Mistana MITN1784 Assembly Instruction

Assembly Instruction
ToolsRequired: Flatheadscrewdriver,Phillipsscrewdriver,pliers,wire cutters,wirestrippers, electricaltape,safety glasses. LightSource: EstimatedAssembly Time: Preparation:
present.Ifany partsaremissing ordamaged,do notattemptto assemble,install,or operatethefixture. Contactcustomerservice forreplacement parts.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
(3)A19 MediumBaseBulbs 60WMaximum
30-45minutes
Identifyandinspect allpartsbefore beginninginstallation.Check packagecontentlist anddiagramsbelow tobesure allpartsare
Package Contents
Crossbar Assembly
A
x1
C
Diffuser
D
x1
STEP 1 - Install Diffuser and Glass Panels
A. Insert the Diffuser (D) in the bottom of the
Cage (C) and secure by folding tabs in the bottom edge of the Cage (C).
Install the Glass Panel ( ) into the
B. E side of the
Cage ( ) and secure by folding tabs in the top
C and bottom of the Cage ( ). Repeat this process to complete installation of all Glass Panels ( ).
E
C
Cage x1
Fixture Body
B
x1
Glass Panel
E
x18
E
STEP 2 - Installing the Crossbar Assembly
A. Pass the supply wires from outlet box through the Crossbar
Assembly (A). Attach the Crossbar Assembly (A) to the Outlet Box with the head of the Green Ground Screw facing you. Secure the Crossbar Assembly (A) with Outlet Box Screws (not included). Tighten until snug.
Outlet Box
A
Outlet Box Screws (not included)
Figure 2
STEP 3 Test Fitting Ceiling Canopy to Crossbar Assembly-
A.
Remove mounting balls from the CrossbarAssembly (A). Fit the
eiling canopy to the
c and Fixture Body (B) Crossbar Assembly (A) and secure with mounting balls. Note: The should be snug against the and the mounting balls. If length of the nipple on the Crossbar Assembly (A) by unscrewing the preassembled hex nut and lock washer and then screwing the mounting screws in or out of the crossbar until the correct length is achieved. Once the ceiling canopy and Fixture Body (B) is secure, remove the mounting ball and ceiling canopy and Fixture Body (B) and proceed to Step 4.
ceiling
Supply Wires with Ground Wire
ceiling canopy
not, adjust the
Figure 1
D
Tab
C
Tab
1of2
Mounting Screw
B
Mounting Ball
A
Figure 3
Hex Nut and Lock Washer
STEP 4 - Wire Connections
A. Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the green ground screw.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together. Wrap each connection with approved electrical tape and carefully stuff all the connected wires into the Outlet Box.
FINISH: AGEDGOLD
White wire
from outlet box
Black wire from
outlet box (or Red)
Bare, or Green
Ground wire
from outlet box
Green Ground Screw on the Crossbar
White wire from fixture
Black wire from fixture
Ground wire from Fixture
Figure 4
STEP 5 Install the Fixture-
A. Carefully tuck all wires into the outlet box and position the ceiling
canopy and Fixture Body (B) over the outlet box.Align the holes in the ceiling canopy with the mounting screws, then attach the canopy and Fixture Body (B)
using the previously removed
ceiling
mounting balls. Hand tighten until snug.
A
B
Mounting Screw
Mounting Ball
13.25” Dia.
7”
5.5”
15” Dia. 16” Dia.
2.5”
Figure 5
STEP 6 Install Cage and Bulbs-
A. Remove lock screws from the side of the ceiling canopy. B. Insert bulbs onto sockets and screw snugly into place. C. Lift the cage with glass panels upward and align the holes on tabs at
the top edge of the Cage (C) to mounting holes on the side of the ceiling canopy. Secure them by threading previously removed lock screws back into mounting holes. Hand tighten until snug.
Your fixture is now assembled and ready to use. Enjoy!
Ceiling Canopy
Lock Screw
B
Bulb (not supplied)
Socket
Tab
C
Figure 6
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/4"
2of2
Loading...