User's Manual
32” LCD TV
Table of Contents
Important Safety Instructions............................................................................................................. 02
Cautions ............................................................................................................................................03
Descriptions and accessories............................................................................................................ 06
LCD TV installation & operation
Connectors and sockets.................................................................................................................... 07
Control panel keys............................................................................................................................. 11
Remote control functions................................................................................................................... 12
z Teletext ............................................................................................................................ 13
z Special Key for DVB/T ...................................................................................................... 14
TV menu
English
Using the advanced menu................................................................................................................. 15
z Display.............................................................................................................................. 16
z Advance ............................................................................................................................ 17
z Geometry........................................................................................................................... 18
z TV Setup ........................................................................................................................... 19
z Program Edit ..................................................................................................................... 20
z Audio ................................................................................................................................ 22
z System .............................................................................................................................. 23
Digital TV menu
z Digital OSD Functions....................................................................................................... 24
z First-Time Installation........................................................................................................ 24
z Main Menu......................................................................................................................... 25
Other information
Trouble-shooting................................................................................................................................ 30
Specifications ....................................................................................................................................31
S0524
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9. Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
10. Only use attachments/accessories specified by the manufacturer.
11. Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution when
moving the cart/ apparatus combination to avoid injury from tip-over.
12. Unplug this apparatus during lightning storms or when unused for long periods of
time.
13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
14. Apparatus shall not be exposed to dripping or splashing and no objects fill with liquids, such as
vases, shall be placed on the apparatus.
15. To reduce the risk of electric shock, do not remove the cover of the apparatus. Refer any servicing
to appointed service personnel.
16. The readily operable appliance coupler will serve as the disconnecting device of this apparatus.
17. The apparatus must be connected to a mains socket outlet with a protected earthed connection.
18. Maintain a minimum of 10cm free space around the apparatus for proper ventilation.
19. Used or discharged batteries must be properly disposed of or recycled in compliance with all
applicable laws. For detailed information, contact your local solid waste disposal authority.
20. When purchased or used in different countries, use an appropriate power cable which is compliant
with local laws and regulations.
21. To pr
event injury, this apparatus must be securely attached to the floor/wall in accordance with the
installation instructions
22. Do not install this equipment in a confined space such a book case or similar unit.
23. No naked flame sources, such as lighted candles,should be placed on the apparatus.
installation instructions.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT
TO RAIN OR MOISTURE.
This symbol is used to indicate uninsulated "dangerous voltage" within the product's
enclosure that may cause electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to the
important operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
"CAUTION"
These servicing instructions are for use by qualified service personnel only. To reduce the risk of
electric shock do not perform any servicing other than that contained in the operating instructions
unless you are qualified to do so.
2 ..................................................................................................................................................................
Cautions
[Caution]
To protect your device from electrical damage, be sure to plug the cord into socket securely.
[Caution]
If you use the LCD TV with video games, computers, or similar products, keep brightness
and contrast at a low level. Images with high level brightness or contrast may "burn on" the
screen permanently.
[Tips for cleaning the LCD TV]
1. Wipe the LCD TV with soft or dry cloth.
2. DO NOT use solvent or methyl benzene. Harsh chemicals may damage your LCD TV.
3. Make sure the LCD TV is unplugged before you clean it.
[CATV]
Be sure to acquire due authorization from the broadcaster/CATV service provider/program owner
before using the TV receiver to watch programs through UHF, VHF, or CATV.
[Installation and use of LCD TV]
1. Check the LCD TV power specification shown on the serial no./model tag. Be sure to use the
power according to the specification. If you are unsure about the power requirement, please
contact your distributor or local power company.
2. Make sure to plug into the poser cable into the socket securely. If you have problems plugging in,
please contact your distributor.
3. DO NOT overload power sockets or extension cords. Overloading poses a risk of electric shock or
fire.
4. DO NOT place any objects on the power cord. Keep your LCD TV away from any place that might
cause damage to the LCD TV. Use only the correct power cord.
5. Switch off your LCD TV when it is not in use If the LCD TV will not be in use for a long time,
unplug it to prevent the risk of fire.
6. The vent on the rear of the LCD TV is designed for ventilation and heat dissipation. Keep the vent
clear.
7. DO NOT place the LCD TV on beds, sofas, or carpet, as this may block the vent.
8. DO NOT place the LCD TV in enclosed spaces, such as a on a bookshelf or in a TV cabinet as
this may block the vent.
9. Keep the LCD TV away from high-temperature or heat-generating objects.
10. Keep the LCD TV away from direct sunlight.
11. DO NOT place the LCD TV on an unstable shelf or desk. Failing to do so may result in injury.
12. DO NOT allow foreign objects inside the LCD TV, as this poses a risk of electric shock or damage
to the internal components.
13. When transporting the LCD TV, do not carry it by holding onto the speakers. Be sure to always
carry the TV with two people holding it with both hands.
14. This equipment is for entertainment use only.
15.The device is not intended for use at visual display work places acc. BildscharbV.
............................................................................................................................................................. 03
Cautions
[Maintenance]
If any of following occurs, unplug the LCD TV and contact your distributor or appointed technician to
repair the LCD TV:
1. The power cord or plug is damaged.
2. Liquid enters the LCD TV.
3. LCD TV is damp or wet.
4. LCD TV is damaged.
5. LCD TV malfunctions.
DO NOT attempt to repair the LCD TV by yourself. There are high voltages inside the cabinet
which poses a risk of electric shock.
Changing parts
If the LCD TV requires new parts, ask for written proof of these required parts from the appointed
technician.
Safety inspection
After the LCD TV is repaired, remember to ask the technician to conduct a routine safety inspection
(based on the manufacturer’s requirements) to make sure the LCD TV is safe.
If the LCD TV has been used longer than its life, please contact qualified technician for repair.
[User's record]
You can find the serial no. and model tag on the back of the LCD TV. Do provide the serial no. when
you contacting the distributor or appointed service personnel.
Please read and comply with all warnings and instructions in the manual . Failing to do so may
void the warranty. Modifying the LCD TV in any unauthorised manner will void the warranty
immediately.
FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception which can be determined by turning the equipment off and on the user is
encouraged to try to correct the interference by one or more of the following measures:
* Reorient or relocate the receiving antenna
* Increase the separation between the equipment and receiver
* Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected
Caution: To comply with the limits for an FCC Class B computing device, always use the signal cord
and power cord supplied with this unit. The Federal Communications Commission warns that changes
or modifications to the unit not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
European Notice
Products with the CE Marking comply with both the EMC Directive (89/336/EEC), (93/68/EEC) and
the Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community.
4 ..................................................................................................................................................................
Cautions
■ Only use attachments/accessories specified by
the manufacturer.
■ Never modifiy arbitrarily any polarized or
grounding plugs designed for safety.If the plug
does not match your outlet, please contact the
electrical technician to replace your old outlet
with the one having new specification.
■ DO NOT place any objects on the power cord.
Keep your LCD TV away from any place that
might cause damage to the LCD TV. Use only
the correct power cord.
■ DO NOT overload power sockets or extension
cords. Overloading poses a risk of electric shock
or fire.
■ The device shall be installed away from the
surroundings with dripping or splashing water,
and no water-filling objects (e.g. vases) shall be
placed on the device.
............................................................................................................................................................... 5
r
Descriptions and accessories
LCD Panel
Speakers
1.Remote control 2.AAA battery X 2 3.User manual
Wall Mount Hole
Power Connecto
Support Hole：
Before operation, the auxiliary screw should be installed
on the stationary table. (Fig. 1)
For the safety, if TV could not be installed on the
stationary table, please fastens TV using two screws
through pulling thread between rear wall mounted holes
and wall additionally. (Fig. 2)
SCREW SIZE:T4x12
4.Power cord (USA, England or Europe) X1
For Europe:A VDE certified power supply cord
has to be used with this equipment for
Germany. The power cord rated 250V, 10A
minimum, according to IEC 60227, H05VV-F
or VW-1, 0.75 mm2 x 3G should be used.
Control panel
Power LED
IR Remote receiver
Video & Antenna
Connectors
PC & Video
Connectors
Support Hole
Installation of batteries
1. Insert two AAA batteries into the Remote control.
Make sure + and - are facing the proper direction.
2. Replace the cover.
If the remote control will not to be used for a long time, remove the batteries.
Use the remote control carefully. Do not drop the remote control on the floor.
Keep it away from moisture, direct sunlight, and high temperatures.
6 ..................................................................................................................................................................
LCD TV installation
AV and Antenna input Connection
Connectors and sockets
Port Functions
Scart 1
A connector for Europe, which uses the same connector to transmit AV,
SRGB, SV and Audio input signals; TV and Audio out signals.
A connector for Europe, which uses the same connector to transmit AV,
Scart 2
Tuner Input
AV R/L Audio
Output
............................................................................................................................................................... 7
SRGB and Audio input signals; by main screen(TV, AV, Scart1/AV/SV) and
Audio out signals.
Connects to TV RF signals (antenna/CATV).
Connect via audio cable for audio output.
LCD TV installation
Connectors and sockets
PC & Video Input Connection
Port Functions
The YPbPr video signal can be used if connecting through the component
Component Video
and R/L Audio input
VGA Input (analog)
and Audio input
HDMI Input (digital)
※ Support timing refer to spec table
video port. For example Progressive Scan DVD payers, Hi-scale HDTV
Decoders, and satellite receivers, obtain video with maximum resolution
using YPbPr and R/L audio signals.
Connect to VGA analog signals sources (※). PC audio supports 3.5mm
Jack.
High Definition Multimedia Interface
Connect to devices with digitals signals and can be used with PC or HDTV
video signals(※).
8 ..................................................................................................................................................................
LCD TV Installstion
Digital TV Connection
Connectors and sockets
Port Functions
SPDIF Connect to a Digital Audio component.
CA CARD SLOT CA card slot will be offer user insert a decryption card to this slot.
RF IN Connect to TV RF signals (antenna/CATV).
............................................................................................................................................................... 9
LCD TV installation Connectors and sockets
Power Connection
Attach the AC power cord to the LCD-TV and plug into an appropriate wall outlet.
Turn the power on at the main switch (Next to the power socket) to put the LCD TV into standby
mode. The standby indicator on the front will light up in red.
AC 100~240V
Power outlets differ from region to region.
Turning the LCD TV on
Press the POWER button on the front lower right of the TV to turn on the power or enter standby
mode.
Due to unstable local voltage, there will occasionally be a delay in POWER ON when the LCD
TV is switched on.
Power indicator Status
Green -- Power on
Red ---- Standby.
Power
Programming TV channels
1. Press the button on the remote control or on the control panel of LCD TV to select TV mode.
2. Press the button on the remote control to display the OSD menu
.
3. Press the
select frequency Scan.
4. Press the
(This will take a few minutes. The tuning process will find all available channels).
5. You can watch TV now. Change channels by pressing the P
button on the remote to highlight TV Setup and press the button to
button to start scanning : Auto Program Sort to start the tuning process.
and P buttons.
few minutes
10 ................................................................................................................................................................
LCD TV operation Control panel keys
Button Description
MENU
CHANNEL
(FUNCTIONS/T)
VOLUME +/ -
(ADJUST W/X)
Use this button to display and adjust the features in the On-Screen
Display(OSD). Use the four arrow keys (channel and volume adjustments)
to navigate the menu options.
Use these buttons to switch between preprogrammed channels.
In OSD mode,use those two bottoms to switch the selection up and down.
Use these two buttons to adjust the volume.
In OSD mode,use those two bottoms to switch the selection left and right.
SOURCE Use this button to change between video input signals.
Earphone Output Connect to headphones (16Ω or 32Ω).
..............................................................................................................................................................11
LCD TV operation Remote control functions
1. POWER
Press to turn on the LCD TV or enter standby mode.
2. MUTE
Press to toggle audio on and off. You can also press
volume +/- to restore the previous volume level.
3. ASPECT (screen scaling)
Change the aspect ratio. Choose from
Full / Zoom1 / Zoom2 / Auto / Original
4. PICTURE
Select advanced picture settings.
User / Vivid / Movie / Game / Sport
5. FREEZE
Press to freeze the picture. Press again to revert to
live viewing.
6. AUDIO
Select STEREO, MONO, DUAL 1 and DUAL 2.
If there is no second language available, the LCD
TV will select audio output as mono.
7. 0~9
Press 0~9 to select channels directly
8. RETURN
Return to the previous channel.
9. VOLUME +/-
Adjust the LCD TV volume.
10. PROGRAM
Select the Channel
11. SOURCE
Switche between signal sources.
a. Press the ”SOURCE” bottom you can see the
selection
TV / SCART1 / SCART2 / SCART1-S / YPbPr /
VGA / HDMI / DTV I
b. Use the ST keys to switch the slections
c. Press the ENTER / X bottom to confirm your
choice.
d. Press the MENU again to quit the picture.
12 ................................................................................................................................................................
LCD TV operation Remote control functions
12. INFORMATION (i)
Press the INFORMATION button to display the
current signal status, including input
source/channel/audio mode.
13. MENU STW X
Press MENU to activate the LCD TV OSD. Press
again to close the OSD. Press STW X to navigate
and confirm your selection.
TELETEXT----------------------------------------------------------
(Designed for Europe PAL/SECAM system only)
14. TEXT/MIX
Press this button to activate Teletext. Press again to
activate Teletext with TV .Press again to turn off
Teletext.
15. UPDATE
Enter the page number then press the
button and the teletext will display the page you
selected after searching. The page number is
displayed at the top side of screen.
16. INDEX
Press this button to return to page 100 or the index
page; and then press 0 to 9. The teletext page will
be numbered and added to the page you select or
the secondary item.
17. SUB
Display the sub page (when available).
18. PAGE UP& DOWN
Press this button then the number keys to select the
page you want view.
19. REVEAL
Reveal hidden information such as answers to a
quiz.
20. SIZE
Press this button to change the font size: Full screen,
Top half and Bottom half.
- FULL(full screen) standard full-screen text
- TOP(top half) top half of page appears on the
- BOTTOM(bottom half) bottom half of page appears on
21. HOLD
Press this button to stop the scrolling of pages.
The text decoder stops receiving data.
22. R/G/Y/B
Press this button to select the pictures with various
colors of text. Different channels display different
functions.
full screen
the full screen.
(UPDATE)
............................................................................................................................................................. 13
LCD TV operation Remote control functions
23. SLEEP
Sleep time setup function is unavailable in this
model.
24.PIP
PIP setup function is unavailable in this model.
Specical Keys for DVB/T -------------------------------------(Not available without DVB-T model)
25. EPG
Press this button to open the Programme Guide.
26. ENTER
Press this button to confirm choices in menus.
27. BACK
Press this button to clear on-screen information or
closes an open menu.
28. SUBTITLE
Press this button to open the Subtitles menu.
14 ................................................................................................................................................................
TV menu
1. Use the TV/VIDEO button on the remote control to select the required mode.
Once the signal source is detected, the selected system mode appears in the upper right corner of
the screen.
2. After the system mode is selected, press the buttons to perform the following functions:
Using the advanced menu
DISPLAY
Show more picture modes and functions based on your favorite channels and
enables you to adjust the color and brightness setup.
Enables you to configure advanced picture settings.
ADVANCED
Provide settings for further adjustment of color and brightness of the screen
based on the type of TV programs.
GEOMETRY (for use in PC mode)
Enable you to adjust the position and sharpness of the picture.
TV SETUP(for use with TV mode)
Enable you to adjust cable or antenna signal settings.
AUDIO
Provide more audio selections. You can also set the audio environment of the
LCD TV.
SYSTEM
Enable you to set the OSD language and OSD background.
............................................................................................................................................................. 15
TV menu
1. Press the MENU button on the side of the LCD TV or press the on the remote control.
2. Press the buttons to highlight the menu entries.
3. Press the
4. Press the buttons to highlight the item to be adjusted.
5. Press
6. Press the again to quit the picture
NOTE: Items in gray can not be selected and adjusted.
Display
button to enter the submenu.
to adjust the setting.
Using the advanced menu
Menu Descriptions
Contrast
Brightness
Saturation
Hue
Sharpness
Back Light
Press
Press
Press
Press
Press
Press the
to increase or decrease the picture contrast.
to make the picture brighter or darker.
to adjust color saturation.
to change the hue to make it redder or greener.
to make the picture sharper or softer.
buttons to make the BackLight brighter or darker.
Recall
Only available in some particular source modes.
*
16 ................................................................................................................................................................
Press
to restore all Display parameters to their default settings.
TV menu
ADVANCED
Menu Descriptions
Super Contrast
Skin Tone
Using the advanced menu
Press
※ PC(DVI, VGA) model does not support the function.
※ Opening Super Contrast function causing contrast modulates temporary at
running high frequency pattern that is normality.
Press
buttons to On/Off Dynamic Contrast Improvement.
buttons to increase skin tone.
GAMMA
Color Temp
Recall
Press
Press
Cool / Warm / Normal
Press
buttons to adjust color space.
to adjust the color temperature.3
to restore all Display parameters to their default settings.
............................................................................................................................................................. 17
TV menu
GEOMETRY (for VGA)
Using the advanced menu
Menu Descriptions
Auto
Clock
Phase
Automatic adjustment
Press the
Press the
display.
Press the
buttons to automatically adjust the picture setup.
buttons to adjust the VGA alignment for stable VGA
buttons to adjust the focus and sharpness of VGA.
in PC(VGA)/YPbPr model, if the picture quality fails to meet your maximum
expectation when “Auto” is pressed, please adjust the “Phase” function to do
manual calibration for refining picture quality.
H-Position
V-Position
Recall
Either in PC(VGA)/ YPbPr model, if the picture quality fails to meet your maximum expectation when
“Auto” is pressed, please adjust the “Phase” function to do manual calibration for refining picture qualit
Press the
Press the
Press
buttons to adjust the horizontal VGA position.
buttons to adjust the vertical VGA position.
to restore all Display parameters to their default settings.
18 ................................................................................................................................................................
TV menu
TV SETUP (for TV)
Using the advanced menu
Menu Descriptions
Region Selection
Frequency Scan
Update Scan
Program Edit
Press the
To search the local channel automatically,you can execute the auto
program(APS)function
Press the ENTER button to execute automatic channel scanning. Automatic
channel scanning must be executed when you install your LCD TV for the first
time.
Use Scan Update function can scan the programs again after APS and
keeps the program list arrangement as you designed before,
program lists after the existing program table.
Use Manual Search function can fine tuning the programs again after
APS and keeps the program.
buttons to select your country.
the additional
............................................................................................................................................................. 19
y
TV menu
Program Edit (for TV)
Channel Table:
After running the Auto Program Sort function to load the local program list. You can use the color keys
on remote control to edit your personal program list.
Insert
Using the advanced menu
Use the
Then press the red key on remote control to enter the “Insert” function.
Move the highlight bar to the location you would like to insert the selected program, the press the red
key again to confirm.
Swap
Use the
Then press the green key on remote control to confirm the selection.
Move the highlight bar to another program which you would like to swap with, then press the green
key again to confirm.
Those two programs will swap the location on the list.
Delete :
Use the
Press the yellow key on remote control twice to delete the program.
Copy :
Use the
Then press the blue key on remote control to enter the “ Copy” function.
Move the highlight bar to the location you would like to locate the copy on the list, then press the red
key again to confirm.
The copied item will add on the expected location.
buttons on remote control to select the program you want on list.
buttons on remote control to select the program you want on list.
buttons on remote control to select the program you want on list.
buttons on remote control to select the program you want on list.
Red / Green / Yellow / Blue ke
20 ................................................................................................................................................................
TV menu
Tuning Table:
Using the advanced menu
ID : Use the
Use the keys to edit ,Press the "MENU" button to confirm the setting.
Press the
cycle through A,B,C…a,b.c…0,1,2,3…then _,@,#"$..., etc.
FREQ : Use the
Use the keys to edit ,Press the "MENU" button to confirm the setting.
Press the
Manually adjust the frequency for variation of each channels to get a better image quality,
but it will be fixed the frequency after adjustment unless re-update scan.
SYSTEM : Use the
Use the keys to edit ,Press the "MENU" button to confirm the setting.
Use the
If you live in an area which can receive different TV systems you may choose to change
the default system to the system used in your area.
into ID edit channel name
buttons to select your required letters:
into FREQ edit channel frequency
buttons to select your required letters:
into SYSTEM edit channel system
buttons to choose which TV system to represent the screen.
SKIP : Use the
Use the keys to edit ,Press the "MENU" button to confirm the setting.
Press the
............................................................................................................................................................. 21
into SKIP edit channel skip on/off
buttons to select.
TV menu
AUDIO
Menu Descriptions
Bass
Treble
Balance
Using the advanced menu
Press the
Press the
Press the
speakers.
buttons to increase or decrease the audio bass level.
buttons to increase or decrease the audio treble level.
buttons to adjust the balance between right and left
Press
HDMI Audio
Reset
Only available in some particular source modes
*
.
In general use, LCD Monitor connected DVD or others Player, please select
Digital Mode; when LCD Monitor connected Computer (DVI/HDCP), please
select Analog mode. (This setting perform under HDMI mode)
Press
button to select Digital or Analog Mode for input HDMI Audio.
to restore all Display parameters to their default settings.
22 ................................................................................................................................................................
TV menu
SYSTEM
Menu Descriptions
Language
OSD Background
Recall Press to return all system parameters to their default settings.
Using the advanced menu
Press the
Press
buttons to select language.
buttons to select OSD background is opaque or transparent.
............................................................................................................................................................. 23
Digital TV menu
Digital OSD Functions
This product has Digital TV of UK/Pan Europe DVB-T, The use Pay Per View services. For details,
refer to the instruction manual supplied with your CAM.
The following is Digital TV OSD menu. And if you don’t know how to use all OSD function, you can
press i button in Remote control for more detail instruction.
First-Time Installation
When the system is first switched on, the Reference Application attempts to configure itself for the
first time. This is called First Time Installation.
The user is then asked if they wish to perform an automatic tune for services. Automatic tuning
functionality is described later in this document. When the automatic tune finishes and services have
been found, the lowest number service is selected and a banner describing that service is shown. A
user may have chosen not to perform an automatic tune or no services may have been found by an
automatic scan. In this instance the user may use the Main Menu to automatically scan again or
perform a manual scan. The Reference Application also provides the facility for the user to force to
trigger a First Time Installation.
This facility can be found in the Main Menu under the Installation option.
Digital OSD Functions
24 ................................................................................................................................................................
Digital TV menu
Main Menu
Main Menu
Main Menu is provided to enable the user to configure elements of the Reference Application.
In normal viewing operation a user can access the Main Menu by pressing the DTV MENU key.
The Main Menu is hierarchically organized into categories in order to fit on the screen.
1.Channel List
A user may configure the Reference Application to use exclusively TV, Radio or Data services,
this feature is know as channel List Model.
A user can select a channel List Mode using the configuration dialog, it is permitted to select a
channel List Mode that contains no services.
When the channel list mode is enabled the program up and down buttons on the remote control
will only select those services in the current channel List Mode. And all EPGs will only show those
services in the current Channel List Mode. It is still possible to select a service using the service’s
even if it is not a member of the currently selected channel List Mode. Note that if the user has
selected a favourites list then the Channel List Mode acts as a filter on top of the selected
favourites list.
Please press the button on your remote control to tune to the highlighted channel.
Press to exit this screen.
2.Edit Favourites Lists
A favourites list enables the user to select a subset of services they consider favourite.
The Reference Application allows the user to have up to five different favourites lists.
Favourites lists are defined in the favourites dialog that can be accessed by selecting the favourites
button on the channel list dialog and via the Main Menu. Press the button on your remote
control to add the channel to the highlighted favourites list. An icon indicates which favourites list a
channel is in.
............................................................................................................................................................. 25
............................................................................................................................................................. 25
Digital TV menu
3.Guides
Main Menu
Now/Next EPG
An EPG dialog is provided that allows the user to view the current and next programme playing on
each service.
In this dialog a list of channels and the corresponding current and next programmes is displayed.
The user can navigate up and down the list of channels and highlight either the now or next
programme. Information for the highlighted programmes can be displayed by pressing “Info”. This
information includes the start/end time of the programme, the programme genre in brackets, and a
synopsis of the programme content.
A user may select a service by highlighting a program in the ‘now” list and pressing the key.
Pressing the
the EPG.
The Now/Next Electronic Program Guide cannot be accessed if there are no services available.
List schedule EPG
User can set up Program schedule list.
Time Line Schedule EPG Extended Schedule EPG information is presented using a list format,
either on a banner for the current service, or as a full screen dialog showing multiple services.
4.Settings
key the user may select a genre to highlight events with the selected genre in
4-1 Configuration
Time Zone: Press
(Inc.GMT/CET)
DST
Press
Subtitle
Press
Banner
1/2/4/8/OFF seconds.
Favorite Mode
Press
remember that at least one favourite channel be selected before turning favourites on.
26 ................................................................................................................................................................
to select or deselect DST mode, Press to exit this screen.
to select subtitle On or Off, Press to exit this screen.
then select to choose favourite mode. Press to exit this screen. Please
to select the time zone you are in.Press to exit this screen.
Digital TV menu
Channel List
Press
only, Radio only and Text only, Press to exit this screen.
Parental Settings
Press to enter the parental lock menu. Press to exit this screen.
If you don’t know how to use above function, you can select i info button in remote control for get
information, press i info button again will exit.
4-2 Language Settings
System
To change the system languages, this changes the language used in all menus and dialogs.
Noted
Pan Europe system language include: English, German, French, Italian, Spanish, Danish,
Norwegian, Swedish, Finnish, Portuguese, Polish and Dutch. UK system language include:
English, Welsh and Gaelic.
Audio
Displays a dialog enabling the preferred language to be set, this is the language to be used for all
channels if it is available.
Subtitle
Displays a dialog enabling the preferred language to be set, this is the language to be used for all
channels if it is available.
Current
Displays a dialog enabling the current language to be set, this is the language to be used for the
current selected channel, please note that only languages available with the currently selected
channel will be displayed.
Main Menu
then select to choose channel list mode, you can select show all channel, TV
............................................................................................................................................................. 27
Digital TV menu
4-2 Installation
Main Menu
PAL PAL PAL PAL PAL PAL PAL PAL PAL
4-2.1 Automatic Search
Automatic search is the ability for the reference application to scan each other (Frequency) for
services. Whilst performing an automatic tune no service will be selected. A dialog is displayed
during automatic tuning that shows the progress of the scan through the channels. Automatic
tuning may be cancelled by the user. If the previous list already stored, the lowest number from
the service list, it will return to “normal viewing” operation. The Reference Application can
support up to 70 services at any one time. When you select Automatic search, press OK button
in remote control, and will start to automatic search.
4-2.2 Manual Search
Manual search allows the user to scan an individual channel (frequency) for services .The user
can perform a manual tune by selecting an option on the “Main Menu”. Whilst performing a
manual tune no service will be selected. The user enters the channel number to be scanned;
only those channels supported by the tuner may be entered. The Manual tuning dialog
displays a bar indicating the quality and Signal level of the signal of the currently selected
channel. The user can then choose to scan the selected channel for services; a separate dialog
28 ................................................................................................................................................................
Digital TV menu
is displayed showing the service found whilst scanning is taking place. Newly discovered
services are merged with the current list of services. Manual tuning may be cancelled by the
user, in such cases any newly discovered services are disregarded. When a manual tune is
complete the application will attempt to select the previously selected service and return to
“normal viewing” operation. In cases were there was not a previously selected service the
application will attempt to select the service with the lowest number. The Reference
Application can support up to 70 services at any one time. Press 0 to 9 to select a channel
number, select to start searching for channels,
4-2.3 First time installation
Choose this will return to the original condition, you can choose country as first time in
installation. And search channel again. When you select it, you will see as following:
5.Common Interface
If no CA module is inserted, then the system display “No common interface mode detected”.
If a CA module without a smartcard is inserted. Then the system displays “Please insert your
smartcard”.
If a CA module with a smartcard is inserted. Then the CI menu is displayed .Using this menu. The
user can read the smartcard contents. The data shown depends on CA vendor and CA smartcard
version.
Main Menu
to exit this screen.
............................................................................................................................................................. 29
Other Information Trouble-shooting
The following table contains the common problems and the solutions to these problems.
Please check this list before you contact technicians.
PAL PAL PAL PAL PAL PAL PAL PAL PAL
Problems Reasons Solutions
No picture 1. Did you connect the power cord ?
2. Did you turn on the power ?
3. Is the signal cable connected
correctly ?
4. Is the screen in energy-saving
mode ?
Abnormal colors 1. Is signal cable connected
correctly ?
Twisted picture 1. Is the signal cable connected
correctly ?
2. Is input signal of compatible
frequency ?
Picture too dark 1. Are brightness and contrast set at
the lowest level ?
Audio only, no
images
Picture only, no
audio
Cannot use remote
control
The following table contains common problems and solutions to these problems.
Problems Possible solutions
Cannot receive sufficient
channels through antenna
No colors Please adjust the color setup
Blinking picture
accompanied by ghost
image
Broken lines or segments Adjust antenna
Certain TV channels are
blocked (Hope to acquire
some channels)
Overlapping images or
ghost images
Cannot use a function If the item you choose turns gray, that item cannot be selected.
Cannot receive programs Please use the automatic scanning method to add the channels not
If you have further questions after reading the above descriptions, please contact your distributor.
1. Is input signal connected
correctly ?
2. Is TV signal too weak ?
1. Is signal cable connected
correctly ?
2. Is volume at the minimum level ?
3. Is audio signal cable not
connected ?
4. Is TV signal too weak ?
1. Is the battery dead?
2. Is there any disturbance from static
or thunder ?
Please use the automatic scanning function to increase the number
of channels not included in memory (Please refer to page 19)
Check the connection of antenna/signal cable.
Check if channel is in play mode
Press signal source and change input mode
Keep the TV away from noise sources, such as automobiles, neon
lights, and hair dryers
Please use the automatic scanning method to add the channels not
included in memory (Please check page 19)
Please use multi-directional outdoor antenna
(If your TV is subject to the influence of nearby mountains or
buildings)
included in memory (Please check page 19)
1. Connect power cord correctly.
2. Turn on power.
3. Connect signal cable correctly
4. Press any button on the computer.
1. Connect signal cable correctly.
1. Connect signal cable correctly.
2. Please use compatible signal.
1. Adjust brightness and contrast.
1. Please check if input signal is
connected correctly.
2. TV-RF signal must not be lower
than 50dB.
1. Connect signal cable correctly.
2. Adjust volume to proper level.
3. Connect audio signal cable
correctly.
4. TV-RF signal must not be lower
than 50dB.
1. Please change battery.
2. Turn off power for 10 seconds;
and then restart power.
30 ................................................................................................................................................................
Other information Specifications 32” LCD TV
Active Area / Screen Size 32” TFT LCD
Display panel
Compatibility
Power
Other Built-in speaker
Aspect Ratio Widescreen 16:9
Max. of Pixels 1366(H) X 768(V)
VGA 640X480 @60, 72, 75Hz
PC
HDMI+HDCP
SDTV/HDTV scanning format 480i / 480p / 576i / 576p / 720p / 1080i
Input Voltage AC100-240V, 2.4A, 50/60Hz
Operation <180 W (Max)
Standby <1 W
Operating 5 –35°C (41~95°F) / 10%~90% (no condensation) Environment
Storage temperature -20 – 60°C (-4~140°F) / 10 %~90 % (no condensation)
720X400 @70Hz
SVGA 800X600 @60, 72 ,75Hz
XGA 1024X768 @60, 70, 75Hz
WXGA 1360X768 @60Hz
VGA 640X480 @60Hz
SVGA 800X600 @60Hz
XGA 1024X768 @60Hz
WXGA 1360X768 @60Hz
8Ω, 10W, x2 (Max)
............................................................................................................................................................. 31
32 ................................................................................................................................................................
Loading...