Release: AOS 5.0
September 2010
Part Number: 010-00822c
This manual supports Archiving Operating System (AOS) release 5.0 and later releases, and
RazorSafe 7-Series appliances, until replaced by a newer edition.
Mirapoint, RazorGate, and the Mirapoint logo are registered trademarks of Mirapoint Software, Inc.
Mirapoint Message Server, Mirapoint Directory Server, Mirapoint Operations Console, RazorSafe, DirectPath,
WebMail Direct, WebCal Direct, and GroupCal Direct are trademarks of Mirapoint Software, Inc.
Mirapoint integrates third party software programs within the Mirapoint Software, which are subject to their
own license terms. If the user does not agree to abide by the applicable license terms for the integrated third
party software programs as defined by the Mirapoint Software License Agreement, then you may not install or
operate the Mirapoint Software. These software license agreements, including the Mirapoint Software License
Agreement, Red Hat End User License Agreement, and Open LDAP Public License, can be viewed at http://
OpenLDAP is a registered trademark of the OpenLDAP Foundation.
Macintosh is a trademark of Apple Computer, Inc.
Windows, Outlook, Exchange, and Active Directory are trademarks of Microsoft Corporation.
Java and Solaris are trademarks of Sun Microsystems, Inc.
Linux is a registered trademark of Linus Torvalds.
All other trademarks are the property of their respective owners.
OTHER THAN ANY EXPRESS LIMITED WARRANTIES THAT MIRAPOINT PROVIDES TO YOU IN
WRITING, MIRAPOINT AND MIRAPOINT'S LICENSORS PROVIDE THE SOFTWARE TO YOU “AS IS”
AND EXPRESSLY DISCLAIM ALL WARRANTIES AND/OR CONDITIONS, EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL MIRAPOINT'S LICENSORS BE LIABLE
FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY OR CONSEQUENTIAL
DAMAGES, HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY (INCLUDING NEGLIGENCE
OR OTHER TORT), ARISING IN ANY WAY OUT OF YOUR USE OF THE SOFTWARE, EVEN IF
ADVISED OF THE POSSIBILITY OF DAMAGES. MIRAPOINT’S LIABILITY SHALL BE AS LIMITED IN
THE LICENSE AGREEMENT.
The following provides information and procedures for getting started with a
Mirapoint RazorSafe 170 (RS170).
1
c
Before performing the following procedures, review the safety instructions provided
with the appliance.
Obtaining Technical Assistance
If you need help understanding a procedure in this guide or if the appliance
performs unexpectedly, see Additional Information on page 15 and the Mirapoint RazorSafe 170 (RS170) Hardware Guide.
Overview
Installing and configuring your appliance involves the following tasks:
◆Unpacking the Appliance on page 6
◆Installing the Rails and Appliance in a Rack on page 6
◆Connecting Keyboard, and Monitor on page 6
◆Connecting the Power Cable on page 7
◆Securing the Power Cord on page 7
◆Powering the Appliance on page 8
◆Installing the Bezel (Optional) on page 8
◆Completing the Operating System Setup on page 8
5
Mirapoint RazorSafe 170 (RS170) Installation
1
Unpacking the Appliance
Unpack your appliance and identify each item.
Installing the Rails and Appliance in a Rack
c
If installed in a closed or multi-unit rack assembly, the operating ambient
temperature of the rack environment might be greater than room ambient
temperature. Consider installing the equipment in an environment compatible with
the maximum ambient temperature (Tma) specified by the manufacturer. For more
information, see RS170 Technical Specifications on page 16.
Following the safety instructions provided in your appliance box and the rack
installation instructions provided with in the rail kit, assemble the rails and install
the appliance in the rack.
Connecting Keyboard, and Monitor
Connect a keyboard, and monitor (not included).
The connectors on the back of your appliance have icons indicating which cable to
plug into each connector. Be sure to tighten the screws (if any) on the monitor's
cable connector.
6
Connecting the Power Cable
Connect the appliance’s power cable to the appliance, and connect the monitor’s
power cable to the monitor.
Securing the Power Cord
Bend the appliance power cable into a loop as shown in the illustration and secure
the cable to the bracket using the provided strap.
Plug the other end of the power cable into a grounded electrical outlet or a separate
power source such as an uninterruptible power supply (UPS) or a power
distribution unit (PDU).
Connecting the Power Cable
Connecting Ethernet Cables
Mirapoint recommends the use of Category 5 patch cables; port connections are
standard RJ-45.
Designated Ethernet Port
7
Mirapoint RazorSafe 170 (RS170) Installation
1
Powering the Appliance
Press the power button on the appliance and the monitor. The power indicators
illuminate.
Installing the Bezel (Optional)
b
A lock on the bezel restricts access to the power button, optical drive, and hard
drives. The LCD panel and navigation buttons are accessible through the front
bezel.
Install the bezel (optional).
Completing the Operating System Setup
The Archiving Operating System (AOS) is pre-installed on all Mirapoint RazorSafe
appliances. Once your appliance is physically installed and powered on, you must
complete the software configuration as described in the Mirapoint RazorSafe Software Configuration Guide.
n
For the latest information on AOS support, see support.mirapoint.com.
8
Mirapoint RazorSafe 700 (RS700)
Installation
The following provides information and procedures for getting started with a
Mirapoint RazorSafe 700 (RS700).
2
c
Before performing the following procedures, review the safety instructions provided
with the appliance.
Obtaining Technical Assistance
If you need help understanding a procedure in this guide or if the appliance
performs unexpectedly, see Additional Information on page 15 and the Mirapoint RS700 Hardware Guide.
Overview
Installing and configuring your appliance involves the following tasks:
◆Unpacking the Appliance on page 10
◆Installing the Rails and Appliance in a Rack on page 10
◆Connecting Keyboard, and Monitor on page 10
◆Connecting the Power Cables on page 11
◆Securing the Power Cord on page 11
◆Powering the Appliance on page 12
◆Installing the Bezel (Optional) on page 12
◆Completing the Operating System Setup on page 13
9
Mirapoint RazorSafe 700 (RS700) Installation
2
Unpacking the Appliance
Unpack your appliance and identify each item.
Installing the Rails and Appliance in a Rack
c
If installed in a closed or multi-unit rack assembly, the operating ambient
temperature of the rack environment might be greater than room ambient
temperature. Consider installing the equipment in an environment compatible with
the maximum ambient temperature (Tma) specified by the manufacturer. For more
information, see RS700 Technical Specifications on page 19.
Following the safety instructions provided in your appliance box and the rack
installation instructions provided with in the rail kit, assemble the rails and install
the appliance in the rack.
Connecting Keyboard, and Monitor
Connect a keyboard, and monitor (not included).
10
The connectors on the back of your appliance have icons indicating which cable to
plug into each connector. Be sure to tighten the screws (if any) on the monitor's
cable connector.
Connecting the Power Cables
Connect the appliance’s power cables to the appliance, and connect the monitor’s
power cable to the monitor.
Securing the Power Cord
Bend the appliance power cable into a loop as shown in the illustration and secure
the cable to the bracket using the provided strap.
Plug the other end of the power cables into a grounded electrical outlet or
a separate power source such as an uninterruptible power supply (UPS) or a power
distribution unit (PDU).
Connecting the Power Cables
b
For improved redundancy, Mirapoint recommends connecting the two power
supplies to separate circuits, but never mixing the voltages.
For example: Do not plug one power supply into a 120V current and the other
power supply into a 240V current.
11
Mirapoint RazorSafe 700 (RS700) Installation
2
Connecting Ethernet Cables
Mirapoint recommends the use of Category 5 patch cables; port connections are
standard RJ-45.
Designated Ethernet Port
Powering the Appliance
Press the power button on the appliance and the monitor. The power indicators
illuminate.
Installing the Bezel (Optional)
b
12
A lock on the bezel restricts access to the power button, optical drive, and hard
drives. The LCD panel and navigation buttons are accessible through the front
bezel.
Install the bezel (optional).
Completing the Operating System Setup
Completing the Operating System Setup
The Archiving Operating System (AOS) is pre-installed on all Mirapoint RazorSafe
appliances. Once your appliance is physically installed and powered on, you must
complete the software configuration as described in the Mirapoint RazorSafe Software Configuration Guide.
n
For the latest information on AOS support, see support.mirapoint.com.
13
Mirapoint RazorSafe 700 (RS700) Installation
2
14
Additional Information
The following provides additional information relevant to a Mirapoint appliance.
Provided information includes:
◆Other Information You Might Need
◆Technical Specifications on page 16
◆NOM Information (Mexico Only) on page 21
Other Information You Might Need
3
n
n
See the safety, regulatory, and warranty information which accompanies your
appliance.
◆The rack documentation, included in the rail kit, describes how to install the
rack rails and mount your appliance on to the rack rails.
◆The Mirapoint RazorSafe 170 (RS170) Hardware Guide and Mirapoint
RazorSafe 700 (RS700) Hardware Guide provide information about the
appliance features and describe how to troubleshoot the appliance and install or
replace appliance components. These documents are available online at
support.mirapoint.com.
◆The CD and DVD media, which accompanies these instructions within the
folio, provides documentation and tools for configuring and managing your
appliance.
Always first check for updates online at support.mirapoint.com, and read any
updates, because they often supersede information in other documents.
15
Additional Information
3
Technical Specifications
RS170 Technical Specifications
Processor
Processor type
Bus typePCI Express Generation 2
Memory capacity8GB DDR3
Hard drivesTwo 3.5-inch cabled SATA internal drives
Optical driveOne internal slimline SATA DVD-ROM
Single Quad-core Intel
Expansion Bus
Memory
Drives
Connectors
®
Xeon
®
Back
NICTwo RJ-45 (for integrated 1-GB NICs)
Serial9-pin, DTE, 16550-compatible
USBTwo 4-pin, USB 2.0-compliant
Video15-pin VGA
eSATAOne 7-pin connector
Front
Video15-pin VGA
USBTwo 4-pin, USB 2.0-compliant
Internal
USBOne 4-pin, USB 2.0-compliant
16
Technical Specifications
Power
AC Power Supply
Wattage250W
Voltage100-240 VAC, 50/60 Hz, 4-2 A
Heat dissipation1039 BTU/hr maximum
Maximum inrush currentUnder typical line conditions and over the entire
system ambient operating range, the inrush
current might reach 25 A.
Batteries
Appliance batteryCR 2032 3.0-V lithium ion coin cell
Physical
Height4.24 cm (1.67 in)
Width43.4 cm (17.09 in)
Depth39.37 cm (15.5 in)
Weight (maximum configuration)8.058 kg (17.77 lb)
Environmental
Temperature
Operating10° to 35°C (50° to 95°F) with a maximum
temperature gradation of 10°C per hour
NOTE: For altitudes above 2950 feet, the
maximum operating temperature is derated
1°F/550 ft.
Storage–40° to 65°C (–40° to 149°F) with a maximum
temperature gradation of 20°C per hour
Relative humidity
Operating20% to 80% (non-condensing) with a
maximum humidity gradation of 10% per hour
Storage5% to 95% (non-condensing) with a maximum
Maximum vibration
Operating0.26 Grms at 5–500 Hz for 15 min
17
humidity gradation of 10% per hour
Additional Information
3
Storage1.54 Grms at 10–250 Hz for 15 min
Maximum shock
OperatingOne shock pulse in the positive z axis (one pulse
StorageSix consecutively executed shock pulses in the
Altitude
Operating–16 to 3048 m (–50 to 10,000 ft)
Storage–16 to 10,600 m (–50 to 35,000 ft)
Airborne Contaminant Level
Environmental (Continued)
on each side of the system) of 31 G for 2.6 ms
in the operational orientation
positive and negative x, y, and z axes (one pulse
on each side of the system) of 71 G for up to
2 ms
For altitudes above 2950 feet, the maximum
operating temperature is derated 1°F/550 ft.
ClassG2 or lower as defined by ISA-S71.04-1985
NOM Information (Mexico Only)
The following information is provided on the device described in this document in
compliance with the requirements of the official Mexican standards (NOM):
Exporter:Mirapoint Software, Inc.
1215 Bordeaux Drive
Sunnyvale, CA 94089
408-720-3700
Hard drivesSix 3.5-inch, internal, hot-swappable SAS hard drives.*
Optical driveOne internal slimline SATA DVD-ROM
*If you purchased your hardware before September 15, 2010, your configuration is
different. For details, contact your Mirapoint representative.
Connectors
Back
NICFour RJ-45 10/100/1000 Mbps Ethernet
Serial9-pin, DTE, 16550-compatible
Video15-pin VGA
Front
Video15-pin VGA
19
Additional Information
3
AC Power Supply (per power supply)
Wattage870 W (Max.)
Voltage90–264 VAC, autoranging, 47-63 H
Heat dissipation2968.6 BTU/hr maximum (Max.)
Power
Maximum inrush
current
Batteries
Appliance batteryCR 2032 3.0-V lithium coin cell
RAID battery 3.7-V lithium ion battery pack
Under typical line conditions and over the entire
ambient operating range, the inrush current
might reach 55 A per power supply for 10 ms or
less.
Physical
Height8.64 cm (3.4 in)
Width48.24 cm (18.99 in) with rack latches
44.31 cm (17.4 in) without rack latches
Depth72.06 cm(28.4 in) with power supplies and bezel
68.07 cm(26.8) without power supplies and bezel
Weight (maximum configuration)26.1 kg (57.54 lb)
Weight (without hard drives)17.7 kg (39 lb)
Temperature
Operating10° to 35°C (50° to 95°F) with a maximum
Storage–40° to 65°C (–40° to 149°F) with a maximum
Relative humidity
Operating20% to 80% (non-condensing) with a maximum
20
Environmental
temperature gradation of 10°C per hour
For altitudes above 2950 feet, the maximum
operating temperature is derated 1°F/550 ft.
temperature gradation of 20°C per hour
humidity gradation of 10% per hour
Technical Specifications
Environmental (Continued)
Storage5% to 95% (non-condensing) with a maximum
humidity gradation of 10% per hour
Maximum vibration
Operating0.26 Gms from 5–350 Hz for 5 minutes in
operational orientations
Storage1.54 Gms from 10–250 Hz for 10 minutes in all
orientations
Maximum shock
OperatingHalf sine shock in all operational orientations of
31 G plus or minus 5% with a pulse duration of
2.6 ms plus or minus 10%
StorageHalf sine shock on all six sides of 71 G plus or
minus 5% with a pulse duration of 2 ms plus or
minus 10%
Square wave shock on all six sides of 27 G with a
velocity change at 235 in/sec or greater
Altitude
Operating–16 to 3048 m (–50 to 10,000 ft)
For altitudes above 2950 feet, the maximum
operating temperature is derated 1°F/550 ft.
Storage–16 to 10,600 m (–50 to 35,000 ft)
NOM Information (Mexico Only)
The following information is provided on the device described in this document in
compliance with the requirements of the official Mexican standards (NOM):
Exporter:Mirapoint Software, Inc.
1215 Bordeaux Drive
Sunnyvale, CA 94089
408-720-3700
MIRAPOINT SOFTWARE, INC. SOFTWARE LICENSE AGREEMENT
PLEASE READ THIS SOFTWARE LICENSE AGREEMENT (“LICENSE”) CAREFULLY BEFORE DOWNLOADING OR
OTHERWISE USING THE SOFTWARE. BY DOWNLOADING, INSTALLING OR USING THE SOFTWARE, YOU ARE
AGREEING TO BE BOUND BY THE TERMS OF THIS SOFTWARE LICENSE AGREEMENT.
IF YOU DO NOT AGREE TO THE TERMS OF THIS LICENSE, YOU ARE NOT AUTHORIZED TO DOWNLOAD OR
USE THIS SOFTWARE.
1. Scope. This License governs you (“User”) and your use of any and all computer software, any printed or electronic
documentation, or other code, whether on disk, in read only memory, or on any other media (collectively, the “Mirapoint
Software”) provided to you as part of or with a Mirapoint Product.
2. License, not Sale, of Mirapoint Software. The Mirapoint Software is licensed, not sold, to User by MIRAPOINT
SOFTWARE, INC. or its affiliate, if any (“Mirapoint”). USER MAY OWN THE MEDIA ON WHICH THE MIRAPOINT
SOFTWARE IS PROVIDED, BUT MIRAPOINT AND/OR MIRAPOINT’S LICENSOR(S) RETAIN TITLE TO THE
MIRAPOINT SOFTWARE. The Mirapoint Software installed on the Mirapoint Product and any copies which this License
authorizes the User to make are subject to this License.
3. Permitted Uses. This License allows User to use the pre-installed Mirapoint Software exclusively on the Mirapoint Product
on which the Mirapoint Software has been installed. With respect to Mirapoint Software [identified by Mirapoint as the
“administrative application”] that has not been preinstalled on the Mirapoint Product, this License allows you to copy, use
and install such Mirapoint Software on one or more administrative workstations on which the Mirapoint Software is
supported. User may make copies of the Mirapoint Software in machine-readable form for backup purposes only, provided
that such backup copy must include all copyright and other proprietary information and notices contained on the original.
4. Proprietary Rights; Restrictions on Use. User acknowledges and agrees that the Mirapoint Software is copyrighted and
contains materials that are protected by copyright, trademark, trade secret and other laws and international treaty provisions
relating to proprietary rights. User may not remove, deface or obscure any of Mirapoint’s or its suppliers’ proprietary rights
notices on or in the Mirapoint Software or on output generated by the Mirapoint Software. Except as permitted by
applicable law and this License, you may not copy, decompile, reverse engineer, disassemble, modify, rent, lease, loan,
distribute, assign, transfer, or create derivative works from the Mirapoint Software. Your rights under this License will
terminate automatically without notice from Mirapoint if you fail to comply with any term(s) of this License. User
acknowledges and agrees that any unauthorized use, transfer, sublicensing or disclosure of the Mirapoint Software may cause
irreparable injury to Mirapoint, and under such circumstances, Mirapoint shall be entitled to equitable relief, without
posting bond or other security, including but not limited to, preliminary and permanent injunctive relief.
5. Third Party Programs. Mirapoint integrates third party software programs with the Mirapoint Software which are subject
to their own license terms. These license terms can be viewed at http://www.mirapoint.com/licenses/thirdparty/eula.php. If
User does not agree to abide by the applicable license terms for the integrated third party software programs, then you may
not install the Mirapoint Software.
6. Disclaimer of Warranty on Mirapoint Software. User expressly acknowledges and agrees that use of the Mirapoint
Software is at your sole risk. Unless Mirapoint otherwise provides an express warranty with respect to the Mirapoint
Software, the Mirapoint Software is provided “AS IS” and without warranty of any kind and Mirapoint and Mirapoint’s
licensor(s) (for the purposes of provisions 5 and 6, Mirapoint and Mirapoint’s licensor(s) shall be collectively referred to as
“Mirapoint”) EXPRESSLY DISCLAIM ALL WARRANTIES AND/OR CONDITIONS, EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. IN ADDITION, MIRAPOINT DOES NOT WARRANT THAT THE MIRAPOINT SOFTWARE
WILL MEET YOUR REQUIREMENTS, OR THAT THE MIRAPOINT SOFTWARE WILL RUN UNINTERRUPTED OR
BE ERROR-FREE, OR THAT DEFECTS IN THE MIRAPOINT SOFTWARE WILL BE CORRECTED. SOME
JURISDICTIONS DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES OR OTHER DISCLAIMERS, SO
THE ABOVE EXCLUSION OR DISCLAIMERS MAY NOT APPLY TO YOU.
7. Limitation of Liability. UNDER NO CIRCUMSTANCES, INCLUDING NEGLIGENCE, SHALL MIRAPOINT BE
LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR
RELATING TO THIS LICENSE. FURTHER, IN NO EVENT SHALL MIRAPOINT’S LICENSORS BE LIABLE FOR ANY
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY OR CONSEQUENTIAL DAMAGES (INCLUDING BUT
NOT LIMITED TO PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES, LOSS OF USE, DATA OR PROFITS OR
INTERRUPTION), HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY (INCLUDING NEGLIGENCE OR
OTHER TORT), ARISING IN ANY WAY OUT OF YOUR USE OF THE SOFTWARE OR THIS AGREEMENT, EVEN IF
ADVISED OF THE POSSIBILITY OF DAMAGES. SOME JURISDICTIONS DO NOT ALLOW THE LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THIS LIMITATION MAY NOT APPLY TO YOU. In no event shall
Mirapoint’s total liability to you for all damages exceed the amount paid for this License to the Mirapoint
Software.
8. Export Control. As required by the laws of the United States and other countries, User represents and
warrants that it: (a) understands that the Mirapoint Software and its components may be subject to export
controls under the U.S. Commerce Department’s Export Administration Regulations (“EAR”); (b) is not located
in a prohibited destination country under the EAR or U.S. sanctions regulations (currently Cuba, Iran, Iraq,
North Korea, Sudan and Syria, subject to change as posted by the United States government); (c) will not
export, re-export, or transfer the Mirapoint Software to any prohibited destination or persons or entities on the
U.S. Bureau of Industry and Security Denied Parties List or Entity List, or the U.S. Office of Foreign Assets
Control list of Specially Designated Nationals and Blocked Persons, or any similar lists maintained by other
countries, without the necessary export license(s) or authorizations(s); (d) will not use or transfer the Mirapoint
Software for use in connection with any nuclear, chemical or biological weapons, missile technology, or military
end-uses where prohibited by an applicable arms embargo, unless authorized by the relevant government agency
by regulation or specific license; (e) understands and agrees that if it is in the United States and exports or
transfers the Mirapoint Software to eligible users, it will, to the extent required by EAR Section 740.17(e),
submit semi-annual reports to the Commerce Department’s Bureau of Industry and Security, which include the
name and address (including country) of each transferee; and (f) understands that countries including the United
States may restrict the import, use, or export of encryption products (which may include the Mirapoint
Software and the components) and agrees that it shall be solely responsible for compliance with any such
import, use, or export restrictions.
9. Miscellaneous. This License will be governed by and construed in accordance with the laws of the State of
California, U.S.A., without reference to its conflict of law principles. If a court of competent jurisdiction finds
any provision of this License invalid or unenforceable, that provision will be amended to achieve as nearly as
possible the same economic effect as the original provision and the remainder of this License will remain in full
force. Failure of a party to enforce any provision of this License shall not waive such provision or of the right to
enforce such provision. This License sets forth the entire agreement between the parties with respect to your use
of the Mirapoint Software and supersedes all prior or contemporaneous representations or understandings
regarding such subject matter. No modification or amendment of this License will be binding unless in writing
and signed by an authorized representative of Mirapoint. You will not export, re-export, divert, transfer or
disclose, directly or indirectly, the Mirapoint Software, Mirapoint Products or any technical information and
materials supplied under this Agreement without complying strictly with the export control laws and all legal
requirements in the relevant jurisdiction, including without limitation, obtaining the prior approval of the U.S.
Department of Commerce.
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.