SAFETY DATA SHEET
A00810 MST DUST MOP TREATMENT 20net18
Version 1.0
Revision Date 02/17/2015
Print Date 06/01/2015
Material name
:
A00810 MST DUST MOP TREATMENT 20net18
Material number
:
000000000001003402
Company
:
Zep Inc.
Address
:
1310 Seaboard Industrial Blvd., NW
Atlanta, GA 30318
Telephone
:
404-352-1680
Emergency telephone numbers
For SDS Information
:
Compliance Services 1-877-428-9937
For a Medical Emergency
:
877-541-2016 Toll Free - All Calls Recorded
For a Transportation
Emergency
:
CHEMTREC: 800-424-9300 - All Calls Recorded.
In the District of Columbia 202-483-7616
Appearance
Aerosol containing a liquefied gas
Colour
white
Odour
characteristic
Flammable aerosols
:
Category 2
Gases under pressure
:
Liquefied gas
Skin irritation
:
Category 2
Hazard pictograms
:
Signal word
:
Warning
Hazard statements
:
H223 Flammable aerosol.
H280 Contains gas under pressure; may explode if heated.
H315 Causes skin irritation.
Precautionary statements
:
Prevention:
P210 Keep away from heat, hot surfaces, sparks, open flames
and other ignition sources. No smoking.
P211 Do not spray on an open flame or other ignition source.
P251 Pressurized container: Do not pierce or burn, even after
use.
P264 Wash skin thoroughly after handling.
SECTION 1. PRODUCT AND COMPANY IDENTIFICATION
Manufacturer or supplier's details
SECTION 2. HAZARDS IDENTIFICATION
Emergency Overview
GHS Classification
GHS Label element
1 / 11
SAFETY DATA SHEET
A00810 MST DUST MOP TREATMENT 20net18
Version 1.0
Revision Date 02/17/2015
Print Date 06/01/2015
P280 Wear protective gloves.
Response:
P302 + P352 IF ON SKIN: Wash with plenty of soap and water.
P332 + P313 If skin irritation occurs: Get medical advice/
attention.
P362 Take off contaminated clothing and wash before reuse.
Storage:
P410 + P412 Protect from sunlight. Do not expose to
temperatures exceeding 50 °C/ 122 °F.
IARC
No component of this product present at levels greater than or
equal to 0.1% is identified as probable, possible or confirmed
human carcinogen by IARC.
ACGIH
No component of this product present at levels greater than or
equal to 0.1% is identified as a carcinogen or potential
carcinogen by ACGIH.
OSHA
No component of this product present at levels greater than or
equal to 0.1% is identified as a carcinogen or potential
carcinogen by OSHA.
NTP
No component of this product present at levels greater than or
equal to 0.1% is identified as a known or anticipated carcinogen
by NTP.
Chemical Name
CAS-No.
Concentration [%]
Distillates (petroleum), hydrotreated heavy
naphthenic
64742-52-5
>= 10 - < 20
Distillates (petroleum), hydrotreated light (Vapour
and gas)
64742-47-8
>= 5 - < 10
butane
106-97-8
>= 5 - < 10
Stoddard solvent
8052-41-3
>= 5 - < 10
propane
74-98-6
>= 1 - < 5
General advice
:
Show this safety data sheet to the doctor in attendance.
Do not leave the victim unattended.
If inhaled
:
If unconscious place in recovery position and seek medical
advice.
If symptoms persist, call a physician.
In case of skin contact
:
If skin irritation persists, call a physician.
Wash off immediately with plenty of water for at least 15
minutes.
If on clothes, remove clothes.
Potential Health Effects
Carcinogenicity:
SECTION 3. COMPOSITION/INFORMATION ON INGREDIENTS
Hazardous components
SECTION 4. FIRST AID MEASURES
2 / 11
SAFETY DATA SHEET
A00810 MST DUST MOP TREATMENT 20net18
Version 1.0
Revision Date 02/17/2015
Print Date 06/01/2015
In case of eye contact
:
Remove contact lenses.
Flush eyes with water at least 15 minutes. Get medical
attention if eye irritation develops or persists.
If swallowed
:
Keep respiratory tract clear.
DO NOT induce vomiting unless directed to do so by a
physician or poison control center.
Suitable extinguishing media
:
Alcohol-resistant foam
Carbon dioxide (CO2)
Dry chemical
Water spray jet
Unsuitable extinguishing
media
:
High volume water jet
Specific hazards during
firefighting
:
Do not allow run-off from fire fighting to enter drains or water
courses.
Hazardous combustion
products
:
Carbon dioxide (CO2)
Carbon monoxide
Smoke
Specific extinguishing
methods
:
Use extinguishing measures that are appropriate to local
circumstances and the surrounding environment.
Further information
:
Collect contaminated fire extinguishing water separately. This
must not be discharged into drains.
Fire residues and contaminated fire extinguishing water must
be disposed of in accordance with local regulations.
For safety reasons in case of fire, cans should be stored
separately in closed containments.
Use a water spray to cool fully closed containers.
Special protective equipment
for firefighters
:
Wear self-contained breathing apparatus for firefighting if
necessary.
Personal precautions,
protective equipment and
emergency procedures
:
Use personal protective equipment.
Ensure adequate ventilation.
Remove all sources of ignition.
Evacuate personnel to safe areas.
Beware of vapours accumulating to form explosive
concentrations. Vapours can accumulate in low areas.
Environmental precautions
:
Prevent product from entering drains.
Prevent further leakage or spillage if safe to do so.
If the product contaminates rivers and lakes or drains inform
respective authorities.
Methods and materials for
:
Soak up with inert absorbent material (e.g. sand, silica gel,
SECTION 5. FIREFIGHTING MEASURES
SECTION 6. ACCIDENTAL RELEASE MEASURES
3 / 11
SAFETY DATA SHEET
A00810 MST DUST MOP TREATMENT 20net18
Version 1.0
Revision Date 02/17/2015
Print Date 06/01/2015
containment and cleaning up
acid binder, universal binder, sawdust).
Sweep up or vacuum up spillage and collect in suitable
container for disposal.
Advice on safe handling
:
Avoid contact with skin and eyes.
For personal protection see section 8.
Smoking, eating and drinking should be prohibited in the
application area.
Take precautionary measures against static discharges.
Provide sufficient air exchange and/or exhaust in work rooms.
Open drum carefully as content may be under pressure.
Always replace cap after use.
Dispose of rinse water in accordance with local and national
regulations.
Do not breathe vapours or spray mist.
Conditions for safe storage
:
BEWARE: Aerosol is pressurized. Keep away from direct sun
exposure and temperatures over 50 °C. Do not open by force
or throw into fire even after use. Do not spray on flames or
red-hot objects.
No smoking.
Containers which are opened must be carefully resealed and
kept upright to prevent leakage.
Observe label precautions.
Electrical installations / working materials must comply with
the technological safety standards.
Keep in a dry, cool and well-ventilated place.
Materials to avoid
:
Strong oxidizing agents
Components
CAS-No.
Value type
(Form of
exposure)
Control
parameters /
Permissible
concentration
Basis
Distillates (petroleum),
hydrotreated heavy naphthenic
64742-52-5
TWA (Mist)
5 mg/m3
OSHA Z-1
TWA
(Inhalable
fraction)
5 mg/m3
ACGIH
Distillates (petroleum),
hydrotreated light (Vapour and
gas)
64742-47-8
TWA
500 ppm
2,000 mg/m3
OSHA Z-1
TWA
400 ppm
1,600 mg/m3
OSHA P0
butane
106-97-8
TWA
800 ppm
1,900 mg/m3
NIOSH REL
TWA
800 ppm
OSHA P0
SECTION 7. HANDLING AND STORAGE
SECTION 8. EXPOSURE CONTROLS/PERSONAL PROTECTION
Components with workplace control parameters
4 / 11
SAFETY DATA SHEET
A00810 MST DUST MOP TREATMENT 20net18
Version 1.0
Revision Date 02/17/2015
Print Date 06/01/2015
1,900 mg/m3
Stoddard solvent
8052-41-3
TWA
100 ppm
ACGIH
TWA
350 mg/m3
NIOSH REL
C
1,800 mg/m3
NIOSH REL
TWA
500 ppm
2,900 mg/m3
OSHA Z-1
TWA
100 ppm
525 mg/m3
OSHA P0
propane
74-98-6
TWA
1,000 ppm
ACGIH
TWA
1,000 ppm
1,800 mg/m3
NIOSH REL
TWA
1,000 ppm
1,800 mg/m3
OSHA Z-1
TWA
1,000 ppm
1,800 mg/m3
OSHA P0
Respiratory protection
:
In case of insufficient ventilation, wear suitable respiratory
equipment.
Remarks
:
The suitability for a specific workplace should be discussed
with the producers of the protective gloves.
Eye protection
:
Safety glasses
Ensure that eyewash stations and safety showers are close to
the workstation location.
Skin and body protection
:
impervious clothing
Choose body protection according to the amount and
concentration of the dangerous substance at the work place.
Hygiene measures
:
When using do not eat or drink.
When using do not smoke.
Wash hands before breaks and at the end of workday.
Appearance
:
Aerosol containing a liquefied gas
Colour
:
white
Odour
:
characteristic
Odour Threshold
:
no data available
pH : not applicable
Melting point/freezing point
:
no data available
Boiling point
:
no data available
Flash point
:
not applicable
Evaporation rate
:
no data available
Personal protective equipment
Hand protection
SECTION 9. PHYSICAL AND CHEMICAL PROPERTIES
5 / 11
SAFETY DATA SHEET
A00810 MST DUST MOP TREATMENT 20net18
Version 1.0
Revision Date 02/17/2015
Print Date 06/01/2015
Upper explosion limit
:
no data available
Lower explosion limit
:
no data available
Vapour pressure
:
no data available
Relative vapour density
:
no data available
Density
:
0.93 g/cm3
Water solubility
:
emulsifiable
Partition coefficient: noctanol/water
:
no data available
Auto-ignition temperature
:
not determined
Thermal decomposition
:
no data available
Viscosity, kinematic
:
no data available
Reactivity
:
Stable
Chemical stability
:
Stable under normal conditions.
Possibility of hazardous
reactions
:
No decomposition if stored and applied as directed.
Vapours may form explosive mixture with air.
Conditions to avoid
:
Heat, flames and sparks.
Extremes of temperature and direct sunlight.
Incompatible materials
:
Oxidizing agents
Hazardous decomposition
products
:
Carbon dioxide (CO2)
Carbon monoxide
Remarks: May cause skin irritation in susceptible persons.
Solubility(ies)
Viscosity
SECTION 10. STABILITY AND REACTIVITY
SECTION 11. TOXICOLOGICAL INFORMATION
Acute toxicity
no data available
Skin corrosion/irritation
Product:
Serious eye damage/eye irritation
Product:
6 / 11
SAFETY DATA SHEET
A00810 MST DUST MOP TREATMENT 20net18
Version 1.0
Revision Date 02/17/2015
Print Date 06/01/2015
Remarks: Vapours may cause irritation to the eyes, respiratory system and the skin.
Remarks: no data available
Remarks: no data available
Partition coefficient: noctanol/water
:
Remarks: no data available
Respiratory or skin sensitisation
no data available
Germ cell mutagenicity
no data available
Carcinogenicity
no data available
Reproductive toxicity
no data available
Distillates (petroleum), hydrotreated heavy naphthenic:
Distillates (petroleum), hydrotreated light (Vapour and gas):
butane:
Stoddard solvent:
propane:
STOT - single exposure
no data available
STOT - repeated exposure
no data available
Aspiration toxicity
no data available
Further information
Product:
Components:
Distillates (petroleum), hydrotreated light (Vapour and gas):
SECTION 12. ECOLOGICAL INFORMATION
Ecotoxicity
no data available
Persistence and degradability
no data available
Bioaccumulative potential
Product:
7 / 11
SAFETY DATA SHEET
A00810 MST DUST MOP TREATMENT 20net18
Version 1.0
Revision Date 02/17/2015
Print Date 06/01/2015
Partition coefficient: noctanol/water
:
Pow: 2.89
Regulation
40 CFR Protection of Environment; Part 82 Protection of
Stratospheric Ozone - CAA Section 602 Class I
Substances
Remarks
This product neither contains, nor was manufactured
with a Class I or Class II ODS as defined by the U.S.
Clean Air Act Section 602 (40 CFR 82, Subpt. A, App.A
+ B).
Additional ecological
information
:
An environmental hazard cannot be excluded in the
event of unprofessional handling or disposal., Harmful to
aquatic life with long lasting effects.
Additional ecological
information
:
no data available
Waste from residues
:
Dispose of in accordance with local regulations.
The product should not be allowed to enter drains, water
courses or the soil.
Do not contaminate ponds, waterways or ditches with
chemical or used container.
Contaminated packaging
:
Empty remaining contents.
Dispose of as unused product.
Do not re-use empty containers.
Do not burn, or use a cutting torch on, the empty drum.
Transportation Regulation: 49 CFR (USA):
ORM-D, CONSUMER COMMODITY
Transportation Regulation: IMDG (Vessel):
UN1950, AEROSOLS, 2.1, - Limited quantity
Components:
butane :
Mobility in soil
no data available
Other adverse effects
no data available
Product:
Components:
Distillates (petroleum), hydrotreated light (Vapour and gas) :
SECTION 13. DISPOSAL CONSIDERATIONS
Disposal methods
SECTION 14. TRANSPORT INFORMATION
8 / 11
SAFETY DATA SHEET
A00810 MST DUST MOP TREATMENT 20net18
Version 1.0
Revision Date 02/17/2015
Print Date 06/01/2015
Transportation Regulation: IATA (Cargo Air):
UN1950, Aerosols, flammable, 2.1, - Limited quantity
Transportation Regulation: IATA (Passenger Air):
UN1950, Aerosols, flammable, 2.1, - Limited quantity
Transportation Regulation: TDG (Canada):
UN1950, AEROSOLS, 2.1, - Limited quantity
Components
CAS-No.
Component RQ
(lbs)
Calculated product RQ
(lbs)
xylenes
1330-20-7
100
*
SARA 311/312 Hazards
:
Fire Hazard
Sudden Release of Pressure Hazard
Acute Health Hazard
SARA 302
:
SARA 302: No chemicals in this material are subject to the
reporting requirements of SARA Title III, Section 302.
SARA 313
:
SARA 313: This material does not contain any chemical
components with known CAS numbers that exceed the
threshold (De Minimis) reporting levels established by SARA
Title III, Section 313.
California Prop 65
This product does not contain any chemicals known to State of
California to cause cancer, birth defects, or any other
reproductive harm.
TSCA
On TSCA Inventory
DSL
This product contains one or several components that are not on the
Canadian DSL nor NDSL.
AICS
Not in compliance with the inventory
NZIoC
Not in compliance with the inventory
PICCS
Not in compliance with the inventory
IECSC
Not in compliance with the inventory
SECTION 15. REGULATORY INFORMATION
EPCRA - Emergency Planning and Community Right-to-Know Act
CERCLA Reportable Quantity
*: Calculated RQ exceeds reasonably attainable upper limit.
SARA 304 Extremely Hazardous Substances Reportable Quantity
This material does not contain any components with a section 304 EHS RQ.
The components of this product are reported in the following inventories:
Inventory Acronym and Validity Area Legend:
9 / 11
SAFETY DATA SHEET
A00810 MST DUST MOP TREATMENT 20net18
Version 1.0
Revision Date 02/17/2015
Print Date 06/01/2015
NFPA:
HMIS III:
Hazard pictograms
:
Signal word
:
Warning:
Hazard statements
:
Flammable aerosol. Contains gas under pressure; may explode if heated. Causes skin
irritation.
Precautionary statements
:
Prevention: Keep away from heat, hot surfaces, sparks, open flames and other ignition
sources. No smoking. Do not spray on an open flame or other ignition source.
Pressurized container: Do not pierce or burn, even after use. Wash skin thoroughly
after handling. Wear protective gloves.
Response: IF ON SKIN: Wash with plenty of soap and water. If skin irritation occurs:
Get medical advice/ attention. Take off contaminated clothing and wash before reuse.
Storage: Protect from sunlight. Do not expose to temperatures exceeding 50 °C/ 122
°F.
Flammability
Health
Instability
3
3
0
Special hazard.
FLAMMABILITY
PHYSICAL HAZARD
HEALTH
3
2
3
0 = not significant, 1 =Slight,
2 = Moderate, 3 = High
4 = Extreme, * = Chronic
AICS (Australia), DSL (Canada), IECSC (China), REACH (European Union), ENCS (Japan), ISHL
(Japan), KECI (Korea), NZIoC (New Zealand), PICCS (Philippines), TSCA (USA)
SECTION 16. OTHER INFORMATION
Further information
OSHA GHS Label Information:
We believe the statements, technical information and recommendations contained herein are
reliable, but they are given without warranty or guarantee of any kind. The information in this
document applies to this specific material as supplied. It may not be valid for this material if it
is used in combination with any other materials. Users should make their own investigations
to determine the suitability and applicability of the information for their particular purposes.
This SDS has been prepared by the Compliance Services organization supporting this
manufacturer, supplier or distributor.
Zep Inc. markets products under well recognized and established brand names such as Zep®,
Zep Commercial®,Zep Professional®, Enforcer®, National Chemical™, Selig™, Misty®, Next
Dimension™, Petro®, i-Chem®, TimeMist®, TimeWick™, MicrobeMax®, Country Vet®,
Konk®, Original Bike Spirits®, Blue Coral®, Black Magic®, Rain-X®, Niagara National™, FC
Forward Chemicals®,Rexodan®, Mykal™, and a number of private labeled brands.
10 / 11
SAFETY DATA SHEET
A00810 MST DUST MOP TREATMENT 20net18
Version 1.0
Revision Date 02/17/2015
Print Date 06/01/2015
11 / 11
Loading...