A00141 MST STAINLESS STL CLNR/PLSH 20N15
Material number
:
000000000001001541
Company
:
Zep Inc.
Address
:
1310 Seaboard Industrial Blvd., NW
Atlanta, GA 30318
Telephone
:
404-352-1680
Emergency telephone numbers
For SDS Information
:
Compliance Services 1-877-428-9937
For a Medical Emergency
:
877-541-2016 Toll Free - All Calls Recorded
For a Transportation
Emergency
:
CHEMTREC: 800-424-9300 - All Calls Recorded.
In the District of Columbia 202-483-7616
Recommended use
:
Cleaner
Appearance
Aerosol containing a liquefied gas
Colour
clear
Odour
characteristic
Flammable aerosols
:
Category 1
Gases under pressure
:
Liquefied gas
Skin sensitisation
:
Category 1
Hazard pictograms
:
Signal word
:
Danger
Hazard statements
:
H222 Extremely flammable aerosol.
H280 Contains gas under pressure; may explode if heated.
H317 May cause an allergic skin reaction.
Precautionary statements
:
Prevention:
P210 Keep away from heat/sparks/open flames/hot surfaces.
No smoking.
P211 Do not spray on an open flame or other ignition source.
P251 Pressurized container: Do not pierce or burn, even after
SECTION 1. PRODUCT AND COMPANY IDENTIFICATION
Manufacturer or supplier's details
Recommended use of the chemical and restrictions on use
SECTION 2. HAZARDS IDENTIFICATION
Emergency Overview
GHS Classification
GHS label elements
1 / 12
Page 2
SAFETY DATA SHEET
A00141 MST STAINLESS STL CLNR/PLSH 20N15
Version 1.4
Revision Date 02/25/2017
Print Date 05/05/2017
use.
P261 Avoid breathing dust/ fume/ gas/ mist/ vapours/ spray.
P272 Contaminated work clothing should not be allowed out of
the workplace.
P280 Wear protective gloves.
Response:
P302 + P352 IF ON SKIN: Wash with plenty of soap and water.
P333 + P313 If skin irritation or rash occurs: Get medical
advice/ attention.
P363 Wash contaminated clothing before reuse.
Storage:
P410 + P412 Protect from sunlight. Do not expose to
temperatures exceeding 50 °C/ 122 °F.
Disposal:
Dispose of contents/container in accordance with local
regulation.
Substance / Mixture
:
Mixture
Chemical name
CAS-No.
Concentration [%]
Distillates (petroleum), hydrotreated heavy
naphthenic
Move out of dangerous area.
Show this safety data sheet to the doctor in attendance.
Do not leave the victim unattended.
If inhaled
:
If unconscious place in recovery position and seek medical
advice.
If symptoms persist, call a physician.
In case of skin contact
:
If skin irritation persists, call a physician.
Wash off immediately with plenty of water for at least 15
minutes.
If on clothes, remove clothes.
In case of eye contact
:
Remove contact lenses.
Protect unharmed eye.
Keep eye wide open while rinsing.
If eye irritation persists, consult a specialist.
If in eyes, rinse with water for 15 minutes.
If swallowed
:
Keep respiratory tract clear.
Never give anything by mouth to an unconscious person.
SECTION 3. COMPOSITION/INFORMATION ON INGREDIENTS
Hazardous components
The exact percentages of disclosed substances are withheld as trade secrets.
SECTION 4. FIRST AID MEASURES
2 / 12
Page 3
SAFETY DATA SHEET
A00141 MST STAINLESS STL CLNR/PLSH 20N15
Version 1.4
Revision Date 02/25/2017
Print Date 05/05/2017
If symptoms persist, call a physician.
DO NOT induce vomiting unless directed to do so by a
physician or poison control center.
Most important symptoms
and effects, both acute and
delayed
:
Effects are immediate and delayed.
Symptoms may include irritation, redness, pain, and rash.
Effects are dependent on exposure (dose, concentration,
contact time).
Causes skin irritation.
May cause an allergic skin reaction.
Review section 2 of SDS to see all potential hazards.
Notes to physician
:
Treat symptomatically. Symptoms may be delayed.
Suitable extinguishing media
:
Alcohol-resistant foam
Carbon dioxide (CO2)
Dry chemical
Water spray jet
Unsuitable extinguishing
media
:
High volume water jet
Hazardous combustion
products
:
Carbon dioxide (CO2)
Carbon monoxide
Smoke
Specific extinguishing
methods
:
Use extinguishing measures that are appropriate to local
circumstances and the surrounding environment.
Further information
:
For safety reasons in case of fire, cans should be stored
separately in closed containments.
Use a water spray to cool fully closed containers.
Special protective equipment
for firefighters
:
Wear self-contained breathing apparatus for firefighting if
necessary.
Personal precautions,
protective equipment and
emergency procedures
:
Use personal protective equipment.
Ensure adequate ventilation.
Remove all sources of ignition.
Evacuate personnel to safe areas.
Beware of vapours accumulating to form explosive
concentrations. Vapours can accumulate in low areas.
Environmental precautions
:
Prevent product from entering drains.
Prevent further leakage or spillage if safe to do so.
If the product contaminates rivers and lakes or drains inform
respective authorities.
Methods and materials for
containment and cleaning up
:
Soak up with inert absorbent material (e.g. sand, silica gel,
acid binder, universal binder, sawdust).
Sweep up or vacuum up spillage and collect in suitable
SECTION 5. FIREFIGHTING MEASURES
SECTION 6. ACCIDENTAL RELEASE MEASURES
3 / 12
Page 4
SAFETY DATA SHEET
A00141 MST STAINLESS STL CLNR/PLSH 20N15
Version 1.4
Revision Date 02/25/2017
Print Date 05/05/2017
container for disposal.
Advice on safe handling
:
Avoid exposure - obtain special instructions before use.
Avoid contact with skin and eyes.
For personal protection see section 8.
Smoking, eating and drinking should be prohibited in the
application area.
Take precautionary measures against static discharges.
Provide sufficient air exchange and/or exhaust in work rooms.
Open drum carefully as content may be under pressure.
Dispose of rinse water in accordance with local and national
regulations.
Persons susceptible to skin sensitisation problems or asthma,
allergies, chronic or recurrent respiratory disease should not
be employed in any process in which this mixture is being
used.
Always replace cap after use.
Do not breathe vapours or spray mist.
Conditions for safe storage
:
BEWARE: Aerosol is pressurized. Keep away from direct sun
exposure and temperatures over 50 °C. Do not open by force
or throw into fire even after use. Do not spray on flames or
red-hot objects.
No smoking.
Keep in a dry, cool and well-ventilated place.
Observe label precautions.
Electrical installations / working materials must comply with
the technological safety standards.
Materials to avoid
:
Strong oxidizing agents
Components
CAS-No.
Value type
(Form of
exposure)
Control
parameters /
Permissible
concentration
Basis
Distillates (petroleum),
hydrotreated heavy naphthenic
64742-52-5
TWA (Mist)
5 mg/m3
OSHA Z-1
TWA
(Inhalable
fraction)
5 mg/m3
ACGIH
Distillates (petroleum),
hydrotreated light
64742-47-8
TWA
500 ppm
2,000 mg/m3
OSHA Z-1
TWA
400 ppm
1,600 mg/m3
OSHA P0
TWA (Mist)
5 mg/m3
OSHA Z-1
TWA (Mist)
5 mg/m3
OSHA P0
TWA (Mist)
5 mg/m3
NIOSH REL
SECTION 7. HANDLING AND STORAGE
SECTION 8. EXPOSURE CONTROLS/PERSONAL PROTECTION
Components with workplace control parameters
4 / 12
Page 5
SAFETY DATA SHEET
A00141 MST STAINLESS STL CLNR/PLSH 20N15
Version 1.4
Revision Date 02/25/2017
Print Date 05/05/2017
ST (Mist)
10 mg/m3
NIOSH REL
PEL
(particulate)
5 mg/m3
CAL PEL
propane
74-98-6
TWA
1,000 ppm
ACGIH
TWA
1,000 ppm
1,800 mg/m3
NIOSH REL
TWA
1,000 ppm
1,800 mg/m3
OSHA Z-1
TWA
1,000 ppm
1,800 mg/m3
OSHA P0
PEL
1,000 ppm
1,800 mg/m3
CAL PEL
butane
106-97-8
TWA
800 ppm
1,900 mg/m3
NIOSH REL
TWA
800 ppm
1,900 mg/m3
OSHA P0
PEL
800 ppm
1,900 mg/m3
CAL PEL
citral
5392-40-5
TWA
(Inhalable
fraction and
vapor)
5 ppm
ACGIH
Engineering measures
:
effective ventilation in all processing areas
Respiratory protection
:
Use respiratory protection unless adequate local exhaust
ventilation is provided or exposure assessment demonstrates
that exposures are within recommended exposure guidelines.
Material
:
Protective gloves
Remarks
:
The suitability for a specific workplace should be discussed
with the producers of the protective gloves.
Eye protection
:
Safety glasses
Ensure that eyewash stations and safety showers are close to
the workstation location.
Skin and body protection
:
Impervious clothing
Choose body protection according to the amount and
concentration of the dangerous substance at the work place.
Hygiene measures
:
When using do not eat or drink.
When using do not smoke.
Wash hands before breaks and at the end of workday.
Appearance
:
Aerosol containing a liquefied gas
Colour
:
clear
Personal protective equipment
Hand protection
SECTION 9. PHYSICAL AND CHEMICAL PROPERTIES
5 / 12
Page 6
SAFETY DATA SHEET
A00141 MST STAINLESS STL CLNR/PLSH 20N15
Version 1.4
Revision Date 02/25/2017
Print Date 05/05/2017
Odour
:
characteristic
Odour Threshold
:
No data available
pH : Not applicable
Melting point/freezing point
:
Not applicable
Boiling point
:
Not applicable
Flash point
:
Not applicable
Evaporation rate
:
No data available
Flammability (solid, gas)
:
Extremely flammable aerosol.
Upper explosion limit
:
No data available
Lower explosion limit
:
No data available
Vapour pressure
:
4,136 hPa (21 °C)
Relative vapour density
:
No data available
Density
:
0.856 g/cm3
Water solubility
:
insoluble
Partition coefficient: noctanol/water
:
No data available
Auto-ignition temperature
:
not determined
Thermal decomposition
:
No data available
Viscosity, kinematic
:
No data available
Heat of combustion
:
46.27 kJ/g
Reactivity
:
Stable
Chemical stability
:
Stable under normal conditions.
Possibility of hazardous
reactions
:
Vapours may form explosive mixture with air.
No decomposition if stored and applied as directed.
Conditions to avoid
:
Heat, flames and sparks.
Extremes of temperature and direct sunlight.
Incompatible materials
:
Strong oxidizing agents
Hazardous decomposition
products
:
Carbon oxides
Smoke
Solubility(ies)
Viscosity
SECTION 10. STABILITY AND REACTIVITY
6 / 12
Page 7
SAFETY DATA SHEET
A00141 MST STAINLESS STL CLNR/PLSH 20N15
Version 1.4
Revision Date 02/25/2017
Print Date 05/05/2017
Aggravated Medical
Condition
:
None known.
Symptoms of Overexposure
:
Effects are immediate and delayed.
Symptoms may include irritation, redness, pain, and rash.
Effects are dependent on exposure (dose, concentration,
contact time).
IARC
No component of this product present at levels greater than or
equal to 0.1% is identified as probable, possible or confirmed
human carcinogen by IARC.
OSHA
No component of this product present at levels greater than or
equal to 0.1% is identified as a carcinogen or potential
carcinogen by OSHA.
NTP
No component of this product present at levels greater than or
equal to 0.1% is identified as a known or anticipated carcinogen
by NTP.
40 CFR Protection of Environment; Part 82 Protection of
Stratospheric Ozone - CAA Section 602 Class I
Substances
Remarks
This product neither contains, nor was manufactured
with a Class I or Class II ODS as defined by the U.S.
Clean Air Act Section 602 (40 CFR 82, Subpt. A, App.A
+ B).
Do not dispose of waste into sewer.
Do not contaminate ponds, waterways or ditches with
chemical or used container.
Dispose of in accordance with local regulations.
Contaminated packaging
:
Empty remaining contents.
Dispose of as unused product.
Do not re-use empty containers.
Do not burn, or use a cutting torch on, the empty drum.
No substances are subject to a Significant New Use Rule.
No substances are subject to TSCA 12(b) export notification
requirements.
SECTION 13. DISPOSAL CONSIDERATIONS
Disposal methods
SECTION 14. TRANSPORT INFORMATION
The product as delivered to the customer conforms to packaging requirements for shipment by road
under US Department of Transportation (DOT) regulations. Additional transportation classifications
noted above are for reference only, and not a certification or warranty of the suitability of the packaging
for shipment under these alternative transport regulations.
SECTION 15. REGULATORY INFORMATION
EPCRA - Emergency Planning and Community Right-to-Know Act
CERCLA Reportable Quantity
This material does not contain any components with a CERCLA RQ.
SARA 304 Extremely Hazardous Substances Reportable Quantity
10 / 12
Page 11
SAFETY DATA SHEET
A00141 MST STAINLESS STL CLNR/PLSH 20N15
Version 1.4
Revision Date 02/25/2017
Print Date 05/05/2017
SARA 311/312 Hazards
:
Fire Hazard
Sudden Release of Pressure Hazard
Acute Health Hazard
SARA 302
:
No chemicals in this material are subject to the reporting
requirements of SARA Title III, Section 302.
SARA 313
:
This material does not contain any chemical components with
known CAS numbers that exceed the threshold (De Minimis)
reporting levels established by SARA Title III, Section 313.
California Prop 65
This product does not contain any chemicals known to State of
California to cause cancer, birth defects, or any other
reproductive harm.
TSCA
On TSCA Inventory
DSL
All components of this product are on the Canadian DSL
NFPA:
HMIS III:
Flammability
Health
Instability
3
4 0
Special hazard.
FLAMMABILITY
PHYSICAL HAZARD
HEALTH
4
2
3
0 = not significant, 1 =Slight,
2 = Moderate, 3 = High
4 = Extreme, * = Chronic
This material does not contain any components with a section 304 EHS RQ.
The components of this product are reported in the following inventories:
For information on the country notification status for other regions please contact the
manufacturer’s regulatory group.
Inventory Acronym and Validity Area Legend:
TSCA (USA), DSL (Canada), NDSL (Canada)
SECTION 16. OTHER INFORMATION
Further information
OSHA - GHS Label Information:
11 / 12
Page 12
SAFETY DATA SHEET
A00141 MST STAINLESS STL CLNR/PLSH 20N15
Version 1.4
Revision Date 02/25/2017
Print Date 05/05/2017
Hazard pictograms
:
Signal word
:
Danger:
Hazard statements
:
Extremely flammable aerosol. Contains gas under pressure; may explode if heated.
May cause an allergic skin reaction.
Precautionary statements
:
Prevention: Keep away from heat/sparks/open flames/hot surfaces. No smoking. Do
not spray on an open flame or other ignition source. Pressurized container: Do not
pierce or burn, even after use. Avoid breathing dust/ fume/ gas/ mist/ vapours/ spray.
Contaminated w ork clothing should not be allowed out of the workplace. Wear
protective gloves.
Response: IF ON SKIN: Wash with plenty of soap and w ater. If skin irritation or rash
occurs: Get medical advice/ attention. Wash contaminated clothing before reuse.
Storage: Protect from sunlight. Do not expose to temperatures exceeding 50 °C/ 122
°F.
Disposal: Dispose of contents/container in accordance with local regulation.
Version:
1.4
Revision Date:
02/25/2017
Print Date:
05/05/2017
We believe the statements, technical information and recommendations contained herein are
reliable, but they are given without warranty or guarantee of any kind. The information in this
document applies to this specific material as supplied. It may not be valid for this material if it
is used in combination with any other materials. Users should make their own investigations
to determine the suitability and applicability of the information for their particular purposes.
This SDS has been prepared by the Compliance Services organization supporting this
manufacturer, supplier or distributor.
Zep Inc. markets products under well recognized and established brand names such as Zep®,
Zep Commercial®,Zep Professional®, Enforcer®, National Chemical™, Selig™, Misty®, Next
Dimension™, Petro®, i-Chem®, TimeMist®, TimeWick™, MicrobeMax®, Country Vet®,
Konk®, Original Bike Spirits®, Blue Coral®, Black Magic®, Rain-X®, Niagara National™, F C
Forward Chemicals®,Rexodan®, Mykal™, and a number of private labeled brands.
12 / 12
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.