGB/T1099 3X5X13 KEY 3X5X13 1
24 MITBC430D.01.03.03-00 BEARING ?10X13X16 1
25 MIYD38-3.01.03.00-4 PISTON PIN CIRCLIP 2
26 MITBC430D.01.03.00-2 PISTON PIN 1
27 MITBC430D.01.03.02-00 PISTON 1
28 MITBC430D.01.03.00-1 PISTON RING 2
29 MITBC430D.01.00.00-2 GASKET - CYLINDER 1
30 MITBC431D.01.00.00-1 CYLINDER 1
31 MIGB/T2671.2 M5X20 SCREW M5X20 4
32 SPBPMR7A SPARK PLUG (BPMR7A NGK) 1
33 MITBC431D.01.00.00-11 ENGINE COVER 1
34 MITBC430D.01.11.02-00 WIRE 1
35 MITBC431D.01.11.00-1 PLUG CAP 1
36 MIGB/T2671.2 M5X25 SCREW M5X25 2
37 MITBC430D.01.11.01-00 IGNITION 1
38 MIGB/T119.2 5X10 PIN 5X10 2
39 MITBC430D.01.01.00-1 CRANKCASE LH 1
40 MIGB/T2671.2 M5X30 SCREW M5X30 4
41 MITBC430D.01.00.03-00 OIL-SEAL 15X30X7 1
42 MITBC430D.01.10.00-00 FLYWHEEL 1
43 MIGB/T6187 M8 FLANGE NUT M8 1
44 MITBC430D.01.00.00-9 FLAT WASHER 8X16X1.5 2
45 MITBC430D.01.00.04-00 CLUTCH ASSEMBLY 1
46 MIGB/T755 M10 SPRING WASHER 10 2
47 MITBC430D.01.00.00-8 BOLT - CLUTCH 2
48 MIGB/T119.2 5X10 PIN 5X10 2
49 MITBC431D.01.01.00-4 FAN COVER 1
50 MIGB/T2671.2 M5X25 SCREW M5X25 4
51 MITBC430D.01.14.01-00 CLUTCH DRUM 1
52 MIGB/T893.1 35 CIRCLIP (SIZE 35) 1
53 MIGB/T276 6202-2Z BEARING 6202 1
54 MIGB/T894.1 15 STOP RING (SIZE 15) 1
55 MITBC431D.01.14.00-1B CLUTCH HOUSING 1
56 MIGB/T2671.2 M6X20 SCREW M6X20 4
57 MITBC521D.01.14.00-2 ANTIVIBE RUBBER 1
58 MITBC521D.01.14.00-4 CLAMP RH 1
59 MITBC521D.01.14.00-3 CLAMP LH 1
60 MIGB/T2671.2 M5X25 SCREW M5X25 2
61 MIGB/T2671.2 M5X12 SCREW M5X12 1
62 MIGB/T2671.2 M6X55 SCREW M6X55 2
63 MIGB/T2671.2 M5X12 SCREW M5X12 1
64 MITBC431D.01.00.00-7 MUFFLER COVER 1
65 MIGB/T97.1 M6 FLAT WASHER M6 2
66 MITBC430D.01.09.00-00 MUFFLER 1
67 MITBC431D.01.00.00-13 GASKET - MUFFLER 1
68 MITBC430D.01.00.00-5 GASKET - MUFFLER 1
69 MIGB/T2671.2 M5X12 SCREW M5X12 1
70 MIGB/T2671.2 M4X12 SCREW M4X12 1
71 MITBC430D.01.00.00-3 GASKET 1
72 MITBC431D.01.00.01-00 MANIFOLD 1
73 MIGB/T845 ST3.5X9.5 ST SCREW 3.5X9.5 1
74 MITBC431D.01.00.00-12 STRAP 1
75 MIGB/T2671.2 M5X25 SCREW M5X25 2
76 MIYD38-3.01.00-8 CARBURETTOR GASKET 1
77 MITBC431D.01.06.00-00 CARBURETOR 1
78 MITBC431D.01.08.00-00 AIR FILTER ASSEMBLY 1
79 MITBC431D.01.08.00-1 AIR BOX BASE 1
80 MIGB/T2671.2 M5X45 SCREW M5X45 2
81 MITBC431D.01.08.00-3 AIR FILTER 1
82 MITBC431D.01.08.00-2 AIR BOX COVER 1
83 MITBC431D.01.13.01 FUEL CAP ASSY 1
86 MITBC431D.01.13.00-1 FUEL TANK 1
87 MITBC431D.01.13.00-2 FUEL TANK RUBBER 4
88 MITBC431D.01.00.00-10 FUEL TANK BRACKET 1
89 MIGB/T2671.2 M5X25 SCREW M5X25 4
90 MIYD45.03.04-00 BREATHER ASSY 1
91 MITBC431D.01.13.00-6 BREATHER PIPE 1
92 MITBC431D.01.13.00-4 FUEL PIPE 1
93 MITBC431D.01.13.00-5 FUEL PIPE 1
94 MITBC431D.01.13.00-3 GROMME T 1
95 MIYD45.01.01.01-3 CIRCLIP 1
96 MIYD38-3.03.04-00 FUEL FILTER 1
26L/U, 33L/U, 43U, 53U
50
Original Instructions Version June 16
Appliance Parts Drawing: 43U
26L/U, 33L/U, 43U, 53U
51
Original Instructions Version June 16
Appliance Parts List: 43U
ID PART NUMBER DESCRIPTION QTY
1 MITBC431D.02.00-3 CLAMP 3
2 MITBC430D.03.02-00A HARNESS CLAMP 1
3 MIGB/T2671.2 M5X20 SCREW M5X20 1
4 MITBC430D.03.00-2A RETAINER CLIP 1
5 MIGB/T6170 M5 NUT M5 1
6 MITBC431D.03.01-00A OUTER SHAFT ASSEMBLY 1
9 MITBC431D.04.00-00A GEAR BOX ASSEMBLY 1
10 MIGB/T894.1 10 CIRCLIP (SIZE 10) 1
11 MIGB/T893.1 26 E CLIP (SIZE 26) 1
12 MIGB/T276 6000-2Z BALL BEARING 6000-2Z 2
13 MIC43.0116.0002 PINION 1
14 MITBC431D.04.00-1A GEAR BOX 1
15 MIC43.0116.0007 TOP GUARD 1
16 MIGB/T70.1 M5X8 SCREW M5X8 3
17 MIGB/T276 6000-2Z BALL BEARING 6000-2Z 1
18 MIC43.0116.0004 GEAR 1
19 MITBC431D.04.00-3 GEAR SHAFT 1
20 MIGB/T276 6002-2Z BALL BEARING 6002-2Z 1
21 MIGB/T893.1 26 E CLIP (SIZE 26) 1
22 MITBC431D.04.00-6 BLADE CLAMP - LOWER 1
23 MITBC431D.04.00-5 BLADE CLAMP - UPPER 1
24 MITBC431D.04.00-8 NUT PROTECTOR 1
25 MIGB/T6177.2 M10X1.25 FLANGE NUT M10X1.25 1
26 MIGB/T70.1 M6X12 SCREW M6X12 1
27 MIGB/T2671.2 M6X12 SCREW M6X12 1
28 MIGB/T2671.2 M6X25 SCREW M6X25 1
29 MITBC430D.03.00-1 DRIVER SHAFT 1
30 MITBC431D.06.01-1 SKIRT 1
31 MIGB/T845 ST4.8X13 TAPPING SCREW ST4.8X13 2
32 MITBC431D.06.00-2 LINE CUTTER 1
33 MITBC431D.06.02-00 DEBRIS GUARD 1
ID PART NUMBER DESCRIPTION QTY
34 MIC43.1113.0102 SPACER 2
35 MITBC431D.06.00-1A GUARD CLAMP 1
36 MIGB/T2671.2 M6X20 SCREW M6X20 2
37 MITBC431D.05.00-2A RUBBER HANDLE 1
38 MITBC431D.05.00-1A AL TUBING 1
39 MIGB/T2671.2 M5X25 SCREW M5X25 4
40 MITBC431D.05.03-3A UPPER CLAMP 1
41 MITBC431D.05.03-1A MIDDLE CLAMP 1
42 MITBC431D.05.03-2A LOWER CLAMP 1
43 MIGB/T2671.2 M5X25 SCREW M5X25 2
44 MITBC431D.05.01-00A CONTROL HANDLE ASSEMBLY 1
45 MIGB/T2671.2 M5X30 SCREW M5X30 1
46 MIGB/T97.1 M5 WASHER M5 1
47 MITBC431D.05.01-2A THROTTLE HOUSING LH 1
48 MITBC431D.05.01-5 LOCK TRIGGER 1
49 MITBC431D.05.01-7 CONDUIT 1
50 MITBC431D.05.07-00 WIRE CABLE A 1
51 MITBC431D.05.08-00 WIRE CABLE B 1
52 MITBC431D.05.05-00 THROTTLE CABLE ASSEMBLY 1
53 MIGB/T6170 M5 NUT M5 1
54 MIGB/T845 ST3.5X9.5 ST SCREW 3.5X9.5 2
55 MIGB/T845 ST4.2X10 ST SCREW 4.2X10 4
56 MITBC431D.05.01-1A THROTTLE HOUSING RH 1
57 MITBC431D.05.01-4 SPRING - TRIGGER 1
58 MITBC431D.05.01-3 TRIGGER 1
59 MITBC431D.05.01-6 SPRING - TRIGGER 1
60 MIYD38-3.01.11.04-00 ON/OFF SWITCH 1
61 MITBC431D.02.00-2 BLADE COVER 1
62 MITBC430D.02.01-00 NYLON HEAD ASSY 1
63 MIC43.1100.0001 BLADE 1
64 MI00.07.06.0008 HARNESS 1
26L/U, 33L/U, 43U, 53U
52
Original Instructions Version June 16
Engine Parts Drawing: 53U
26L/U, 33L/U, 43U, 53U
53
Original Instructions Version June 16
Engine Parts List: 53U
ID PART NUMBER DESCRIPTION QTY
1 MIGB/T2671.2 M5X20 SCREW M5X20 2
2 MIGB/T2671.2 M5X25 SCREW M5X25 2
3 MIA62.0110.0002 STARTER HANDLE 1
4 MIYD25.02.01-2 ROPE GUIDE 1
6 MITBC431D.01.12.00-00 STARTER ASSEMBLY 1
7 MITBC430D.01.12.00-2 STARTER ROPE 1
8 MITBC430D.01.12.00-4 RECOIL SPRING 1
9 MITBC431D.01.12.00-3 STARTER PULLEY 1
10 MITBC430D.01.12.00-5 SPRING - STARTER 1
11 MITBC431D.01.12.00-6 RATCHET WHEEL 1
12 MIGB/T9074.19 ST4.8X19 ST SCREW 4.8X19 1
13 MIGB/T9074.19 5X16X1 PLATE WASHER 5X16X1 1
14 MITBC430D.01.00.00-6 STARTER GASKET 1
15 MIGB/T6175 M8 NUT M8 1
16 MITBC430D.01.00.02-00 STARTER RATCHET ASSY 1
17 MIGB/T97.1 M8 FLAT WASHER M8 1
18 MIYD38-3.01.01.02-00 OIL SEAL 12X22X7 1
19 MITBC430D.01.01.00-2 CRANKCASE RH 1
20 MITBC430D.01.01.00-3 GASKET - CRANKCASE 1
21 MIGB/T276 6202 BALL BEARING 6202-2Z 2
22 MITBC430D.01.03.01-00 CRANKSHAFT 1
23 MIGB/T1099 3X5X13 KEY 3X5X13 1
24 MITBC430D.01.03.03-00 BEARING ?10X13X16 1
25 MIYD38-3.01.03.00-4 PISTON PIN CIRCLIP 2
26 MITBC430D.01.03.00-2 PISTON PIN 1
27 MITBC430D.01.03.02-00 PISTON 1
28 MITBC430D.01.03.00-1 PISTON RING 2
29 MITBC430D.01.00.00-2 GASKET - CYLINDER 1
30 MITBC431D.01.00.00-1 CYLINDER 1
31 MIGB/T2671.2 M5X20 SCREW M5X20 4
32 SPBPMR7A SPARK PLUG (BPMR7A NGK) 1
33 MITBC431D.01.00.00-11 ENGINE COVER 1
34 MITBC430D.01.11.02-00 WIRE 1
35 MITBC431D.01.11.00-1 PLUG CAP 1
36 MIGB/T2671.2 M5X25 SCREW M5X25 2
37 MITBC430D.01.11.01-00 IGNITION 1
38 MIGB/T119.2 5X10 PIN 5X10 2
39 MITBC430D.01.01.00-1 CRANKCASE LH 1
40 MIGB/T2671.2 M5X30 SCREW M5X30 4
41 MITBC430D.01.00.03-00 OIL-SEAL 15X30X7 1
42 MITBC430D.01.10.00-00 FLYWHEEL 1
43 MIGB/T6187 M8 FLANGE NUT M8 1
44 MITBC430D.01.00.00-9 FLAT WASHER 8X16X1.5 2
45 MITBC430D.01.00.04-00 CLUTCH ASSEMBLY 1
46 MIGB/T755 M10 SPRING WASHER 10 2
47 MITBC430D.01.00.00-8 BOLT - CLUTCH 2
48 MIGB/T119.2 5X10 PIN 5X10 2
49 MITBC431D.01.01.00-4 FAN COVER 1
50 MIGB/T2671.2 M5X25 SCREW M5X25 4
51 MITBC430D.01.14.01-00 CLUTCH DRUM 1
52 MIGB/T893.1 35 CIRCLIP (SIZE 35) 1
53 MIGB/T276 6202-2Z BEARING 6202 1
54 MIGB/T894.1 15 STOP RING (SIZE 15) 1
55 MITBC431D.01.14.00-1B CLUTCH HOUSING 1
56 MIGB/T2671.2 M6X20 SCREW M6X20 4
57 MITBC521D.01.14.00-2 ANTIVIBE RUBBER 1
58 MITBC521D.01.14.00-4 CLAMP RH 1
59 MITBC521D.01.14.00-3 CLAMP LH 1
60 MIGB/T2671.2 M5X25 SCREW M5X25 2
61 MIGB/T2671.2 M5X12 SCREW M5X12 1
62 MIGB/T2671.2 M6X55 SCREW M6X55 2
63 MIGB/T2671.2 M5X12 SCREW M5X12 1
64 MITBC431D.01.00.00-7 MUFFLER COVER 1
65 MIGB/T97.1 M6 FLAT WASHER M6 2
66 MITBC430D.01.09.00-00 MUFFLER 1
67 MITBC431D.01.00.00-13 GASKET - MUFFLER 1
68 MITBC430D.01.00.00-5 GASKET - MUFFLER 1
69 MIGB/T2671.2 M5X12 SCREW M5X12 1
70 MIGB/T2671.2 M4X12 SCREW M4X12 1
71 MITBC430D.01.00.00-3 GASKET 1
72 MITBC431D.01.00.01-00 MANIFOLD 1
73 MIGB/T845 ST3.5X9.5 ST SCREW 3.5X9.5 1
74 MITBC431D.01.00.00-12 STRAP 1
75 MIGB/T2671.2 M5X25 SCREW M5X25 2
76 MIYD38-3.01.00-8 CARBURETTOR GASKET 1
77 MITBC431D.01.06.00-00 CARBURETOR 1
78 MITBC431D.01.08.00-00 AIR FILTER ASSEMBLY 1
79 MITBC431D.01.08.00-1 AIR BOX BASE 1
80 MIGB/T2671.2 M5X45 SCREW M5X45 2
81 MITBC431D.01.08.00-3 AIR FILTER 1
82 MITBC431D.01.08.00-2 AIR BOX COVER 1
83 MITBC431D.01.13.01 FUEL CAP ASSY 1
86 MITBC431D.01.13.00-1 FUEL TANK 1
87 MITBC431D.01.13.00-2 FUEL TANK RUBBER 4
88 MITBC431D.01.00.00-10 FUEL TANK BRACKET 1
89 MIGB/T2671.2 M5X25 SCREW M5X25 4
90 MIYD45.03.04-00 BREATHER ASSY 1
91 MITBC431D.01.13.00-6 BREATHER PIPE 1
92 MITBC431D.01.13.00-4 FUEL PIPE 1
93 MITBC431D.01.13.00-5 FUEL PIPE 1
94 MITBC431D.01.13.00-3 GROMME T 1
95 MIYD45.01.01.01-3 CIRCLIP 1
96 MIYD38-3.03.04-00 FUEL FILTER 1
26L/U, 33L/U, 43U, 53U
54
Original Instructions Version June 16
Appliance Parts Drawing: 53U
26L/U, 33L/U, 43U, 53U
55
Original Instructions Version June 16
Appliance Parts List: 53U
ID PART NUMBER DESCRIPTION QTY
1 MITBC431D.02.00-3 CLAMP 3
2 MITBC430D.03.02-00A HARNESS CLAMP 1
3 MIGB/T2671.2 M5X20 SCREW M5X20 1
4 MITBC430D.03.00-2A RETAINER CLIP 1
5 MIGB/T6170 M5 NUT M5 1
6 MITBC431D.03.01-00A OUTER SHAFT ASSEMBLY 1
9 MITBC431D.04.00-00A GEAR BOX ASSEMBLY 1
10 MIGB/T894.1 10 CIRCLIP (SIZE 10) 1
11 MIGB/T893.1 26 E CLIP (SIZE 26) 1
12 MIGB/T276 6000-2Z BALL BEARING 6000-2Z 2
13 MIC43.0116.0002 PINION 1
14 MITBC431D.04.00-1A GEAR BOX 1
15 MIC43.0116.0007 TOP GUARD 1
16 MIGB/T70.1 M5X8 SCREW M5X8 3
17 MIGB/T276 6000-2Z BALL BEARING 6000-2Z 1
18 MIC43.0116.0004 GEAR 1
19 MITBC431D.04.00-3 GEAR SHAFT 1
20 MIGB/T276 6002-2Z BALL BEARING 6002-2Z 1
21 MIGB/T893.1 26 E CLIP (SIZE 26) 1
22 MITBC431D.04.00-6 BLADE CLAMP - LOWER 1
23 MITBC431D.04.00-5 BLADE CLAMP - UPPER 1
24 MITBC431D.04.00-8 NUT PROTECTOR 1
25 MIGB/T6177.2 M10X1.25 FLANGE NUT M10X1.25 1
26 MIGB/T70.1 M6X12 SCREW M6X12 1
27 MIGB/T2671.2 M6X12 SCREW M6X12 1
28 MIGB/T2671.2 M6X25 SCREW M6X25 1
29 MITBC430D.03.00-1 DRIVER SHAFT 1
30 MITBC431D.06.01-1 SKIRT 1
31 MIGB/T845 ST4.8X13 TAPPING SCREW ST4.8X13 2
32 MITBC431D.06.00-2 LINE CUTTER 1
33 MITBC431D.06.02-00 DEBRIS GUARD 1
ID PART NUMBER DESCRIPTION QTY
34 MIC43.1113.0102 SPACER 2
35 MITBC431D.06.00-1A GUARD CLAMP 1
36 MIGB/T2671.2 M6X20 SCREW M6X20 2
37 MITBC431D.05.00-2A RUBBER HANDLE 1
38 MITBC431D.05.00-1A AL TUBING 1
39 MIGB/T2671.2 M5X25 SCREW M5X25 4
40 MITBC431D.05.03-3A UPPER CLAMP 1
41 MITBC431D.05.03-1A MIDDLE CLAMP 1
42 MITBC431D.05.03-2A LOWER CLAMP 1
43 MIGB/T2671.2 M5X25 SCREW M5X25 2
44 MITBC431D.05.01-00A CONTROL HANDLE ASSEMBLY 1
45 MIGB/T2671.2 M5X30 SCREW M5X30 1
46 MIGB/T97.1 M5 WASHER M5 1
47 MITBC431D.05.01-2A THROTTLE HOUSING LH 1
48 MITBC431D.05.01-5 LOCK TRIGGER 1
49 MITBC431D.05.01-7 CONDUIT 1
50 MITBC431D.05.07-00 WIRE CABLE A 1
51 MITBC431D.05.08-00 WIRE CABLE B 1
52 MITBC431D.05.05-00 THROTTLE CABLE ASSEMBLY 1
53 MIGB/T6170 M5 NUT M5 1
54 MIGB/T845 ST3.5X9.5 ST SCREW 3.5X9.5 2
55 MIGB/T845 ST4.2X10 ST SCREW 4.2X10 4
56 MITBC431D.05.01-1A THROTTLE HOUSING RH 1
57 MITBC431D.05.01-4 SPRING - TRIGGER 1
58 MITBC431D.05.01-3 TRIGGER 1
59 MITBC431D.05.01-6 SPRING - TRIGGER 1
60 MIYD38-3.01.11.04-00 ON/OFF SWITCH 1
61 MITBC431D.02.00-2 BLADE COVER 1
62 MITBC430D.02.01-00 NYLON HEAD ASSY 1
63 MIC43.1100.0001 BLADE 1
64 MI00.07.06.0008 HARNESS 1
26L/U, 33L/U, 43U, 53U
56
Original Instructions Version June 16
EC Declaration of Conformity
We Mitox (Rochford Garden Machinery Ltd) - BA9 9RS (importer) declare that the
product(s):
Designation: BRUSHCUTTER
Model(s): 26L SELECT
Type/Serial No: As per rating label on machine
Complies with the following directive(s):
Machinery Directive 2006/42/EC
EMC Directive 2014/30/EU
NRMM Directive 97/68/EC (Amended 2012/46/EU)
Noise Directive 2000/14/EC and 2005/88/EC
The conformity assessment procedure followed was in accordance with:
EN ISO 11806-1:2011
EN ISO 14982
EN ISO 22868
Notified Body:
Intertek Testing Services
Address:
Building No. 86, 1198 Qinzhou Road (North) Shanghai 200233, China
Measured Sound Power Level: 111.2 dB (A)
Guaranteed Sound Power Level: 113 dB (A)
Authorised Signatory and Technical File Holder
Date: 16/05/2016
Signature:
Name: Stewart Anderson
Position: Managing Director
Company: Mitox (Rochford Garden Machinery Ltd)
Address: Wincanton Business Park
Wincanton
Somerset
BA9 9RS
26L/U, 33L/U, 43U, 53U
57
Original Instructions Version June 16
EC Declaration of Conformity
We Mitox (Rochford Garden Machinery Ltd) - BA9 9RS (importer) declare that the
product(s):
Designation: BRUSHCUTTER
Model(s): 26U SELECT
Type/Serial No: As per rating label on machine
Complies with the following directive(s):
Machinery Directive 2006/42/EC
EMC Directive 2014/30/EU
NRMM Directive 97/68/EC (Amended 2012/46/EU)
Noise Directive 2000/14/EC and 2005/88/EC
The conformity assessment procedure followed was in accordance with:
EN ISO 11806-1:2011
EN ISO 14982
EN ISO 22868
Notified Body:
Intertek Testing Services
Address:
Building No. 86, 1198 Qinzhou Road (North) Shanghai 200233, China
Measured Sound Power Level: 111.2 dB (A)
Guaranteed Sound Power Level: 113 dB (A)
Authorised Signatory and Technical File Holder
Date: 16/05/2016
Signature:
Name: Stewart Anderson
Position: Managing Director
Company: Mitox (Rochford Garden Machinery Ltd)
Address: Wincanton Business Park
Wincanton
Somerset
BA9 9RS
26L/U, 33L/U, 43U, 53U
58
Original Instructions Version June 16
EC Declaration of Conformity
We Mitox (Rochford Garden Machinery Ltd) - BA9 9RS (importer) declare that the
product(s):
Designation: BRUSHCUTTER
Model(s): 33L SELECT
Type/Serial No: As per rating label on machine
Complies with the following directive(s):
Machinery Directive 2006/42/EC
EMC Directive 2014/30/EU
NRMM Directive 97/68/EC (Amended 2012/46/EU)
Noise Directive 2000/14/EC and 2005/88/EC
The conformity assessment procedure followed was in accordance with:
EN ISO 11806-1:2011
EN ISO 14982
EN ISO 22868
Notified Body:
Intertek Testing Services
Address:
Building No. 86, 1198 Qinzhou Road (North) Shanghai 200233, China
Measured Sound Power Level: 111.2 dB (A)
Guaranteed Sound Power Level: 113 dB (A)
Authorised Signatory and Technical File Holder
Date: 16/05/2016
Signature:
Name: Stewart Anderson
Position: Managing Director
Company: Mitox (Rochford Garden Machinery Ltd)
Address: Wincanton Business Park
Wincanton
Somerset
BA9 9RS
26L/U, 33L/U, 43U, 53U
59
Original Instructions Version June 16
EC Declaration of Conformity
We Mitox (Rochford Garden Machinery Ltd) - BA9 9RS (importer) declare that the
product(s):
Designation: BRUSHCUTTER
Model(s): 33U SELECT
Type/Serial No: As per rating label on machine
Complies with the following directive(s):
Machinery Directive 2006/42/EC
EMC Directive 2014/30/EU
NRMM Directive 97/68/EC (Amended 2012/46/EU)
Noise Directive 2000/14/EC and 2005/88/EC
The conformity assessment procedure followed was in accordance with:
EN ISO 11806-1:2011
EN ISO 14982
EN ISO 22868
Notified Body:
Intertek Testing Services
Address:
Building No. 86, 1198 Qinzhou Road (North) Shanghai 200233, China
Measured Sound Power Level: 111.2 dB (A)
Guaranteed Sound Power Level: 113 dB (A)
Authorised Signatory and Technical File Holder
Date: 16/05/2016
Signature:
Name: Stewart Anderson
Position: Managing Director
Company: Mitox (Rochford Garden Machinery Ltd)
Address: Wincanton Business Park
Wincanton
Somerset
BA9 9RS
26L/U, 33L/U, 43U, 53U
60
Original Instructions Version June 16
EC Declaration of Conformity
We Mitox (Rochford Garden Machinery Ltd) - BA9 9RS (importer) declare that the
product(s):
Designation: BRUSHCUTTER
Model(s): 43U SELECT
Type/Serial No: As per rating label on machine
Complies with the following directive(s):
Machinery Directive 2006/42/EC
EMC Directive 2014/30/EU
NRMM Directive 97/68/EC (Amended 2012/46/EU)
Noise Directive 2000/14/EC and 2005/88/EC
The conformity assessment procedure followed was in accordance with:
EN ISO 11806-1:2011
EN ISO 14982
EN ISO 22868
Notified Body:
Intertek Testing Services
Address:
Building No. 86, 1198 Qinzhou Road (North) Shanghai 200233, China
Measured Sound Power Level: 111.2 dB (A)
Guaranteed Sound Power Level: 113 dB (A)
Authorised Signatory and Technical File Holder
Date: 16/05/2016
Signature:
Name: Stewart Anderson
Position: Managing Director
Company: Mitox (Rochford Garden Machinery Ltd)
Address: Wincanton Business Park
Wincanton
Somerset
BA9 9RS
26L/U, 33L/U, 43U, 53U
61
Original Instructions Version June 16
EC Declaration of Conformity
We Mitox (Rochford Garden Machinery Ltd) - BA9 9RS (importer) declare that the
product(s):
Designation: BRUSHCUTTER
Model(s): 53U SELECT
Type/Serial No: As per rating label on machine
Complies with the following directive(s):
Machinery Directive 2006/42/EC
EMC Directive 2014/30/EU
NRMM Directive 97/68/EC (Amended 2012/46/EU)
Noise Directive 2000/14/EC and 2005/88/EC
The conformity assessment procedure followed was in accordance with:
EN ISO 11806-1:2011
EN ISO 14982
EN ISO 22868
Notified Body:
Intertek Testing Services
Address:
Building No. 86, 1198 Qinzhou Road (North) Shanghai 200233, China
Measured Sound Power Level: 111.2 dB (A)
Guaranteed Sound Power Level: 113 dB (A)
Authorised Signatory and Technical File Holder
Date: 16/05/2016
Signature:
Name: Stewart Anderson
Position: Managing Director
Company: Mitox (Rochford Garden Machinery Ltd)
Address: Wincanton Business Park
Wincanton
Somerset
BA9 9RS
26L/U, 33L/U, 43U, 53U
62
Original Instructions Version June 16
Notes
26L/U, 33L/U, 43U, 53U
63
Original Instructions Version June 16
Notes
26L/U, 33L/U, 43U, 53U
64
Original Instructions Version June 16
CONDITIONS OF WARRANTY
The manufacturer warrants the product against faulty materials and workmanship for a standard
1 year period and thereafter for the set period specific to each range from the date of purchase.
Warranty does not extend to failure due to fair wear and tear.
SP - 1 Year
SELECT - 3 Years (Subject to yearly servicing)
PREMIUM - 5 Years (Subject to yearly servicing)
PRO - 5 Years Domestic / 3 Years Commercial (Subject to yearly servicing)
(Extended warranty is subject to online registration and yearly servicing)
SP, SELECT and PREMIUM ranges used for commercial purposes have a warranty period of 3
months from the date of purchase.
The manufacturer undertakes to replace any spare parts that are classified as defective by an
appointed Mitox service dealer. The manufacturer will not accept liability for the replacement of
the machine, either partially or wholly, and /or consequential damages and /or interest charges
either directly or indirectly.
Warranty does not cover failure due to:
Insucient maintenance.
Incorrect fuel mixture and stale fuel.
Abnormal use or accidental damage.
Incorrect assembly, adjustment or operation of the product.
Spare parts that are subject to wear e.g. bag, blades, bearings, cables, guards, deflectors,
spark plugs, air filters etc.
Neither does warranty extend to:
Freight and packing costs.
Use of non-genuine spare parts i.e. those from another manufacturer.
Use of the machine for any other purpose than that for which it was designed.
Use and maintenance of the machine in a manner not described in the owner’s manual.
As part of our policy of continuous product improvement, we reserve the right to alter or
amend this specification without notice. As a result, the product may dier from the information
contained herein but any alteration will only be implemented without notice if it is classified as
an improvement to the above specification.
READ THE MANUAL CAREFULLY BEFORE OPERATING THE MACHINE
When ordering spare parts, please quote the part number, this can be found in the parts list
included in this manual.
Retain your proof of purchase, without which no warranty can be oered.
Mitox Garden Machinery, Wincanton Business Park, Wincanton, Somerset, BA9 9RS
Loading...