Milwaukee DescriptionDescription Service Parts List
EXAMPLE:
00
0
Component Parts (Small #)
Are Included When Ordering
The Assembly (Large #).
SERVICE PARTS LIST
SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS
M18™ FUEL™ 1/4" Hex Impact Driver
CATALOG NO. 2853-20
48
34
(5x)
STARTING
SERIAL
J57A
BULLETIN NO.
54-26-2890
REVISED BULLETIN
WIRING INSTRUCTION
See Pages 2
60
DATE
Dec. 2020
36
36 37
56
59
53
48
23
23
39
61
2 3 4 5 6
51
7 8 9 10 11
8
7
6
4
2
1
5
3
58
39
35
(2x)
62
9
6 10
11
52
11
10
(2x)
55
54
43
37
34
(4x)
57
39
39
FIG. PART NO. DESCRIPTION OF PART NO. REQ.
1 31-12-0203 Rubber Nose Cap (1)
2 34-60-0005 Retaining Ring (1)
3 45-88-2026 Washer (1)
4 40-50-0056 Spring (1)
5 42-76-0019 Sleeve (1)
6 --------------- Spring (See Fig. #62) (1)
7 45-88-1547 Washer (1)
8 --------------- Front Gear Case (1)
9 45-88-2653 Front Gear Case Washer (1)
10 02-02-1100 Steel Ball (2)
11 42-06-7070 1/4" Hex Anvil (1)
23 34-40-0596 O-Ring (1)
34 06-82-6351 M3 x 16mm Pan Hd. ST T-10 Screw (9)
35 06-82-2367 M3 x 38mm Pan Hd. ST T-10 Screw (2)
36 --------------- Right Housing Halve - Cover (1)
37 --------------- Left Housing Halve - Support (1)
39 06-82-2500 6-32 Pan Hd. Slotted T-15 Mach. Scr. (2)
43 45-24-0261 Forward/Reverse Shuttle (1)
48 12-20-1217 Service Nameplate (1)
51 14-30-6245 Gear Case Assembly (1)
52 14-30-2806 Impacting Assembly (1)
53 44-66-2681 End Cap Assembly (1)
54 14-20-2821 Electronics Assembly (1)
55 16-01-2831 Rotor/Back Cap Assembly (1)
56 31-44-2866 Housing Assembly (1)
57 42-70-0950 Belt Clip Kit (1)
58 43-72-0950 Bit Holder Kit (1)
FIG. PART NO. DESCRIPTION OF PART NO. REQ.
59 45-24-1301 Speed Selector Assembly (1)
60 42-55-0036 Blow Molded Carrying Case (1)
61 49-16-2853 Rubber Boot, Accessory (1)
62 42-06-2560 Anvil, Service Kit (1)
MILWAUKEE TOOL l www.milwaukeetool.com
13135 W. Lisbon Road, Brookeld, WI 53005
Drwg. 2
Rotor/Back Cap
Assembly
Stator Assembly
On-Off Switch
Potted Circuit Board
Assembly
Route the LED wires and ground wire
from PCBA behind switch and through
wire channels/traps as shown. Seat
LED module squarely in cavity of left
housing halve. With LED in place,
install ground terminal over screw boss.
Place switch firmly and squarely into
corresponding cavity of left housing
halve.
Battery
Connector
Block Assy.
Speed Selector Assembly Ground Terminal LED Assembly
As an aid to reassembly, take note of wire routings and position
in wire guides and traps while dismantling tool. Route wires into
wire traps and channels as shown.
Be sure to place wires down into wire traps, being sure to
remove any wire slack while routing.
Be sure components of electronics assembly are seated firmly
and squarely in the corresponding cavity of handle support.
Be sure there are no interferences when installing handle
cover over handle support. Watch for pinched wires.
Check for proper functionality of slide buttons and speed dial
prior to installing battery.