Minuteman Endeavor, EDBP24XL, EDBP48XL, EDBP72XL User Manual
User's Manual
Endeavor Series
Battery Packs
1
© Copyright 2006
English
1. Introduction 2
2. Controls and Indicators 6
3. Installation 7
4. Operation 14
5. Troubleshooting 15
6. Replacing the Battery 16
7. Obtaining Service 20
8. Specifications 21
9. Limited Product Warranty 22
2
English
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS !
Thank you for purchasing this power protection product. It has been designed
and manufactured to provide many years of trouble free service.
Please read this manual before installing your Endeavor Series Battery Pack,
models EDBP24XL, EDBP48XL, EDBP72XL as it provides important information that should be followed during installation and maintenance of the Battery
Packs and batteries allowing you to correctly set up your system for the maximum safety and performance. Included is information on customer support
and factory service if it is required. If you experience a problem with the Battery
Packs please refer to the Troubleshooting guide in this manual to correct the
problem or collect enough information so that the Technical Support Department can rapidly assist you.
This symbol indicates "A TTENTION"
This symbol indicates "Risk of Electrical Shock"
This symbol indicates "Alternating Current Supply"
This symbol indicates "Alternating Current Supply Phase"
3
English
WARNING: Risk of Electrical Shock. Hazardous live parts inside
these Battery Packs are energized from the battery even when the
AC input is disconnected.
CAUTION! To de-energize the Battery Pack:
1. If the UPS is on press and release the Off button.
2. Disconnect the UPS and the Battery Pack from the wall outlet.
3. Turn off the DC breaker on the rear panel of the Battery Pack.
4. Disconnect the battery cable from the rear panel of the UPS.
5. T o de-energize the Battery Pack completely , disconnect the batteries.
CAUTION! These Battery Packs are intended to be install in a
temperature controlled environment that is free of conductive contaminants. Select a location which will provide good air circulation for
the Battery Pack and UPS at all times.
CAUTION! Connect the Battery Pack to a two pole, three wire
grounding AC wall outlet. The receptacle must be connected to the
appropriate branch protection (circuit breaker or fuse). Connection to
any other type of receptacle may result in a shock hazard and violate
local electrical codes. Do not use extension cords, adapter plugs, or
surge strips.
CAUTION! T o reduce the risk of electrical shock with the installa-
tion of these Battery Packs, with the UPS equipment and the connected equipment, the user must ensure that the combined sum of
the AC leakage current does not exceed 3.5mA.
This symbol indicates "Direct Current Supply"
This symbol indicates "Equipment Grounding Conductor"
WARNING: These Battery Packs contains potentially hazardous
voltages. Do not attempt to disassemble the Battery Pack beyond
the battery replacement procedure. These Battery Packs contains
no user serviceable parts. Repairs and Battery replacement must be
performed by QUALIFIED SERVICE PERSONNEL ONL Y.
4
English
NOTICE: This equipment has been tested and found to comply with
the limits for a Class A computing device in accordance with the speci-
fications in Subpart J of Part 15 of FCC Rules and the Class A limits for
radio noise emissions from digital apparatus set out in the Radio Interference of
the Canadian Department of Communications. These limits are designed to
provide reasonable protection against such interference in a residential installation. This equipment generates and uses radio frequency and if not installed
and used properly , that is, in strict accordance with the manufacturer's instructions, this equipment may cause interference to radio and television reception.
If this equipment does cause interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
Re-orient the receiving antenna.
Relocate the computer with respect to the receiver .
Move the computer away from the receiver .
Plug the computer into a different outlet so that the computer and receiver
are on different branch circuits.
Shielded communications interface cables must be used with this product.
WARNING: Changes or modifications to this unit not expressly ap-
proved by the party responsible for compliance could void the user's
authority to operate the equipment.
WARNING: Qualified Service Personnel ONLY must perform
the Installation and Servicing of these Battery Packs. MINUTEMAN
accepts no liabilities and is not limited to: injury to the Service Personnel, or damages to; the Battery Pack, the UPS, or the connected
equipment caused by the incorrect installation or servicing of the
Battery Packs. These Battery Packs MUST be operated with their
respective UPS models, see the table below:
EDBP24XL
UPS
Model #
ED1000RM2U
ED1000RMT2U
EDBP72XL
Model #
ED3000RM2U
ED3000RMT2U
EDBP48XL
ED1500RM2U
ED2000RM2U
ED1500RMT2U
ED2000RMT2U
5
English
Receiving Inspection
After removing your Battery Pack from its carton, it should be inspected for
damage that may have occurred in shipping. Immediately notify the carrier and
place of purchase if any damage is found. Warranty claims for damage caused
by the carrier will not be honored. The packing materials that your Battery
Pack was shipped in are carefully designed to minimize any shipping damage.
In the unlikely case that the Battery Pack needs to be returned to the manufacturer , please use the original packing material. Since the manufacturer is not
responsible for shipping damage incurred when the system is returned, the
original packing material is inexpensive insurance.
PLEASE SAVE THE PACKING MATERIALS!
Life Support Policy
As a general policy , we do not recommend the use of any of our products in life
support applications where failure or malfunction of the product can be reasonably expected to cause failure of the life support device or to significantly affect
its safety or effectiveness. We do not recommend the use of any of our products in direct patient care. We will not knowingly sell our products for use in
such applications unless it receives in writing assurances satisfactory to us
that (a) the risks of injury or damage have been minimized, (b) the customer
assumes all such risks, and (c) our liability is adequately protected under the
circumstances.
Examples of devices considered to be life support devices are neonatal oxygen
analyzers, nerve stimulators (whether used for anesthesia, pain relief, or other
purposes), auto transfusion devices, blood pumps, defibrillators, arrhythmia
detectors and alarms, pacemakers, hemodialysis systems, peritoneal dialysis
systems, neonatal ventilator incubators, ventilators for both adults and infants,
anesthesia ventilators, and infusion pumps as well as any other devices designated as “critical” by the United St ates FDA.
6
English
The Charger Active (green) LED illuminates in a steady state when the Charger is
on. The Charger Active LED will extinguish when there is no acceptable AC present.
The DC Breaker On (green) LED illuminates in a steady state when the DC breaker
is in the On position. The DC Breaker On LED will extinguish when the DC breaker
is in the Off position.
INDICATOR PANEL
REAR PANEL
1. The DC Circuit Breaker connects and disconnects the DC bus voltage from the
Battery Pack to the UPS. The DC Circuit Breaker will trip in the event of a DC over current condition.
2. The External Battery connector is for Daisy Chaining additional Battery Packs.
3. The dipswitch is for setting the input voltage for the Battery Pack's internal charger .
4. The AC Outlet is for connecting the output cable to Daisy Chain additional Battery
Packs.
5. The AC Inlet is for connecting the input power cord to operate the Charger.
6. The Input Breaker will trip in the event that the Internal Charger draws excessive
current.
7. The External Ground Stud is for connecting an external ground wire.
8. The External Battery cable is for connecting the Battery Pack to the UPS or Daisy
Chaining additional Battery Packs.
7
English
INSTALLATION PLACEMENT
These Battery Packs are intended to be install in a temperature controlled
environment that is free of conductive contaminants. Select a location which
will provide good air circulation for the Battery Pack at all times. Avoid locations near heating devices, water or excessive humidity , or where the Battery
Pack is exposed to direct sunlight. Route power cords so they cannot be
walked on or damaged.
INSTALLATION
Be sure to read the installation placement and all the cautions before installing
the Battery Pack. Place the Battery Pack in the final desired location and
complete the rest of the installation procedure.
WARNING! These Battery Packs are extremely heavy. Any time
the Battery Pack has to be handled be sure to use, enough personnel, strong supports and equipment to safely handle the Battery Pack.
ENVIRONMENT AL
Operating Temperature (max)
Operating/Storage Humidity
Operating Elevation
0 to 40°C (+32 to +104°F)
95% Non-Condensing
0 to 3,000m (0 to +10,000 ft)
Storage Elevation
0 to 15,000m (0 to +50,000 ft)
Storage Temperature -15 to +45°C (+5 to +1 13°F)
Audible Noise at 1 m (3 ft.)
<45 dBA
Loading...