Page 1
Assembly Instruction Sheet
ToolsRequired: Flathead screwdriver,Phillipsscrewdriver,pliers, wire cutters, wire strippers, electrical tape, safety glasses.
LightSource:
EstimatedAssembly Time:
Preparation:
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
(6)CandelabraBaseBulbs60WMaximum
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
Package Contents
Glass Panel
C
x6
Fixture Body
B
x1
Upper
Assembly
A
x1
Lock Screw
D
x12
Rubber Washer
E
x12
STEP 1 - Install the Crossbar to the junction box
A. Attach the Crossbar (AA) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included), tighten until snug.
Outlet Box
AA
Outlet Box Screw
(not included)
Figure 1
STEP 2 Install Nipple to Crossbar-
A. Thread one Hex Nut (CC) to the middle of the Nipple (DD). Place the
Lock Washer (BB) over the Nipple (DD) and then thread the Nipple
(DD) into the Crossbar (AA) until the Nipple (DD) is about 0.375”
above the Crossbar (AA).
B. Place the Ceiling Canopy (HH) over the Nipple (DD) against the
ceiling to determine the correct position of the Nipple (DD). Thread
the Lock Ball (EE) onto the Nipple (DD). Adjust the Nipple (DD) to
allow the Ceiling Canopy (HH) to rest against the ceiling when held
in place by the Lock Ball (EE).
C. Remove the Ceiling Canopy (HH) and then tighten the Hex Nut (CC)
against the Crossbar (AA) to secure in place.
Hardware Contents
Crossbar
AA
x1
Lock Washer
BB
x1
Hex Nut
CC
x2
DD
Mounting Ball
EE
x1
FF
Quick Link
GG
x4
Nipple
x1
Fixture Chain
x2
Ceiling
HH
Canopy
x1
1of3
AA
BB
CC
DD
HH
EE
Figure 2
Page 2
STEP 3 Install Upper Assembly to Fixture Body-
STEP 5 - Attach the Lanyard
A. Unlock the screw on the hook until there is enough space for the
loop end of the side rod. Attach the end of the side rod to the hook on
the top of the Fixture Body (B) and tight the screw on the hook to
prevent the side rod slip out of the hook.
Supply Wires and
Ground Wire
A
Side Rod
Hook
B
Screw
Figure 3
STEP 4 - Install Fixture Chains
A. Adjust the Fixture Chain (FF) to your desired length by removing the
links if needed.
B. With the Fixture Chain (FF) not attached to the loops on the top of
the Upper Assembly (A) and the ceiling loops underside of the
Ceiling Canopy (HH), pull the supply wires and ground wire through
the Fixture Chain (FF) alternating links. After the wires are through
the Fixture Chain (FF), pull the Supply Wires and the Ground Wire
through the Ceiling Canopy (HH).
C. Attach one ends of the Fixture Chains (FF) to loops on top of the
Upper Assembly (A) with two Quick Links (GG) as shown. Lift the
fixture and Fixture Chains (FF) up and attach the other ends of the
Fixture Chains (FF) onto ceiling loops underside of the Ceiling
Canopy (HH) with the rest two Quick Links (GG).
Suggested rods and chain length for Ceiling height :
8’ ceiling : use 7 links of chains and 4 quick links
9’ ceiling : use 17 links of chains and 4 quick links
10’ ceiling : use 27 links of chains and 4 quick links
HH
GG
FF
Supply Wires and
Figure 4
GG
Ground Wire
A
A. The purpose of the lanyard is to provide a means to support the
fixture hands free from the junction box while connecting the
electrical wires.
B. Turn the Button Stop so it may be inserted into a Crossbar slot. Make
sure the Button Stop is
completely inside the
Crossbar. Slowly release
the fixture to make sure it is
supported by the Button
Stop. Proceed to the wiring
Crossbar
Lanyard
Slot
Button
Stop
steps in the next step. Once
you are complete with the
wiring, the Lanyard will
push into the junction box
when the fixture is placed
for final mounting.
Figure 5
STEP 6 - Making the Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into outlet box.
Note: If the electrical wire is going to be cut shorter than provided
you will need to identify the "L" line wire and the "N" neutral wire
before you cut the excess wire off. One is labeled N and the other
labeled L. To do this separate the "L" line wire and the "N" neutral
wire as far as you need to. Re-label the wire near where you want to
make the cut. Be sure to mark the wire on the side of the fixture and
not on the excess wire being cut and removed.
White wire
from outlet box
Black wire from
outlet box (or Red)
Bare, or Green
Ground wire
from outlet box
Bare, or Green
Ground wire
from outlet box
OR
Ribbed side of wire from fixture
identified with the Label “N”
Smooth side of wire from fixture
identified with the label “L”
Ground wire
from fixture
Ground wire
from fixture
Figure 6
Green Ground Screw
on the Crossbar
STEP 7 Install Ceiling Canopy to Crossbar-
A. Attach the Ceiling Canopy (HH) over the end of the Nipple (DD) and
secure with the Hex Nut (CC). Hand tighten until snug.
B. Thread the Mounting Ball (EE) onto the Nipple (DD) and hand
tighten until snug.
DD
2of3
HH
CC
EE
Figure 7
Page 3
STEP 8 Install Glass Panels and Bulbs-
A. Align holes on the Glass Panel (D) to mounting holes on the frame of
the Fixture Body (C). Place the Rubber Washer (F) onto the Lock
Screw (E) and thread Lock Screws with Rubber Washers into the
mounting holes on the frame to secure the Glass Panel (D). Hand
tighten until snug.
B. Insert bulbs onto sockets and screw snugly into place.
Your fixture is now assembled and ready to use. Enjoy!
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/4"
FINISH: MOTTLED SILVER
4.5”
12”
Bulb (not
supplied)
C
F
E
D
Socket
Figure 8
76.75” OVERALL HEIGHT
INCLUDES 48” CHAINS
AND 4 QUICK LINKS()
13”
39”
23.5”
8.25”
15.5”
3of3
Loading...