Minuteman C39085-02, C39105-01, C39085-03, C39085-04, C39105-02 Operation, Service & Parts Manual

390 Vacuum

Model No: C39085-01,02,03,04

Series
15, 30 & 55
Gallon Units

Stainless Steel
& Painted

OPERATION

SERVICE PARTS

C39105-01,02,03,04

C39130-01,02,03,04
C39330-01,02,03,04,05,06
C39055-01,02,03,04,05,06

CARE

Revised 7/02

FOR COMMERCIAL USE ONLY

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic precautions should always be followed, including the
following:

READ ALL INSTRUCTIONS BEFORE USING

WARNING - To reduce the risk of fire, electric shock, or injury:

• Do not leave appliance when plugged in. Unplug from outlet when not in use and
before servicing.

• To avoid electrical shock, do not expose to rain, store indoors.

WARNING:

To reduce the risk of electrical shock - Do not use on wet surfaces. Do not expose to
rain. Store indoors.

• Do not allow to be used as a toy. Close attection is necessary when used by or near
children.

• Use only as described in this manual. Use only manufacturer’s recommended

attachments.

• Do not use with damaged cord or plug. If appliance is not working as it should, has
been dropped, damaged, left outdoors, or dropped into water, return it to a service
center.

• Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord
around sharp edges or corners. Do not run appliance over cord. Keep cord away
from heated surfaces.

• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

• Do not handle plug or appliance with wet hands.

• Do not put any object into openings. Do not use with any opening blocked; keep
free of dust, lint, hair, and anything that may reduce air flow.

• Keep hair, loose clothing, fingers, and all parts of body away from openings and

moving parts.

• Do not pick up anything that is burning or smoking, such as cigarettes, matches,
or hot ashes.

• Do not use without dustbag and/or filters in place.

• Turn off all controls before unplugging.

• Use extra care when cleaning on stairs.

• Do not use to pick up flammable or combustible liquids such as gasoline or use in
areas where they may be present.

• Connect to a properly grounded outlet only. See grounding instructions.

SAVE THESE INSTRUCTIONS

1

INSPECTION

Carefully unpack and inspect your machine for shipping damage. Each unit is tested and thoroughly
inspected before shipment, and any damage is the responsibility of the delivery carrier who should
be notified immediately.

ELECTRICAL - 115 Volt

This machine is designed to operate on a standard 15 amp. 115 volt, 60 hz, AC circuit. Voltages
below 105 volts AC or above 125 volts AC could cause serious damage to the motor.

ELECTRICAL - 240 Volt

This machine is designed to operate on a standard 10 amp. 230 volt, 50 hz, AC circuit.

GROUNDING INSTRUCTIONS

This appliance must be grounded. If it should malfunction or breakdown, grounding provides a path
of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped
with a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged
into an appropriate outlet that is properly installed and grounded in accordance with all local codes
and ordinances.

DANGER

Improper connection of the equipment-grounding conductor can result in a risk of electric shock.
Check with a qualified electrician or service person if you are in doubt as to whether the outlet is
properly grounded. Do not modify the plug provided with the appliance — if it will not fit the outlet,
have a proper outlet installed by a qualified electrician.

This machine is for use on a nominal 120 volt circuit and has a grounding plug that looks like the plug
illustrated in Sketch A. Make sure that the machine is connected to an outlet having the same
configuration as the plug. No adapter should be used with this appliance.

2

WARNING

This vacuum may contain potentially hazardous dust depending on its appilcation. Special
handling of contaminated disposal bags and filters is recommended. Disposal must be in
compliance with local EPA regulations

USER MAINTENANCE INSTRUCTIONS

All service and repair should be performed by qualified vacuum service representative or electrician.
No user serviceable components are employed in the electrical vacuum lid head assembly. No
lubrication of the motor is required.

CLOTH BAG & HOSE ASSEMBLY

Cloth bag and hose assembly are user maintenance items and can be replaced when worn out. For
optimum performance, empty and clean filter bag regularly. A clogged and dirty bag restricts the
flow of air and results in reduced vacuum. The hose assembly can be maintained by wiping off with
a dampened cloth of mild liquid soap and water, then allowed to dry.

CORD STORAGE

While not in use storage can be accomplished by winding cord around motor lid assembly. Cord
should be completely unwound from lid assembly during operation.

• Do not use with damaged cord or plug. If appliance is not working as it should, has been
dropped, damaged, left outdoors, or dropped into water, return to service center.

• Do not pull or carry by cord, use cord as handle, close a door on cord, or pull cord around
sharp edges or corners. Do not run appliance over cord. Keep cord away from heated
surfaces.

• Do not unplug by pulling cord. To unplug, grasp the plug, not the cord.

• Do not handle plug or appliance with wet hands.

• Always unplug the machine when removing the motor head off the tank.
This equipment should be stored indoors and not exposed to rain.

Always unplug the machine when removing the motor head off the tank. This equipment should be
stored indoors and not expposed to rain.

3

OPTIONAL INDUSTRIAL TOOLS AND ACCESSORIES

Part No. Description

800024 3” Rd Dust Brush Complete
800022 5” Rd Dust Brush Complete
800023 Bristle Insert 5”

A

800175MCH Dust Brush HSG 5”
800176MCH Dust Brush HSG 3”
800025 Bristle Insert 3”

800034 24” Crev Tool Aluminum Comp

B

C

D

E

F

G

H

800015 Wand Asy 1-1/2, Complete

800017 Set Tube, High-up 10’
800064 5’ Tube Lower Section
800019 5’ Section Upper

800116 Swivel, Hose End Exp, Comp

800317 Hose Asy 1-1/2 x 10’

800032 6” Curved Pipe Tool, Comp
711006 Set Screw
800033 Bristle Insert Curved 6’
800193POL 6” Curved Pipe Tool

800070 12” Gulper Tool, Comp
710356 SCR-MC 10-32 x .62
710357 SCR-MC 10-32 x .75
800187PTD Gulper Nozzle
800217 Fibre Shoe Rear
800218 Fibre Shoe Front

I

J

K

800108 14” Fibre Tool Complete
710530 Screw 8/32 x 1/2 Brass
800003MCH Fibre Shod
800178PTD Tool Casting

800038 6” Tool Squeegee, Complete
800029 Bristle Insert Replacement

800109 14” Squeegee, Comp
710330 SCR-SC 8-32 x .62
800121 14” Retaining Strip
800178PTD Casting, Tool MCH
800239 Blade Squeegee Wide
800240 Blade Squeegee Narrow

4