MITEL PDSP1601ABOAC, PDSP1601MCGGCR Datasheet

PDSP1601/PDSP1601A

ALU and Barrel Shifter

Supersedes version DS3705 - 2.3 September 1996 DS3705 - 3.0 November 1998

The PDSP1601 is a high performance 16-bit arithmetic logic unit with an independent on-chip 16-bit barrel shifter. The PDSP1601A has two operating modes giving 20MHz or 10MHz register-to-register transfer rates.

The PDSP1601 supports Multicycle multiprecision operation. This allows a single device to operate at 20MHz for 16-bit fields, 10MHz for 32-bit fields and 5MHz for 64-bit fields. The PDSP1601 can also be cascaded to produce wider words at the 20MHz rate using the Carry Out and Carry In pins. The Barrel Shifter is also capable of extension, for example the PDSP1601 can used to select a 16-bit field from a 32-bit input in 100ns.

FEATURES

■ 16-bit, 32 instruction 20MHz ALU

■ 16-bit, 20MHz Logical, Arithmetic or Barrel Shifter

■ Independent ALU and Shifter Operation

■ 4 x 16-bit On Chip Scratchpad Registers

■ Multiprecision Operation; e.g. 200ns 64-bit

Accumulate

■ Three Port Structure with Three Internal Feedback

Paths Eliminates I/O Bottlenecks

■ Block Floating Point Support

■ 300mW Maximum Power Dissipation

■ 84-pin Pin Grid Array or 84 Contact LCC Packages

or 100 pin Ceramic Quad Flat Pack

PIN 1A INDEX MARK ON TOP SURFACE

A B C D E

H J K L

1234567891011

AC84

GC100

Fig.1 Pin connections - bottom view

APPLICATIONS

■ Digital Signal Processing

■ Array Processing

■ Graphics

■ Database Addressing

■ High Speed Arithmetic Processors

ASSOCIATED PRODUCTS

PDSP16112 Complex Multiplier PDSP16116 16 x 16 Complex Multiplier PDSP16318 Complex Accumulator PDSP16330 Pythagoras Processor

ORDERING INFORMATION

PDSP1601 MC GGCR 10MHz MIL883 Screened -

QFP package

PDSP1601A BO AC 20MHz Industrial - PGA

package

N.B Further details of the Military grade part are

available in a separate datasheet (DS3763)

PDSP1601/PDSP1601A

PIN DESCRIPTION

AC pin

C6 A6 A5 B5 C5 A4 B4 A3 A2 B3 A1 B2 C2 B1 C1 D2 D1 E3 E2 E1 F1

Function

IA4 MSB MSS

B15 B14 B13 B12 B11 B10

B9 B8 B7 B6 B5 B4 B3 B2 B1 B0

CEB

CLK

AC pin

F3 G3 G1 G2 F1 H1 H2 J1 K1 J2 L1 K2 K3 L2 L3 K4 L4 J5 K5 L5 K6

Function

GND MSA0 MSA1

A15 A14 A13 A12 A11 A10

A9 A8 A7 A6 A5 A4 A3 A2 A1 A0

CEA

MSC

AC pin

J6 J7

L7 K7 L6 L8 K8 L9

L10

L11 K10 J10 K11 J11 H10 H11

F10 G10 G11

Function

IS0 IS1 IS2

IS3 SV0 SV1 SV2 SV3

SVOE

RS0 RS1

VCC

RS2

C0 C1 C2 C3 C4 C5 C6 C7

AC pin

F9 F11 E11 E10

E9 D11 D10 C11 B11 C10 A11 B10

B9 A10

Function

GND

C9 C10 C11 C12 C13 C14 C15

BFP

VCC

CO RA0 RA1 RA2

CI IA0 IA1 IA2 IA3

1 2 3 4 5 6 7 8

9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25

SIG

N/C N/C N/C N/C

VCC

C0 RA0 RA1 RA2

CI IA0 IA1 IA2 IA3 IA4

MSB MSS

B15 B14 B13 B12 B11 B10

B9 B8

26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

SIG

N/C N/C N/C N/C

B7 B6 B5 B4 B3 B2 B1

B0 CEB CLK

GND MSA0 MSA1

A15 A14 A13 A12 A11 A10

A9 A8

51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75

SIG

N/C N/C N/C N/C

A7 A6 A5 A4 A3 A2 A1 A0

CEA

MSC

IS0 IS1 IS2

IS3 SV0 SV1 SV2 SV3

SVOE

RS0 RS1

76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99

100

SIG

N/C N/C N/C N/C

VCC

RS2

C0 C1 C2 C3 C4 C5 C6 C7

GND

C9 C10 C11 C12 C13 C14 C15

BFP

N/C = not connected - leave open circuit All GND and VDD pin must be used

PIN DESCRIPTIONS

PDSP1601/PDSP1601A

Symbol

MSB

MSS

B15 - B0

CEB

CLK

MSA0 - MSA1

A15 - A0

CEA

MSC

IS0 - IS3

SV0 - SV3

Description

ALU B-input multiplexer select control.

This input is latched internally on the rising edge

of CLK. Shifter Input multiplexer select control.1 This input is latched internally on the rising edge

of CLK. B Port data input. Data presented to this port is latched into the input register on the rising

edge of CLK. B15 is the MSB.

Clock enable, B Port input register. When low the clock to this register is enabled. Common clock to all internal registered elements. All registers are loaded, and outputs

change on the rising edge of CLK. ALU A-input multiplexer select control.1 These inputs are latched internally on the rising

edge of CLK. A Port data input. Data presented to this port is latched into the input register on the rising

edge of CLK. A15 is the MSB.

Clock enable, A Port input register. When low the clock to this register is enabled. C-Port multiplexer select control.1 This input is latched internally on the rising edge

of CLK. Instruction inputs to Barrel Shifter, IS3 = MSB.1 These inputs are latched internally on the

rising edge of CLK. Shift Value I/O Port. This port is used as an input when shift values are supplied from

external sources, and as an output when Normalise operations are invoked. The I/O functions are determined by the IS0 - IS3 instruction inputs, and by the

The shift value is latched internally on the rising edge of CLK.

SVOE control.

SVOE

SV Output enable. When high the SV port can only operate as an input. When low the SV port can act as an input or as an output, according to the IS0 - IS3 instruction. This pin should be tied hihg or low, depending upon the application.

RS0, RS1 RS2

C0 - C15

Instruction inputs to Barrel Shifter registers.

rising edge of CLK.

C Port data output. Data output on this port is selected by the C output multiplexer.

These inputs are latched internally on the

C15 is the MSB.

BFP CO RA0 - RA2

Output enable. The C Port outputs are in high impedance condition when this control is high. Block Floating Point Flag from ALU, active high. Carry out from MSB of ALU. Instruction inputs to ALU registers.1 These inputs are latched internally on the rising

edge of CLK. CI IA0 - IA3

IA4 Vcc GND

Carry in to LSB of ALU.

Instruction inputs to ALU.1 IA4 = MSB. These inputs are latched internally on the rising

edge of CLK.

+5V supply: Both Vcc pins must be connected.

0V supply: Both GND pins must be connected.

NOTES

1. All instructions are executed in the cycle commencing with the rising edge of the CLK which latches the inputs.

PDSP1601/PDSP1601A

A INPUT

A REG

A MUX

BFP

LEFT REG. RIGHT REG.

FUNCTIONAL DESCRIPTION

ALU REG FILE

CEA

MSA0-1

ALU

RAD-2

IA0-4

MSB

C MUX

COUT

B MUX

Fig.2 PDSP1601 block diagram

MSC

RS0-2

LEFT REG. RIGHT REG.

B INPUT

B REG

S MUX

BARREL SHIFTER

SHIFTER REG FILE

CEB

MSS

SHIFT

CONTROL

SVOE

IS0-3 SV0-3

The PDSP1601 contains four main blocks: the ALU, the

Barrel Shifter and the two Register Files.

The ALU

The ALU supports 32 instructions as detailed in Table 1.

The inputs to the ALU are selected by the A and B MUXs. Data will fall through from the selected register through the A or B input MUXs and the ALU to the ALU output register file in 50ns for the PDSP1601A (100ns for the PDSP1601).

The ALU instructions are latched, such that the instruction will not start executing until the rising edge of CLK latches the instruction into the device.

The ALU accepts a carry in from the CI input and supplies a carry out to the CO output. Additionally, at the end of each cycle, the carry out from the ALU is loaded into an internal 1 bit register, so that it is available as an input to the ALU on the next cycle. In the manner, multicycle, multiprecision operations are supported. (See MULTICYCLE CASCADE OPERATIONS).

BFP Flag

The ALU has a user programmable BFP flag. This flag may be programmed to become active at any one of four conditions. Two of these conditions are intended to support Block Floating Point operations, in that they provide flags indicating that the ALU result is within a factor of two or four of overflowing the 16 bit number range. For multiprecision operations the flag is only valid whilst the most significant 16 bit byte is being processed. In this manner the BFP flag may be used over any extended word width.

The remaining two conditions detect either an overflow condition or a zero result. For the overflow condition to be

active the ALU result must have overflowed into the 16th (sign) bit, (this flag is only valid whilst the most significant 16 bit byte is being processed). The zero condition is active if the result from the ALU is equal to zero. For multiprecision operations the zero flag must be active for all of the 16 bit bytes of an extended word.

The BFP flag is programmed by executing on of the four SBFXX instructions (see Table 1). During the execution of any of these four instructions, the output of the ALU is forced to zero.

Multicycle/Cascade Operation

The ALU arithmetic instructions contain two or three options for each arithemtic operation.

The ALU is designed to operate with two's complement arithmetic, requiring a one to be added to the LSB for all subtract operations. The instructions set includes instructions that will force a one into the LSB, e.g. MIAX1, AMBX1, BMAX1 (see Table 1).

These instructions are used for the least significant 16 bit byte of any subtract operation.

The user has an option of cascading multiple devices, or multicycling a single device to extend the arithmetic precision. Should the user cascade multiple devices, then the cascade arithmetic instructions using the external CI input should be employed for all but the least significant 16 bit byte, e.g. MIACI, APBCI, BMACI (see Table 1).

Should the user multicycle a single device, then the Multicycle Arithmetic instructions, using the internally registered CO bit should be employed for all but the least significant 16 bit byte, e.g. MIACO, APBCO, AMBCO, BMACO (see Table 1).

Table 1 ALU instructions

Inst

IA4-AI0

Mnemonic

1a. ARITHMETIC INSTRUCTIONS

Operation

Function

PDSP1601/PDSP1601A

Mode

00 01 02 03 04 05 06 07 08 09 0A

0B 0C 0D 0E 0F

00000 00001 00010 00011 00100 00101 00110 00111 01000 01001 01010 01011 01100 01101 01110 01111

CLRXX

MIAX1

MIACI MIACO A2SGN

A2RAL A2RAR A2RSX

APBCI

APBCO

AMBX1

AMBCI

AMBCO

BMAX1

BMACI

BMACO

Inst

10 11 12 13 14 15 16 17

RESET MINUS A MINUS A MINUS A A/2 A/2 A/2 A/2 A PLUS B A PLUS B A MINUS B A MINUS B A MINUS B B MINUS A B MINUS A B MINUS A

1b. LOGICAL INSTRUCTIONS

IA4-AI0

10000 10001 10010 10011 10100 10101 10110 10111

Mnemonic

ANXAB ANANB

ANNAB ORXAB ORNAB XORAB

PASXA

PASNA

CLEAR ALL REGISTERS NA Plus 1 NA Plus CI NA Plus CO A/2 Sign Extend A/2 with RAL LSB A/2 with RAR LSB A/2 with RSX LSB A Plus B Plus CI A Plus B Plus CO A Plus NB Plus 1 A Plus NB Plus CI A Plus NB Plus CO NA Plus B Plus 1 NA Plus B Plus CI NA Plus B Plus CO

Operation

A AND B A AND NB NA AND B A OR B NA OR B A XOR B PASS A INVERT A

Function

A. B A. NB NA. B A + B NA + B A XOR B A NA

---------

LSBYTE

CASCADE

MULTICYCLE

MSBYTE MULTICYCLE MULTICYCLE MULTICYCLE

CASCADE

MULTICYCLE

LSBYTE

CASCADE

MULTICYCLE

LSBYTE

CASCADE

MULTICYCLE

1c. CONTROL INSTRUCTIONS

Inst

18 19 1A

1B 1C 1D

IA4-AI0

11000 11001 11010 11011 11100 11101 11110 11111

Mnemonic

SBFOV

SBFU1 SBFU2 SBFZE

OPONE

OPBYT

OPNIB OPALT

KEY

A = A input to ALU B = B input to ALU CI = External Carry in to ALU CO = Internally Registered Carry out from ALU RAL = ALU Register (Left) RAR = ALU Register (Right) RSX = Shifter Register (Left or Right)

Operation

Set BFP Flag to OVR, Force ALU output to zero Set BFP Flag to UND 1 Force ALU output to zero Set BFP Flag to UND 2 Force ALU output to zero Set BFP Flag to ZERO Force ALU output to zero Output 0001 Hex Output 00FF Hex Output 000F Hex Output 5555 Hex

MNEMONICS

CLRXX Clear All Registers to zero MIAXX Minus A, XX = Carry in to LSB A2XXX A Divided by 2, XXX = Source of MSB APBXX A Plus B, XX = Carry in to LSB AMBXX A Minus B, XX = Carry in to LSB BMAXX B Minus A, XX = Carry in to LSB ANX-Y AND X = Operand 1, Y = Operand 2 ORX-Y OR X = Operand 1, Y = Operand 2 XORXY Exclusive OR X = Operand 1, Y = Operand 2 PASXX Pass XX = Operand SBFXX Set BFP Flag XX = Function OPXXX Output Constant XXX

PDSP1601/PDSP1601A

Divide by Two

The Barrel Shifter

The ALU has four (A2SGN, A2RAL, A2RAR, A2RSX) instructions used for right shifting (dividing by two) extended precision words. These words, (up to 64 bits) may be stored in the two on-chip register files. When the least significant 16 bit word is shifted, the vacant MSB must be filled with the LSB from the next most significant 16 bit byte. This is achieved via the A2RAL, A2RAR or A2RSX instructions which indicate the source of the new MSB (see ALU INSTRUCTION SET).

When the most significant 16 bit byte is right shifted, the MSB must be filled with a duplicate of the original MSB so as to maintain the correct sign (Sign Extension). This operation is achieved via the A2SGN instruction (see Table 1).

Constants

The ALU has four instructions (OPONE, OPBYT, OPNIB, OPALT) that force a constant value onto the ALU output. These values are primarily intended to be used as masks, or the seeds for mask generation, for example, the OPONE instruction will set a single bit in the least significant position. This bit may be rotated any where in the 16 bit field by the Barrel Shifter, allowing the AND function of the ALU to perform bit-pick operations on input data.

CLR

The ALU instruction CLRXX is used as a Master Reset for the entire device. This instruction has the effect of:

The Barrel Shifter supports 16 instructions as detailed in Table 2. The input to the Barrel Shifter is selected by the S MUX. Data will fall through from the selected register, through the S MUX and the Barrel Shifter to the shifter output register file in 50ns for the PDSP1601A (100ns for the PDSP1601).

The Barrel Shifter instructions are latched, such that the instructions will not start executing until the rising edge of CLK latches the instruction into the device.

The Barrel Shifter is capable of Logical Arithmetic or Barrel Shifts in either direction.

A. Logical shifts discard bits that exit the 16 bit field and fill

spaces with zeros.

B. Arithmetic shifts discard bits that exit the 16 bit field and

fill spaces with duplicates of the original MSB.

C. Barrel Shifts rotate the 16 bit fields such that bits tha exit

the 16 bit field to the left or right reappear in the vacant spaces on the right or left.

The amount of shift applied is encoded onto the 4 bit Barrel Shifter input as illustrated in Table 3. The type of shift and the amount are determined by the shift control block. The shift control block (see Fig.3) accepts and decodes the four bit ISO3 instruction. The shift control block contains a priority encoder and two user programmable 4 bit registers R1 and R2.

There are four possible sources of shift value that can be passed onto the Barrel Shifter, there are:

1. Clearing ALU and Barrel Shifter register files to zero.

2. Clearing A and B port input registers to zero.

3. Clearing the R1 and R2 shift control registers to zero.

4. Clearing the internally registered CO bit to zero.

5. Programming the BFP flag to detect

Inst

0 1 2 3 4 5 6 7 8 9 A B C D E F

overflow

IS3-IS0

0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111

conditions.

Mnemonic

LSRSV

LSLSV BSRSV BSLSV LSRR1

LSLR1 LSRR2

LSLR2

LR1SV

LR2SV ASRSV ASRR1 ASRR2

NRMXX NRMR1 NRMR2

Table 2 Barrel shifter instructions

KEY

SV = Shift Value R1 = Register 1 R2 = Register 2 PE = Priority Encoder Output I => SV Port operates as an Input O => SV Port operates as an Output X => SV Port in a High Impedance State

1. The Priority Encoder

2. The SV input

3. The R1 register

4. The R2 register

Operation

Logical Shift Right by SV Logical Shift Left by SV Barrel Shift Right by SV Barrel Shift Left by SV Logical Shift Right by R1 Logical Shift Left by R1 Logical Shift Right by R2 Logical Shift Left by R2 Load Register 1 From SV Load Register 2 From SV Arithmetic Shift Right by SV Arithmetic Shift Right by R1 Arithmetic Shift Right by R2 Normalise Output PE Normalise Output PE, Load R1 Normalise Output PE, Load R2

MNEMONICS

LSXYY Logical Shift, X = Direction YY = Source of Shift Value BSXYY Barrel Shift, X = Direction YY = Source of Shift Value ASXYY Arithmetic Shift, X = Direction YY = Source of Shift Value LXXYY Load XX = Target YY = Source NRMYY Normalise by PE, Output PE value on SV Port, Load YY Reg

I/O

I I I I X X X X I I I X X O O O

+ 11 hidden pages