Milwaukee Instruments MW11 User Manual

WARRANTY:

Milwaukee

This instrument is warranted from all defects in materials and manufacturing for
a period of two years from the date of purchase.
If during this period, the repair or replacement of parts is required, where the
damage is not due to negligence or erroneous operation by the user, please return
the parts to either dealer or our office and the repair will be effected free of charge.
Note: We reserve the right to modify the design, construction and appearance

of our products without advance notice.

SPECIFICATIONS:

MW 11

RANGE 0.00 to 3.50 ppm
RESOLUTION 0.01 ppm
ACCURACY ±0.03 ppm ±3% of reading @ 25 °C
TYPICAL EMC DEV. ±0.01 ppm
LIGHT SOURCE Light Emitting Diode @ 525 nm
LIGHT DETECTOR Silicon Photocell
METHOD Adaptation of USEPA method 330.5. The reaction

between total chlorine and the DPD reagent

causes a pink tint in the sample.

ENVIRONMENT 0 to 50°C (32 to 122 °F)

max. 95% RH non-condensing

BATTERY TYPE 1 x 1.5V AAA
AUTO-SHUT OFF After 2 minutes of non-use
DIMENSIONS 81.5 x 61 x 37.5 mm (3.2 x 2.4 x 1.5”)
WEIGHT 64 g (2.25 oz.)

OPTIONAL ACCESSORIES:

Reagent Sets

2720216 Total Chlorine powder reagent, 25 pcs.

Other Accessories

3000100 Glass cuvettes with caps (2 pcs)
3000200 Tissue fow wiping cuvettes (2 pcs)
3000300 1.5V AAA batteries (4 pcs)

Milwaukee

USER MANUALT

TOTAL CHLORINE

MODEL: MW11

ISTMW11 08/10

PRELIMINARY EXAMINATION:

Please examine this product carefully. Make sure that the
instrument is not damaged. If any damage occured during
shipment, please notify your Dealer.
Each MW 11 meter is supplied complete with:

• Two Sample Cuvettes and Caps

• Six powder reagents for Total Chlorine

• 1 x 1.5V AAA Battery

• Instruction Manual

FUNCTIONAL DESCRIPTION:

1. Dust cover

2. Cuvette with cap

3. Cuvette holder

4. Liquid Crystal Display

5. Button

OPERATION:

• Turn the meter on by pressing the
button. After all the segments are dis­played, “C.1”, “Add” appears with
“Press” blinking, the meter is ready.

• Fill the cuvette with 10 mL of unre­acted sample and replace the cap.
Place the cuvette into the meter and
close the meter’s cap.

• Press the button. When the display
shows “Add”, “C.2” with “Press” blink­ing the meter is zeroed.

10 mL

• Remove the cuvette, open it and add
the content of one packet of 2720216
reagent. Replace the cap and shake
gently for 20 seconds. Replace the
cuvette into the meter.

• Wait for 2 minutes and 30 seconds
and then press the button or press
and hold the button until the timer is
displayed on the LCD.

• The instrument directly displays the
concentration of total chlorine in ppm.
The meter automatically turns off after
2 minutes.

BATTERY REPLACEMENT:

To save the battery, the instrument shuts down after 2 minutes
of non-use. One fresh battery lasts for a minimum of 5000
measurements, depending on the light level. When the battery
capacity is under 10 % “bAt” appears on the LCD at start-up.
If the battery is empty and accurate measurements can’t be
taken any more, the instrument shows “bAd” then ”bAt” each
for 1 second and turns off. To restart the instrument, the
battery must be replaced with a fresh one.
To replace the instrument’s battery, follow the steps:

• Turn the instrument off by holding the button until the meter

shuts off.

• Turn the instrument

upside down and
remove the battery cover
with a screwdriver.

• Remove the battery from

its location and replace
it with a fresh one.

• Insert the battery cover

and replace the screw
with a screwdriver.