Mirabelle BRADENTON, MIRBD200, MIRBD240, MIRBD250, MIRBD230 Installation Instructions Manual

WARRANTY

WHAT IS COVERED?

Wolseley North America “Wolseley” or the “Company” warrants its products to be free from defects in material and workmanship under normal use and service FOR A PERIOD OF ONE (1) YEAR FROM THE DATE OF INSTALLATION.

WHAT IS NOT COVERED?

The warranty set forth in paragraph 1 does not cover installation or any other labor charges and does not apply to products which have been damaged as a result of any accident, abuse, improper installation or maintenance, or modiﬁcation of original plumbing product. The warranty of such products is limited to the warranty extended to Wolseley by the product manufacturer. Finally, WOLSELEY NORTH AMERICA SHALL NOT BE RESPONSIBLE OR LIABLE FOR ANY FAILURE OR DAMAGE TO THIS PRODUCT OR ANY COMPONENT THEREOF CAUSED BY THE USE OF ABRASIVE CLEANERS.

HOW TO OBTAIN WARRANTY SERVICE

The purchaser should contact their local Wolseley location, installing contractor or builder from whom the product was purchased or upon written request addressed to Wolseley North America 12500 Jefferson

Avenue, Newport News, VA 23602, Attention Consumer Affairs. Any shipping charges, associated with warranty service, must be prepared by the consumer. In all cases, proof of purchase will be required. LIMITATIONS OF IMPLIED WARRANTY AND DISCLAIMER OF CONSEQUENTIAL OR INCIDENTAL DAMAGES WOLSELEY NORTH AMERICA DISCLAIMS ANY LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES AND DISCLAIMS ALL EXPRESS OR IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, AS SET FORTH ABOVE. IMPLIED WARRANTIES OF THE PRODUCTS AND PRODUCT COMPONENTS SET FORTH IN PARAGRAPH 1 ABOVE ARE LIMITED TO THE DURATIONS OF THE RESPECTIVE WARRANTY. Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above limitations may not apply to you. This warranty gives you speciﬁc legal rights and you may also have other rights, which vary from state to state.

TWO-PIECE WATER CLOSET

INSTALLATION INSTRUCTIONS

FOR BRADENTON SERIES

MIRBD200 MIRBD230 MIRBD240 MIRBD250

THANK YOU FOR CHOOSING MIRABELLE

Thank you for selecting Mirabelle. We appreciate your commitment to Mirabelle quality.

To insure that your installation proceeds smoothly, please read these instructions before you

begin. Carefully unpack and examine all of the package contents.

Thanks again for choosing Mirabelle.

ALL INSTALLATION PROCEDURES MUST COMPLY IN STRICT ACCORDANCE

WITH APPLICABLE LOCAL PLUMBING AND BUILDING CODES.

BEFORE YOU BEGIN

1. REMOVE THE EXISTING TOILET

BEFORE YOU BEGIN 1. REMOVING THE ExISTING TOILET

• Carefully inspect the new toilet for damage.

• If the existing toilet does not have a supply

shut-off valve below the tank, install one

before installing the new toilet.

TOOLS AND MATERIALS

CAUTION

Risk of personal injury or

product damage.

Handle with care. Vitreous china can break

or chip if the product is handled carelessly.

• Turn off water supply.

• Flush toilet, then sponge out all remaining

water from the tank.

Old wax seal

Flange

• Remove old wax seal from ﬂoor with

• Remove old wax seal from floor with

a putty knife.

5/16” Diameter bolts

Putty knife

10 “ Adjustable wrench

Supply shut-off valve

Tape measure

Level

Sponge

Wax seal

5/16” Bolts w/nuts and

washers

Putty knife

1/2” Nut driver/socket

Hacksaw

Screwdriver

• Disconnect supply shut-off valve (if present),

and remove old tank and bowl.

CAUTION

Risk of hazardous gases.

If the new toilet is not installed immediately,

temporarily stuff a rag in the closet flange.

Flange

• Replace old bolts with the new 5/16”

diameter bolts.

3. INSTALL THE TANK

2. INSTALL THE NEW TOILET

2. INSTALL THE NEW TOILET 3. INSTALL THE TANK

• Install or relocate the supply and outlet as

necessary to conform to the roughing-in

dimensions.

• Install a supply shut-off valve.

• Lay the toilet down onto a padded surface.

Bottom of bowl

Wax seal

Bolt Cap

Nut

Washer

Bolt Cap Base

Bolt

• Place bolt cap bases over bolt.

• Place metal washers and nuts on plastic bolt

cap bases and bolts.

Bolt

Tank to bowl gasket

Locknut

Bolt

Rubber washer Metal washer Nut

Bolt Rubber washer

Rubber washe Metal washer

Nut

• Carefully inspect the new toilet for damage.

• From the bottom of toilet, firmly press a new wax seal around toilet outlet.

• If the existing toilet does not have a supply shut-off valve below the tank, install one

• Remove temporary rag (if used) from

before installing the new toilet.

toilet flange hole.

Closet flange

• Align and lower toilet over ﬂange and bolts.

• Align and lower toilet over flange and bolts.

• Apply your full body weight around the

• Apply your full body weight around the toilet

toilet to set seal

to set seal

Bolt

CAUTION

Risk of external leakage.

Do not lift or rock the bowl after

placement. If you break the watertight

seal, you must install a new wax seal.

• Carefully tighten nuts.

CAUTION

Risk of product damage.

Overtightening may cause breakage or

chipping of vitreous china.

Bolt

Hacksaw

• If bolts extend more than 1/4” (6 mm) over

top of the nuts, cut off excess.

CAUTION

Risk of product damage.

Protect the vitreous china from exposure

to the saw blade when cutting off

excess bolt length.

• Attached bolt caps.

• Attach bolt caps.

• Carefully inspect the new toilet for damage.

• Place the tank-to-bowl gasket onto the locknut on the flush valve shank against

• If the existing toilet does not have a supply

the bottom of the tank (Be sure locknut

shut-off valve below the tank, install one

is tight).

before installing the new toilet.

Locknut

Gasket

Bowl inlet

• Position tank on bowl by centering gasket

on bowl inlet.

• Insert bolts through holes inside tank and

down through holes in bowl making sure

down through holes in the bowl making

tank is level.

sure tank is level.

Rubber washer Metal washer Nut

• Assemble washers and nuts to tank bolts.

Alternately tighten nuts so that tank stays

level.

CAUTION

Risk of product damage.

Overtightening may cause breakage or

chipping of vitreous china.

• Be sure suts are tight enough to achieve a

• Be sure nuts are tight enough to achieve a

watertight seal. Do not overtighten.

4. COMPLETE THE INSTALLATION

IMPORTANT CONSUMER INFORMATION

4. COMPLETE THE INSTALLATION

IMPORTANT CONSUMERR INFORMATION

Cap

Trip lever

Fill valve

Washer

Filter screen

• Install trip lever. Follow instructions packed with the trip lever.

Tank

Fill valve nut

Supply shank

Seal washer

Tubing

Coupling nut

Nut

Hose

Locknut

Clip

Nut

Comp. washer

Tubing

Coupling nut

Compression nut

Ferrule

Flush valve

Waterline

Flapper

Seal

• Open supply shut-off valve slowly to check

for leaks. If the connections have been

properly assembled, a slight tightening of

the nuts should stop any leakage.

• Install toilet seat according to the packed

instructions.

Adjust water level

Waterline

Filter screen

• Adjust tank water level to the proper

marked waterline by rotating threaded rod

clockwise to raise water level or

counterclockwise to lower water level.

Remove tape before flushin

Attention Installer:

Recommended water pressure is 20 psi.

Care and Cleaning

Clean the outside surface of your vitreous

china water closet with mild soap and warm

water. Wipe the entire surface completely dry

with a clean soft cloth. You may use soft

abrasive cleaners when necessary to clean

your water closet.

CAUTION

Risk of product damage.

DO NOT use strong abrasive cleaners, as

they will scratch and dull the surface.

Wipe any splashes of cleaning solutions from

plastic or plated surfaces immediately. Use

water closet cleaners on the inside of the bowl

only.

If the vitreous china surface becomes

excessively dirty, use a general purpose

cleaner such as: Fantastic, Basin Tub and Tile

Cleaner, Soft Scrub, Disinfectant Bathroom

Cleaner, Spic and Span Liquid, Scrubbing

Bubbles, or Bon Ami. Over time, hard water

deposits may clog water closet rim bowl rinse

holes and trapways. To clean, use a

commercial cleaner that is recommended for

removing hard water deposits. Follow the

cleaner manufacturer’s instructions for use.

WARNING

Risk of property or product damage.

DO NOT use in-tank cleaners in your

water closet. Products containing chlorine

(calcium hypochlorite) can seriously

damage fittings in the tank. This damage

can cause leakage and property damage.

Mirabelle shall not be responsible or liable

for any tank ﬁtting damage caused by the use

for any tank fitting damage caused by the use

of cleaners containing chlorine (calcium

hypochlorite).

Compression nut

Ferrule

• Connect supply shut-off valve to toilet

supply shank.

• Flush toilet several times and check all

connections for leaks.

Supply shut-off valve

5. CONFIRM OPERATION

• Carefully set cover onto tank.

• Periodically check for leaks for several days

following the installation.

5 6

+ 8 hidden pages

Mirabelle BRADENTON, MIRBD200, MIRBD240, MIRBD250, MIRBD230 Installation Instructions Manual

Specifications and Main Features

Frequently Asked Questions

User Manual