Milwaukee Tool 6580-20 User Manual [en, es, fr]

OPERATOR'S MANUAL MANUEL de L'UTILISATEUR MANUAL del OPERADOR

Cat. No.

No de Cat.

6580-20 6740-20 6742-20 6780-20

6790-20 6791-20 6791-21

6792-20

HEAVY-DUTY SCREWDRIVER EXTRA ROBUSTE TOURNEVIS DESTORNILLADORES HEAVY-DUTY

TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND OPERATOR'S MANUAL.

AFIN DE RÉDUIRE LE RISQUE DE BLESSURES, L'UTILISATEUR DOIT LIRE ET BIEN COMPRENDRE LE MANUEL DE L'UTILISATEUR.

PARA REDUCIR EL RIESGO DE LESIONES, EL USUARIO DEBE LEER Y ENTENDER EL MANUAL DEL OPERADOR.

GENERAL POWER TOOL SAFETY WARNINGS

WARNING READ ALL SAFETY WARNINGS AND ALL INSTRUCTIONS. Failure

to follow the warnings and instructions may result in electric shock, ﬁ re and/or serious injury. Save all warnings and instructions for future reference. The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

• Keep work area clean and well lit. Cluttered or

WORK AREA SAFETY

dark areas invite accidents.

• Do not operate power tools in explosive atmospheres, such as in the presence of ﬂ ammable liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

• Keep children and bystanders away while operating a power tool. Distractions can cause

you to lose control.

ELECTRICAL SAFETY

• Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodiﬁ ed plugs and matching outlets will

reduce risk of electric shock.

• Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

• Do not expose power tools to rain or wet conditions. Water entering a power tool will increase

the risk of electric shock.

• Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords

increase the risk of electric shock.

• When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use

of a cord suitable for outdoor use reduces the risk of electric shock.

• If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces

the risk of electric shock.

PERSONAL SAFETY

• Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the inﬂ uence of drugs, alcohol or medication. A

moment of inattention while operating power tools may result in serious personal injury.

• Use personal protective equipment. Always wear eye protection. Protective equipment such

as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.

• Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with

your ﬁ nger on the switch or energising power tools that have the switch on invites accidents.

• Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may result in personal injury.

• Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

• Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewel- lery or long hair can be caught in moving parts.

• If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of

dust collection can reduce dust-related hazards.

POWER TOOL USE AND CARE

• Do not force the power tool. Use the correct power tool for your application. The correct

power tool will do the job better and safer at the rate for which it was designed.

• Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must be repaired.

• Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such pre-

ventive safety measures reduce the risk of starting the power tool accidentally.

• Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the

hands of untrained users.

• Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

• Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

• Use the power tool, accessories and tool bits etc., in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool

for operations different from those intended could result in a hazardous situation.

SERVICE

• Have your power tool serviced by a qualiﬁ ed repair person using only identical replacement parts. This will ensure that the safety of the power

tool is maintained.

SPECIFIC SAFETY RULES

• Hold power tool by insulated gripping sur-

faces, when performing an operation where the fastener may contact hidden wiring or its own cord. Fasteners contacting a “live” wire may

make exposed metal parts of the power tool “live” and could give the operator an electric shock.

• Maintain labels and nameplates. These carry important information. If unreadable or missing, contact a MILWAUKEE service facility for a free replacement.

• WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paint

• crystalline silica from bricks and cement and

other masonry products, and

• arsenic and chromium from chemically-treated

lumber. Your risk from these exposures varies, depending

on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to ﬁ lter out microscopic particles.

SYMBOLOGY

Double Insulated

Amperes

Volts

Alternating Current No Load Revolutions

per Minute (RPM)

Underwriters Laboratories, Inc. United States and Canada

Mexican Approvals Marking

SPECIFICATIONS

Cat. No. Volts AC Amps No Load RPM 6580-20

6740-20 6742-20 6780-20 6790-20 6791-20 6791-21 6792-20

120 120 120 120 120 120 120 120

6.5

0 - 1200 0 - 2500 0 - 4000 0 - 2700 0 - 2500 0 - 2500 0 - 2500 0 - 2500

FUNCTIONAL DESCRIPTION

1. Locator

2. Ramp-off sleeve

3. Nameplate 1

4. Belt clip

5. Bit clip

6. Lock button

7. Trigger

8. Forward/Reverse switch

9. Gear case

EXTENSION CORDS

Grounded tools require a three wire extension cord. Double insulated tools can use either a two or three wire extension cord. As the distance from the supply outlet increases, you must use a heavier gauge extension cord. Using extension cords with inadequately sized wire causes a serious drop in voltage, resulting in loss of power and possible tool damage. Refer to the table shown to determine the required minimum wire size. The smaller the gauge number of the wire, the greater the capacity of the cord. For example, a 14 gauge cord can carry a higher current than a 16 gauge cord. When using more than one extension cord to make up the total length, be sure each cord contains at least the minimum wire size required. If you are using one extension cord for more than one tool, add the nameplate amperes and use the sum to determine the required minimum wire size.

Guidelines for Using Extension Cords

• If you are using an extension cord outdoors, be sure it is marked with the sufﬁ x “W-A” (“W” in Cana- da) to indicate that it is acceptable for outdoor use.

• Be sure your extension cord is properly wired and in good electrical condition. Always replace a damaged extension cord or have it repaired by a qualiﬁ ed person before using it.

• Protect your extension cords from sharp objects, excessive heat and damp or wet areas.

Recommended Minimum Wire Gauge

For Extension Cords*

Nameplate

Amperes

0 - 2.0

2.1 - 3.4

3.5 - 5.0

5.1 - 7.0

7.1 - 12.0

12.1 - 16.0

16.1 - 20.0

* Based on limiting the line voltage drop to ﬁ ve volts at 150% of the rated amperes.

Extension Cord Length

25' 50' 75' 100' 150'

18 18 18 18 16 14 12

18 18 16 14 12 10

18 16 14 12 10

READ AND SAVE ALL

INSTRUCTIONS FOR FUTURE USE.

16 14 12 12

GROUNDING

ASSEMBLY

WARNING Improperly connecting the

grounding wire can result in the risk of electric shock. Check with a qualiﬁ ed electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the tool. Never remove the grounding prong from the plug. Do not use the tool if the cord or plug is damaged. If damaged, have it repaired by a MILWAUKEE service facility before use. If the plug will not ﬁ t the outlet, have a proper outlet installed by a qualiﬁ ed electrician.

Grounded Tools: Tools with Three Prong Plugs

Tools marked “Grounding Required” have a three wire cord and three prong grounding plug. The plug must be connected to a properly grounded outlet (See Figure A). If the tool should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user, reducing the risk of electric shock. The grounding prong in the plug is connected through the green wire inside the cord to the grounding system in the tool. The green wire in the cord must be the only wire connected to the tool's grounding system and must never be attached to an electrically “live” terminal. Your tool must be plugged into an appropriate outlet, properly installed and grounded in accordance with all codes and ordinances. The plug and outlet should look like those in Figure A.

Double Insulated Tools: Tools with Two Prong Plugs

Tools marked “Double Insulated” do not require grounding. They have a special double insulation system which satisﬁ es OSHA requirements and complies with the applicable standards of Underwriters Laboratories, Inc., the Canadian Standard Association and the National Electrical Code. Double Insulated tools may be used in either of the 120 volt outlets shown in Figures B and C.

Fig. A

Fig. B

Fig. C

WARNING T o reduce the risk of injury ,

always unplug tool before changing or removing accessories. Only use accessories speciﬁ cally recommended for this tool. Others may be hazardous.

Removing and Replacing Quik-Lok® Cords

(Cat. No. 6580-20, 6791-20) MILWAUKEE's exclusive Quik-Lok® Cords provide instant ﬁ eld replacement or substitution.

Fig. 1

1. To remove the Quik-Lok® Cord, turn the cord nut 1/4 turn to the left and pull it out.

2. T o replace the Quik-Lok® Cord, align the connector keyways and push the connector in as far as it will go. Turn the cord nut 1/4 turn to the right to lock.

Installing and Removing Bits TEKS Ramp-Off Locator Assembly

The locator assembly must be removed when changing bit sizes.

Fig. 2

Ramp-off

sleeve

1. Unplug tool. To remove the locator assembly, turn the ramp-off sleeve while pulling it away from the tool.

2. Pull out the magnetic socket and replace it with a new socket.

3. Push the locator assembly onto the nose of the tool until it snaps into place.

Magnetic socket

Locator

Installing and Removing Bits Drywall Ramp-Off Locator Assembly

Fig. 3

Ramp-off sleeve

Locator

1. Unplug tool. T o remove the locator assembly , turn the ramp-off sleeve while pulling it away from the tool.

2. Push insert bit into bit holder until it snaps into place. Push the bit holder into the nose of the tool until it snaps into place.

3. Push the locator assembly onto the nose of the tool until it snaps into place.

Installing and Removing Magnetic Sockets on Adjustable Screwdrivers For Cat. No. 6580-20

Fig. 4

1. Unplug tool.

2. T o remove the magnetic socket, slide the locking sleeve forward and pull out the socket.

3. To install the magnetic socket, slide the locking sleeve forward and push in the socket until it is fully seated.

For Cat. No. 6780-20

1. Unplug tool.

2. T o remove the magnetic socket, slide the locking sleeve forward and pull out the socket.

Fig. 5

3. To install the magnetic socket, simply push in the socket until it snaps into place.

Bit holder

Insert bit

Socket

Locking sleeve

Socket

Locking sleeve

OPERATION

WARNING T o reduce the risk of injury ,

always unplug tool before attaching or removing accessories or making adjustments. Use only speciﬁ cally recommended accessories. Others may be hazardous.

WARNING T o reduce the risk of injury ,

wear safety goggles or glasses with side shields.

Using Forward/Reverse Switch

Fig. 6

Switch

1. For forward (clockwise) rotation, push the forward/reverse switch to the left position as shown.

2. For reverse (counterclockwise) rotation, push the forward/reverse switch to the right position as shown.

Although an interlock prevents reversing the tool

while the motor is running, allow it to come to a full stop before reversing.

Forward

Reverse

Trigger

WARNING T o reduce the risk of injury ,

keep hands and cord away from the bit and all moving parts.

Starting, Stopping and Controlling Speed

1. To start the tool, pull the trigger.

2. To stop the tool, release the trigger.

3. To vary the drilling speed, simply increase or decrease pressure on the trigger. The further the trigger is pulled, the greater the speed.

Locking Trigger

The lock button holds the trigger in the ON position for continuous full speed use.

1. To lock the trigger, hold the lock button in while pulling the trigger. Release the trigger.

2. To unlock the trigger, pull the trigger and release. The lock button will pop out.

Adjusting Locator Assembly

The locator assembly controls the tool's driving depth. These screwdrivers feature a locator assembly with one-handed depth adjustment. Depth adjustments can be made easily and quickly by turning the locator with one hand. Detents inside the sleeve “lock” the selected depth. For the drywall ramp-off locator assembly, start with about 1/16" clearance between the head of the screw and nose with the snap-action clutch disengaged as shown.

For both locator assemblies, the detents on the inside of the sleeve represent different depths. Every two clicks of the locator equal 1/64". Continue adjusting the locator to the desired depth.

1. To increase the driving depth, simply rotate the locator in the direction labeled

2. To decrease the driving depth, simply rotate the locator in the direction labeled .

The detents “lock” the locator in place, ensuring

an accurate depth setting.

3. To remove the locator assembly, turn the rampoff sleeve while pulling it away from the tool. Reattaching the locator assembly will not change the depth setting.

Adjusting Torque Setting

These screwdrivers have a torque setting adjustment collar for driving different types of screws into different materials. When properly adjusted, the clutch will slip at a preset torque to prevent driving the screw too deep and to prevent damage to the screw or tool.

For Cat. Nos. 6580-20

The 6580-20 Screwdriver has a torque setting adjustment collar that may be adjusted to one of forty-four settings. The torque is adjustable from 10 to 140 inch-pounds. T o select a setting, turn the adjustment collar in the direction indicated on the tool. The selected setting will appear in the window as shown.

Fig. 8

HIGHER -TORQUE - LOWER

SETTING

Fig. 7

Deeper

1/16"

APPLICATIONS

WARNING T o reduce the risk of explo-

sion, electric shock and property damage, always check the work area for hidden pipes and wires before drilling.

Driving Drywall Screws For Screwdrivers Rated up to 4000 RPM

Standard drywall screws are generally designed for attaching drywall to wood studs and 26 through 20-gauge steel studs. MILWAUKEE Screwdrivers are ideal for driving these types of drywall screws. The depth setting is very important. Refer to the guide below for the correct depth setting.

Fig. 10

Correct. Head of screw is

below surface, but does not puncture facing.

Too deep. Head of screw punches hole in drywall surface, making ﬁ nishing difﬁ cult and allowing moisture beneath facing. Decrease depth.

Too shallow. Head of screw extends above drywall face and can not be ﬁ nished off. Increase depth.

NOTE: Use a piece of scrap material to test the different settings before driving screws into workpiece. T o determine a speciﬁ c setting for your application, use a torque wrench to check the correct torque at any particular setting.

For Cat. No. 6780-20

The 6780-20 Screwdriver has a torque setting adjustment collar that may be adjusted to one of twenty-one settings. The torque is adjustable from 10 to 140 inch-pounds. To select a setting, turn the adjustment collar on the tool. The selected setting will appear above the arrow as shown. NOTE: Use a piece of scrap material to test the different settings before driving screws into workpiece. To determine a speciﬁ c setting for your ap- plication, use a torque wrench to check the correct torque at any particular setting.

Fig. 9

1. Select the proper drywall screw for each job. Pilot holes are not needed. T o insert screws, place the screw onto the insert bit, then align the screw against the work surface, making sure to hold the tool and screw square to the work surface.

If the tool or screw are misaligned, the screw will

not drive into the work surface or it will not drive straight.

2. Pull the trigger and push the tool forward with a “punching” motion to sink the screw into the drywall. A punching motion will engage the snap-action clutch, cause the screw to start rotating, sink the screw and disengage the snap-action clutch within a fraction of a second. If pressure is not maintained on the tool after engaging the snapaction clutch, the screw will not properly seat.

The snap-action clutch will automatically disen-

gage and the insert bit will stop rotating once the screw has been driven to the selected depth.

These screwdrivers feature a snap-action clutch,

which may ratchet slightly when the screw is sunk to the selected depth.

NOTE: Practice driving screws into pieces of

scrap material to become familiar with the tool and the snap-action clutch action before attempting to drive screws into the workpiece.

3. T o remove screws, remove the locator assembly and switch the forward/reverse switch to the reverse position. Reattaching the locator assembly will not change the depth setting.

Driving Decking Screws For Screwdrivers with Depth Locators Rated up to 2700 RPM

Standard decking screws are generally designed for attaching wood to wood studs. MILWAUKEE Screwdrivers are ideal for driving these types of decking screws. The depth setting is very important. Refer to the guide below for the correct depth setting.

Fig. 11

Correct. Head of screw is

below surface.

Too deep. Head of screw punches hole in surface, allowing moisture to collect. Decrease depth.

Too shallow . Head of screw extends above surface. Increase depth.

1. Select the proper decking screw for each job. Pilot holes are not needed. To insert screws, place the screw onto the insert bit, then align the screw against the work surface, making sure to hold the tool and screw square to the work surface.

If the tool or screw are misaligned, the screw will

not drive into the work surface or it will not drive straight. Wood screws have sharp points or drill points, and course threads that help the screw through the wood.

2. Pull the trigger and push the tool forward to sink the screw into the wood. A quick motion will engage the snap-action clutch, cause the screw to start rotating, sink the screw and disengage the snap-action clutch within a fraction of a second. If pressure is not maintained on the tool after engaging the snap-action clutch, the screw will not properly seat.

The snap-action clutch will automatically disen-

gage and the insert bit will stop rotating once the screw has been driven to the selected depth.

These screwdrivers feature a snap-action clutch,

which may ratchet slightly when the screw is sunk to the selected depth.

NOTE: Practice driving screws into pieces of

scrap material to become familiar with the tool and the snap-action clutch action before attempting to drive screws into the workpiece.

3. T o remove screws, remove the locator assembly and switch the forward/reverse switch to the reverse position. Reattaching the locator assembly will not change the depth setting.

Driving Self-Drilling Screws into Cold-Formed Steel Framing For Adjustable Torque Screwdrivers Rated up to 2700 RPM

Follow this procedure when working with light gauge sheet metal, 20 gauge and thicker. The screw may hesitate slightly when it ﬁ nishes breaking through the ﬁ rst layer of material and starts to penetrate the sheet metal. This is normal. Keep ﬁ rm pressure on the tool until the screw is fully seated. Self-drilling and self-tapping screws drill, tap and fasten in one quick, easy motion without a sepa-

rate drilling operation. Their unique design works in metal up to 1/2" thick, giving a strong, reliable hold. The drill point ensures rapid drilling and consistently low drilling pressure while the drill ﬂ utes remove drilling chips. The pilot section ensures that drilling is completed before the ﬁ rst thread engages the material. These screws can be used in many applications.

1. Insert screw into the hex socket and align the screw against the work surface.

2. Pull the trigger while pushing the tool forward. This motion will engage the drive clutch, causing the screw to start rotating. If pressure is not maintained on the tool, the drive clutch will disengage and the screw will stop rotating.

When the selected torque

is fully reached, the torque clutch will ratchet. If the screw is not fully seated, increase the torque setting number until the desired torque is obtained.

NOTE: Practice driving

screws into pieces of scrap material to become familiar with the tool and the clutch action before attempting to drive screws into the workpiece.

3. To remove screws, switch

the forward/reverse switch to the reverse position.

Fig. 12

Sheet to sheet

Sheet to structure

Structure to structure

Wood to structure

Corrugated siding

Driving Wood Screws

When driving wood screws, a pilot hole is recommended to make driving easier and to prevent splitting the wood. As a general rule, the pilot hole should have a diameter of approximately 70% the size of the screw diameter. Hardwood pilot holes should have a diameter of approximately 90% the size of the screw diameter. The depth of the pilot hole should be shorter than the length of the screw by at least one screw diameter. This allows the tip of the screw to bite into the wood for extra holding power. Counterbore the top portion of the hole for a free ﬁ t of the shank between the screw head and the threads. When using ﬂ at head screws, countersink the top of the hole to allow the screw head to be driven ﬂ ush with the work surface. Use soap or wax for easier screw insertion if necessary.

MAINTENANCE

WARNING T o reduce the risk of injury,

always unplug your tool before performing any maintenance. Never disassemble the tool or try to do any rewiring on the tool’s electrical system. Contact a MILW AUKEE service facility for ALL repairs.

Maintaining Tools

Keep your tool in good repair by adopting a regular maintenance program. Before use, examine the general condition of your tool. Inspect guards, switches, tool cord set and extension cord for damage. Check for loose screws, misalignment, binding of moving parts, improper mounting, broken parts and any other condition that may affect its safe operation. If abnormal noise or vibration occurs, turn the tool off immediately and have the problem corrected before further use. Do not use a damaged tool. Tag damaged tools “DO NOT USE” until repaired (see “Repairs”). Under normal conditions, relubrication is not necessary until the motor brushes need to be replaced. After six months to one year, depending on use, return your tool to the nearest MILWAUKEE service facility for the following:

• Lubrication

• Brush inspection and replacement

• Mechanical inspection and cleaning (gears, spin-

dles, bearings, housing, etc.)

• Electrical inspection (switch, cord, armature, etc.)

• T esting to assure proper mechanical and electrical

operation

ACCESSORIES

WARNING To reduce the risk of injury ,

always unplug the tool before attaching or removing accessories. Use only speciﬁ cally recommended accessories. Others may be hazardous.

For a complete listing of accessories refer to your MILWAUKEE Electric Tool catalog or go on-line

to www.milwaukeetool.com. To obtain a catalog, contact your local distributor or a service center.

WARNING T o reduce the risk of injury,

electric shock and damage to the tool, never immerse your tool in liquid or allow a liquid to ﬂ ow inside the tool.

Cleaning

Clean dust and debris from vents. Keep the tool handles clean, dry and free of oil or grease. Use only mild soap and a damp cloth to clean your tool since certain cleaning agents and solvents are harmful to plastics and other insulated parts. Some of these include: gasoline, turpentine, lacquer thinner, paint thinner , chlorinated cleaning solvents, ammonia and household detergents containing ammonia. Never use ﬂ ammable or combustible solvents around tools.

Repairs

If your tool is damaged, return the entire tool to the nearest service center.

LIMITED WARRANTY - USA AND CANADA

Every MILWAUKEE power tool (including cordless product – tool, battery pack(s) - see separate & distinct CORDLESS BATTERY PACK LIMITED WARRANTY statements & battery charger and Work Lights*) is warranted to the original purchaser only to be free from defects in material and workmanship. Subject to certain exceptions, MILWAUKEE will repair or replace any part on an electric power tool which, after examination, is determined by MILWAUKEE to be defective in material or workmanship for a period of ﬁ ve (5) years* after the date of purchase unless otherwise noted. Return of the power tool to a MILWAUKEE factory Service Center location or MILWAUKEE Authorized Service Station, freight prepaid and insured, is required. A copy of the proof of purchase should be included with the return product. This warranty does not apply to damage that MILWAUKEE determines to be from repairs made or attempted by anyone other than MILWAUKEE authorized personnel, misuse, alterations, abuse, normal wear and tear, lack of maintenance, or accidents. *The warranty period for, Job Site Radios, M12™ Power Port, M18™ Power Source, and T rade T itan™ Industrial Work Carts is one (1) year from the date of purchase. The warranty period for a LED Work Light and LED Upgrade Bulb is a limited LIFETIME warranty to the original purchaser only, if during normal use the LED bulb fails the Work Light or Upgrade Bulb will be replaced free of charge. *This warranty does not cover Air Nailers & Stapler , Airless Paint Sprayer , Cordless Battery Packs, Gasoline Driven Portable Power Generators, Hand T ools, Hoist – Electric, Lever & Hand Chain, M12™ Heated Jackets, Reconditioned product and T est & Measurement products. There are separate and distinct warranties available for these products. Warranty Registration is not necessary to obtain the applicable warranty on a MILWAUKEE power tool product. The manufacturing date of the product will be used to determine the warranty period if no proof of purchase is provided at the time warranty service is requested. ACCEPTANCE OF THE EXCLUSIVE REPAIR AND REPLACEMENT REMEDIES DESCRIBED HEREIN IS A CONDITION OF THE CONTRACT FOR THE PURCHASE OF EVERY MILWAUKEE PRODUCT. IF YOU DO NOT AGREE TO THIS CONDITION, YOU SHOULD NOT PURCHASE THE PRODUCT. IN NO EVENT SHALL MILWAUKEE BE LIABLE FOR ANY INCIDENTAL, SPECIAL, CONSEQUENTIAL OR PUNITIVE DAMAGES, OR FOR ANY COSTS, ATTORNEY FEES, EXPENSES, LOSSES OR DELAYS ALLEGED TO BE AS A CONSEQUENCE OF ANY DAMAGE TO, FAILURE OF, OR DEFECT IN ANY PRODUCT INCLUDING, BUT NOT LIMITED TO, ANY CLAIMS FOR LOSS OF PROFITS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS WARRANTIES, WRITTEN OR ORAL. TO THE EXTENT PERMITTED BY LAW, MILWAUKEE DISCLAIMS ANY IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE OR PURPOSE; TO THE EXTENT SUCH DISCLAIMER IS NOT PERMITTED BY LAW, SUCH IMPLIED WARRANTIES ARE LIMITED TO THE DURATION OF THE APPLICABLE EXPRESS WARRANTY AS DESCRIBED ABOVE. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU, THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE. This warranty applies to product sold in the U.S.A. and Canada only. Please consult the ‘Service Center Search’ in the Parts & Service section of MILWAUKEE’s website www.milwaukeetool.com or call 1.800.SAWDUST (1.800.729.3878) to locate your nearest service facility for warranty and non-warranty service on a Milwaukee electric power tool.

LIMITED WARRANTY - MEXICO, CENTRAL AMERICA AND CARIBBEAN

TECHTRONIC INDUSTRIES' warranty is for 5 year since the original purchase date. This warranty card covers any defect in material and workmanship on this Power Tool. To make this warranty valid, present this warranty card, sealed/stamped by the distributor or store where you purchased the product, to the Authorized Service Center (ASC). Or, if this card has not been sealed/stamped, present the original proof of purchase to the ASC. Call toll-free 1 800 832 1949 to ﬁ nd the nearest ASC, for service, parts, accessories or components.

Procedure to make this warranty valid

Take the product to the ASC, along with the warranty card sealed/stamped by the distributor or store where you purchased the product, and there any faulty piece or component will be replaced without cost for you. We will cover all freight costs relative with this warranty process.

Exceptions

This warranty is not valid in the following situations: a) When the product is used in a different manners from the end-user guide or instruction manual. b) When the conditions of use are not normal. c) When the product was modiﬁ ed or repaired by people not authorized by TECHTRONIC INDUSTRIES. Note: If cord set is damaged, it should be replaced by an Authorized Service Center to avoid electric risks.

SERVICE AND ATTENTION CENTER

Model:

Rafael Buelna No.1. Col. Tezozomoc Mexico, Azcapotzalco D.F.

Date of Purchase:

Ph. 01 800 832 1949

Distributor or Store Stamp:

IMPORTED AND COMMERCIALIZED BY: TECHTRONIC INDUSTRIES MEXICO, .S.A. DE C.V. Av. Santa Fe 481 piso 6, Col. Curz Manca. CP 05349, Cuajimalpa, D.F.

+ 19 hidden pages