Cat. No.
0,&$9&
M12™ M-SPECTOR FLEX™ INSPECTION CAMERA
OPERATOR'S MANUAL
To reduce the risk of injury, user must read and understand operator's manual.
WARNING
2
GENERAL POWER TOOL
SAFETY WARNINGS
WARNING
Read all safety warnings, instructions, illustrations and specica-
tions provided with this power tool. Failure to
follow all instructions listed below may result in
electric shock, re and/or serious injury. Save all
warnings and instructions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-oper-
ated (cordless) power tool.
WORK AREA SAFETY
• Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
• Do not operate power tools in explosive atmo-
spheres, such as in the presence of ammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
• Keep children and bystanders away while operating a power tool. Distractions can cause you to lose
control.
ELECTRICAL SAFETY
• Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodied plugs and matching outlets will
reduce risk of electric shock.
• Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
• Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the
risk of electric shock.
• Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase
the risk of electric shock.
• When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
• If operating a power tool in a damp location is
unavoidable, use a ground fault circuit interrupter
(GFCI) protected supply. Use of an GFCI reduces
the risk of electric shock.
PERSONAL SAFETY
• Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the inuence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
• Use personal protective equipment. Always
wear eye protection. Protective equipment such
as a dust mask, non-skid safety shoes, hard hat or
hearing protection used for appropriate conditions
will reduce personal injuries.
• Prevent unintentional starting. Ensure the switch
is in the off-position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your nger on
the switch or energizing power tools that have the
switch on invites accidents.
• Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
• Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or
jewelry. Keep your hair and clothing away from
moving parts. Loose clothes, jewelry or long hair
can be caught in moving parts.
• If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
• Do not let familiarity gained from frequent use
of tools allow you to become complacent and
ignore tool safety principles. A careless action can
cause severe injury within a fraction of a second.
POWER TOOL USE AND CARE
• Do not force the power tool. Use the correct power
tool for your application. The correct power tool
will do the job better and safer at the rate for which
it was designed.
• Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
• Disconnect the plug from the power source and/
or remove the battery pack, if detachable, from
the power tool before making any adjustments,
changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of
starting the power tool accidentally.
• Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the
power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands
of untrained users.
• Maintain power tools and accessories. Check
for misalignment or binding of moving parts,
breakage of parts and any other condition that
may affect the power tool’s operation. If damaged,
have the power tool repaired before use. Many
accidents are caused by poorly maintained power
tools.
• Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
• Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions and
the work to be performed. Use of the power tool
for operations different from those intended could
result in a hazardous situation.
• Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
BATTERY TOOL USE AND CARE
• Recharge only with the charger specied by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of re when used
with another battery pack.
• Use power tools only with specically designated
battery packs. Use of any other battery packs may
create a risk of injury and re.
• When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects,
that can make a connection from one terminal
3
to another. Shorting the battery terminals together
may cause burns or a re.
• Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation
or burns.
• Do not use a battery pack or tool that is damaged or modied. Damaged or modied batteries
may exhibit unpredictable behavior resulting in re,
explosion or risk of injury.
• Do not expose a battery pack or tool to re or
excessive temperature. Exposure to re or temperature above 130°C (265°F) may cause explosion.
• Follow all charging instructions and do not charge
the battery pack or tool outside the temperature
range specied in the instructions. Charging im-
properly or at temperatures outside the specied range
may damage the battery and increase the risk of re.
SERVICE
• Have your power tool serviced by a qualied
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
• Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorised service providers.
SPECIFIC SAFETY RULES FOR
MULTIMEDIA CAMERA
• Maintain labels and nameplates. These carry
important information. If unreadable or missing,
contact a MILWAUKEE® service facility for a
replacement.
Federal
Communications
Commission
WARNING
This is a class
A product. In
a domestic environment this
product may cause radio interference in which case
the user may be required to take adequate measures.
This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference when the equipment is operated in a
commercial environment. This equipment generates
uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a
residential area is likely to cause harmful interference
in which case the user will be required to correct the
interference at his own expense.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
SPECIFICATIONS
Cat. No. ..........................................M12ICAV3-90C
Volts.............................................................. 12 DC
Battery Type .................................................M12™
Charger Type................................................M12™
Memory Card ......................................................SD
Interface Cable ...................................... Micro USB
SYMBOLOGY
Volts
Direct Current
User Must Read Operator's Manual
Wear Eye Protection
To Prevent Electric Shock, Do Not
Allow Product to Contact Live
Electrical Parts
Regulatory Compliance Mark
(RCM). Product meets applicable
regulatory requirements.
Federal Communications Commission
Similarly in Australia and New Zealand this product
complies to ACMA EMC requirements.
FUNCTIONAL DESCRIPTION
11
12
1
2
3
8
6
7
5
4
9
10
21
22
23
PIVOTVIEW™ Cable
21. Pivot joint
22. Pivot knob
23. Release buttons
1/4 - 20 UNC Threaded accessory bay
(back of Display)
1. Camera
2. Camera LED
3. Cable
4. Socket sleeve
5. Display
6. Media cover
8. Handle power button
9. Handle
10. Trigger
11. LED brightness dial
12. Speaker
13. Power button
14. Picture / Movie toggle
15. Arrow buttons
16. OK button
17. Playback button
18. Setting button
19.
20.
Reset button (back of Display)
7. Microphone
13
14
15
16
17
18
19
20
4
Settings
To enter the settings menu, turn on the tool and
press the Settings button. Use the
◄►▲▼
buttons
to move through the setting menu.
MENU SELECTIONS
____________
MICROPHONE ON/OFF
LCD BRIGHTNESS LOW/MEDIUM/HIGH
DATE MM/DD/YY
TIME HR/MIN AM/PM
LANGUAGE MULTIPLE SELECTIONS
DELETE ALL CANCEL/DELETE ALL
VERSION Display the software version.
OPERATION
WARNING
To reduce the risk of injury, always
wear safety goggles or glasses
with side shields.
Always remove battery pack before changing
accessories or making adjustments.
Turning On/Off
When the display is docked on the handle, press
either Power
button to turn the tool on. Press and
hold either Power
button to turn the tool off.
When the display and handle are separated, use the
individual power buttons to turn each piece on and off.
Fuel Gauge
When the display is docked on the handle, the
M12™ battery pack fuel gauge is displayed in the
upper right corner.
When the display is undocked from the handle, two
fuel gauges are displayed. The left gauge shows the
remaining charge of the display's internal battery.
The right gauge shows the remaining charge of the
M12™ battery pack. Each block in the fuel gauges
represents approximately 1/4
of the battery's life.
WARNING
To reduce the risk of explosion,
electric shock and property dam-
age, always check the work area before beginning
a job. Do not allow cable to contact electrical,
chemical, or moving hazards.
Behind walls: Shut off circuit breakers to the
entire area.
Inside Pipes: Ensure there is no electrical charge
to the pipes before beginning inspection. Do not
allow liquid to ow down cable and into tool.
Auto use: Turn off the engine and allow to cool
before beginning inspection. Do not allow the
visual inspection camera or cable to contact oil,
gas, or other corrosive materials.
CAUTION
To reduce the risk of damage to the
tool, do not use excessive force or
“kink” the cable. Do not use in areas where visual inspection camera and cable will contact
corrosive or oily substances.
Do not use the cable to clear clogs or move ob-
structions. This is not a drain cleaner!
ASSEMBLY
WARNING
Recharge only with the charger
specied for the battery. For specic charging instructions, read the operator’s
manual supplied with your charger and battery.
Removing/Inserting the Battery
To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
WARNING
Always remove battery pack before
changing or removing accessories.
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
Charging the Display
When the display and handle are connected, the bat-
tery pack will power both the handle and the display.
When separated, the display runs off of an internal re-
chargeable battery. To recharge the display, connect
it to the handle/battery pack, or to a power source via
USB cable. Always store the display docked on the
handle. If the display shuts down due to low power,
recharge for at least 30 minutes before use.
WARNING
Only use accessories specically
recommended for this tool. Others
may be hazardous.
Connecting the Cable
1. Slide back the socket sleeve.
2. Insert the cable into the socket.
3. Rotate the cable until it is fully seated into the
socket.
4. Slide the sleeve over the connection. Tighten the
sleeve securely.
Connecting the PIVOTVIEW™ Cable
(Some Models or as an Accessory)
1. Rotate the pivot knob to determine the orientation
needed for the movement. The pivot head rotates
up to 270º on one plane.
2. Snap the PIVOTVIEW™ Cable over the socket. It
must line up in one of four 90° positions.
3. To remove, press the release buttons and pull
away from the tool.
Inserting/Removing the Memory Card
The number of images/videos that can be saved is
based on the size of the memory card.
1. Open the protective cover to
access the memory card slot.
2. Slide the memory card into the
slot, the top of the card should
face away from the LCD screen.
Press in the card securely. It
should click in place.
3. Close the protective cover.
4. To remove the memory card,
press it in and release. It will pop out.
Note: To save images/videos to the memory card, it
must not be “locked” with the write-protection tab in
the lower position.
NOTE: If you are unable to view the videos on your
computer it may be because your computer is miss-
ing the DIVX or XVID codec. The AVI le is recorded
in MPEG4 format and your computer needs a DIVX
or XVID codec to decode and play it. Download the
appropriate codec to view the images/videos.
Downloading to a Computer
Power on the display. Insert the USB cable into
the port on the side of the display. Connect the
USB end into the USB port on your computer.
5
Using the PIVOTVIEW™ Cable
(Some Models or as an Accessory)
1.
2. Carefully feed cable into desired area.
3.
Turn the pivot knob to rotate the head up to 270º
on a single plane.
4. If the desired view is not achieved, press the
release buttons and rotate the pivot cable 90°.
Reattach to the socket. Bend or manipulate the
cable as needed.
Taking Images/Videos
Use the Image/Video button to toggle between
taking images or videos. The icon of the selected
mode is displayed in the upper left corner of the
display.
1.
2. Use the ▲▼ buttons to zoom in or out on the
image.
3. Use the ◄► buttons to rotate the image in 90°
increments.
4. Use the LED brightness dial to increase/decrease
the light.
5. To take an image or begin a video, press the OK
button or pull the trigger.
6. To end the video, press OK or pull the trigger again.
7. To save the image/video, press OK or pull the
trigger. The image/video is saved onto the memory
card. Or, use the ◄► buttons to select Cancel.
8. NOTE: During a video recording, sound is also
recorded at the display if the MICROPHONE is
ON in Settings.
Review
Press the Review button to view the saved im
-
ages/videos.
1. Use the ◄► buttons to move through the stored
images/videos.
2. Press the OK button to select an image/video.
3. Use the ▲▼ buttons to select one of the following:
EDIT Zoom or rotate an image. Use the ▲▼
buttons to zoom. Use the ◄► buttons
to rotate in 90° increments.
PLAY Play back a video. Use OK to Pause/
Play. Use the ◄► buttons to Rewind/
Fast Forward.
DELETE Permanently delete an image/video.
FLAG
DONE Return to Review screen
Reset Button
Use the reset button to restart the unit.
MAINTENANCE
WARNING
To reduce the risk of injury, always
unplug the charger and remove the
battery pack from the charger or tool before
performing any maintenance. Never disassemble
the tool, battery pack or charger. Contact a
service facility for ALL repairs.
Maintaining Tool
Keep your tool, battery pack and charger in good
repair by adopting a regular maintenance program.
Inspect your tool for issues such as undue noise,
misalignment or binding of moving parts, breakage of
parts, or any other condition that may affect the tool
operation. Return the tool, battery pack, and charger
to a MILWAUKEE
®
service facility for repair. After six
months to one year, depending on use, return the
tool, battery pack and charger to a MILWAUKEE®
service facility for inspection.
If the tool does not start or operate at full power with
a fully charged battery pack, clean the contacts on
the battery pack. If the tool still does not work properly, return the tool, charger and battery pack, to a
MILWAUKEE® service facility for repairs.
WARNING
To reduce the risk of personal injury and damage, never immerse
Cleaning
Repairs
For repairs, return the tool, battery pack and charger
to the nearest service centre.
ACCESSORIES
WARNING
Use only recommended accessories. Others may be hazardous.
For a complete listing of accessories, go online to
To separate the display from the handle grasp each
part firmly and slide the display away from the
battery pack. To reconnect, slide handle and display
together.
NOTE: The error message "NO IMAGE SIGNAL" is
displayed if the handle is not powered on, the
handle is out of
range of the display (approximately
4.57M (15')) or the cable is not fully connected to the
handle. Also, interference may occur when multiple
tools are in use in close proximity.
Using the Handle and Display
Flag an image/video for future use. An
"F" is added to the front of the file
name for ease of locating when
connected to a computer.
Adjust the cable to best fit the opening. After
checking the workspace for hazards, insert the
cable.
your tool, battery pack or charger in liquid or
allow a liquid to flow inside them.
www.milwaukeetools.com.au/
www.milwaukeetools.co.nz or contact a distributor.
M-Spector FLEX™ 1M (3') Inspection Camera
Cable
Cat. No. 48530150
M-Spector FLEX™ 2.74M (9') Inspection Camera
Cable
Cat. No. 48530151
M-Spector FLEX™ 1M (3') Inspection Camera
Cable with PIVOTVIEW™
Cat. No. 48530155
Clean dust and debris from vents. Keep handles
clean, dry and free of oil or grease. Use only mild
soap and a damp cloth to clean, since certain
cleaning agents and solvents are harmful to
plastics and other insulated parts. Some of these
include gasoline, turpentine, lacquer thinner, paint
thinner, chlorinated cleaning solvents, ammonia
and household detergents containing ammonia.
Never use flammable or combustible solvents
around tools.
Install in the desired orientation according to
"Connecting the Cable".
MILWAUKEE
®
For a list of MILWAUKEE® dealers, guarantee or service agents please contact MILWAUKEE
®
Customer Service or visit our website.
(Australia Toll Free Telephone Number 1300 361 505)
(New Zealand Toll Free Telephone Number 0800 279 624)
or visit www.milwaukeetools.com.au / www.milwaukeetools.co.nz.
Milwaukee Electric Tool Corporation
13135 West Lisbon Road, Brookfield, Wisconsin U.S.A. 53005
Milwaukee Electric Tool Corporation (Australia)
Techtronic Industries (Australia) Pty. Ltd.
Rowville, Victoria, Australia, 3178
Milwaukee Electric Tool Corporation (New Zealand)
Techtronic Industries (New Zealand) Pty. Ltd.
Mangere, Auckland, New Zealand, 2022
Professionally made in China for Milwaukee Electric Tool Corporation
WARRANTY - AUSTRALIA and NEW ZEALAND
SERVICE - AUSTRALIA and NEW ZEALAND
MILWAUKEE®prides itself in producing a premium quality product that is Nothing But Heavy Duty®.
Your satisfaction with our products is very important to us! If you encounter any problems with the
operation of this tool, please contact your authorised MILWAUKEE® dealer.
Please refer to Australian and New Zealand warranty supplied with tool. This warranty applies only to
product sold in Australia and New Zealand.
Loading...