Minka Group F853-WH User Manual

U.S. Patent(s) Pending

This product is protected by United States Federal and/or State Law, including Patent, Trademark and/or Copyright laws.
Manual design and all elements of manual design are protected by U.S. Fede

ral and/or State Law, including Patent, Trademark and/or Copyright Laws.

warranty is for one (1) year from the date of purchase from an authorized Minka-Aire dealer.
This warranty is only valid to the original purchaser or user against all defects in material and workmanship (light bulbs
excluded) for one (1) full year. Additionally, Minka-Aire warrants the motor only for the lifetime of the Minka Aire ceiling
fan (excluding wall controls and electrical components), to the original purchaser or user.

The warranty is voided with the use of any non- Minka-Aire electrical devices, E.g., wall controls or electrical dimmer switches, etc...
The warranty is void once the original purchaser or user ceases to own the fan or the fan is moved from its original point of installation.
The warranty is void with the use of any hanger bracket (non-Minka Aire or non-fan specific) other than the hanger bracket supplied & installed
with this specific fan.

Warranty Service Information

To obtain warranty servic during the warranty period, the purchaser should return the fan with the sales receipt to
purchase. The authorized Minka-Aire dealer, at its sole discretion, will either repair or replace the fan after verifying the

®

claim. Replacement is subject to availability of the same model. If the model is unavailable it will be replaced by one of equ
warranty; the original purchaser or user is responsible for the cost of removal and reinstallation of repaired or replacement

To obtain the name of the Minka-Aire authorized dealer nearest you call the Minka-Aire customer care department at 1-800-307-3267, or
contact Minka-Aire through www.minkagroup.net and write to: “Ask Mr. Minka” to answer any questions or if you require assista

®

®

Date Purchased Store Purchased Model Number

®

F853

Serial Number

the original place of

legitimacy of the warranty

al value. This is a limited

product.

nce.

SAFETY FIRST 1

PACKAGE CONTENTS 2

IN INSTALLATION 3

BEG

ING THE FAN 4

HANG

ELECTRI

CAL CONNECTIONS 5

ATTACHING THE FAN BLADES 7

ATTACHING THE BOTTOM CAP AND RING 8

ATING THE REMOTE CONTROL/WALL CONTROL 9

OPER

MAINTENANCE 10

TROUBLESHO

OTING 11

CONTENTS

FINISHING THE INSTALLATION 6

1151W. Bradford Court, Corona CA 92882 For Customer Assistance Call: 1-800-307-3267

SPECIFICATIONS 12

1. Before you begin installing the fan, shut power off at the circuit breaker of the fuse box.

2. Be cautious! Read all instructions and safety information before installing your new fan. Review accompanying assembly diagrams.

3. Make sure that all electrical connections comply with local codes, ordinances, or National Electrical Codes. Hire a qualified electrician or consult a
do-it-yourself wiring handbook if you are unfamiliar with installing electrical wiring.

4. Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from
the floor and 18 inches from the tip of the blades to the wall.

5. NOTE: THIS CEILING FAN EXCEEDS THE MAXIMUM WEIGHT SPECIFIED BY UL FOR HANGING FROM A STANDARD OUTLET BOX. SPECIAL
REINFORCEMENT OF THE CEILING IS REQUIRED FOR INSTALLATION.

6. CAUTION: Use the wood screws provided for fan installation. The wood screws must go through the outlet box via the knock outs and secured
directly to the building joist.

7. After you install the fan, make sure that all mounting components are secured to prevent the fan from falling.

8. Do not insert anything into the fan blades while the fan is operating.

9. Turn the fan off and wait for the blades to stop completely before cleaning or performing any maintenance.

1

SAFETY FIRST

NOTE:The important safeguards and instructions appearing in this manual are not meant to cover all possible conditions and situations that may
occur. It must be understood that common sense, caution and care are factors which can not be built into this product. These factors must be
supplied by the person (s) installing, caring for and operating the unit.

NOTE: READ AND SAVE ALL INSTRUCTIONS!

WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR OTHER PERSONAL INJURY. MOUNT FAN DIRECTLY TO THE BUILDING JOIST USING TH

WOOD SCREWS AND WASHERS PROVIDED WITH THE FAN. THE WOOD SCREWS MUST GO THROUGH THE OUTLET BOX VIA THE KNOCK
OUTS. CONSULT A QUALIFIED ELECTRICIAN IF IN DOUBT.

TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE BLADE HOLDERS WHILE INSTALLING, BALANCING THE BLADES, O
CLEANING THE FAN. DO NOT INSERT FOREIGN OBJECTS BETWEEN ROTATING FAN BLADES.

TO REDUCE THE RISK OF FIRE OR ELECTRONIC SHOCK, THIS FAN ONLY CAN USE THIS FAN ONLY CAN USE 120DC-3-1 RECEIVER AND RC500
REMOTE CONTROL ONLY.

E

R

2

PACKAGE CONTENTS

1. Fan motor/housing

ass'y

2. Canopy

3. Fan blade

4. Coupling cover

5. Canopy cover

6. Hanger bracket

7. Bottom cap

8. Ring

9. Standard 6"downrod

assembly

10. Minimun 3-1/2" length

downrod (for close to
ceiling mounting only)

11. Remote control
A. Blade attachment hardware:
#10-24x12mm hex screw
(7pcs)
B. Mounting Hardware:
#8-32x38mm screw(2pcs)
#10x38mm wood screw
(2pcs)
3/16"(Ø5.2x8.4x1.0mm)
spring washer(2pcs)
Ø5x14x1mm flat washer
(2pcs)

5/32"(Ø4.4x9.4x0.5-1.0mm

-10 tooth) wash(2 pcs)
C. #8-32x7mm texture hex
screws (7pcs)
D. M3 L hex wrentch(1pcs)
E. Wire nut(3pcs)
G. Balance kit
H. Glove
I. Clean cloth