Chapter One PRODUCT INFORMATION
Chapter One
Printer identification labeling 1-3
Printer Specifications 1-4
Recommended flash cards 1-7
Front and rear views 1-8
Front view (FS-1750/3750) 1-8
Paper feed unit 1-9
Internal assemblies ➊ 1-10
Internal assemblies ➋ 1-11
Safety information 1-12
Laser safety 1-12
Laser notice 1-12
CDRH regulations 1-13
Ozone concentration 1-13
FCC notice 1-13
Important note on the interface connectors 1-15
Canadian Department of Communications compliance statement 1-16
Avis de conformité aux normes du ministère des Communications du Canada 1-16
ISO 7779 1-16
Environmental requirements 1-17
Environmental conditions 1-17
Clearance 1-19
Places to avoid 1-20
Note on power 1-21
CONTENTS 1
About the toner 1-22
Toner container handling 1-22
Toner storage 1-24
Printer identification labeling
The printer bears its model and serial numbers at its back. The following diagrams example labels
for model FS-3750.
The label also contains other safety precautions.
Product information
Printer identification labeling
Europe/Asia version US/Canada version
1-3
FS-1750/FS-3750 Series
Printer Specifications
ENGINE
Specification FS-1750 FS-3750
Product information
Printer Specifications
Print method Electrophotography laser scan
Print speed (A4 or letter, when printing
multiple copies of the same page)
Resolution (dpi) 1200 (Fine 1200 mode/Fast 1200
Smoothing KIR
First print (A4 or letter), depends on
input data
Warm-up time at 23°C or 68°F 50 seconds or less 40 seconds or less
Maximum duty cycle 25,000 pages/month 50,000 pages/month
Laser diode Visible laser
Main charger Scorotron wire
Transferring Biased roller
Separation Carvature separation
Drum cleaning Blade
Drum discharging LED array
Fuser Heat and pressure
Paper Plain paper (See
Capacity of paper feed tray 250 sheets
Capacity of output trays 250 sheets
14 pages/minute 18 pages/minute
mode) 600 (with
KIR) 300 (with
KIR)
15 seconds or less 12 seconds or less
Appendix B
)
ß
ß
ß
ß
ß
ß
ß
ß
ß
ß
ß
ß
ß
1-4
FS-1750/FS-3750 Series
Product information
Printer Specifications
CONTROLLER
Specification FS-1750 FS-3750
CPU PowerPC603e-100 PowerPC603e-166
System ROM size 4MB (16Mb×2) 4MB (16Mb×2)
Resident font ROM size 2MB (16Mb×1) 2MB (16Mb×1)
Main RAM 8MB (2MB×4) 16MB (SIMM)
Additional RAM (SIMM) 72MB maximum 64MB maximum
Memory card SRAM or flash, JEIDA 4.2/PCMCIA 2.1
Recommended flash cards
See
in this chapter.
Host interface Parallel/serial/option(KUIO)
Page description language Prescribe IIe
Standard emulation modes HP LaserJet (PCL6,P5L)
IBM Proprinte X24E, Diablo
630, Epson LQ-850, line printer
WEIGHT AND DIMENSIONS
Specification FS-1750 FS-3750
Width 37.3 cm (14.7”)
Height 31 cm (12.2”)
Depth 38.3 cm (15.1”)
Weight (Main unit) 14 kg (30 lb.)
HP LaserJet (PCL6,P5L)
IBM Proprinter X24E, Diablo
630, Epson LQ-850, line
printer
ß
ß
ß
ß
1-5
FS-1750/FS-3750 Series
Printer Specifications
POWER REQUIRMENTS
Specification FS-1750 FS-3750
Voltage requirements US/Canada 120V AC ±10%, 60Hz ±2%
Europe/Asia 220-240V AC±10%, 50 or 60Hz ±2%
Watts Maximum 667 W 898 W
Printing 311 W 413 W
Standby 118 W 129 W
Sleeping 14 W 16 W
Maximum current US/Canada 5.8 A 7.8 A
Europe 3.0 A 8.0 A
Product information
ENVIRONMENTAL REQUIREMENTS
Specification FS-1750 FS-3750
Operating temperature and humidity
Maximum altitude 2,000 m (6,500 feet)
Noise emission 50 dB maximum/39 dB at standby 53 dB maximum/39 dB at standby
10°C to 32.5°C (50°F to 90.5°F), 20
to 80% RH
ß
ß
1-6
FS-1750/FS-3750 Series
Product information
Printer Specifications
Recommended flash cards
Both FS-1750 and FS-3750 Series printers provide support for a JEIDA/PCMCIA category of
memory card in both SRAM and flash types. The normal series supports memory size of up to 32
MB.
Following is a list of makes and models of flash cards recommended for use with the printers.
Note that the flash card to be used should be operable on 5V
Model Capacity
AMD AmC001CFLKA 1 MB
AmC002CFLKA 2 MB
AmC004CFLKA 4 MB
AmC004DFLKA 4 MB
AmC008DFLKA 8 MB
AmC010CFLKA 10 MB
Fujitsu MB98A81063 1 MB
MB98A81183 2 MB
MB98A81273 4 MB
MB98A81373 8 MB
MB98A81473 16 MB
Panasonic BN-02MHF4C (CC) 2 MB
BN-04MHF4C (CC) 4 MB
Intel Series 2+/iMC004FLSP 4 MB
Centennial FL01M-20-11114-03 1 MB
FL02M-20-11114-03 2 MB
DC
.
1-7
FS-1750/FS-3750 Series
Front and internal views
Front view
Paper exit roller
Product information
Front and internal views
Paper full sensor
(FS-3750 only)
Power switch
Waste
toner/drum
access door
Front operator
panel
Paper feed unit
release lever
Paper cassette
1-8
Size Window
FS-1750/FS-3750 Series
Paper feed unit
Product information
Front and internal views
Size window
Maulti-purpose
tray
Paper feed unit
Paper feed unit
release lever
1-9
Memory card slot
FS-1750/FS-3750 Series
Product information
Front and internal views
Internal assemblies
Developer unit
➊
Laser scanner
assembly
Toner container release lever
Paper exit roller
Upper frame
venti fan
Relay board
KP-504
Cassette paper
size switches
Manual feed
actuator
Enveloper feeder
connector
Drive assembly
Feed roller clutch
1-10
Controller venti
fan
Main motor
Memory card slot
Registration
roller clutch
FS-1750/FS-3750 Series
Product information
Front and internal views
Internal assemblies
Rear paper
jam access
Face-up
paper
Serial interface
connector
Parallel interface
connector
interface slot
(Covered)
➋
High voltage
board
Main charger
terminal
Drum connector
YC821
Drum access slot
Option
Power switch
Face-up stacker
connector
1-11
AC inlet
FS-1750/FS-3750 Series
Product information
Front and internal views
Safety information
Laser safety
This printer is certified as a Class 1 laser product under the U.S. Department of Health and Human
Services (
Safety Act of 1968. This means that the printer does not produce hazardous laser radiation. Since
radiation emitted inside the printer is completely confined within protective housings and external
covers, the laser beam cannot escape from the printer during any phase of user operation.
) Radiation Performance Standard according to Radiation Control for Health and
DHHS
Laser notice
The printer is certified in the U.S. to conform to the requirements of
DHHS
21
Subchapter for
CFR
Class I (1) laser products, and elsewhere is certified as a Class I laser product conforming to the
requirements of
IEC
825.
Class I laser products are not considered to be hazardous. The printer contains internally a Class
IIIb (3b) laser that is nominally a 5 milliwatt laser operating in the wavelength region of 670
nanometers. The laser system and printer are designed so there is never any human access to laser
radiation above a Class I level during normal operation, user maintenance, or prescribed service
condition.
Laser product labels are located on top of the laser scanner:
Laser scanner
1-12
FS-1750/FS-3750 Series
Product information
Front and internal views
Warning - Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation
exposure.
CDRH regulations
The Center of Devices and Radiological Health (
) of the U.S. Food and Drug Administration
CDRH
implemented regulations for laser products on August 2, 1976. These regulations apply to laser
products manufactured after August 1, 1976. Compliance is mandatory for products marketed in
the United States. A label indicating compliance with the
regulations must be attached to
CDRH
laser products marketed in the United States.
Ozone concentration
Laser printers generate ozone gas (O
) which may concentrate in the place of installation and
3
cause an unpleasant smell. To minimize the concentration of ozone gas, we recommend that the
laser printer not be installed in a confined area lacking ventilation.
FCC notice
This device complies with Part 15 of the
Rules. Operation is subject to the following two
FCC
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the
Rules. These limits are designed to provide reasonable protection
FCC
against harmful interference in a residential installation. Th is equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communication. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
1-13
FS-1750/FS-3750 Series
Product information
Front and internal views
Reorient or relocate the receiving antenna.
-
Increase the separation between the equipment and receiver.
-
Connect the equipment into an ou tlet o n a circuit different from that to which the
-
receiver is connected.
Consult the dealer or an experienced radio/
-
technician for help.
TV
Change or modifications not expressly approved by the manufacturer for compliance could void
the user’s authority to operate the equipm en t.
Interference cable to the computer shall be used with shielded circular cable.
Any modification without prior permission may cause harmful interface. If any
modification/change is introduced to this equipment without prior permission, Kyocera, as the
manufacturer, cannot guarantee compliance with
To use equipment which does not comply with
rules.
FCC
rules is prohibited. The printer may be
FCC
optionally installed with the follo wing units:
CONFORMING TO CLASS A LIMITS:
•
-3E Bulk Paper Stacker
HS
-7 Bulk Paper Feeder
•
PF
CONFORMING TO CLASS B LIMITS:
•
-1 Envelope Feeder
EF
-20/DU-21 Duplexer
•
DU
-20/HS-21 Paper Handler/Stacker
•
HS
-20/PF-21 Paper Feeder
•
PF
-20mini/PF-21mini Paper Feeder
•
PF
-6 Sorter/Stacker
•
SO
-20 Bulk Paper Stacker
•
ST
1-14
FS-1750/FS-3750 Series
Product information
Front and internal views
Important note on the interface connectors
Be sure to turn off printer power before connecting or disconnecting an interface cable to the
printer. For protection against static discharge which may be applied to the printer's internal
electronics through the interface connector(s), keep any interface connector which is not in use
capped using the protective cap supplied.
Warning - This equipment has been certified to comply with the limits for a
Class B computing device, pursuant to Subpart J of Part 15 of FCC Rules.
Only peripherals (computer input/output devices, terminals, etc.) certified to
comply with the Class B limits may be attached to this equipment.
Operation with non-certified peripherals is likely to result in interference to
radio and TV reception.
1-15
FS-1750/FS-3750 Series
Product information
Front and internal views
Canadian Department of Communications compliance statement
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulations.
Avis de conformité aux normes du ministère des Communications du
Canada
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel
brouilleur du Canada.
ISO 7779
Maschinenlärminformationsverordnung 3.
beträgt 70 dB(A) oder weniger gemäß
ISO
, 18.01.1991: Der höchste Schalldruckpegel
GSGV
7779.
1-16
FS-1750/FS-3750 Series
Environmental requirements
Environmental conditions
Product information
Environmental requirements
The
ENVIRONMENTAL REQUIREMENTS
optimum operation of the printer. The use of the printer in a location which does not satisfy the
requirements may result in troubles and risk shortening its service life.
The printer will work best if it is installed in a location that is:
Level and well supported (Place the printer on a sturdy table or desk.)
r
Not exposed to sunlight or other bright light (not next to an uncurtained window). Do not
r
place the printer on an unstable cart, stand, or table.
r
Near an
wall outlet, preferably one that can be used for the printer alone (See section
AC
section on page 1-6 should be observed to ensure the
1-17
FS-1750/FS-3750 Series
Product information
Environmental requirements
POWER REQUIRMENTS
on page 1-6). (The outlet should have a ground slot, or an adaptor
should be used. If you use an extension cord, the total length of the power cord plus extension
cord should be 17 feet or 5 meters or less.
Well ventilated, not too hot or cold, an d not too damp or dry (See section
r
REQUIREMENTS
on page 1-6). If you install the printer where the temperature or humidity is
ENVIRONMENTAL
outside the requirements in section Environmental requirements in chapter 1, the best print
quality may not be expected and there will be an increased chance of paper jams.
Provide a sufficient clearances around the printer to ensure ventilation and ease of access. See
r
section
Clearance
on page 1-19.)
1-18
FS-1750/FS-3750 Series
Product information
Environmental requirements
Clearance
Allow the necesary minimum clearance on all sides of the printer (below). A total space of 92 by
138 cm (36 by 54”) is needed.
➎
➊
➋
Clearance Dimensions
➊
Left
Front
Right
Back
Above
➋
➌
➍
➎
30 cm (12”)
60 cm (24”)
25 cm (10”)
40 cm (16”) or 20 cm (8”) if the face-up tray is not
installed.
30 cm (12”)
➍
➌
1-19
FS-1750/FS-3750 Series
Environmental requirements
Places to avoid
Avoid installing the printer in locations exposed to:
• Direct drafts of hot or cold air.
• Direct drafts of outside air. (Avoid locations next to outside doors.)
Product information
• Sudden temperature or humidity changes.
• Any source of high heat, such as a radiator or stove.
• Excessive dust. Dust and smoke may cause contamination on the laser scanner window,
causing print quality problem.
• Vibration.
• Ammonia fumes or other harmful fumes. (In case of humigating the room or saturate it with
insecticide, remove the printer first.)
• Avoid greenhouse-like rooms. (Because of sunlight and humidity.)
• Avoid enclosed spaces that block v e ntilation.
• Avoid sites more than 6500 feet or 2000 meters above sea level.
1-20
FS-1750/FS-3750 Series
Product information
Environmental requirements
Note on power
• Use only the power source voltage conforming to the printer’s rated power voltage (See the
POWER REQUIMENTS
• Disconnect the printer from the power source before attempting removal or re-placement of an
electrical component or a printed-circuit board.
on page 1-6). Do not use other power sources.
• The printer should not be connected to a power source until the instruction is given to do so
when performing tests described in this manual.
• In connecting the printer power, exercise an extreme care in handling the power supply or any
other electric parts which may give an electric shock.
• Before performing maintenance or repair, power from both the power source and the
associated peripheral devices (computer, sorter, etc.) should be disconnected, unless otherwise
specified.
• To avoid possible electrical shock, extreme caution must be exercised in handling the power
cord and any other electrical part.
1-21
FS-1750/FS-3750 Series
Product information
Environmental requirements
Warning!
Warning! /Wornung!
Warning!Warning!
As the disconnect device is not incorporated in the printer's AC primary circuit, an easily
accessible socket outlet must be provided near the equipment.
If the printer is used with the optional Sorter (SO-6) or Stacker (ST-20), in order to avoid shortcircuiting, it should be ensured that these devices are plugged securely into their respective power
outlets.
Da kein Trennschalter in den Wechselstrom-Primärkreis des Druckers eingebaut ist, muß eine
leicht zugängliche Steckdose in der Nähe des Gerätes vorhanden sein.
Wenn der Drucker mit dem gesonderten Sorter (SO-6) oder Stapler (ST-20) verwendet wird, muß
darauf geachtet werden, daß diese Geräte einwandfrei an separate Steckdosen angeschlossen sind,
um Kurzschluß zu vermeiden.
About the toner
The printer should use Kyocera TK-20/TK-20H Toner Kit. To ensure the high prin t q uality and
long service life, the following handling precautions should apply.
Caution - As the Ecosys printers are designed to ensure the optimum print
quality when used with the Kyocera’s proprietary toner, Kyocera do not
recommend to use any refilled toner containers that may be available
commercially. This is because Kyocera have no means for control over how
such refilled toner could affect the print quality and the reliability of the
printer.
Toner container handling
To loosen and mix the toner inside, with the label side down, thoroughly shake the toner container
(in the direction of the arrow) ten times or more.
1-22
FS-1750/FS-3750 Series
Product information
Environmental requirements
Do not attempt to disassemble or refill the toner container.
1-23
FS-1750/FS-3750 Series
Product information
Environmental requirements
Toner storage
The toner contained in the container is susceptible to temperature and humidity. To ensure the
high print quality, store the toner container in a place that satisfy the following environmental
conditions:
Note.
Temperature -20°C to 40°C (-4°F to 104°F)
Humidity 15 to 90% RH
If the toner container is removed from the printer’s developer unit, put it in a protective bag and
keep it in a dark place.
Caution -
Caution - If the printer is shipped for return, etc., do not ship it with the
Caution - Caution toner container installed. Otherwise, toner may leak and contamination may
result in the printer.
1-24
FS-1750/FS-3750 Series
Product information
Environmental requirements
1-25
FS-1750/FS-3750 Series
Loading...