Milwaukee 7200-20 Operator's Manual
Cat. No. / No de cat.
7200-20
ROUND HEAD FRAMING NAILER
CLOUEUSE À BANDE POUR CHARPENTE
CLAVADORA DE CABEZA REDONDA
OPERATOR'S MANUAL
MANUEL de L'UTILISATEUR
MANUAL del OPERADOR
WARNING To reduce the risk of injury, user must read and understand operator's manual.
AVERTISSEMENT An de réduire le risque de blessures, l'utilisateur doit lire et bien
comprendre le manuel.
ADVERTENCIA Para reducir el riesgo de lesiones, el usuario debe leer y entender el manual.
2
GENERAL SAFETY INSTRUCTIONS
DANGER
Important safety instructions. Save
these instructions pertaining to a
risk of injury or death.
WARNING
When using tools, basic precautions
should always be followed, including
the following:
GENERAL
•To reduce the risk of injury, read all instructions
before using the tool.
WORK AREA
•Keep the work area clean and well lighted. Cluttered
benches and dark areas increase the risk of injury.
•Do not operate the tool in explosive atmospheres,
such as in the presence of ammable liquids,
gases, or dust. The tool is able to create sparks
resulting in the ignition of the dust or fumes.
•Keep bystanders, children, and visitors away while
operating the tool. Distractions are able to result in
the loss of control of the tool.
•Know what is behind your workpiece. A fastener
could travel through the workpiece and out the other
side, striking a bystander and causing serious injury.
•
DANGER
Avoid performing operations where
the fastener may contact hidden
wiring. Contact with a “live” wire will make exposed
metal parts of the tool “live” and shock the operator,
resulting in serious injury or death. Contact a qualied
electrician to ensure a safe work environment exists.
PERSONAL SAFETY
•Stay alert. Watch what you are doing and use common
sense when operating the tool. Do not use the tool
while tired or under the inuence of drugs, alcohol, or
medication. A moment of inattention while operating
the tool increases the risk of injury to persons.
•Dress properly. Do not wear loose clothing or jewelry.
Contain long hair. Keep hair, clothing, and gloves away
from moving parts. Loose clothes, jewelry, or long hair
increases the risk of injury to persons as a result of
being caught in moving parts.
•Avoid unintentional starting. Remove nger from
the trigger when not driving fasteners. Be sure the
trigger is not pulled before connecting to the air supply.
Do not carry the tool with your nger on the trigger or
connect the tool to the air supply with the trigger pulled.
•Do not overreach. Keep proper footing and balance
at all times. Proper footing and balance enables better
control of the tool in unexpected situations.
•Use safety equipment. A dust mask, non-skid safety
shoes and a hard hat used for appropriate conditions
will reduce personal injuries.
•The operator and other people in the work area
must wear eye protection in accordance with ANSI
Z87.1. Eye protection does not t all operators in the
same way. Make sure the eye protection chosen has
side shields or provides protection from ying debris
both from the front and sides. The employer is responsible for enforcing the use of eye protection by the operator and other people in the work area. When required,
wear head protection in accordance with ANSI Z89.1.
•Always wear ear protectors when using the tool
for extended periods. Prolonged exposure to high
intensity noise is able to cause hearing loss.
•Do not carry an air hose or a tool connected to an air
hose when climbing ladders, rigging or scaffolding.
•Do not attach an air hose or tool connected to an
air hose to your body when working at elevated
heights. Attach the hose to the structure to reduce
the risk of loss of balance and injury if the hose shifts.
•Always assume that the tool contains fasteners.
Careless handling of the tool can result in unexpected
ring of fasteners and personal injury.
•Do not point the tool towards yourself or anyone
nearby. Unexpected triggering will discharge the
fastener causing an injury.
•Do not nail on top of another nail. This can cause
the nail to be deected and hit someone, or cause the
tool to react and result in a risk of injury to persons.
TOOL USE AND CARE
•Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding
the work by hand or against the body is unstable and
is able to lead to loss of control.
•Do not force the tool. Use the correct tool for the
application. The correct tool will do the job better and
safer at the rate for which the tool is designed.
•Do not use the tool if the trigger does not turn the
tool on or off. Any tool that cannot be controlled with
the trigger is dangerous and must be repaired.
•Disconnect the tool from the air source, then
empty the magazine before making adjustments,
doing tool maintenance, clearing jams, touching
the workpiece contact or tool is outside your supervision or control. Verify the tool is empty and there
is no residual pressure in the tool prior to performing
these actions. Such precautionary measures reduce
the risk of injury to persons.
•Disconnect the tool from the power source when
the fastener jams in the tool. While removing a
jammed fastener, the tool may be accidentally activated if it is plugged in.
•Use caution while removing a jammed fastener.
The mechanism may be under compression and the
fastener may be forcefully discharged while attempting
to free a jammed condition.
•Store idle tools out of reach of children and other
untrained persons. A tool is dangerous in the hands
of untrained users.
•Maintain the tool with care. A properly maintained
tool reduces the risk of injury. If the tool has been
dropped, received a sharp blow, been run over, etc.,
perform the "Required Daily Testing" before further use.
•Check for misalignment or binding of moving
parts, breakage of parts, and any other condition
that affects the tool’s operation. If damaged, have
the tool serviced before using. Many accidents are
caused by poorly maintained tools. There is an increased risk of the tool bursting if the tool is damaged.
•Use only those fasteners specifically recommended. Fasteners not identied for use with this
tool by the tool manufacturer are able to result in a
risk of injury to persons or tool damage when used in
this tool. See the "Specications" section for fastener
requirements.
•Do not use this tool for fastening electrical cables.
It is not designed for electric cable installation and
may damage the insulation of electric cables thereby
causing electric shock or re hazards.
•Use only accessories that are identied by the
manufacturer for the specic tool model. Use of an
accessory not intended for use with the specic tool
model, increases the risk of injury to persons.
•Do not attempt to modify tool or defeat safety
measures. Serious injury could occur.
SERVICE
•a) Tool service must be performed only by qualied
repair personnel.
3
b) The wrench provided is for tightening screws
during "Required Daily Testing".
c) Use only identical replacement parts recom-
mended by the manufacturer.
•Use only the air tool lubricants supplied with the
tool or specied by the manufacturer. Do not use
other lubricants; they will damage the tool. See "Accessories" for a list of recommended air tool lubricants.
AIR SOURCE
•
DANGER
Do not use oxygen, combustible
gases or bottled gases as a power
source for this tool. The tool will explode and cause
death or serious injury.
•Never connect to an air source that is capable of
exceeding 200 psi. Over pressurizing the tool may
result in bursting, abnormal operation, breakage of
the tool or serious injury to persons. Use only clean,
dry, regulated compressed air at the rated pressure
or within the rated pressure range as marked on the
tool. Prior to using the tool, always verify that the air
source has been adjusted to the rated air pressure or
within the rated air-pressure range. Air compressors
should comply with ANSI B19.3.
SPECIFIC SAFETY INSTRUCTIONS
FOR NAILERS
•Use air supply hoses with a minimum working
pressure rating of 200 psi.
•Use pressure regulators to limit the air pressure
supplied to the tool. Set the regulators to no more
than 120 psi.
•Install only hose couplings that will allow all pres-
sure to be removed from tool when disconnected
from the source. If the wrong tting is installed,
pressure may remain in the tool after disconnection,
allowing it to drive a fastener, possibly causing injury.
•Prior to each use, check workpiece contact and
trigger for correct operation. Do not disassemble or
clamp parts of the workpiece contact, trigger, or driving
mechanism. This will cause unexpected actuation,
resulting in serious injury.
•Never point the discharge area of the tool at any
body parts or at other people. Always assume the
tool is loaded and capable of driving a fastener.
•Do not actuate the tool unless the tool is placed
rmly against the workpiece. If the tool is not in con-
tact with the workpiece, the fastener may be deected
away from your target.
•Do not engage in horseplay. The discharged fasteners are projectiles capable of causing serious injury.
•When using the tool, ensure the workpiece contact
is securely placed on the workpiece. Hold the tool
rmly and be prepared for the recoil.
•Do not remove, tamper with, or otherwise cause
the tool operating controls to become inoperable.
This will cause unexpected actuation, resulting in
serious injury.
•Do not operate a tool if any portion of the tool
operating controls is inoperable, disconnected,
altered, or not working properly. This will cause
unexpected actuation, resulting in serious injury.
•Always keep hands and body away from discharge
area of the tool. Never attempt to clear a jammed
workpiece contact by grasping the discharge area of
the tool. Fasteners discharged from tool can cause
serious injury if they contact hands or body.
•Do not drive fasteners close to the edge of the
workpiece. Fasteners can slip off corners and edges
or penetrate through thin material, making them projectiles capable of causing serious injury.
•Use the tool only for the intended purpose. Do
not abuse the tool. Do not use as a hammer, stamp
or engrave information onto parts, drop or impact the
tool or otherwise apply excess force to the tool in
use. Do not mount the tool to stands or modify it for
stationary use.
•Do not carry tool by the air hose. Only carry the
tool by the handle with your nger off of the trigger.
•Do not use this tool without the safety warning
label in place. If the label is damaged or missing,
contact MILWAUKEE for a free replacement.
FUNCTIONAL DESCRIPTION
1
2
3
4
5
6
7
8
14
15
11
13
10
12
16
9
1. No-mar pad
2. Toe-nail claw (not shown)
3. Workpiece contact
4. Depth of drive adjustment
5. Exhaust deector
6. Actuation selector
7. Trigger
8. Rafter hook
9. 3/8" NPT quick connector
10. Nameplate (on top of magazine)
11. Nail stop tab
12. Extra no-mar pad storage (on back of magazine)
13. Warning label (on top of magazine)
14. Pusher
15. Pusher release button
16. Nail guide
SYMBOLOGY
Read operator's manual
Wear eye protection
Keep hands away
4
3. Storage for an additional pad is available on the
magazine of the tool.
4. To replace the pad, t it into place over the points of
the claw.
Exhaust
The exhaust cap can be adjusted to direct the exhaust
as desired. Turn the exhaust cap to the desired locking position.
Removing and Installing the Rafter Hook
Rafter hook
Front of tool
End cap
Screw (2)
3/8" NPT
quick
connector
To remove the hook:
1. Rotate the hook until it snaps into one of the preset
positions.
2. Remove the two mounting screws using the wrench
provided.
3. Pull the hook off the rear of the tool.
To install the hook:
1. Align the spring-loaded post on the hook with a slot
on the rear of the tool.
2. Slide the hook onto the tool, making sure the hook
points toward the front of the tool. Push the hook up
against the end cap.
3. Install the two mounting screws using the wrench
provided. Tighten securely.
4. Verify that the hook is installed correctly by rmly
pulling the hook toward the air inlet. It must not move.
Lubricating the Tool
Lubricate the tool with air tool lubricant before connecting the air supply. Under low use, lubricate once a day.
Under heavy use, lubricate twice a day. Use only a few
drops of oil at a time. Using too much oil will cause it to
collect in the tool and be noticeable in the exhaust. Do
not use detergent oil, WD-40, transmission uid, motor
oil, or other lubricants not specically designated as air
tool lubricant. These lubricants will cause accelerated
wear to the seals, o-rings and bumpers in the tool, resulting in poor tool performance and frequent maintenance.
2-3 drops of air
tool lubricant
3/8" NPT quick
connector
SPECIFICATIONS
Cat. No. ........................................................ 7200-20
Operating Pressure .................................min. 70 PSI
..............................................................max. 120 PSI
Fastener Length ............................................. min. 2"
..................................................................... max.3.5"
Collation Angle............................................... 20°-22°
Fastener Size (Diameter) .........................min. 0.113"
................................................................ max. 0.148"
Air Consumption .................. 0.16 ft3/cycle at 100 PSI
Air Inlet ........................................................3/8" NPT
Magazine Capacity ...................................64-72 nails
TERMINOLOGY
Actuate
To cause movement of the tool component(s) intended
to drive a fastener.
Actuation System
The use of a trigger, workpiece contact and/or other
operating control, separately or in some combination
or sequence, to actuate the tool.
• Single sequential actuation
An actuation system that requires the workpiece con-
tact and then the trigger to be activated in a specic
sequence to drive a fastener. Additional actuation can
occur when the trigger is released and reactivated.
• Contact actuation
An actuation system that requires the workpiece con-
tact and the trigger to be activated in any sequence
to drive a fastener. Additional actuation can occur
when either the workpiece contact or the trigger is
released and reactivated.
• Selective actuation
An actuation system that allows selection of actua-
tion systems: single sequential actuation or contact
actuation.
Fastener
A staple, pin, brad, nail, or other fastening device which
is designed and manufactured for use in the tools.
Jam
An obstruction in the feed or drive areas of the tool.
Workpiece Contact
An operating control element on the tool intended to be
activated by the workpiece to be fastened.
ASSEMBLY
WARNING
Disconnect the air supply from the
tool and remove fastener strips be-
fore changing or removing accessories. Only use
accessories specically recommended for this tool
by the manufacturer. Others may be hazardous.
The operator and other people in the work area
must wear eye protection in accordance with ANSI
Z87.1. Eye protection does not t all operators in
the same way. Make sure the eye protection chosen
has side shields or provides protection from ying
debris both from the front and sides.
No-Mar Pad
The No-Mar Pad on the nose of the tool protects the
workpiece when the workpiece contact is compressed
during actuation. The pad can be removed and replaced.
1. Before removing or replacing no-mar pads, disconnect the air supply from the tool and remove fastener
strips.
2. To remove the pad, pull the pad open and away from
the toe-nailing claw.
5
Connecting the Air Supply
DANGER
Do not use oxygen, combustible
gases or bottled gases as a power
source for this tool. The tool will explode and cause
death or serious injury.
WARNING
Always use a coupling that dis-
charges all the compressed air in the
tool at the time the tting or hose coupling is disconnected. Using a coupling that does not discharge the compressed air could cause unintended
operation and serious injury.
Use only clean, dry compressed air with a maximum
pressure of 200 psi. Before connecting the tool to the
air supply, check the air compressor regulator gauge to
be sure it is functioning properly, with a range between
70-120 psi. Air pressure higher than 120 psi could cause
injury and property damage. The correct pressure is the
lowest pressure that will do the job.
To connect the air supply:
1. Remove the plastic plug from the quick connector.
2. Lubricate the quick connector with 2-3 drops air tool
lubricant.
3. Snap the air hose onto the quick connector.
4. Check for air leakage.
NOTE: Use only a 3/8" NPT quick connector. To improve
the seal between the connector and the tool, and to help
protect against oxidation, apply a PTFE tape or paste
to the connector threads before insertion.
Installing Fastener Strips
WARNING
Always point the tool away from
yourself and others when installing
fasteners. Failure to do so could result in injury.
Always make sure the tool's magazine is EMPTY
before connecting to the air supply. The tool may
actuate when the tool is rst connected to the air
supply. Always connect the tool to the air supply
before loading nails to prevent injury from unintended actuation.
Never install fasteners with the workpiece contact
or trigger activated. Failure to do so could result
in injury.
Use only recommended fasteners of the correct
size, length, collation angle and head type, as
indicated on the tool's nameplate. Refer to the
"Accessories" section for information on recommended fasteners. Other fasteners could result in
tool malfunction, leading to injury.
1. Verify that the magazine is empty and then connect
the air supply to the tool.
2. Lay the tool on its side and point the nose of the tool
away from yourself and others.
3. Feed fastener strips into the magazine and over the
nail stop tab. Be sure the point of the fasteners is
pointed downward.
NOTE: Use only recommended fasteners of the
correct size, length, collation angle and head type
as indicated on the tool's nameplate.
4. Slide the pusher to the rear of the magazine and over
the nail stop tab.
5. Gently allow the pusher to slide forward, pushing the
fasteners toward the driving mechanism. The pusher
will stop when it rests against the end of the fastener
strip.
NOTE: The fasteners must be aligned with the nose
of the tool for the fasteners to be installed correctly.
Removing Fastener Strips
WARNING
To avoid serious injury, disconnect
the tool from the air supply before
removing fastener strips or clearing a jammed
fastener.
Keep ngers clear of fastener track of magazine.
Pusher could pinch ngers, causing injury.
1. Lay the tool on its side and point the nose of the tool
away from yourself and others.
2. Disconnect the air supply from the tool.
3. To remove fasteners, press the pusher release button
on the pusher and gently slide the pusher forward
toward the driving mechanism.
4. Slide the nails back until they stop.
5. Press down on the fastener stop tab near the end of
the magazine and slide the fasteners over the tab.
6. Remove fastener strip from the tool.
7. Reload according to "Installing Fastener Strips".
Clearing a Jammed Fastener
Most jams are caused by a fastener or part of a fastener
wedging between the driver blade and the nail guide.
Fastener strips with an incorrect collation angle or the
wrong fastener type (such as clipped head fasteners)
may cause continuous jamming. To clear the jam:
1. Lay the tool on its side and point the nose of the tool
away from yourself and others.
2. Disconnect the air supply from the tool and remove
fastener strip.
3. Insert a screwdriver into the end of the nail guide.
The tip of the screwdriver should contact the tip of
the driver blade.
4. Tap the screwdriver gently with a hammer. The
screwdriver will push the driver blade back, freeing
the jam.
5. Remove the fastener and other debris (use needlenose pliers if necessary).
6. Follow the steps under "Required Daily Testing"
before restarting the work.
Tap screwdriver
to free fastener
6
OPERATION
WARNING
The operator and other people in the
work area must wear eye protection
in accordance with ANSI Z87.1. Eye protection does
not t all operators in the same way. Make sure the
eye protection chosen has side shields or provides
protection from ying debris both from the front
and sides. The employer is responsible for enforcing the use of eye protection by the operator and
other people in the work area. When required, wear
head protection in accordance with ANSI Z89.1.
Selecting Actuation Mode
The selectable trigger can be set to either Single Sequential Actuation mode or Contact Actuation mode.
Single
Sequential
Actuation
Contact
Actuation
1.Push in and hold the Actuation Selector.
2. Rotate the Selector to Single Sequential Actuation
(T) or Contact Actuation (TTT).
3. Release the Actuation Selector.
NOTE: Be sure the selector is snapped into position.
Understand the actuation process before use.
WARNING
To reduce the risk of injury to your-
self and others, test the tool before
beginning work each day according to the "Required Daily Testing" section.
Do not use the tool unless you thoroughly understand the actuation operation selected.
Disconnect the air supply from the tool and remove
fastener strips before leaving the work area, moving the tool to another location, or handing the tool
to another person. Failure to do so could result in
serious injury.
Do not carry an air hose or a tool connected to an
air hose when climbing ladders, rigging or scaffolding. Do not attach an air hose or tool connected to
an air hose to your body when working at elevated
heights. Attach the hose to the structure to reduce
the risk of loss of balance and injury if the hose
shifts.
Do not use this tool for fastening electrical
cables. It is not designed for electric cable
installation and may damage the insulation of
electric cables thereby causing electric shock
or re hazards.
Single Sequential Actuation Operation
1. Grip the handle rmly.
2. Position the nose of the tool on the work surface.
3. Push the tool against the work surface, compressing
the workpiece contact.
4. Pull the trigger to drive the fastener. The tool will recoil
away from the workpiece as the fastener is driven.
5. Remove your nger from the trigger and remove the
tool from the workpiece.
NOTE: If the tool is not removed from the workpiece,
another fastener may be driven if the trigger is pulled
again.
Contact Actuation Operation
1. Grip the handle rmly.
2. Pull and hold the trigger.
3. Push the tool against the work surface, compressing
the workpiece contact to drive the fastener. The tool
will recoil away from the workpiece as the fastener
is driven.
NOTE: Contact Actuation will also work by rst com-
pressing the workpiece contact, then pulling the trigger.
Reload Indicator
To indicate that the magazine is almost empty of fasteners (about 4-5 left), the workpiece contact will not
compress, preventing operation under usual pressure.
Install more fasteners to continue working.
WARNING
NEVER wedge or hold back the
workpiece contact mechanism during operation of the tool. Never attempt to clear a
jammed workpiece contact by grasping the discharge area of the tool. Doing so could result in
serious injury.
To avoid serious injury, do not attempt to prevent
the recoil by holding the tool too rmly against the
work. Keep face and body away from the tool. Dur-
ing normal use, the tool will recoil immediately after
driving a fastener. This is a normal function of the
tool. Restriction to the recoil can result in a second
fastener being driven when the tool is in Contact
Actuation mode. Grip the handle rmly, let the tool
do the work, and do not place a second hand on
top of the tool or near exhaust.
Setting the Air Pressure and Depth of Drive
The amount of air pressure required will depend on the
size of the fastener and the workpiece material.
WARNING
Know what is behind your workpiece.
A fastener could travel through the
workpiece and out the other side, striking a bystander and causing serious injury. Lower the air
pressure and/or depth of drive to prevent the fas-
tener from being pushed all the way through the
workpiece.
1. Lay the tool on its side and point the nose of the tool
away from yourself and others.
2. Disconnect the air supply from the tool and remove
fastener strip.
3. Set the depth of drive adjustment to the middle of its
range.
4. Reload fastener strip according to "Installing Fastener
Strips".
Set to
middle of
range
7
5. Begin testing the depth of drive by driving a test fastener into the same type of workpiece material used
for the actual job using an air pressure of 90-95 psi.
6. Raise or lower the air pressure to nd the lowest
setting that will drive the fastener consistently. Do
not exceed 120 psi.
NOTE: It may be possible to achieve the desired
depth with air pressure adjustments alone. If ner
adjustments are needed, use the depth of drive
adjustment.
7. To ne-tune the depth of drive, disconnect the air
supply and lay the tool on its side and point the nose
of the tool away from yourself and others. Remove
fastener strip. Turn the depth selector left or right to
increase or decrease the driving depth.
8. Reload fastener strip according to "Installing Fastener
Strips".
9. Drive a test fastener and repeat step 7 and 8 until
desired depth is reached.
REQUIRED DAILY TESTING
WARNING
To reduce the risk of injury to your-
self and others, test the tool before
beginning work each day or if the tool is dropped,
received a sharp blow, been run over, etc. Complete
the following checklist IN ORDER. If the tool does
not work as it should, contact a MILWAUKEE service
facility immediately.
Always point tool away from yourself and others.
1. Disconnect the air supply from the tool and remove
fastener strip.
2. Check all screws, bolts, nuts, and pins on the tool.
Any loose fasteners must be tightened.
3. Pull back the fastener pusher on the magazine (to
override the Reload Indicator) and press the workpiece contact against a workpiece. It must move
smoothly.
4. With the workpiece contact pressed against the
workpiece, pull the trigger. It must move smoothly.
5. Connect the air supply (at 70 psi) to the tool. DO NOT
load a fastener strip.
6. Select the Single Sequential Actuation Operation. Air
must not leak from the tool.
Without pulling the trigger, pull back the fastener
pusher on the magazine (to override the Reload
Indicator) and press the workpiece contact against
a workpiece. The tool must not operate.
Holding the workpiece contact away from the work-
piece, pull back the fastener pusher on the magazine
(to override the Reload Indicator). Pull and hold the
trigger for 5 seconds. The tool must not operate.
Continue to pull and hold the trigger and push the
workpiece contact against a workpiece. The tool must
not operate.
Without pulling the trigger, pull back the fastener
pusher on the magazine (to override the Reload
Indicator) and press the workpiece contact against
a workpiece. Pull the trigger. The tool must operate.
Release the trigger. The driver must move up.
7. Select the Contact Actuation Operation.
Holding the workpiece contact away from the work-
piece, pull back the fastener pusher on the magazine
(to override the Reload Indicator) and pull the trigger.
The tool must not operate.
Continue to pull and hold the trigger and push the
workpiece contact against a workpiece. The tool must
operate.
8. If all previous tests work properly, set the tool for your
work. Select the operation and load fastener strips.
9. Set the depth of drive according to the "Setting the
Air Pressure and Depth of Drive" section.
10. If all tests operate properly, the tool is ready for use.
Repeat these tests before use each day or if the
tool is dropped, received a sharp blow, been run
over, jammed, etc.
MAINTENANCE
WARNING
To reduce the risk of injury, use only
identical replacement parts recom-
mended by the manufacturer. Tool service must be
performed only by qualied repair personnel. Al-
ways wear safety goggles or glasses with side
shields when servicing tools. Disconnect tool from
air supply before servicing.
Cleaning
Clean dust and debris from tool vents. Keep tool handles
clean, dry and free of oil or grease. Use only mild soap
and a damp cloth to clean the tool, since certain cleaning agents and solvents are harmful to plastics and
other parts. Some of these include gasoline, turpentine,
lacquer thinner, paint thinner, chlorinated cleaning solvents, ammonia and household detergents containing
ammonia. Never use ammable or combustible solvents
around tools.
Lubrication
Frequent, but not excessive, lubrication is required
for best performance. Oil added through the air line
connection will lubricate the internal parts. Do not use
detergent oil, WD-40, transmission uid, motor oil, or
other lubricants not specically designated as air tool
lubricant. These lubricants will cause accelerated wear
to the seals, o-rings and bumpers in the tool, resulting
in poor tool performance and frequent maintenance.
Cold Weather Operation
For cold weather operation, near and below freezing,
the moisture in the air line may freeze and prevent
tool operation. Use an air tool lubricant or permanent
antifreeze as a cold weather lubricant in the air line.
Do not store tools in a below-freezing environment. Ice
or frost could form on the tools' operating valves and
mechanisms, causing tool failure.
Air Supply-Pressure and Volume
Air volume is as important as air pressure. The air volume supplied to the tool may be inadequate because
of undersized ttings and hoses, or from the effects
of dirt and water in the system. Restricted air ow will
prevent the tool from receiving an adequate volume
of air, even though the pressure reading is high. The
results will be slow operation or reduced driving power.
Before evaluating tool problems for these symptoms,
trace the air supply from the tool to the supply source
for restrictive connectors, low points containing water
and anything else that would prevent full volume ow
of air to the tool.
ACCESSORIES
WARNING
Use only recommended accesso-
ries. Others may be hazardous.
For a complete listing of accessories, go online to
www.milwaukeetool.com or contact a distributor.
8
SERVICE - UNITED STATES
1-800-SAWDUST (1.800.729.3878)
Monday-Friday, 7:00 AM - 6:30 PM CST
or visit www.milwaukeetool.com
Contact Corporate After Sales Service Technical
Support with technical, service/repair, or warranty
questions.
Email: metproductsupport@milwaukeetool.com
Become a Heavy Duty Club Member at
www.milwaukeetool.com to receive important
notications regarding your tool purchases.
SERVICE - CANADA
Milwaukee Tool (Canada) Ltd
1.800.268.4015
Monday-Friday, 7:00 AM - 4:30 PM CST
or visit www.milwaukeetool.ca
LIMITED WARRANTY USA &
CANADA
Every MILWAUKEE air nailer - stapler is warranted to the original
purchaser only to be free from defects in material and workmanship.
Subject to certain exceptions, MILWAUKEE will repair or replace any
part on an air nailer - stapler which, after examination, is determined by
MILWAUKEE to be defective in material or workmanship for a period of
ve (5) years after the date of purchase. Return the air nailer - stapler
to a MILWAUKEE factory Service Center location or MILWAUKEE
Authorized Service Station, freight prepaid and insured is required.
A copy of the proof of purchase should be included with the return
product. This warranty does not apply to damage that MILWAUKEE
determines to be from repairs made or attempted by anyone other
than MILWAUKEE authorized personnel, misuse, alterations, abuse,
normal wear and tear, lack of maintenance, or accidents.
Normal Wear: air nailers – staplers, like all power tools, these products need periodic parts replacement and service to achieve best
performance. This warranty does not cover repair when normal use
has exhausted the life of a part including, but not limited to o-rings,
seals, bumpers and driver blades.
Warranty Registration is not necessary to obtain the applicable warranty on a MILWAUKEE product. The manufacturing date of the product
will be used to determine the warranty period if no proof of purchase
is provided at the time warranty service is requested.
ACCEPTANCE OF THE EXCLUSIVE REPAIR AND REPLACEMENT
REMEDIES DESCRIBED HEREIN IS A CONDITION OF THE CONTRACT FOR THE PURCHASE OF EVERY MILWAUKEE PRODUCT.
IF YOU DO NOT AGREE TO THIS CONDITION, YOU SHOULD NOT
PURCHASE THE PRODUCT. IN NO EVENT SHALL MILWAUKEE BE
LIABLE FOR ANY INCIDENTAL, SPECIAL, CONSEQUENTIAL OR
PUNITIVE DAMAGES, OR FOR ANY COSTS, ATTORNEY FEES,
EXPENSES, LOSSES OR DELAYS ALLEGED TO BE AS A CONSEQUENCE OF ANY DAMAGE TO, FAILURE OF, OR DEFECT IN
ANY PRODUCT INCLUDING, BUT NOT LIMITED TO, ANY CLAIMS
FOR LOSS OF PROFITS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT
APPLY TO YOU. THIS WARRANTY IS EXCLUSIVE AND IN LIEU
OF ALL OTHER EXPRESS WARRANTIES, WRITTEN OR ORAL.
TO THE EXTENT PERMITTED BY LAW, MILWAUKEE DISCLAIMS
ANY IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION
ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR USE OR PURPOSE; TO THE EXTENT SUCH
DISCLAIMER IS NOT PERMITTED BY LAW, SUCH IMPLIED WARRANTIES ARE LIMITED TO THE DURATION OF THE APPLICABLE
EXPRESS WARRANTY AS DESCRIBED ABOVE. SOME STATES
DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO
YOU, THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS,
AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
This warranty applies to product sold in the U.S.A. and Canada only.
Please consult the ‘Service Center Search’ in the Parts & Service
section of MILWAUKEE’s website www.milwaukeetool.com or call
1.800.SAWDUST (1.800.729.3878) to locate your nearest service
facility for warranty and non-warranty service on air nailers - staplers.
LIMITED WARRANTY - MEXICO,
CENTRAL AMERICA & CARIBBEAN
TECHTRONIC INDUSTRIES' warranty is for 5 year since the original
purchase date.
This warranty card covers any defect in material and workmanship
on this Power Tool.
To make this warranty valid, present this warranty card, sealed/
stamped by the distributor or store where you purchased the product,
to the Authorized Service Center (ASC). Or, if this card has not been
sealed/stamped, present the original proof of purchase to the ASC.
Call toll-free 1 800 832 1949 to nd the nearest ASC, for service, parts,
accessories or components.
Procedure to make this warranty valid
Take the product to the ASC, along with the warranty card sealed/
stamped by the distributor or store where you purchased the product,
and there any faulty piece or component will be replaced without
cost for you. We will cover all freight costs relative with this warranty
process.
Exceptions
This warranty is not valid in the following situations:
a) When the product is used in a different manners from the end-user
guide or instruction manual.
b) When the conditions of use are not normal.
c) When the product was modied or repaired by people not authorized
by TECHTRONIC INDUSTRIES.
Note: If cord set is damaged, it should be replaced by an Authorized
Service Center to avoid electric risks.
SERVICE AND ATTENTION CENTER:
Av Presidente Mazarik 29 Piso 7, 11570 Chapultepec Morales
Miguel Hidalgo, Distrito Federal, Mexico
Ph. 52 55 4160-3547
IMPORTED AND COMMERCIALIZED BY:
TECHTRONIC INDUSTRIES MEXICO, .S.A. DE C.V.
Av Presidente Mazarik 29 Piso 7, 11570 Chapultepec Morales
Miguel Hidalgo, Distrito Federal, Mexico
Model:
Date of Purchase:
Distributor or Store Stamp:
Loading...