Wi-Fi Smart Dimmer Switch
• MS10W •
Part 1. Installation
Wiring Instructions - A Few Quick Reminders
A quick note before we give out the wiring schematics. Please do not
try installing this device if you are unsure of how electrical circuits
operate within your home. As exciting as it is to have a smart switch
installed, it can be dangerous and even life-threatening if you do not
install this correctly. Please consult a qualified electrician if
necessary. With that said, here are a few other warnings we’d like to
point out for your safety:
TIPS:
You can break off one or both sides
You can break off one or both sides of
the scored tabs on the front yoke if
installing the In-wall smart switch in
multiple gang boxes. This does not
affect the electrical rating of the smart
switch.
Specifications:
Power: 120VAC, 60Hz
Wireless Frequency: 2.4GHz
Wireless Standard: IEEE802.11b/g/n
Maximum Load:
500 W incandescent, 150W LED
• Switch x1
• wiring x1
• screws x2
• Faceplate x1
1. Tools
Please prepare a flat head screwdriver, a
wire stripper and a voltmeter. Just in case
you might need them.
2. Turn off circuit breaker
Find your light control in your circuit breaker and turn it off. Make
sure the power is off by flipping your switch several times.
3. Detach old switch
Unscrew the top and bottom screws of the switch to detach it from
the wall.
IMPORTANT! Verify power is OFF to switch box before continuing.
4. Connection.(Refer to the step above < INSTALL THE WIRES >
5. Turn on the circuit breaker
Turn on your switch’s power from the circuit breaker. Press the switch
several times to check whether it works.
(300W with both sides of heat sink tabs off)
Minimum Load: 5W for LED bulbs
For indoor use.
INSTALL THE WIRES
Ground
Load
Line
LINE (Hot) — Black (connected to power)
NEUTRAL — White
LOAD — Black (connected to lighting)
GROUND — Green/Bare
TRAVELER — Red/Other(only in 3-way installation)
Common
Traveler
Neutral
NOTE:
• Make sure the power supply of the circuit breaker is turned off before connecting.
• Make sure the wall frame contains a neutral line (usually white). If the box on the wall doesn't have neutral wires, try it in another part of
your home or call a professional electrician to stop the switch.
• Make sure the wires are firmly attached to each wire.
• The colors shown in this manual are common colors and may vary in some homes.
Single switch
Line
Neutral
Ground
Line
Neutral
Ground
From source
From source
3-Way switch option 1
Neutral
Line
Ground
Tapx1( Top rocker) : turn on the light
(the last brightness level)
Press and hold (Top rocker): add brightness
Tapx1(bottom rocker) : turn off the light
Press and hold (bottom rocker) : reduce brightness.
Led Indicator Status:
LED(Orange)
Blink rapidly
Blink slowly
Air-Gap Switch:
Pull out for Bulb replacement
Push back for normal use.
ON
OFF
Part 2. Manual Control
SWITCH
Power OFF
Power ON
Ready for default
configuration mode
Ready for AP(Access Point)
configuration mode
OPERATION GUIDE
Adding your device to Wi-Fi network:
Tapx3(Top or bottom rocker) then hold 10s until the Wi-Fi
status LED blinks rapidly to initiate App-configured Mode.
NOTE: Solid 10s & Flash 1 time: Operation again, Until success.
If you need to reset the device ( Factory setting)
Tapx3(Top or bottom rocker) then hold 10s , The LED
indicator will flash to confirm reset successfully.
NOTE: All previously recorded activity and custom settings
will be erased from the device’s memory.
From source From source
3-Way switch option 2
From source From source
None-connection
Line
Neutral
Ground
Line
Neutral
Ground
Line
Neutral
Ground
Part 3. APP Connection
QR code Smart Life
1. Please scan the QR code to download the application
“Smart Life”.
2. If you cannot download the Smart Life app, please search
“Smart Life” on Google Play (for Android phone) or Apple
Store (for iOS phone) to download.
Aer you download the Smart Life App and register a new account,
please follow the instructions below to set up your smart switch.
3. The smart switch can be also used with Amazon Echo
and Google Home. Please scan the QR code below and
follow the instructions if you have any trouble pairing
with them.
Amazon-Echo Google-Home
1
Tap ‘+’ to add a device in your app
(Our products only support 2.4GHz
Wi-Fi network.）
2
Select
Smart Lighting
-Lighting Devices
B
7
Click the new smart
switch you just added
and you can start using
it now.
C
Tap here to turn
on/off the switch
• Tap “ A ” to turn on/off the light.
• Tap “ B ” to adjust the brightness of the light.
• Tap “ C ” to set a timer to the switch.
AB C
Remove Device
FCC
This device complies with part 15 of the FCC and Industry Canada
license-exempt RSS standard(s). Operation is subjected to the
following two conditions:
(1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference
that may cause undesired operation.
FCC NOTE: The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate
the equipment.
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help
NOTE: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be deter-
mined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following
measures:
Important note: To comply with the FCC RF exposure compliance
requirements, no change to the antenna or the device is permitted.
Any change to the antenna or the device could result in the device
exceeding the RF exposure requirements and void user’s authority
to operate the device.
3
Press the switch 3 times
and hold for 10s at forth
press. LED indicator blinks
rapidly.
4
Enter the Wi-Fi Password
(Your phone should have
connected to the same
Wi-Fi first).
Note:
1)Please operate quickly when LED indicator blinks rapidly.
2)Complete standard operation within 30s When indicator
flash rapidly.
3) Flashing slowly enters AP Mode.
(select “AP Mode” follow the default procedure)
6
5
Wait for the app to
connect to your Wi-Fi
until it’s 100%
Edit the name of your
new smart switch!
Possible Problem Possible Cause Solution
• Unable to connect with the phone
• The light bulb blinks when the
switch turn it off
• Cannot turn the switch on/off
manually
• The switch is not work with APP
control
• The switch cannot connected to
the application
The switch has been connected with
other Wi-Fi.
There is a leakage of electricity or the
bulb does not close with the switch
1. Incorrect wiring
2. No electricity
3. The bulb is broken or incompatible
1. Network delay or disconnect
2. The phone refuses your permission
3. The switch out of the order
1. Enter wrong Wi-Fi password
2. Weak Wi-Fi signal
3. Unable to connect to Wi-Fi
Tap the switch 3 times and hold for 10s. LED
indicator blinks rapidly.
Rewire the switch or replace the bulb.
• Make sure the switch wiring is correct
• Inspecting circuit breakers; Make sure the
power supply is restored
• change a light bulb
• Check your network connectivity, The
switch needs to be reconnected
• Grant permission on your phone settings
• Manually switch on to check the switch
• Enter the correct Wi-Fi password
• Check Wi-Fi signal
• Confirm Your Wi-Fi is 2.4G Hz
CAUTION - PLEASE READ!
This device (MS10W) is intended for installation in accordance with
the National Electric Code and local regulations in the United States,
or the Canadian Electrical Code and local regulations in Canada. If
you are unsure or uncomfortable about performing this installation
consult a qualified electrician.
WARNING - SHOCK HAZARD
TURN OFF THE POWER to the circuit for the switch and lighting
fixture at the service panel (circuit breaker) prior to installation.
ALL WIRING CONNECTIONS MUST BE MADE WITH THE POWER
OFF to avoid personal injury and/or damage to the switch.
OTHER WARNINGS
Risk of Fire
Risk of Electrical Shock
Risk of Burns
WARRANTY
Our Products warrants this product to be free from manufacturing
defects for a period of one year from the original date of consumer
purchase. This warranty is limited to the repair or replacement of
this product only and does not extend to consequential or incidental
damage to other products that may be used with this product. This
warranty is in lieu of all other warranties, expressed or implied.
Some states do not allow limitations on how long an implied
warranty lasts or permit the exclusion or limitation of incidental or
consequential damage, so the above limitations may not apply to
you. This warranty gives you specific rights, and you may also have
other rights which vary from state to state.
We are always here for you:
ask@minoston.com
V2.0
Loading...