CRV
Model: C80704-05 SS
Clean Room
Vacuum
Digital Switching
Station
OPERATION
SERVICE PARTS
C80704-06 PT
EMI/RFI Flitered
CARE
Revised 3/04
FOR COMMERCIAL USE ONLY
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precautions should always be followed, including the
following:
READ ALL INSTRUCTIONS BEFORE USING
WARNING
Do not leave appliance when plugged in. Unplug from outlet when not in use and before servicing.
- T o reduce the risk of fire, electric shock, or injury:
WARNING
Electric shock could occur if used on wet surfaces. Do not expose to rain. Store indoors.
• Never allow children or untrained adults to operate this equipment.
• Keep the area of operation clear of all persons, particularly small children, and pets.
• Keep bystanders at least 25 feet away from the area of operation.
• Use only as described in this manual. Use only manufacturer’s recommended attachments.
• Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped,
damaged, left outdoors, or dropped into water , return it to a service center .
• Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp
edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces.
• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
• Do not handle plug or appliance with wet hands.
• Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint,
hair , and anything that may reduce airflow .
• Keep hair , loose clothing, fingers, and all parts of body away from openings and moving parts.
• Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
• Do not use without dust bag and/or filters in place.
• Turn off all controls before unplugging.
• Use extra care when cleaning on stairs.
• Do not use to pick up flammable or combustible liquids such as gasoline or use in areas where
they may be present.
• Connect to a properly grounded outlet only . See grounding instructions.
SAVE THESE INSTRUCTIONS
1
INSPECTION
Carefully unpack and inspect your machine for shipping damage. Each unit is tested and thoroughly
inspected before shipment, and any damage is the responsibility of the delivery carrier who should
be notified immediately .
ELECTRICAL
This machine is designed to operate on a standard 15 amp. 115 volt, 60 hz, AC circuit. Volt ages
below 105 volts AC or above 125 volts AC could cause serious damage to the motor .
WARNING
Electric motors can cause explosions when operated near explosive materials or vapors. Do not
operate this machine near flammable materials such as solvents, thinners, fuels, grain dust, etc.
GROUNDING INSTRUCTIONS
This appliance must be grounded. If it should malfunction or breakdown, grounding provides a path
of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped
with a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged
into an appropriate outlet that is properly installed and grounded in accordance with all local codes
and ordinances.
DANGER
Improper connection of the equipment-grounding conductor can result in a risk of electric shock.
Check with a qualified electrician or service person if you are in doubt as to whether the outlet is
properly grounded. Do not modify the plug provided with the appliance — if it will not fit the outlet,
have a proper outlet installed by a qualified electrician.
This appliance is for use on a nominal 120-volt circuit and has a grounding plug that looks like the
plug illustrated in sketch A below . Make sure that the appliance is connected to an outlet having the
same configuration as the plug. No adapter should be used with this appliance.
2
USER MAINTENANCE INSTRUCTIONS
All service and repair should be performed by a qualified vacuum service representative or electrician.
No user serviceable components are employed in the electrical vacuum lid head assembly. No
lubrication of the motor is required.
CLOTH BAG & HOSE ASSY
Cloth bag and hose assy . are user maintenance items and can be replaced when worn out. Cloth
bags can be maintained by blowing dust off of the bag and then laundered. Cloth bags should be
completely dried before re-installing into machine. For optimum performance, empty and clean filter
bag regularly . A clogged and dirty bag restrict s the flow of air and results in reduced vacuum. The
hose assy. can be maintained by wiping off with a dampened cloth of mild liquid soap and water,
then allowed to dry .
CORD STORAGE
While not in use storage can be accomplished by winding cord around motor lid assy . Cord should
be completely unwound from lid assy . during operation.
• Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped,
damaged, left outdoors, or dropped into water , return to service center.
• Do not pull or carry by cord, use cord as handle, close a door on cord, or pull cord around sharp
edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces.
• Do not unplug by pulling cord. T o unplug, grasp the plug, not the cord.
• Do not handle plug or appliance with wet hands.
• Always unplug the machine when removing the head off the tank. This equipment should be stored
indoors and not exposed to rain.
OPERA TION AND FIL TER CARE INSTRUCTIONS
The Minuteman Digital Switching S tation Vacuum has been specially designed to reduce the incidence
of airborne dust, including carbon dust from motor cooling air, to a level of 99.999% ef ficiency at .12
micron size particles.
This unit is equipped with a red indicator light which will flash on and off while vacuum is in use. When
the red indicator remains illuminated, the operator should replace the filter collector bag and clean
the cloth filter as required. If indicator light still remains illuminated ULP A filter should be replaced.
PREP ARING V ACUUM FOR USE
1. Take the paper disposable filter bag with the cardboard collar attached and open the bag by
gently pulling the folds apart.
2. Insert the filter bag into the tank and push it to the bottom.
3. Locate the cardboard collar around the intake tube and gently work it past the raised ring that
runs around the tube.
4. Place the cloth filter bag onto and into the tank centering the metal ring around the rim of the tank.
5. Position the lid onto the tank and snap on lid latches. V acuum is ready for use.
PROCEDURE FOR CLEANING V ACUUM AND REPLACING FIL TER
1. Unplug electric cord from power source.
2. Carefully and slowly release lid latches and remove motor lid only .
3. Gently remove the cloth filter and inspect soil condition. Clean filter by shaking or brushing into
trash container.
4. Reach into tank and remove paper disposal filter bag.
5. Clean out vacuum tank of any debris that may have collected.
6. T o put vacuum back into service, follow “Preparing” procedure above.
3
4
PARTS LIST
Item Part No. Qty. Description
1 1 10014 1 Filter-ULPA 99.999 at .12 microns
2 130040POL 1 Handle Polished
3 250118 1 Hose, Neoprene C/L 3.00” Long
4 290017 2 Molded Vac Motor Gasket
5 380002 1 Switch, Toggle 1.5 HP 125V-250V
6 380028 2 Carbon Brush Replacement
7 380037 4 Bushing .196 x .313 x .203
8 380044 1 Lid Gasket 4/6, 40"
9 380066 1 Lid, SS CRV Vac
10 381001 1 Vac Motor , 631 1-00 120V
1 1 381020 1 Cord 16GA-3 50FT Med Gray
12 384001PLT 1 Bag Guard New Style
13 710153 8 SCR-MC 10-32 x .37 Zinc
14 710177 5 SCR-MC 1/4-20 X .37 Zinc
15 710356 12 SCR-MC 10-32 x .62 Zinc
16 711124 1 SCR-ST-B 10 X .37 NI
17 711310 4 Nut-Hex 10-32 ST PL
18 711351 8 Acorn Nut 10/32 ST N1
19 711373 4 Nut-Nyloc 1/4-20
20 711401 9 Nut-Riv 10-32
21 711553 17 WSR-Internal Lock #10
22 711554 5 WSR-Internal Lock 1/4
23 715025 1 Decal Filter Check CRV
24 715029 1 Decal Name Plate Serial
25 715093 1 Decal CRV Diecut Bellcor
26 715129 1 Decal On/Off CRV
27 715501 1 Decal Made in USA
28 740009 2 Ring 16-22G Non Ins #6
29 740026 4 Spade 14-16G Non Ins #10
30 740090 1 Light Socket & Lens
31 740091 1 Pilot Neon 115V NE2J
32 740148 1 RFI KMT 254/950-410-750
33 740224 1 Switch Pressure 502 351 W
34 750000 1 Assy. Motor Hold Down
35 750195 1 Silencer Dome Assy.
36 760247 1 O-Ring .312 ID x .442 x .065
37 760281PTD 1 Cover HEPA Filter Painted
38 760291 1 Gasket
39 760650 1 Hexseal Switch Boot
40 761289 1 Liner Felt, .4.50 x 26.5
41 761291 1 Felt, .62 x 9.00 x .50
42 800046 1 Air Diffuser CRV
43 833237 1 Strain Relief w/Nut
**** 800047 CRV Lid Asy w/RFI 1 15V
5
PARTS LIST
Item Part No. Q t y. Description
1 130032 2 Cap Retainer
2 280016 2 Caster 3” w 3/8 x 5/8 Stem
3 390087 1 Gasket Diecut VNN
4 390110 1 Intake Assy Aluminum
5 711005 4 SK 1/4-20 x .31
6 711006 3 SK 1/4-20 x .62
7 711503 4 WSR-FL T #10
8 711524 2 WSR-Wave .52 x .87 x .01
9 711594 2 WSR-FL T .56 x .88 x .03 Nickel
10 711713 2 Ret Ring-E Ext .50
11 71 1915 4 Rivet-Tube .19 x .28 NI PL
12 712638 2 Nut Hex 10-24 SS Nyloc
13 712824 2 SCR-THMS 10-24 x .75 STPL Zinc
14 715383 1 Decal, MMN 1 x 6.88 Lt Gray
15 750118 1 Intake Assy Tube 4/6 Gal
16 760083 2 Wheel 6” 6-105 .5 ID
17 761054 2 Latch
18 900055PTD 1 Bracket, Wheel 4/6 Gal
19 900066 2 Axle
20 900085 1 T ank, 4 Gal. PTD
20A 900109 1 Tank, 4 Gal. SS Low Intake
6
P ARTS LIST
Item Part No. Qty . Description
1 760244 1 Molded Bag Ring
2 805043 1 Cloth Filter 4 Gallon
3 805044 1 Bag Assy . Complete 4 Gallon
7
8
A
OPTIONAL TOOLS & ATT ACHMENTS
Part No. Description
800317 Hose Asy with Swivel Cuf f 1 1/2 x 10
390014 Cuff
801044 Hose
B
C
D
E
F
801044 Hose Only 1 1/2 x 10
761228 Wand Asy 1 1/2, Complete
601032 - 1 1” Carpet Floor Tool
808422 - Adj. Lever
133217 - Adj Screw
17916 - Replacement Brush
800083 3” Round Dust Brush
133249 Adapter Brush
800084 Bristle
808023 Adapter
801015 Hose Cuff
808397 - Nozzle
712065 - Screw
133214 - Spring
133215 - Sleeve
G
H
I
J
K
800020 Hose Coupling 1 1/2
800124 Plastic 5” Upholstery Tool
384003PKG Disposable Paper Bags, Pkg of 10
761177PKG Filter Protectors, Pkg of 12
800104 Crevice Tool
9
LIMITED WARRANTY
Minuteman International, Inc. warrants to the original purchaser/user that this product is free from defects in workmanship and
materials under normal use and service for a period of three years from date of purchase. In addition, Minuteman International, Inc.
will, at its option, honor labor warranty claims for the first 12 months from date of sale, provided such claims are submitted through
and approved by factory authorized repair stations. Minuteman International, Inc. will, at its option, repair or replace without charge,
except for transportation costs, parts that fail under normal use and service when operated and maintained in accordance with the
applicable operation and instruction manuals.
This warranty does not apply to normal wear, or to items whose life is dependent on their use and care, such as belts, cords,
switches, hoses, rubber parts, electrical motor components or adjustments. Parts not manufactured by Minuteman International, Inc.
such as engines, batteries, battery chargers, hydraulic pumps, and tires are covered by and subject to the warranties and/or guarantees
of their manufacturers. Please contact Minuteman International, Inc. for procedures in warranty claims against these manufacturers.
Special warning to purchaser — Use of replacement filters and/or prefilters not manufactured by Minuteman International, Inc. or
its designated licensees, will void all warranties expressed or implied.
A potential health hazard exists without exact original equipment replacement.
All warranteed items become the sole property of Minuteman International, Inc. or its original manufacturer, whichever the case may
be.
Minuteman International, Inc. disclaims any implied warranty, including the warranty of merchant ability and the warranty of fitness for
a particular purpose. Minuteman International, Inc. assumes no responsibility for any special, incidental or consequential damages.
This limited warranty is applicable only in the U.S.A. and Canada, and is extended only to the original user/purchaser of this product.
Customers outside the U.S.A. and Canada should contact their local distributor for export warranty policies. Minuteman International,
Inc. is not responsible for costs or repairs performed by persons other than those specifically authorized by Minuteman International,
Inc. This warranty does not apply to damage from transportation, alterations by unauthorized persons, misuse or abuse of the
equipment, use of non-compatible chemicals, or damage to property , or loss of income due to malfunctions of the product.
If a difficulty develops with this machine, you should contact the dealer from whom it was purchased.
This warranty gives you specific legal rights, and you may have other rights which vary from state to state. Some states do not allow
the exclusion or limitation of special, incidental or consequential damages, or limitations on how long an implied warranty lasts, so the
above exclusions and limitations may not apply to you.
A Member of the Hako Group of Companies
World Headquarters Minuteman Canada, Inc.
Minuteman International, Inc. 2210 Drew Road
111 South Rohlwing Road Mississauga, Ontario
Addison, Illinois 60101 L5S 1B1
Phone 630-627-6900 Phone 905-673-3222
Fax 630-627-1 130 Fax 905-673-5161
www.minutemanintl.com
Printed in U.S.A.
987917
Loading...