Minuteman SSL-WATER User Manual

r

r

A

y

r

A

j

A

f

y

A

f

r

f

SSL-WATER User’s Manual

IMPORTANT: Read all of the instructions before
attempting to install the SSL-WATER leak sensor.

DESCRIPTION

The SSL-WATER sensor is a device, which connects with
SSL-EMD. When water permeates into the sensor cable, the
conductivity enhances the intensity of electric current and the
alarm will be triggered. Through the SNMP-SSL card, the use
can monitor it and receive notifications of the alarms. The
following cable type comes with the water leak sensor:

• Type A: 1m water leak sensor connected to 1.2m cable

APPLICATION

Common usage are areas where mission-critical equipment is
being maintained, including data rooms, data centers, clean
rooms, utility corridors, laboratories, telecommunication
facilities, storage areas, elevator shafts, drip pans unde
water-cooled equipment, and many more. The most common
application for water leak detection is under raised floors. It is
common for water leak sensors to be installed under the
raised floor as well as in the ceiling above equipment.
Facilities and equipment that use water-cooled technology
have started to add water leak sensors to provide early
warning of water leaks. The water leak sensor is installed
around the supply and return water lines.

INSTALLATION

1. Loosen the screws on SSL-EMD.

2. Connect the wires of SSL-WATER sensor to the SSL-EMD
larm-1 and/or Alarm-2, and then tighten the screws.

3. Connect the straight-through CAT5 network cable from the

SNMP-SSL card’s RJ45 connector labeled “COM” to the
connector labeled “010101” on the SSL-EMD.

4. Verify that the SNMP-SSL card has a network connection and

is powered on.

5. Check the LED (Power/Status) of SSL-EMD, it will flash ever

5-seconds.

6. Open a Web browser and connect to the SNMP-SSL card.

7. Change the setting of “SSL-EMD Status” from “Disable” to

“Auto” on the EMD Configuration page.

8. Set the status of Alarm-1 and/or Alarm-2 to “Normal Open”.

9. Place the SSL-WATER sensor in the desired location.

10. The installation of the SSL-WATER sensor is complete. See

-

’

LIMITED PRODUCT WARRANTY

Para Systems Inc. (Para Systems) warrants this equipment, when
properly applied and operated within specified conditions, against
faulty materials or workmanship for a period of three years from the
date of original purchase by the end user. For equipment sites within
the United States and Canada, this warranty covers repair o
replacement of defective equipment at the discretion of Para
Systems. Repair will be from the nearest authorized service center.
Replacement parts and warranty labor will be borne by Para Systems.
For equipment located outside of the United States and Canada, Para
Systems only covers faulty parts. Para Systems products repaired
or replaced pursuant to this warranty shall be warranted for the
remaining portion of the warranty that applies to the original product.
This warranty applies only to the original purchaser who must have
properly registered the product within 10 days of purchase.

The warranty shall be void if (a) the equipment is damaged by the
customer, is improperly used, is subjected to an adverse operating
environment, or is operated outside the limits of its electrical
specifications; (b) the equipment is repaired or modified by anyone
other than Para Systems or Para Systems-approved personnel; or (c)
has been used in a manner contrary to the product's operating
manual or other written instructions.

ny technical advice furnished before or after delivery in regard to use
or application of Para Systems’s equipment is furnished without
charge and on the basis that it represents Para Systems’s best

udgment under the circumstances, but it is used at the recipient's

sole risk.

EXCEPT AS PROVIDED HEREIN, PARA SYSTEMS MAKES NO
WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
PARTICULAR PURPOSE. Some states do not permit limitation o

implied warranties; therefore, the aforesaid limitation(s) may not appl
to the purchaser.

EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL PAR
SYSTEMS BE LIABLE FOR DIRECT, INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES ARISING OUT OF
THE USE OF THIS PRODUCT, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE. Specifically, Para Systems is

not liable for any costs, such as lost profits or revenue, loss o
equipment, loss of use of equipment, loss of software, loss of data,
cost of substitutes, claims by third parties, or otherwise. The sole
and exclusive remedy for breach of any warranty, expressed o
implied, concerning Para Systems’s products and the only obligation
of Para Systems hereunder, shall be the repair or replacement o
defective equipment, components, or parts; or, at Para Systems’s
option, refund of the purchase price or substitution with an equivalent
replacement product. This warranty gives you specific legal rights
and you may also have other rights, which vary from state to state.

OBTAINING TECHNICAL ASSISTANCE

Para Systems (Minuteman UPS) Technical Support:
Phone: [phone]
Fax: [phone]
Web: www.minutemanups.com/support/con_tech2.php

www.minutemanups.com © Copyright 2008 34000364 R1