Page 1
360m
360r
360i
MIRA 360m SHOWERHEAD
MIRA 360r SHOWERHEAD
MIRA 360i SHOWERHEAD
INSTALLATION & USER GUIDE
These instructions must be left with the user.
1
Page 2
2
INTRODUCTION
Introduction
Thank you for purchasing a quality Mira product. To
enjoy the full potential of your new product, please
take time to read this guide thoroughly, having
done so, keep it handy for future reference.
Mira showerh eads are desig ne d to give a
satisfactory shower over a range of pressures.
These showerheads are suitable for pressures
between 0.1 and 5.0 bar.
General
1. Insta l l a t ions m u s t co m p l y wi t h Wa t e r
Regu latio ns (Bye-L aws, Scotla nd), and
any other Local Regulations and Building
Reg u l a t i ons i n f o r c e a t the t i me o f
installation.
2. Before installation carefully inspect the product
for any signs of damage.
Guarantee
For domestic installations, Mira Showers
guarantee the products listed in this guide against
any defect in materials or workmanship for a
period of one year from the date of purchase.
For terms and conditions refer to the back cover
of this guide.
Patents and Design Registration
Patent Applications:
UK: 0715612.8, 0804172.5
World: PCT/GB2008/002703
Design Registration:
Europe: 001004022
If you experience any difficulty with the
ins t a l l a t i o n or op e r a t i o n of yo u r n e w
showerhead, please refer to ‘Fault Diagnosis’,
before contacting Kohler Mira Ltd. Our contact
details can be found on the back cover of
this guide.
FLOW RATES
The ow rates for the Mira 360 showerheads are
listed below.
Spray Pattern Inlet Pressure
0.5 bar
Rain 12.3 l/min 5.4 l/min
Storm 11.5 l/min 5 l/min
Burst 7 l/min 3.3 l/min
Cloud 4.2 l/min
Cloud LC 2.7 l/min
Inlet Pressure
0.1 bar
USER MAINTENANCE
If you require a Mira trained service engineer or
agent, refer to section: ‘Customer Services’.
Fault Diagnosis
Symptom:
Sprayplate assembly blocked.•
Cause / Rectication:
Clean the sprayplate.•
—————————————
Symptom:
Drip from sprayplate assembly.•
Cause / Rectication:
A small amount of water may be retained •
in the showerhead after the shower control
has been turned off. This may drain over
a few minutes. Changing the angle of the
showerhead may vary the draining time.
—————————————
Symptom:
Poor spray pattern from the Cloud sprayplate •
assembly.
Cause / Rectication:
Change the Cloud sprayplate assembly for •
the LC (Low Capacity) version.
Caution! The LC sprayplate must not be used
on electric showers
—————————————
Page 3
3
OPERATION
4
5
1
2
6
3
7
8
Turn the showerhead in the direction shown to activate the different spray patterns.
Cloud Burst
Rain
Storm
Page 4
4
Cleaning
Many household cleaners contain abrasives and
chemical substances, and should not be used for
cleaning plated or plastic ttings.
These nishes should be cleaned with a mild
washing up detergent or soap solution, and then
wiped dry using a soft cloth.
Use your thumb or a soft cloth to wipe any
limescale from the soft nozzles and the front
surface of the showerhead sprayplate.
Important! The sprayplate must be regularly
cleaned to make sure that the showerhead does
not become blocked.
Spray Plate Assembly
1. Use a suitable tool to remove the grommets.
2. Using the 2.5 mm hexagonal wrench (supplied),
remove the screws.
3. Separate the sprayplate assembly into its
individual components.
4. Clean or replace components as necessary.
Note! Make sure that the seals are located
correctly.
5. Re as se mb le the components in reverse
order.
Grommet
Screws
Seals
Use your thumb or a soft cloth
to wipe any limescale from the
soft nozzles
Cleaning the Sprayplate Assembly
Seals
Replacing the Sprayplate or Seals
Page 5
5
Cloud Spray Plate Assembly
This pro duct is supplie d configured for the
majority of showering systems including electric
showers.
Note! for showers with a pressure of below 0.15
bar (1.5 metre head) it might be necessary to
change the Cloud sprayplate assembly for the
LC (Low Capacity) version in order to achieve a
suitable spray pattern.
Caution! The LC sprayplate must not be used
on electric showers
1. Use a suitable tool to remove the grommets.
2. Using the 2.5 mm hexagonal wrench (supplied),
remove the screws.
3. Separate the sprayplate assembly into its
individual components.
4. Replace the Cloud assembly sprayplate with
the LC version.
5. Re as se mb le the components in reverse
order.
Grommet
Seals
Screws
ACCESSORIES
Flow Regulator (12 L/min - Red) - 1641.059
If your shower has no flow control, you may
nd operation of the shower on high pressure
systems too forceful. Fitting a ow regulator in
the showerhead will reduce this.
Checkvalve (360m and 360r) - 1688.282
Seals
Low Capacity
Sprayplate
Replacing the Cloud Sprayplate Assembly
Checkvalve (360i) - 1688.283
To comply with UK Water Regulations you must
make provision to prevent the backow of waste
water through the shower.
A hose retaining ring will allow compliance but
may restrict full use of the hose.
However, if your mixer shower is already tted
with single inlet checkvalves then tting the extra
showerhead checkvalve will allow compliance
without the need for the hose retaining ring.
Page 6
6
SPARE PARTS
Spare part numbers are indicated in bold and are available from authorised stockists or merchants
(locations on request) or direct from Mira Customer Services, our contact details can be found on the
back cover of this guide.
575.12 Hexagonal Wrench - 2.5 mm (not illustrated)
1688.160 Rain Assembly - white
1688.161 Rain Assembly - black
1688.162 Storm Assembly - white
1688.163 Storm Assembly - black
1688.164 Cloud Assembly - white
1688.165 Cloud Assembly - black
1688.166 Burst Assembly - white
1688.167 Burst Assembly - black
1688.168 Seal & Screw Pack - components identied ‘A’
1688.184 Seal & Screw Pack - black - components identied ‘B’
1688.169 360i Handle
1688.200 360m Showerhead - chrome/white
1688.201 360m Showerhead - chrome/black
1688.202 360r Showerhead - chrome/white
1688.203 360r Showerhead - white
1688.204 360i Showerhead - chrome/black
1688.275 Cloud Assembly LC (Low Capacity) - white
1688.276 Cloud Assembly LC (Low Capacity) - black
360m
1688.162
A, B
1688.163
1688.200
1688.201
1688.164
1688.165
1688.275
1688.276
A, B
1688.166
1688.167
A, B
1688.160
1688.161
Page 7
7
360r
1688.162
A
1688.166
1688.202
1688.203
360i
1688.204
1688.164
1688.275
B
1688.165
1688.276
A
A
1688.160
1688.163
1688.167
B
1688.169
B
1688.161
Page 8
Guarantee of Quality
Mira Showers guarantee your product against any defect
in materials or workmanship, provided that it is installed
and maintained in accordance with the instructions given
in this guide.
To validate the guarantee, please return your completed
registration card within 30 days of product installation.
Within the guarantee period we will resolve defects, free
of charge, by repairing or replacing parts or modules as
we may choose.
To be free of charge, service work must only be undertaken
by Mira Showers or our approved agents.
Service under this guarantee does not affect the expiry
date of the guarantee.
The guarantee on any exchanged parts or product ends
when the normal product guarantee period expires.
Not covered by this guarantee:
Planned maintenance, or replacement parts required to
comply with the servicing requirements of the TMV 2 and
TMV 3 healthcare schemes (where applicable).
Damage or defects arising from incorrect installation,
improper use or lack of maintenance, including build-up
of limescale.
Damage or defects if the product is taken apart, repaired or
modifi ed by any persons not authorised by Mira Showers
or our approved agents.
This guarantee is in addition to your statutory and other
legal rights.
What to do if something goes wrong
If when you first use your shower, it doesn’t function
correctly, fi rst contact your installer to check that installation
and commissioning are satisfactory and in accordance with
the instructions in this manual. We are on hand to offer you
or your installer any advice you may need.
Should this not resolve the diffi culty, simply contact our
Customer Services Team who will give every assistance
and, if necessary, arrange for our service engineer to
visit. If the performance of your shower declines, consult
this manual to see whether simple home maintenance is
required. Please call our Customer Services Team to talk
the diffi culty through, request a service under guarantee
if applicable, or take advantage of our comprehensive
After-Sales service.
As part of our quality and training programme calls may be
recorded or monitored.
Our Customer Services Team is comprehensively trained to
provide every assistance you may need: help and advice,
spare parts or a service visit.
Spare Parts
We maintain an extensive stock of spares and aim to provide
support throughout the product’s expected life.
Genuine Mira spares c an be purchased direct from
Customer Services or from approved stockists or merchants
(locations on request).
Spare parts will normally be despatched within two working
days. Payment can be made using
most major Credit or
Debit cards at the time of ordering. Should payment by
cheque be preferred, a pro-forma invoice will be sent.
All spares are guaranteed for 12 months from the date of
purchase. Spares that have been supplied directly from
us can be returned within one month from the date of
purchase, providing that they are in good order and the
packaging is unopened.
Note! Returned spares will be subject to a 15% restocking
charge and authorisation must be obtained before return.
Please contact our Customer Services Team.
Note! In the interests of safety, spares requiring exposure
to mains voltages s hould only be fitted by competent
persons.
Service / Repairs
Our Service Force is available to provide a quality service
at a reasonable cost. You will have the assurance of a Mira
trained engineer/agent, genuine Mira spare parts and a
12 month guarantee on the repair.
Payment should be made directly to the engineer/agent who
will accept most major Credit or Debit cards or a cheque
supported by a banker’s card.
To Contact Us
England, Scotland, Wales and Northern Ireland
Mira Showers Customer Services
Telephone: 0870 241 0888, Mon to Fri 8:00 am - 5:30 pm
Sat 8:30 am - 3:30 pm
E-mail: technical@mirashowers.com
Fax: 01242 282595
By Post: Cromwell Road, Cheltenham,
Gloucestershire, GL52 5EP
Eire
Modern Plant Ltd (Dublin)
Telephone: 01 459 1344, Mon to Fri 9:00 am - 5:00 pm
E-mail: sales@modernplant.ie
Fax: Dublin 01 459 2329
Post: Otter House, Naas Road,
Clondalkin, Dublin 22
Mira is a registered trade mark of
Kohler Mira Limited.
The company reserves the right to alter
product specifi cations without notice.
www.mirashowers.co.uk
5
+
!
3
CUSTOMER SERVICE
1106063-W2-A © Kohler Mira Limited, December 2008
8
Loading...