Carpet Spotter
Model: C46200-00Model: C46200-00
Model: C46200-00
Model: C46200-00Model: C46200-00
C46200-02C46200-02
C46200-02
C46200-02C46200-02
C46200-02CEC46200-02CE
C46200-02CE
C46200-02CEC46200-02CE
OPERAOPERA
OPERA
OPERAOPERA
TIONTION
TION
TIONTION
SERVICESERVICE
SERVICE
SERVICESERVICE
PP
P
PP
ARAR
AR
ARAR
TSTS
TS
TSTS
CARECARE
CARE
CARECARE
Revised 9/05
FOR COMMERCIALFOR COMMERCIAL
FOR COMMERCIAL
FOR COMMERCIALFOR COMMERCIAL
USE ONL USE ONL
USE ONL
USE ONL USE ONL
YY
Y
YY
IMPORIMPOR
IMPOR
IMPORIMPOR
When using an electrical appliance, basic precautions should always be followed, including the
following:
READ READ
READ
READ READ
WW
ARNINGARNING
W
ARNING -
WW
ARNINGARNING
• Do not leave appliance when plugged in. Unplug from outlet when not in use and before servicing.
WW
ARNINGARNING
W
ARNING
WW
ARNINGARNING
To reduce the risk of electrical shock, do not expose to rain. Store indoors.
• Use motorized tool on carpet moistened by the cleaning process.
• Do not allow to be used as a toy. Close attention is necessary when used by or near children.
• Use only as described in this manual. Use only manufacturer’s recommended attachments.
• Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped,
damaged, left outdoors, or dropped into water, return it to a service center.
• Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp
edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces.
• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
• Do not handle plug or appliance with wet hands.
• Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint,
hair, and anything that may reduce air flow.
• Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
• Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
• Do not use without dust-bag and/or filters in place.
• Turn off all controls before unplugging.
• Use extra care when cleaning on stairs.
• Do not use to pick up flammable or combustible liquids such as gasoline or use in areas where
they may be present.
• Connect to a properly grounded outlet only. See grounding instructions.
ALLALL
ALL
ALLALL
INSTRUCTIONS BEFORE USING INSTRUCTIONS BEFORE USING
INSTRUCTIONS BEFORE USING
INSTRUCTIONS BEFORE USING INSTRUCTIONS BEFORE USING
TT
o reduce the risk of fire, electric shock, or injury:o reduce the risk of fire, electric shock, or injury:
T
o reduce the risk of fire, electric shock, or injury:
TT
o reduce the risk of fire, electric shock, or injury:o reduce the risk of fire, electric shock, or injury:
TT
ANTANT
T
ANT
TT
ANTANT
SAFETY SAFETY
SAFETY
SAFETY SAFETY
INSTRUCTIONS INSTRUCTIONS
INSTRUCTIONS
INSTRUCTIONS INSTRUCTIONS
SASA
SA
SASA
VE VE
THESE INSTRUCTIONSTHESE INSTRUCTIONS
VE
THESE INSTRUCTIONS
VE VE
THESE INSTRUCTIONSTHESE INSTRUCTIONS
1
INSPECTIONINSPECTION
INSPECTION
INSPECTIONINSPECTION
Carefully unpack and inspect your machine for shipping damage. Each unit is tested and thoroughly
inspected before shipment, and any damage is the responsibility of the delivery carrier who should
be notified immediately.
ELECTRICALELECTRICAL
ELECTRICAL
ELECTRICALELECTRICAL
This machine is designed to operate on a standard 15 amp. 115 volt, 60 hz, AC circuit. Voltages
below 105 volts AC or above 125 volts AC could cause serious damage to the motor.
ELECTRICAL - ELECTRICAL -
ELECTRICAL -
ELECTRICAL - ELECTRICAL -
This machine is designed to operate on a standard 16 amp. type L fused 230 volt, 50 hz, AC circuit.
Voltages below 200 volts AC or above 250 volts AC could cause serious damage to the motor.
I.E.C. Class 1.
WW
ARNINGARNING
W
ARNING
WW
ARNINGARNING
Electric motors can cause explosions when operated near explosive materials or vapors. Do not
operate this machine near flammable materials such as solvents, thinners, fuels, grain dust, etc.
GROUNDING INSTRUCTIONSGROUNDING INSTRUCTIONS
GROUNDING INSTRUCTIONS
GROUNDING INSTRUCTIONSGROUNDING INSTRUCTIONS
This appliance must be grounded. If it should malfunction or breakdown, grounding provides a path
of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped
with a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged
into an appropriate outlet that is properly installed and grounded in accordance with all local codes
and ordinances.
- -
Model C46200-00 (1Model C46200-00 (1
-
Model C46200-00 (1
Model C46200-00 (1Model C46200-00 (1
- -
Model C46200-02, C46200-02CE (230V)Model C46200-02, C46200-02CE (230V)
Model C46200-02, C46200-02CE (230V)
Model C46200-02, C46200-02CE (230V)Model C46200-02, C46200-02CE (230V)
15V)15V)
15V)
15V)15V)
DANGERDANGER
DANGER - Improper connection of the equipment-grounding conductor can result in a risk of
DANGERDANGER
electric shock. Check with a qualified electrician or service person if you are in doubt as to whether
the outlet is properly grounded. Do not modify the plug provided with the appliance -- if it will not fit the
outlet, have a proper outlet installed by a qualified electrician.
This appliance is for use on a nominal 120-volt circuit and has a grounding plug that looks like the
plug illustrated in sketch A below. Make sure that the appliance is connected to an outlet having the
same configuration as the plug. No adapter should be used with this appliance.
2
USER MAINTENANCE INSTRUCTIONSUSER MAINTENANCE INSTRUCTIONS
USER MAINTENANCE INSTRUCTIONS
USER MAINTENANCE INSTRUCTIONSUSER MAINTENANCE INSTRUCTIONS
All service and repair should be performed by qualified vacuum service representative or electrician.
No user serviceable components are employed in the electrical vacuum lid head assembly. No
lubrication of the motor is required.
DAILDAIL
DAIL
DAILDAIL
1. Solution tank should be emptied after each use. Flush pumping system with 1 gallon of clean
2. Check and clean vacuum inlet and solution inlet strainer daily.
3. Removable recovery tank, page 7, item 30, should be rinsed clean daily.
4. Spray jet should be checked for correct spray pattern and cleaned if plugged. Do not clean out
5. Protect equipment from freezing. Severe pumping system damage can occur if allowed to freeze.
6. Inspect vacuum hoses for tight connections. Check electrical cable for abrasion or cuts in jacket.
MONTHLMONTHL
MONTHL
MONTHLMONTHL
The Solution Pump System should be purged monthly to remove alkaline residue build-up. To flush
system out, use 1 quart of white vinegar to 1 1/2 gallons of clean hot water, followed by a clear 1 1/2
gallon rinse. Clean spray jets if required.
CORD STORAGECORD STORAGE
CORD STORAGE
CORD STORAGECORD STORAGE
While not in use storage can be accomplished by winding cord around top of machine. Cord hooks
are provided.
YY
MAINTENANCE MAINTENANCE
Y
MAINTENANCE
YY
MAINTENANCE MAINTENANCE
water after use.
spray tip with pins or wire, this may cause damage to the jet spray pattern and cause streaking.
Cord should be replaced if worn or damaged.
Y/BI-MONTHLY/BI-MONTHL
Y/BI-MONTHL
Y/BI-MONTHLY/BI-MONTHL
YY
MAINTENANCE MAINTENANCE
Y
MAINTENANCE
YY
MAINTENANCE MAINTENANCE
• Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped,
damaged, left outdoors, or dropped into water, return to service center.
• Do not pull or carry by cord, use cord as handle, close a door on cord, or pull cord around sharp
edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces.
• Do not unplug by pulling cord. To unplug, grasp the plug, not the cord.
• Do not handle plug or appliance with wet hands.
This equipment should be stored indoors and not exposed to rain.
3
OPERAOPERA
OPERA
OPERAOPERA
1. Lift the recovery tank of solution tank by releasing the two latches.
2. Add up to 1 1/2 gallons of hot water (maximum 140°F) to the solution tank. If chemicals are
required, follow dilution ratios as specified on product label. Use only commercially available
cleaning chemicals intended for use on carpet.
3. Place recovery tank back on solution tank and fasten the two latches.
4. Plug power cord into grounded wall outlet.
5. Connect the vac/solution hose assembly to machine.
6. This machine is equipped with a 3-position power switch. Ref. to figure below. The single bar
position is for vacuum only - center position is off. Double bar position is for vacuum pump and
motorized tool (120V and standard 230V). Turn on machine in the single bar position (CE version
230V only).
7. Always test upholstery for color fastness in a hidden area before beginning cleaning process.
TING INSTRUCTIONSTING INSTRUCTIONS
TING INSTRUCTIONS
TING INSTRUCTIONSTING INSTRUCTIONS
WW
arning:arning:
8.
W
arning: This unit does not contain any automatic liquid shut-off devices in the vacuum recovery
WW
arning:arning:
tank. Do not overfill. Always completely empty recovery tank before refilling solution tank. If foam
or liquid comes out of ventilation openings turn off immediately. Remove recovery tank and run
for 1 minute to flush all liquid from vacuum fan chamber.
4
BEFORE EACH USE OF THE CARPET SPOTTER:BEFORE EACH USE OF THE CARPET SPOTTER:
BEFORE EACH USE OF THE CARPET SPOTTER:
BEFORE EACH USE OF THE CARPET SPOTTER:BEFORE EACH USE OF THE CARPET SPOTTER:
5
6
PartPart
s Listing - 120V & 240Vs Listing - 120V & 240V
Part
s Listing - 120V & 240V
PartPart
s Listing - 120V & 240Vs Listing - 120V & 240V
ItemItem
Item
ItemItem
10 450247 1 Top Gasket
11 450251 1 Vac Motor Shroud
12 450252 1 Bottom Gasket
13 450253 1 Front Gasket
14 450254 1 Gasket, GFCI (not shown)
15 452037 1 Crimp Clamp 170R
16 710207 1 SCR-MC 6-32 x .87 ST PL
17 711104 2 SCR-ST B 10 x .37
18 711124 1 SCR-ST B 10 x .37 NI
19 711301 1 Nut-Hex 6-32
20 711400 1 Nut-Pipe Lock 1/4 NPT
21 711504 6 WSR-Flat 1/4 SS
22 711553 1 WSR-INT Lock #10
23 712532 4 SCR-MC 10-24 x 1.00 SS
24 712537 1 SCR-MC 10-24 x .75 SS
25 712543 4 SCR-MC 10-24 x 3.50 FH SS
26 712560 2 SCR-MC 1/4-20 x .50 SS Nyloc
27 712638 8 Nut-Hex 10-24 SS Nyloc
28 712770 2 WSR-Int. Tooth #10
29 712905 2 Nut-Hex 10-24
30 712908 1 Nut-Flanged Wizz 10-24
31 715009 1 Decal - Warning
32 715029 1 Decal - Serial Number
33 715179 1 Decal - Spotter Switch
34 715340 1 Decal - (120V)
34A 715341 1 Decal - (240V)
35 715501 1 Decal - Made in USA
36 740099 2 Wire Tie Small (not shown)
37 740387 1 Cord 18-3, 25 FT, Spade Term
37A 742248 1 Cord Asm 230V Crptsptr
38 740448 1 Ground Fault Interrupter 115V Only
39 740726 1 Terminal Block 3-Position
39A 742101 1 Terminal Block 4-Position
40 741038 1 Receptacle
41 742102 1 Switch 2-Position
42 742196 1 Wire Asy Grn/Yel 16G
43 742244 1 Vac Motor Assembly 115V
43A 742346-1 1 Vac Motor Assembly 230Vac w/Therm
44 742240 1 Wire Asy Violet 16G (120V only)
44A 742250 1 Wire Asy Violet 16G (230V only)
45 742241 1 Wire Asy Black 16G
46 742242 1 Wire Asy White 16G (120V only)
47 742243 1 Wire Asy White 16G
48 742245 1 Wire Asy Grn/Yel 16G
49 75-89A 4 Nut-Speed
50 762299 2 Rubber Grommet
51 829757 1 Pump 50 PSI 115V
51A 742150 1 Pump 230V Bypass
52 828490 1 Crimp Clamp 140R
Part NoPart No
Part No
Part NoPart No
1 150004 1 Heyco Stain Relief
2 380064 1 Foam Ring
3 410-4419AA 2 Pop Rivet
4 450040 1 Elbow PLT 3/8 MPT x 3/8 Barb
5 450213 1 Frame Weldment (120V)
5A 450235 1 Frame Weldment (230V)
6 450222 1 Elbow PLT 3/8 MPT x 1/4 Barb
7 450226 2 Wheel 4"
8 450227 1 Hose Input 3/8 ID x 12 CL
9 450228 1 Hose Output 1/4 ID x 15 CL
QtyQty
Qty
QtyQty
DescriptionDescription
Description
DescriptionDescription
7
450220CE 230V European Part450220CE 230V European Part
450220CE 230V European Part
450220CE 230V European Part450220CE 230V European Part
ItemItem
Item
ItemItem
Part NoPart No
Part No
Part NoPart No
1 150004 1 Heyco Stain Relief
2 380064 1 Foam Ring
3 410-4419AA 2 Pop Rivet
4 450040 1 Elbow PLT 3/8 MPT x 3/8 Barb
5 450213CE 1 Frame Weldment
6 450222 1 Elbow PLT 3/8 MPT x 1/4 Barb
7 450226 2 Wheel 4"
8 450227 1 Hose Input 3/8 ID x 12 CL
9 450228 1 Hose Output 1/4 ID x 15 CL
10 450247 1 Top Gasket
11 450251 1 Vac Motor Shroud
12 450252 1 Bottom Gasket
13 450253 1 Front Gasket
14 450299 1 EMI Filter Mounting Plate
15 452037 1 Crimp Clamp 170R
16 710207 1 SCR-MC 6-32 x .87 ST PL
17 711124 3 SCR-ST B 10 x .37 NI
18 711301 1 Nut-Hex 6-32
19 711304 2 Nut-Hex 8-32 ST PL
20 711400 1 Nut-Pipe Lock 1/4 NPT
21 711504 6 WSR-Flat 1/4 SS
22 711553 1 WSR-INT Lock #10
23 712532 4 SCR-MC 10-24 x 1.00 SS
24 712537 1 SCR-MC 10-24 x .75 SS
25 712543 4 SCR-MC 10-24 x 3.50 FH SS
26 712560 2 SCR-MC 1/4-20 x .50 SS Nyloc
27 712638 4 Nut-Hex 10-24 SS Nyloc
QtyQty
Qty
QtyQty
DescriptionDescription
Description
DescriptionDescription
s Listings Listing
s Listing
s Listings Listing
ItemItem
Item
ItemItem
Part NoPart No
Part No
Part NoPart No
28 712905 2 Nut-Hex 10-24
29 712908 1 Nut-Flanged Wizz 10-24
30 715009 1 Decal - Warning
31 715029 1 Decal - Serial Number
32 715501 1 Decal - Made in USA
33 715633 1 Decal - CE
34 740010 1 Ring #10 14-16G Non-Insul
35 740014 2 Terminal Insulated
36 740018 2 FEM RT Ang 14-16G INS 1/4”
37 740099 2 Wire Tie Small (not shown)
38 740711CE 1 Switch 2 Position
39 740726 1 Terminal Screw Tab
40 741038 1 Recepticle, IEC 320
41 742150 1 Pump 230V Bypass
42 742240 1 Wire Asy Black 16G
43 742243 1 Wire Asy White 16G
44 742245 1 Wire Asy Grn/Yel 16G
45 742249 1 Wire Asy White 16G
46 742250 1 Wire Asy Violet 16G
47 712256 1 EMI Filter
48 742292 1 Ambassador CE RFI Torrid
49 742346-1 1 Vac Motor Assy 230vac w/Therm
50 742381 1 Cord Set 25 ft. 1.0 m.m.
51 75-89A 4 Nut-Speed
52 762299 2 Rubber Grommet
53 828490 1 Crimp Clamp 140R
QtyQty
Qty
QtyQty
DescriptionDescription
Description
DescriptionDescription
8
PartPart
Part
PartPart
ITEMITEM
ITEM
ITEMITEM
1 000708 .03 RTV Sealant
2 260294 1 Gasket
3 430103 2 Spring Hook
4 450201 1 Recovery Tank
5 450202MCH 1 Solution Tank Machined
6 450205 1 Quick Disconnect Plate
7 450207 2 Latch
8 450209 1 Gasket
9 450214 1 Strap
10 450215 1 Vac Pre-filter
11 450216 1 Solution Hose
12 450221 1 Quick Connect Coupler
13 450225 1 1/4 BARB x 1/8 FPT Brass
14 450229 1 Filter Assembly
15 452037 1 Crimp Clamp 170R
16 710025 8 SCR-MC 8-32 x 3/8 SS
PP
ARAR
TT
NO NO
NO
NO NO
QTYQTY
QTY
QTYQTY
P
AR
T
PP
ARAR
TT
DESCRIPTIONDESCRIPTION
DESCRIPTION
DESCRIPTIONDESCRIPTION
s Listings Listing
s Listing
s Listings Listing
ITEMITEM
ITEM
ITEMITEM
17 711552 8 WSR-Int Tooth 8
18 711594 3 WSR-Flat .56 x .88 x .03
19 712540 16 SCR-MC 10-24 x 3/8 SS
20 712621 2 Nut-Keps 8-32 SS
21 712767 3 WSR-Flat .406 x .75 x .03 SS
22 712770 16 WSR-Int Tooth 10
23 715180 1 Decal
24 715188 2 Decal, Gotcha!
25 715380 2 Decal, Minuteman
26 828490 1 Crimp Clamp 140R
27 828952 1 3/8 BARB x 1/4 MPT PLS
28 828974 1 Strainer
29 832326 1 O-Ring
30 833473 1 3/8 Hose BARB x 1/4 FPT
31 833906 1 1/4 Street 45 Brass
PP
P
PP
ARAR
AR
ARAR
TT
T
TT
NO NO
NO
NO NO
QTYQTY
QTY
QTYQTY
DESCRIPTIONDESCRIPTION
DESCRIPTION
DESCRIPTIONDESCRIPTION
9
Optional CartOptional Cart
Optional Cart
Optional CartOptional Cart
450240450240
450240
450240450240
Optional Spotter KitOptional Spotter Kit
Optional Spotter Kit
Optional Spotter KitOptional Spotter Kit
902000902000
902000
902000902000
PartPart
s Listings Listing
Part
s Listing
PartPart
s Listings Listing
ITEMITEM
ITEM
ITEMITEM
10 902000 1 Optional - Carpet Spotting Kit
PP
ARAR
TT
NO NO
NO
NO NO
QTYQTY
QTY
QTYQTY
P
AR
T
PP
ARAR
TT
1 130032 2 Hub Cap
2 280016 1 3” Caster
3 450238 1 Handle Weldment
4 450239 1 Frame Weldment
5 711350 2 Nut 10-32 Nyloc
6 711375 1 Nut 3/8-16 Nyloc
7 711508 1 WSR .44 x 1.0 x .09
8 712546 2 SCR-MC 10-32 x 1.0 SS
9 900008 2 8” Dia Wheel
DESCRIPTIONDESCRIPTION
DESCRIPTION
DESCRIPTIONDESCRIPTION
10
SS
potter potter
S
potter
SS
potter potter
450250450250
450250
450250450250
TT
ool Completeool Complete
T
ool Complete
TT
ool Completeool Complete
PartPart
s Listings Listing
Part
s Listing
PartPart
s Listings Listing
ITEMITEM
ITEM
ITEMITEM
10 390062 1 O-Ring, Valve Seat
11 390063 1 Pin
12 390064 1 Coupling
13 390066 1 Solution Valve Assy Comp
14 450248 1 Spray Jet
15 711803 1 Cotter Pin .06 x .75
16 712320 1 WSR-Nylon .22 x .45 x .04
17 712545 1 SCR-MC 10-32 x .87 SS
18 712636 1 Nut, Hex 10-32 SS
19 450249 1 Hose Assy Comp
PP
ARAR
TT
NO NO
NO
NO NO
QTYQTY
QTY
QTYQTY
P
AR
T
PP
ARAR
TT
1 390049 1 Spring
2 390052 1 Body
3 390053 1 Trigger
4 390054 1 Valve Stem, Brass
5 390055 1 Cap, Valve
6 390056 1 Mount
7 390059 1 Nozzel
8 390060 1 O-Ring, Seal Valve
9 390061 1 O-Ring, Valve Stem
450210 1 Solution Hose, 9.5 Ft
450211 1 Vacuum Hose Assy
450218 1 1/4 FPT x 1/8 Barb Brass
450219 1 Q-Connect Male 22-2 SS
450223 1 1/8 Barb x 1/8 FPT Brass
828062 6 Cable Tie Large
830082 2 Hose Clamp 3/8
DESCRIPTIONDESCRIPTION
DESCRIPTION
DESCRIPTIONDESCRIPTION
11
12
13
LIMITED WLIMITED W
LIMITED W
LIMITED WLIMITED W
Minuteman International, Inc. warrants to the original purchaser/user that this product is free from defects in workmanship and
materials under normal use and service for a period of one year from date of purchase. In addition, Minuteman International,
Inc. will, at its option, honor labor warranty claims for the first 12 months from date of sale, provided such claims are submitted
through and approved by factory authorized repair stations. Minuteman International, Inc. will, at its option, repair or replace
without charge, except for transportation costs, parts that fail under normal use and service when operated and maintained in
accordance with the applicable operation and instruction manuals.
This warranty does not apply to normal wear, or to items whose life is dependent on their use and care, such as belts, cords,
switches, hoses, rubber parts, electrical motor components or adjustments. Parts not manufactured by Minuteman International,
Inc. such as engines, batteries, battery chargers, hydraulic pumps, and tires are covered by and subject to the warranties and/
or guarantees of their manufacturers. Please contact Minuteman International, Inc. for procedures in warranty claims against
these manufacturers.
Special warning to purchaserSpecial warning to purchaser
Special warning to purchaser — Use of replacement filters and/or prefilters not manufactured by Minuteman International,
Special warning to purchaserSpecial warning to purchaser
Inc. or its designated licensees, will void all warranties expressed or implied.
A potential health hazard exists without exact original equipment replacement.
All warranteed items become the sole property of Minuteman International, Inc. or its original manufacturer, whichever the case
may be.
Minuteman International, Inc. disclaims any implied warranty, including the warranty of merchantability and the warranty of
fitness for a particular purpose. Minuteman International, Inc. assumes no responsibility for any special, incidental or
consequential damages.
ARRANTYARRANTY
ARRANTY
ARRANTYARRANTY
This limited warranty is applicable only in the U.S.A. and Canada, and is extended only to the original user/purchaser of this
product. Customers outside the U.S.A. and Canada should contact their local distributor for export warranty policies. Minuteman
International, Inc. is not responsible for costs or repairs performed by persons other than those specifically authorized by
Minuteman International, Inc. This warranty does not apply to damage from transportation, alterations by unauthorized persons,
misuse or abuse of the equipment, use of non-compatible chemicals, or damage to property, or loss of income due to
malfunctions of the product.
If a difficulty develops with this machine, you should contact the dealer from whom it was purchased.
This warranty gives you specific legal rights, and you may have other rights which vary from state to state. Some states do not
allow the exclusion or limitation of special, incidental or consequential damages, or limitations on how long an implied
warranty lasts, so the above exclusions and limitations may not apply to you.
A Minuteman International Company
World HeadquartersWorld Headquarters
World Headquarters Minuteman Canada, Inc.
World HeadquartersWorld Headquarters
Minuteman International, Inc. 2210 Drew Road
111 South Rohlwing Road Mississauga, Ontario
Addison, Illinois 60101 L5S 1B1
(630) 627-6900 (905) 673-3222
FAX (630) 627-1130 FAX (905) 673-5161
988610
Rev. A 9/05
Printed in U.S.A.
Loading...