Mistral MFD-500R User Manual

USER’S MANUAL

POWER TOWER FAN

MODEL : MFD-500R

Please read the instruction manual carefully before

operating the appliance

1

GENERAL SAFETY PRECAUTIONS

1. This appliance is intended for indoor and household use only; not for outdoor,
commercial and industrial use. No responsibility is accepted for damage resulting
from improper use or noncompliance with the instructions.

2. Please keep this instruction manual for future reference. If the appliance is passed to
another person, this manual should accompany it.

3. Before inserting the main plug into the socket, check the main supply voltage and

current rating corresponds with the power supply details shown on the appliance’s

model label.

4. Never leave the appliance unattended while it is still connected to the power supply.

5. Do not place the appliance on or near to a gas or electric burner, heated oven, or
near to flammable materials.

6. To protect against fire, electric shock and injury, do not immerse power cord, plug or
appliance in water or other types of liquid.

7. Use only original accessories supplied.

8. Always unplug the appliance from the wall socket when it is not in use.

9. Do not unplug the appliance from the wall socket with wet hands.

10. Do not pull on the power cord to remove the plug from wall socket.

11. Do not coil the power cord too tightly around the appliance, to prevent damage to the
power cord and appliance.

12. Do not let power cord hang over the edge of table or touches any hot surfaces.

13. Ensure that the appliance is fully assembled before plugging it into the wall socket.

14. Do not insert or allow objects to enter any ventilation or exhaust opening as this may
damage the product and could cause an electric shock or fire.

15. This appliance should not be used by the physically challenged, slow response or
mentally disabled people (including children) unless guidance is provided during
operation.

2

PARTS IDENTIFICATION

Control Panel

Display Panel

1. Base

2. Front Housing

3. Blade Rod

4. Cross Blade

5. Air Line A

6. Control Panel

7. Display Panel

8. Remote Control
Compartment

9. Back Cover

10. Rear Housing

3

Accessories

SPECIFICATIONS

Model

MFD-500R

Rated Voltage

220-240V~

Rated Power

65W

Frequency

50Hz

FUNCTIONS & FEATURES

1. 3 wind modes: Natural/ Normal/ Sleeping;

2. 3 wind speeds: Hi/ Mid/ Low;

3. Horizontal Oscillation within 80 ° angle;

4. 1, 2, 4, 8 hours timing;

5. LED display, elegant and fashion

6. Easy control with remote control within 5 meters range 120° angle;

7. ECO function, humanity and energy saving.

8. Wind speed ≥11m/

HOW TO USE TOWER FAN

Before Using

 Please read these instructions carefully before use and keep it for future reference.
 Check your local main voltage whether it is the same as stated on the appliance.
 Before using for the first time, remove any protective films or stickers from the tower

fan.

 Ensure the power switch is at “OFF” position, when inserting the plug.

Remote Control

4

Assembly of Tower Fan

1. Open the package and get out the unit: Check whether the parts are complete,

Including Warranty Card, Instruction Manual, Remote Controller, Disc Screw.

2. Finish assembling as shown below.

1) Put the fan on soft place (to avoid any scratches to the fan surface)

2) Install the front base and back base to a whole unit. Attention that the base U hole’s

direction should be the same as the power cord, make sure that the power cord in the
U hole after completing assembling;

3) Place the fan well and power on, then operate the fan according to the instruction

manual.

Operation of Tower Fan

Touch- Button: Trigger the corresponding functions by touching the keys on operation
panel.

POWER ON

Buzzer “ bi-bi”, the system is in standby mode, without work.

Step 1

Step 2

5

ON/ SPEED
a. Press the ON/SPEED button to turn on the appliance, the system originally set on
“Mid” speed, shift to “Low” automatically after 3 seconds;

b. The system retains the working conditions set before turn OFF under the condition of
unplugging the socket after start-up (Not the first boot).

c. Shift wind speed with SPEED button as the rule of: Low- Mid- Hi- Low…
d. LED lights show according to Low/ Mid/ Hi speed

STAND-BY

Press the STAND-BY button, all lights off, the system stays in standby mode.

MODE

a. Press MODE to shift wind modes as following under cooling condition after start-up:
Normal – Natural – Sleep – Normal… and the LED display will show accordingly.
The system originally set as Normal.

b. Normal: The machine works in constant speed according to the setting of Hi, Mid,
Low. LED shows corresponding speed, the sign of Normal Mode displayed.

c. Natural: Fan motor runs rhythmically. The Natural wind comes to Hi, Mid, Low by
shifting wind speed. Generating softer and more comfort air volume feels like wind
from nature. LED shows corresponding speed. (eg: LED shows “Hi “ light in high
normal wind, shows “Low” light in low natural wind. LED doesn’t change with the
waveform.)

Waveform of natural wind as following:

6

d. Sleep: Fan motor under computer program control in Sleep Mode. Air volume
will reduce with the decrease of room temperature, which protect human from
catching cold. It reduce as below rule.

- The unit works for half an hour in Hi natural wind, then shift to Mid natural wind,

then to Low half an hour later, till the end of preset time or turned off under the
setting of Hi sleeping wind mode;

- The unit works for half an hour in Mid natural wind, then shift to Low natural wind,

till the end of preset time or turned off under the setting of Mid sleeping wind
mode;

- The unit works in Low natural wind, till the end of preset time or turned off under

the setting of Mid sleeping wind mode;

- LED shows corresponding speed. (Same as Natural Mode)

TIMER

a. Timer is used to set the time of turning off, the unit will shut down automatically when
time reduced to 0h;

b. The system start-up without timing and LED display. Press TIME to set working time
as the rule of 1h-2hs-4hs- 8hs- without timing- 1h…, LED lights shows accordingly;

c. LED shows the left time when working, the unit shut down when time is over with
buzzing.

SWING

a. Press SWING to control the swing function after start up, original setting without
swing.

b. LED lights display accordingly.
ECO

a. Press ECO, system under ECO mode, LED display accordingly.
b. Running Rule of ECO mode: 27°C set by system.

The appliance will auto adjust according to room temperature, which the unit works in
Low speed when ambience temperature < 25°C; in Hi speed when
> 29°C; in Mid speed when 25°C ~29°C.

7

Remote Controller Instructions

1. Open the cover at the back of the controller. Install a battery of 3V CR2032.

2. Align with the receiver when work.

3. Replace battery when it’s power off, pull out the cover as shown. Please mind the

Plus-n- Minus of the battery. The controller will restart by putting back the cover.

CLEANING & MAINTENANCE

1. Clean this appliance regularly to ensure maximum performance.

2. Always unplug the product from the wall socket and let it cool down completely prior

to cleaning.

3. Do not use abrasive sponge, scouring pads or stiff brush to clean the appliance.

4. Please be cautious when cleaning the product especially near motor housing area.

5. Use only damp cloth to wipe the external surface of the unit. Do not immerse the

main body in water.

6. Do not allow the motor or other electrical components to be exposed to water.

7. For proper storage, always place the appliance in a low humidity environment.

8

THIS APPLIANCE IS STRICTLY FOR HOUSEHOLD USE ONLY

Distributed by:

KHIND ALLIANCES SDN BHD (811092-W)

No.2, Jalan Astaka U8/82, Seksyen U8,

Bukit Jelutong, 40150 Shah Alam, Selangor D.E., Malaysia.
Tel: [phone] Fax: [phone]
Customer Care line: 1300 8000 32

Website: www.khindalliances.com | www.mistral.com.my

Email: [e-mail]