Milwaukee Tool 8988-20 User Manual [en, es, fr]
Cat. No.
No de cat.
8988-20
OPERATOR'S MANUAL
MANUEL de L'UTILISATEUR
MANUAL del OPERADOR
VARIABLE TEMP. HEAT GUN
PISTOLET THERMIQUE À TEMPÉRATURE VARIABLE
PISTOLA DE CALOR DE TEMPERATURA VARIABLE
TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND OPERATOR'S
MANUAL.
AFIN DE RÉDUIRE LE RISQUE DE BLESSURES, L'UTILISATEUR DOIT LIRE ET BIEN
COMPRENDRE LE MANUEL DE L'UTILISATEUR.
PARA REDUCIR EL RIESGO DE LESIONES, EL USUARIO DEBE LEER Y ENTENDER EL
MANUAL DEL OPERADOR.
GENERAL POWER TOOL SAFETY WARNINGS
WARNING READ ALL SAFETY WARNINGS AND ALL INSTRUCTIONS.
Failure to follow the warnings and instructions may result in electric shock, fi re and/or
serious injury. Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
• Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
• Do not operate power tools in explosive atmospheres, such as in the presence of fl ammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
• Keep children and bystanders away while operating a power tool. Distractions can cause you to lose
control.
ELECTRICAL SAFETY
WORK AREA SAFETY
• Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools. Un-
modifi ed plugs and matching outlets will reduce risk
of electric shock.
• Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
• Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the
risk of electric shock.
• Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk
of electric shock.
• When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric
shock.
• If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
PERSONAL SAFETY
• Stay alert, watch what you are doing and use common sense when operating a power tool. Do not
use a power tool while you are tired or under the
infl uence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result in
serious personal injury.
• Use personal protective equipment. Always wear
eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce
personal injuries.
• Prevent unintentional starting. Ensure the switch
is in the off-position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your fi nger on the
switch or energising power tools that have the switch
on invites accidents.
• Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to
a rotating part of the power tool may result in personal
injury.
• Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power
tool in unexpected situations.
• Dress properly. Do not wear loose clothing or
jewellery. Keep your hair , clothing and gloves away
from moving parts. Loose clothes, jewellery or long
hair can be caught in moving parts.
• If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection
can reduce dust-related hazards.
POWER TOOL USE AND CARE
• Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
• Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
• Disconnect the plug from the power source and/or
the battery pack from the power tool before making
any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
• Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool
or these instructions to operate the power tool. Pow-
er tools are dangerous in the hands of untrained users.
• Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and
any other condition that may affect the power
tool’s operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
• Use the power tool, accessories and tool bits etc.,
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Use of the power tool for operations
different from those intended could result in a hazardous situation.
SERVICE
• Have your power tool serviced by a qualifi ed repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
IMPORTANT SAFETY INSTRUCTIONS
HEAT GUNS
READ THESE INSTRUCTIONS
• Know your work environment. Hidden areas such
as behind walls, ceilings, fl oors, soffi t boards and other
panels may contain fl ammable materials that may ignite
when using the heat gun in these locations. Ignition of
these materials may not be readily apparent and could
result in property damage and personal injury. Check
these areas before applying heat. If in doubt, use an
alternate method. Pausing or lingering in one spot may
2
ignite the panel or the material behind it. Keep heat
gun moving to avoid excessive temperatures.
• Do not direct the heat gun air airfl ow at clothing,
hair or other body parts. Do not use as a hair dryer.
Heat guns can produce 1150°F (621°C) or more of
fl ameless heat at the nozzle. Contact with the air
stream could result in personal injury.
• Do not use near fl ammable liquids or in explosive
atmospheres, such as in the presence of fumes,
gases or dust. The fl ameless heat from the heat gun
may ignite the dust or fumes. Remove materials or
debris that may become ignited from work area.
• Shield materials around the heated area to prevent
property damage or fi re.
• Keep a fi re extinguisher nearby. Heat guns may
ignite fl ammable materials left in the work area.
• WARNING! Hot Surfaces. Always hold the heat
gun by the plastic enclosure. Do not touch nozzle,
accessory tips or store heat gun until the nozzle
has cooled to room temperature. The metal nozzle
requires approximately 20 minutes to cool before it
can be touched. Contact with the nozzle or accessory
tip could result in personal injury. Place the heat gun
in a clear area away from combustible materials while
cooling to prevent fl ammable materials from igniting.
• Do not cut off airfl ow by placing nozzle too close
to workpiece. Keep intake vents clean and clear of
obstructions. Restricting airfl ow may cause the heat
gun to overheat.
IMPORTANT SAFETY INSTRUCTIONS FOR REMOVING PAINT
WARNING Use extreme care when
stripping paint. Peelings, residue and vapors of
paint may contain lead, which is POISONOUS.
Pre-1977 paint may contain lead and paint
made before 1950 is likely to contain lead.
Hand to mouth contact with paint peelings or
residue from pre-1977 paint may result in lead
ingestion. Exposure to even low levels of lead
can cause irreversible brain and nervous
system damage. Y oung and unborn children are
especially vulnerable to lead poisoning. DO NOT
REMOVE LEAD-BASED PAINT WITH A HEAT
GUN. Before beginning your work, determine
whether the paint you are removing contains
lead. A local health department or a professional
who uses a paint analyzer can check the paint
for lead content. LEAD-BASED PAINT SHOULD
BE REMOVED ONLY BY A PROFESSIONAL.
PERSONS REMOVING PAINT SHOULD
FOLLOW THESE GUIDELINES:
• Work in a well ventilated area. If possible, move
the workpiece outdoors. If working indoors, open windows and place an exhaust fan in a window. Be sure
the fan is moving air from inside to outside. Proper
ventilation will reduce the risk of inhaling chemicals
found in the fumes or dust created by using a heat gun.
• Remove or cover any carpets, rugs, furniture,
clothing, cooking utensils and air ducts to prevent
property damage from the paint peelings.
• Place drop cloths in the work area to catch paint
scrapings. Wear protective clothing such as hats,
extra work shirts and overalls. Paint scrapings may
contain chemicals that are hazardous.
3
• Place the heat gun on a stable, level surface when
not hand held. Use the support pads or support
stand. Place cord in a position that won’t cause the
heat gun to tip over.
• Do not leave the heat gun unattended while running
or cooling down. Inattention invites accidents.
• Store indoors in a dry location. Do not expose to
rain or moisture.
• Do not direct airfl ow directly on glass. The glass
may crack and could result in property damage or
personal injury.
• Maintain labels and nameplates. These carry important information. If unreadable or missing, contact
a MILWAUKEE Service facility for a free replacement.
• WARNING Some dust created by power sanding,
sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth
defects or other reproductive harm. Some examples
of these chemicals are:
• lead from lead-based paint
• crystalline silica from bricks and cement and other
masonry products, and
• arsenic and chromium from chemically-treated lumber .
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to fi lter
out microscopic particles.
• Work in one room at a time. Remove furnishings
or cover them and place in the center of the room.
Seal doorways with drop cloths to seal work area
from the rest of the building.
• Children, pregnant or potentially pregnant
women, and nursing mothers should not be near
work area until all work is completed and work area
is cleaned thoroughly.
• Wear a dust respirator mask or a dual filter
(dust and fume) respirator mask which has been
approved by the Occupational Safety and Health Administration (OSHA), the National Institute of Safety
and Health (NIOSH), or the United States Bureau
of Mines. These masks and replaceable fi lters are
readily available at major hardware stores. Be sure
the mask fi ts. Beards and facial hair may keep masks
from sealing properly. Change fi lters often. DISPOS-
ABLE PAPER MASKS ARE NOT ADEQUATE.
• Use caution when operating the heat gun. Keep
the heat gun moving to prevent excessive temperatures. Excessive heat can cause paint and other
materials to burn and cause fumes, which may be
inhaled by the operator.
• Keep work environment clean. Keep food and
drink away from work area. Wash hands, arms and
face and rinse mouth before eating and drinking. Do
not smoke, or chew gum or tobacco in the work area.
Paint scrapings and dust created from removing
paint may contain chemicals that are hazardous.
• Clean up all paint scraping and dust. DO NOT
SWEEP , DR Y DUST OR V ACUUM. Wet mop fl oors.
Use a wet cloth to clean all walls, sills and other surfaces where paint and dust have accumulated. Use
a high phosphate detergent, trisodium phosphate
(TSP), or a trisodium phosphate substitute to clean
and mop the work area.
• Dispose of paint scrapings properly. Following
each work session, place paint scrapings in a double
plastic bag, close it with tape or twist ties and dispose.
• Remove protective clothing and work shoes
in the work area to avoid transferring dust to
other parts of the building. Wash work clothes
separately. Wipe shoes of f with a wet rag that is then
washed with the work clothes. Wash hair and body
thoroughly with soap and water.
SAVE THESE INSTRUCTIONS
SPECIFICATIONS
Cat. No. Volts AC
8988-20 120 12.5 1500 I
Max.
Amps
Max.
Watts
Switch
Setting Temperature
II
120°F - 1150°F (49°C - 621°C)
III
120°F - 1150°F (49°C - 621°C)
120°F (49°C)
* Cubic feet per minute
TEMPERATURE CONVERSIONS
°C = °F °C = °F °C = °F °C = °F °C = °F °C = °F
38 100 149 300 260 500 371 700 482 900 593 1100
93 200 200 392 300 572 400 752 500 932 600 1112
100 212 204 400 316 600 427 800 538 1000 649 1200
GROUNDING
Grounded tools require a three wire extension cord.
WARNING Improperly connecting the
grounding wire can result in the risk of electric
shock. Check with a qualifi ed electrician if you
are in doubt as to whether the outlet is properly
grounded. Do not modify the plug provided with
the tool. Never remove the grounding prong
from the plug. Do not use the tool if the cord or
plug is damaged. If damaged, have it repaired
by a MILWAUKEE service facility before use.
If the plug will not fi t the outlet, have a proper
outlet installed by a qualifi ed electrician.
Grounded Tools: Tools with Three Prong Plugs
Tools marked “Grounding Required” have a three wire
cord and three prong grounding plug. The plug must be
connected to a properly grounded outlet (See Figure
A). If the tool should electrically malfunction or break
down, grounding provides a low resistance path to
carry electricity away from the user, reducing the risk
of electric shock.
The grounding prong in the plug is connected through
the green wire inside the cord to the grounding system
in the tool. The green wire in the cord must be the only
wire connected to the tool's grounding system and
must never be attached to an electrically “live” terminal.
Your tool must be plugged into an appropriate
outlet, properly installed and grounded in accordance with all codes and ordinances.
The plug and outlet should look like
those in Figure A.
Double Insulated Tools: T ools with T wo Prong Plugs
Tools marked “Double Insulated” do not require
grounding. They have a special double insulation
system which satisfi es OSHA requirements and com-
plies with the applicable standards of
Underwriters Laboratories, Inc., the
Canadian Standard Association and
the National Electrical Code. Double
Insulated tools may be used in either of the 120 volt outlets shown in
Figures B and C.
Fig. A
Fig. B
Double insulated tools can use either a two or three wire
extension cord. As the distance from the supply outlet
increases, you must use a heavier gauge extension
cord. Using extension cords with inadequately sized
wire causes a serious drop in voltage, resulting in loss
of power and possible tool damage. Refer to the table
shown to determine the required minimum wire size.
The smaller the gauge number of the wire, the greater
the capacity of the cord. For example, a 14 gauge cord
can carry a higher current than a 16 gauge cord. When
using more than one extension cord to make up the total
length, be sure each cord contains at least the minimum
wire size required. If you are using one extension cord for
more than one tool, add the nameplate amperes and use
the sum to determine the required minimum wire size.
Guidelines for Using Extension Cords
• If you are using an extension cord outdoors, be sure
• Be sure your extension cord is properly wired and in
• Protect your extension cords from sharp objects,
Fig. C
4
it is marked with the suffi x “W-A” (“W” in Canada) to
indicate that it is acceptable for outdoor use.
good electrical condition. Always replace a damaged
extension cord or have it repaired by a qualifi ed person
before using it.
excessive heat and damp or wet areas.
Nameplate Amps
INSTRUCTIONS FOR FUTURE USE.
EXTENSION CORDS
Recommended Minimum Wire Gauge
For Extension Cords*
0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 16.0
16.1 - 20.0
* Based on limiting the line voltage drop to fi ve volts
at 150% of the rated amperes.
Extension Cord Length
25' 50' 75' 100' 150'
18
18
18
18
16
14
12
10
18
18
16
14
12
10
--
18
18
18
16
14
12
READ AND SAVE ALL
Airfl ow
CFM*
3.6
10.6
17.6
18
16
14
12
10
--
--
16
14
12
12
FUNCTIONAL DESCRIPTION
4
1
2
3
1. Accessory
attachment area
2. Nozzle
3. Front cover
4. Nameplate (on back)
5. Intake vents
6. Handle
7. ON/OFF/Airfl ow switch
8. Support stand bumpers
9. LCD
10. Temperature controls
6
5
7
8
9
10
SYMBOLOGY
Double Insulated
Volts
Alternating Current
Amps
Watts
Underwriters Laboratories, Inc.
US
C
United States and Canada
ASSEMBLY
WARNING T o reduce the risk of injury ,
always unplug tool before attaching or removing accessories or making adjustments. Use
only specifi cally recommended accessories.
Others may be hazardous.
WARNING T o reduce the risk of injury ,
do not remove or attach accessory tips until
tool has cooled to room temperature.
--
--
--
Installing/Removing Nozzles
1. To install, slide the nozzle onto the heat gun
nose.
2. Adjust heat, airfl ow, distance and length of ap-
plication as necessary.
3. To remove, allow tool to cool to room temperature, then pull nozzle away from tool.
WARNING T o reduce the risk of injury ,
always unplug tool before attaching or removing accessories or making adjustments. Use
only specifi cally recommended accessories.
Others may be hazardous.
WARNING T o reduce the risk of injury ,
wear safety goggles or glasses with side
shields.
Selecting Temperature
The proper amount of heat for each application
depends on the temperature selected, distance
between the nozzle and workpiece, and the length
of time heat is applied. Experiment with scrap materials and start with the lowest temperature. Be
cautious when working until the proper combination
of heat, distance and time of application has been
obtained. Use a back and forth motion when applying heat unless concentrated heat is desirable.
When done, allow the nozzle to cool by placing the
tool upright on a fl at surface using the support stand
areas. Place the cord so the heat gun won’t tip.
The electronic temperature control system
regulates the temperature within the tool's heating element. Unlike non-electronic heat guns,
MILWAUKEE's electronic heat gun will maintain
the temperature.
1. For Low Airfl ow/Low Tem-
perature, push the switch to
the (I) position.
2. For Medium Airflow/Vari-
able Temperature, push
the switch to the (II) position. Use the temperature
/ buttons to increase or
decrease the temperature
(100°F - 1100°F) by 10°F increments.
3. For High Airfl ow/Variable Temperature, push the
switch to the (III) position. Use the temperature
/ buttons to increase or decrease the tem-
perature (100°F - 1100°F) by 10°F increments.
When the tool is switched OFF, the last selected
temperature is retained.
Hands-Free Use
The heat guns can be positioned upright on a stable
surface, leaving both hands free for the application.
Always place the tool upright on a fl at surface using
the support stand areas. Place the cord so the heat
gun won’t tip. The rear vent openings are designed
to allow air fl ow even when the tool is resting on
the end cap. Do not cover the vents with foreign
materials such as clothing or rags.
Types of Nozzles
• Hook Nozzle - Surrounding heat for thin pipe weld-
ing, soft soldering copper pipes, tube shaping and
shrinking of shrink tubes.
• Air Reduction Nozzle - Intensifi ed, spot directed
heat for corners, plexiglas bending and soldering.
5
OPERATION
I
II
III
• Defl ector Nozzle - Defl ected heat protects glass
window panes when removing paint and putty.
• Air Spreader Nozzle - Directs heat over large
areas for drying, removing paint, fl oor coverings,
and vinyl tops.
APPLICATIONS
WARNING To reduce the risk of heat
damage and personal injury, shield combustible materials and areas adjacent to
workpiece. Protect yourself from hot paint
scrapings and dust.
Removing Paint
Read safety instructions for removing paint before
proceeding with paint removal.
1. Begin work with low temperature setting.
2. Place nozzle approximately 1" away from work
surface.
3. Pass nozzle back and forth over a small area of
workpiece.
4. Gradually increase heat until paint starts to
blister, then remove heat.
5. Remove paint using a sharp-edged putty knife.
Creating Bends
Both variable temperature and dual temperature
heat guns are ideal for creating bends in plexiglas
that is used for guards and fi xtures.
1. T o form a bend, use either a low or high tempera-
ture setting. When using a low temperature, hold
the heat gun close to the workpiece and pass the
nozzle back and forth slowly. When using a high
temperature, hold the heat gun further away
from the workpiece and pass the nozzle back
and forth rapidly.
2. Pass the nozzle over entire length of the surface
to be bent. Applying heat to only part of the
surface will make bending uneven.
Soldering
1. Attach the air reduction or hook nozzle to the
heat gun.
2. De-burr the pipe and joint using sandpaper or
steel wool.
3. T o solder with either lead or non-lead solder, coat
the tip on both the copper pipe and the joint with
fl ux. Then slip the joint over the pipe.
4. Slip the accessory nozzle around the joint. With
the heat gun at a high temperature setting, apply
heat to the joint.
5. When the fl ux bubbles, add solder and position
heat gun so excess solder does not drip into the
heat gun.
Heat Shrinking
1. Attach the air reduction or hook nozzle to the
heat gun.
2. To heat shrink tubing, use a low temperature
setting. Apply heat to the workpiece using a side
to side motion until tubing has shrunk. Remove
heat immediately.
MAINTENANCE
WARNING To reduce the risk of
injury, always unplug your tool before
performing any maintenance. Never disassemble the tool or try to do any rewiring
on the tool’s electrical system. Contact a
MILWAUKEE service facility for ALL repairs.
Maintaining Tools
Keep your tool in good repair by adopting a regular
maintenance program. Before use, examine the
general condition of your tool. Inspect guards,
switches, tool cord set and extension cord for
damage. Check for loose screws, misalignment,
binding of moving parts, improper mounting, broken parts and any other condition that may affect
its safe operation. If abnormal noise or vibration
occurs, turn the tool off immediately and have the
problem corrected before further use. Do not use a
damaged tool. T ag damaged tools “DO NOT USE”
until repaired (see “Repairs”).
WARNING T o reduce the risk of injury ,
electric shock and damage to the tool, never
immerse your tool in liquid or allow a liquid
to fl ow inside the tool.
Cleaning
Clean dust and debris from vents. Keep the tool
handles clean, dry and free of oil or grease. Use
only mild soap and a damp cloth to clean your tool
since certain cleaning agents and solvents are
harmful to plastics and other insulated parts. Some
of these include: gasoline, turpentine, lacquer thinner, paint thinner, chlorinated cleaning solvents,
ammonia and household detergents containing
ammonia. Never use fl ammable or combustible
solvents around tools.
Repairs
If your tool is damaged, return the entire tool to the
nearest service center.
ACCESSORIES
WARNING T o reduce the risk of injury ,
always unplug the tool before attaching or
removing accessories. Use only specifi cally
recommended accessories. Others may be
hazardous.
For a complete listing of accessories refer to your
MILWAUKEE Electric Tool catalog or go on-line
to www.milwaukeetool.com. To obtain a catalog,
contact your local distributor or a service center.
LIMITED WARRANTY - USA AND CANADA
Every MILWAUKEE power tool (including cordless product – tool, battery pack(s) - see separate & distinct
CORDLESS BATTERY PACK LIMITED WARRANTY statements & battery charger and Work Lights*) is warranted to the original purchaser only to be free from defects in material and workmanship. Subject to certain
exceptions, MILWAUKEE will repair or replace any part on an electric power tool which, after examination, is
determined by MILWAUKEE to be defective in material or workmanship for a period of fi ve (5) years* after the
date of purchase unless otherwise noted. Return of the power tool to a MILWAUKEE factory Service Center
location or MILWAUKEE Authorized Service Station, freight prepaid and insured, is required. A copy of the
proof of purchase should be included with the return product. This warranty does not apply to damage that
MILWAUKEE determines to be from repairs made or attempted by anyone other than MILWAUKEE authorized
personnel, misuse, alterations, abuse, normal wear and tear, lack of maintenance, or accidents.
*The warranty period for, Job Site Radios, M12™ Power Port, M18™ Power Source, and T rade T itan™ Industrial Work Carts is one (1) year from the date of purchase. The warranty period for a LED Work Light and LED
Upgrade Bulb is a limited LIFETIME warranty to the original purchaser only, if during normal use the LED bulb
fails the Work Light or Upgrade Bulb will be replaced free of charge.
*This warranty does not cover Air Nailers & Stapler, Airless Paint Sprayer, Cordless Battery Packs, Gasoline
Driven Portable Power Generators, Hand Tools, Hoist – Electric, Lever & Hand Chain, M12™ Heated Jackets,
Reconditioned product and Test & Measurement products. There are separate and distinct warranties available for these products.
Warranty Registration is not necessary to obtain the applicable warranty on a MILWAUKEE power tool product.
The manufacturing date of the product will be used to determine the warranty period if no proof of purchase is
provided at the time warranty service is requested.
ACCEPTANCE OF THE EXCLUSIVE REPAIR AND REPLACEMENT REMEDIES DESCRIBED HEREIN IS A
CONDITION OF THE CONTRACT FOR THE PURCHASE OF EVERY MILWAUKEE PRODUCT . IF YOU DO NOT
AGREE TO THIS CONDITION, YOU SHOULD NOT PURCHASE THE PRODUCT. IN NO EVENT SHALL MIL-
WAUKEE BE LIABLE FOR ANY INCIDENTAL, SPECIAL, CONSEQUENTIAL OR PUNITIVE DAMAGES, OR FOR
ANY COSTS, ATTORNEY FEES, EXPENSES, LOSSES OR DELA YS ALLEGED T O BE AS A CONSEQUENCE
OF ANY DAMAGE TO, FAILURE OF, OR DEFECT IN ANY PRODUCT INCLUDING, BUT NOT LIMITED TO, ANY
CLAIMS FOR LOSS OF PROFITS. SOME STA TES DO NOT ALLOW THE EXCLUSION OR LIMIT A TION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMIT A TION OR EXCLUSION MA Y NOT APPL Y
TO YOU. THIS W ARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS WARRANTIES, WRITTEN
OR ORAL. TO THE EXTENT PERMITTED BY LAW, MILWAUKEE DISCLAIMS ANY IMPLIED WARRANTIES,
INCLUDING WITHOUT LIMIT A TION ANY IMPLIED W ARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PAR TICULAR USE OR PURPOSE; TO THE EXTENT SUCH DISCLAIMER IS NOT PERMITTED BY LAW , SUCH
IMPLIED WARRANTIES ARE LIMITED TO THE DURATION OF THE APPLICABLE EXPRESS WARRANTY AS
DESCRIBED ABOVE. SOME ST A TES DO NOT ALLOW LIMITA TIONS ON HOW LONG AN IMPLIED WARRANTY
LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU, THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
This warranty applies to product sold in the U.S.A. and Canada only.
Please consult the ‘Service Center Search’ in the Parts & Service section of MILWAUKEE’s website www.mil-
waukeetool.com or call 1.800.SAWDUST (1.800.729.3878) to locate your nearest service facility for warranty
and non-warranty service on a Milwaukee electric power tool.
LIMITED WARRANTY - MEXICO, CENTRAL AMERICA AND CARIBBEAN
TECHTRONIC INDUSTRIES' warranty is for 5 year since the original purchase date.
This warranty card covers any defect in material and workmanship on this Power Tool.
To make this warranty valid, present this warranty card, sealed/stamped by the distributor or store where you purchased the product, to the Authorized Service Center (ASC). Or , if this card has not been sealed/stamped, present the
original proof of purchase to the ASC.
Call toll-free 1 800 832 1949 to fi nd the nearest ASC, for service, parts, accessories or components.
Procedure to make this warranty valid
Take the product to the ASC, along with the warranty card sealed/stamped by the distributor or store where you purchased the product, and there any faulty piece or component will be replaced without cost for you. We will cover all
freight costs relative with this warranty process.
Exceptions
This warranty is not valid in the following situations:
a) When the product is used in a different manners from the end-user guide or instruction manual.
b) When the conditions of use are not normal.
c) When the product was modifi ed or repaired by people not authorized by TECHTRONIC INDUSTRIES.
Note: If cord set is damaged, it should be replaced by an Authorized Service Center to avoid electric risks.
SERVICE AND ATTENTION CENTER
Model:
Av Presidente Mazarik 29 Piso 7, 11570 Chapultepec Morales
Miguel Hidalgo, Distrito Federal, Mexico
Date of Purchase:
Ph. 52 55 4160-3547
Distributor or Store Stamp:
IMPORTED AND COMMERCIALIZED BY:
TECHTRONIC INDUSTRIES MEXICO, .S.A. DE C.V.
Av Presidente Mazarik 29 Piso 7, 11570 Chapultepec Morales
Miguel Hidalgo, Distrito Federal, Mexico
6
7
Loading...